Abstract:Introduction: The cervical spine, pivotal for mobility and overall body function, can be affected by cervical spondylosis, a major contributor to neural disorders. Prevalent in both general and military populations, especially among pilots, cervical spondylosis induces pain and limits spinal capabilities. Anterior Cervical Discectomy and Fusion (ACDF) surgery, proposed by Cloward in the 1950s, is a promising solution for restoring natural cervical curvature. The study objective was to investigate the impacts of ACDF implant design on postsurgical cervical biomechanics and neurorehabilitation outcomes by utilizing a biofield head-neck finite element (FE) platform that can facilitate scenario-specific perturbations of neck muscle activations. This study addresses the critical need to enhance computational models, specifically FE modeling, for ACDF implant design. Materials and methods: We utilized a validated head-neck FE model to investigate spine-implant biomechanical interactions. An S-shaped dynamic cage incorporating titanium (Ti) and polyetheretherketone (PEEK) materials was modeled at the C4/C5 level. The loading conditions were carefully designed to mimic helmet-to-helmet impact in American football, providing a realistic and challenging scenario. The analysis included intervertebral joint motion, disk pressure, and implant von Mises stress. Results: The PEEK implant demonstrated an increased motion in flexion and lateral bending at the contiguous spinal (C4/C5) level. In flexion, the Ti implant showed a modest 5% difference under 0% activation conditions, while PEEK exhibited a more substantial 14% difference. In bending, PEEK showed a 24% difference under 0% activation conditions, contrasting with Ti's 17%. The inclusion of the head resulted in an average increase of 18% in neck angle and 14% in C4/C5 angle. Disk pressure was influenced by implant material, muscle activation level, and the presence of the head. Polyetheretherketone exhibited lower stress values at all intervertebral disc levels, with a significant effect at the C6/C7 levels. Muscle activation level significantly influenced disk stress at all levels, with higher activation yielding higher stress. Titanium implant consistently showed higher disk stress values than PEEK, with an orders-of-magnitude difference in von Mises stress. Excluding the head significantly affected disk and implant stress, emphasizing its importance in accurate implant performance simulation. Conclusions: This study emphasized the use of a biofidelic head-neck model to assess ACDF implant designs. Our results indicated that including neck muscles and head structures improves biomechanical outcome measures. Furthermore, unlike Ti implants, our findings showed that PEEK implants maintain neck motion at the affected level and reduce disk stresses. Practitioners can use this information to enhance postsurgery outcomes and reduce the likelihood of secondary surgeries. Therefore, this study makes an important contribution to computational biomechanics and implant design domains by advancing computational modeling and theoretical knowledge on ACDF-spine interaction dynamics.

Evaluation of finite element modeling methods for predicting compression screw failure in a custom pelvic implant

Finite Element Analysis of the Pelvis after Customized Prosthesis Reconstruction

Optimization Technique and Fe Simulation for Lag Screw Placement in Anterior Column of the Acetabulum

A Finite Element Analysis of the Pelvic Reconstruction Using Fibular Transplantation Fixed with Four Different Rod-Screw Systems after Type I Resection

COMPARISON OF FATIGUE BEHAVIORS OF SPINAL IMPLANTS UNDER PHYSIOLOGICAL SPINAL LOADS: A FINITE ELEMENT PILOT STUDY

Finite element analysis of osteosynthesis screw fixation in the bone stock: an appropriate method for automatic screw modelling

A Novel Screw Modeling Approach to Study the Effects of Screw Parameters on Pullout Strength.

The Effect of Screw Fixation Type on a Modular Hemi-Pelvic Prosthesis: a 3-D Finite Element Model

A Finite Element Model for investigating the influence of keel design and position on unicompartmental knee replacement cementless tibial component fixation

Establishing finite element model credibility of a pedicle screw system under compression-bending: An end-to-end example of the ASME V&V 40 standard

Finite Element Method-Based Study of Pedicle Screw–bone Connection in Pullout Test and Physiological Spinal Loads

The biomechanics of plate repair of periprosthetic femur fractures near the tip of a total hip implant: the effect of cable-screw position

Effect of Bone Remodeling on Dental Implant Fatigue Limit Predicted Using 3D Finite Element Analysis

Three-dimensional finite element analysis of hip joint replacement

A novel personalized homogenous finite element model to predict the pull-out strength of cancellous bone screws

Semi-automated finite element analyses of surgically treated acetabular fractures to investigate the biomechanical behaviour of patient-specific compared to conventional implants

Optimization of S2-alar-iliac screw (S2AI) fixation in adult spine deformity using a comprehensive genetic algorithm and finite element model personalized to patient geometry and bone mechanical properties

[Design of Minimal Invasive Screw on Posterior Pelvis Ring and Pelvic Finite Element Analysis].

In vivo finite element modeling and mechanical analysis of artificial hip joint

Implant Design and Cervical Spinal Biomechanics and Neurorehabilitation: A Finite Element Investigation

Towards Biomechanical Evaluation of a Transformative Additively Manufactured Flexible Pedicle Screw for Robotic Spinal Fixation