Abstract:Background: Temporomandibular joint (TMJ) overloading is considered a primary cause of temporomandibular joint disorders (TMD). Accordingly, craniomaxillofacial structural parameters affect the loading situation in the TMJ. However, no effective method exists for quantitatively measuring the loading variation in human TMJs. Clinical statistics, which draws from general rules from large amounts of clinical data, cannot entry for exploring the underlying biomechanical mechanism in craniomaxillofacial system. The finite element method (FEM) is an effective tool for analyze the stress and load on TMJs for several cases in a short period of time; however, it is difficult to generalize general patterns through calculations between different cases due to the different geometric characteristics and occlusal contacts between each case. Methods: (1) This study included 88 subjects with 176 unilateral data to measure angle (α) of the distance to the plane of occlusion. The bone destruction score was evaluated for clinical statistics. To rule out effects of the potential factors and ensure the generality of the study, one participant with no obvious bone destruction was selected as the standard case for establishing the three-dimensional (3D) theoretical model and FEM. (2) Three groups of forces, including biting, muscles and joint reaction forces on mandible, were adopted to establish a 3D theoretical model. (3) By modifying the sagittal α and coronal three types of deviation angle (φ) of the original model, nine candidate models were obtained for the FEM studies. Results: (1) The static equilibrium equations, were used to establish a 3D theoretical model for describing the loading of the TMJ. The theoretical model was validated by monotonously modifying the structural parameter in comparison to two-dimensional theoretical models reported previously; (2) The force on the TMJ gradually decreased with α, and this trend was validated by both clinic statistics and FEM results; (3) The effects of the three types of deviation angle were different. The results of the case where only rotating biting forces were considered was consistent with clinical statistics, indicating that the side with lower α experiences higher TMJ load. (4) Changing the unilateral proportionality coefficients of biting and muscle force produced opposite effects, wherein the effects of the muscle force were stronger than those of the biting forces. Conclusions: A negative correlation was observed between the joint load and α. Among the three types of asymmetric deformities, occlusal deviations were the primary factors leading to TMD. Unilateral occlusion can result in a greater load on the ipsilateral joint and should be avoided when using the side corresponding to the TMD. This study provides a theoretical basis for the biomechanical mechanism of TMD and also enables the targeted mitigation and treatment of TMD through structural modification.

Assessment of the relationship between the three-dimensional precise location of the mandibular third molar and the volume ratio of the impacted mandibular third molar to the mandibular angle, and the patterns of mandibular angle fracture: A retrospective study

Does the presence of mandibular third molars increase the risk of angle fracture and simultaneously decrease the risk of condylar fracture?

A finite element analysis on the indication for extracting partially impacted mandibular third molars considering mandibular trauma

Analysis of Relative Factor's on the Mandibular Angle Fracture

Three-dimensional analysis of the relationship between mandibular retromolar space and positional traits of third molars in non-hyperdivergent adults

The factors affecting mandibular third molar angulation during orthodontic treatment

Effect of mesioangular impaction of the mandibular third molars on the adjacent mandibular second molars: An imaging study.

Pathologies associated with the mandibular third molar impaction

Relationship between Presence of Third Molars and Prevalence of Periodontal Pathology of Adjacent Second Molars: a Systematic Review and Meta-analysis

Relationship between the impacted mandibular third molar and adjacent second molar' external root resorption by cone-bean computed tomography analysis

Three-dimensional analysis of mandibular and mental canals corroborating with teeth and mental foramen by cone beam computed tomography

Three-dimensional theoretical model for effectively describing the effect of craniomaxillofacial structural factors on loading situation in the temporomandibular joint

A Clinical Investigation on Disc Displacement in Sagittal Fracture of the Mandibular Condyle and Its Association with TMJ Ankylosis Development

Relationship between Impacted Mandibular Third Molars and the Mandibular Canal on CBCT Scans

The impact of Anatomic Features of Asymptomatic Third Molars on the Pathologies of Adjacent Second Molars: A Cross-sectional Analysis

The Three-Dimensional Investigation of the Radiographic Boundary of Mandibular Full-Arch Distalization in Different Facial Patterns

Is prophylactic extraction of mandibular third molar indicated? A retrospective study.

The relationship of the position of mandibular third molar impaction with the development of dental and periodontal lesions in adjacent second molars

Is it necessary to remove bone-impacted teeth? A retrospective study

Analysis of the Influencing Multi-factors on the Mandibular Third Molar Extraction

Biomechanical Evaluation of the Mandibular First Molar After Simulated Occlusal Wear Using 3D Finite Element Analysis