Abstract:The combination of biocompatible materials and advanced three-dimensional (3D) additive manufacturing technologies holds great potential in the development of finely tuned complex scaffolds with reproducible macro- and micro-structural characteristics for biomedical applications, such as tissue engineering and drug delivery. In this study, biocompatible printable inks based on chitosan, collagen and gelatin were developed and 3D-printed with a pneumatic-based extrusion printer. The printability of various chitosan-gelatin (CS-Gel) hydrogel inks was assessed by evaluating the quality of the printed constructs. The inks required an extrusion pressure of 150 ± 40 MPa with G22 and G25 nozzles for optimal printing. Inks with low chitosan concentrations (<4% w/v) exhibited poor printability, while inks with 4 % w/v chitosan and 1 % w/v gelatin (CG) demonstrated satisfactory extrusion and printing quality. The addition of collagen (0.1 % w/v) to the optimized ink (CGC) did not compromise printability. Post-printing stabilization using KOH produced self-supporting scaffolds with consistent morphological integrity, while weaker bases like NaOH/EtOH and ammonia vapors resulted in lower pore sizes and reduced structural stability. Water evaporation studies showed that neutralized samples had slower evaporation rates due to the strong intermolecular interactions formed during the neutralization process, contributing to a stable crosslinked network. FTIR spectra confirmed the formation of polyelectrolyte complexes in the CS-Gel and CS-Gel-Collagen blends, further enhancing structural stability. Swelling tests indicated that neutralized constructs maintained stability in different pH environments, with KOH-treated samples exhibiting the lowest swelling ratios and the highest structural stability. After optimizing the ink composition, 10 wt% Levofloxacin was loaded in the constructs as a model antibiotic and it's in vitro release rate was quantified. Drug loading was approximately 4 % for both ink compositions GC and CGC. CG Levo released over 80 % of levofloxacin within the first hour, reaching full release in 24 h, indicating inadequate control, while CGK Levo exhibited slower initial release (55 % in 15 min) followed by stabilized release after 4 h, likely due to controlled diffusion from expanded constructs. These findings demonstrate that the developed hydrogel inks and optimized printing parameters can produce scaffolds suitable for tissue engineering applications. Finally, the cell compatibility of the 3D-printed constructs was confirmed with MTT assay on fibroblasts and the antimicrobial activity of the drug-loaded constructs was tested against E. coli and S. aureus, showing an increase of the bacteria free zone from 8 ± 0.4 mm of the control against E. coli up to 16.4 ± 0.37 mm in the presence of the KOH-treated CG Levo printed construct.

Effect of active carbonyl-carboxyl ratio on dynamic Schiff base crosslinking and its modulation of high-performance oxidized starch-chitosan hydrogel by hot extrusion 3D printing

Simulations of Extrusion 3D Printing of Chitosan Hydrogels

Dimethyl Sulfoxide Mediated High-Fidelity 3D Printing of Hydrogels

3D-printing of oxidized starch-based hydrogels with superior hydration properties

Integrated Rapid-Prototyping and Strength-Increasing All-in-one 3D Printing of Chitosan Hydrogels

Effect of Starch Molecular Structure on Precision and Texture Properties of 3D Printed Products

3D Printing of High-Strength Chitosan Hydrogel Scaffolds Without Any Organic Solvents.

Printability Improvement of Rice Starch Gel Via Catechin and Procyanidin in Hot Extrusion 3D Printing

Dual Ionically Cross-linked Double-Network Hydrogels with High Strength, Toughness, Swelling Resistance, and Improved 3D Printing Processability

Ink Based on the Tunable Swollen Microsphere for a 3D Printing Hydrogel with Broad-Range Mechanical Properties

Evaluation of different crosslinking methods in altering the properties of extrusion-printed chitosan-based multi-material hydrogel composites

An Optimization Study of 3D Printing Technology Utilizing a Hybrid Gel System Based on Astragalus Polysaccharide and Wheat Starch

Synthesis and Characterization of Starch-Based Acid- and Alkali-Resistant Hydrogels Optimized by Box–Behnken Response Surface Methodology

3D Printing of Dual-Physical Cross-linking Hydrogel with Ultrahigh Strength and Toughness

Stabilization of capsanthin in physically-connected hydrogels: Rheology property, self-recovering performance and syringe/screw-3D printing

Preparation of 3D Printed Chitosan/Polyvinyl Alcohol Double Network Hydrogel Scaffolds.

Co-encapsulation of hydrophilic and hydrophobic bioactives stabilized in nanostarch-assisted emulsion for inner core gel of coaxial 3D printing

Optimization of chitosan-gelatin-based 3D-printed scaffolds for tissue engineering and drug delivery applications

Research on rice starch gel preparation and crosslink network structure-rheological property based on direct-writing 3D printing

Loose Pre-Cross-Linking Mediating Cellulose Self-Assembly for 3D Printing Strong and Tough Biomimetic Scaffolds

Direct 3D printing of thermosensitive AOP127-oxidized dextran hydrogel with dual dynamic crosslinking and high toughness