Abstract:Objective In this study, we used frontal and lateral cephalograms combining laser scanning of the the facial soft tissue as the sources of the information to develope the integrated 3D model of the craniofacial hard and soft tissues. Methods ①Setting lead points on the face.Lead a total of five points, distributed in a"+"-like character in both directions,that is,the direction of the center line and Frankfort plane direction.②Shooting frontal and lateral cephalograms.It is necessary to ensure that the posture of the head is level and the teeth are in contact.③To establish the 3D model of the Cranialfacial hard tissue.Take the skull from Asians with integrity structures and clear surface as a standard model,then establish the 3D coordinate system.Adjust to the X- ray films and the coordinates of the line. In the standard model of the skull,set 54 feature points as the initial feature points.Then take a adjustment of the location of these points in the frontal and lateral cephalograms, as the target feature points,ensuring that both the positions defined are in correspondence.Based on a certain deformation algorithm,deform the standard skull model according to the feature points established in the X-ray films,then the model of craniofacial hard tissue in patient is achieved.④Laser scanning of facial soft tissue.A total of three screens are shot including the median facial image and the ones from about 45 degrees in the left and right.⑤Facial soft tissue reconstruction.The three screens by scanning are pretreated,then synthesize the complete 3D model of soft tissue.⑥Fitting of the soft and hard tissues. Fit the facial soft tissue and bone tissue models together according to the lead coordinates. Results ①The 3D model that reflects the surface construction of the craniofacial hard tissue was constructed.②The fitting of the hard and soft tissues came ture.The 3D image of the model constructed showed a lively and visual screen of the craniofacial structures, and can be observed from any directions. It laid the foundation of the further orthognathic surgery simulation and morphology prediction. Conclusion ①Compared with the CT reconstruction, the system easily access to the information sources,radiation hazards small,although was not as accurate as CT,but the key regions of the model were anastomosis to the surgery patients.It will achieve some kind of application in the future.②3D laser scanning is the most advanced method of accessing to soft tissue, this study had a fitting of the soft and hard tissues,real and reliable.

Research and application discussion of cranial bone model preparation method based on three-dimensional reconstruction and 3D printing technology

[Application of Three-Dimensional Printing Technique in Repair and Reconstruction of Maxillofacial Bone Defect].

Three dimensional printing technology in neurosurgery

The process of 3D-printed skull models for the anatomy education

Application of three-dimensional printed skull in the teaching of human anatomy

Application of three-dimensional printing technology in orthopedics of craniosynostosis

Preparation of Simulate Craniocerebral Models Via Three Dimensional Printing Technique

Research on 3D Modeling Technology of Craniofacial Implants Based on Topology Optimization Method

The manufacturing procedure of 3D printed models for endoscopic endonasal transsphenoidal pituitary surgery

THE APPLICATION OF RAPID PROTOTYPING IN THE ORTHOGNATHIC SURGERY

Three-dimensional Printing Technologies in Craniofacial Plastic Surgery: an Institutional Experience.

3D Printing Technology-Assisted Endoscopy Surgery in the Treatment of Skull Base Tumors : A retrospective study

Development of Three-Dimensional Printed Craniocerebral Models for Simulated Neurosurgery.

The Role of Three-Dimensional Printed Models of Skull in Anatomy Education: a Randomized Controlled Trail

Development of 3D Printed Craniocerebral Models for Simulated Neurosurgery.

Study on 3D model of the craniofacial structures by 2D X-ray method

Construction of cyno-mandibular condyle models using three-dimensional imaging and rapid prototyping technology

A preliminary exploration of the application of 3D modeling and printing technology for the con-struction of clinical teaching models in the department of orthopedic trauma

Patient-specific Composite Anatomic Models: Improving the Foundation for Craniosynostosis Repair

3D Printing in Cranioplasty for Giant Cranial Deformity with Multi-Dimensional Nuclear Magnetic Simulation

The utility of 3-dimensional-printed models for skull base meningioma surgery