Abstract:Statement of problem: Evidence regarding stress evaluations of removable obturators with Aramany class I defects is lacking. Whether the stress distribution on Aramany class I prostheses can be improved by modifying the currently used designs is also unclear. Purpose: The purpose of part II of this study was to evaluate the stress distribution in different designs of Aramany class I obturators using finite element analysis (FEA) and photoelastic stress analysis. Material and methods: Four finite element and 8 photoelastic models, including 2 acrylic resin base obturators retained with 2 Adams clasps, 2 linear, 2 tripodal, and 2 fully tripodal design obturators, were used in this study. The frameworks were fabricated on the casts obtained from a modified printed model. Vertical and oblique loads were applied on 2 points (anterior and posterior) of the models. The quantitative measurement was done by measuring the fringe orders and von Mises values to compare the influences of occlusal forces on the obturator components and their supporting structures. The qualitative evaluation was done by visual color mapping to identify the stress concentration. Results: In the photoelastic analysis, the anterior abutments of the tripodal showed the highest stress, followed by the fully tripodal obturators, while, in FEA, the anterior abutments of the linear design received the most in both vertical and oblique load. The central incisor received the most stress in photoelastic (3 or more fringe orders) and FEA (687.3 and 150.1 MPa for vertical and oblique loads, respectively), followed by the lateral incisors. Upon posterior loading, the base of the defect of the linear design demonstrated the most stress in photoelastic (3 or more fringes) and FEA (94.3 and 130.5 MPa for vertical and oblique loads, respectively). The acrylic resin base obturator retained with Adams clasps demonstrated the lowest stress distribution in abutments and their supporting bone upon anterior and posterior loads. Conclusions: Upon vertical and oblique load application, the fully tripodal design was comparable with the tripodal in terms of stress distribution. Both designs were better than the linear in response to the same loading. The stress was concentrated at the anterior palatal part of the obturator, the base of the defect, and the junction of the metal and acrylic resin part of the prostheses upon anterior and posterior loading, respectively.

The Compassion–Hostility Paradox

Stress Distribution Pattern in Mini Dental Implant-Assisted RPD with Different Clasp Designs: 3D Finite Element Analysis

Stress Analysis for Different Designs of Implant-borne and Tooth-implant Fixed Partial Dentures in Mandibular Posterior Region

An in vitro assessment of optimizing implant positions in bilateral distal extension implant-assisted removable partial dentures: A microstress analysis

Effect of Number and Location on Stress Distribution of Mini Dental Implant-Assisted Mandibular Kennedy Class I Removable Partial Denture: Three-Dimensional Finite Element Analysis

Stress distribution of single-implant-retained overdenture reinforced with a framework: A finite element analysis study

Effect of two esthetic digitally produced materials used in fabrication of extracoronal attachments on the stresses Induced in removable partial dentures

[Influence of attachment type on stress distribution of implant-supported removable partial dentures].

Evaluation of the biomechanics of Aramany class I obturators of different designs using numerical and experimental methods. Part II: Stress distribution

Assessment of stress shielding around a dental implant for variation of implant stiffness and parafunctional loading using finite element analysis

Effect of different occlusal materials on peri-implant stress distribution with different osseointegration condition: A finite element analysis

Overdenture retaining bar stress distribution: A finite-element analysis

Effect of different framework materials on stresses induced in distal extension removable partial dentures: A strain gauge analysis

Comparison of stress distribution around splinted and nonsplinted implants with different crown height space in posterior mandible: A finite element analysis study

The importance of properly distributing the occlusal load for the correct biomechanics of implant-supported fixed partial dentures: stress analysis in implants, prosthetic components and infrastructures

Stress analysis of different prosthesis materials in implant-supported fixed dental prosthesis using 3D finite element method

Stress influence on orthodontic system components under simulated treatment loadings

STRESS ANALYSIS STUDIES WITH DENTAL IMPLANTS, DIFFERENT SITUATIONS AND CONNECTIONS WITH NATURAL TEETH

Effect of Implant-Abutment Connection and Abutment Angulations on Peri-implant Stress Levels: A Finite Element Analysis Study

Biomechanical Analysis of Stress Distribution and Failure Risk in Mandibular Incisors Restored with Resin-Bonded Fixed Partial Dentures Using CAD/CAM Materials and Restoration Designs

The Effect of Different Abutment Designs and Materials on Stress Distribution in Implants and Peripheral Bones: A Three-Dimensional Finite Element Analysis