Abstract:Whereas freeze-drying is a widely used method to produce porous hydrogel scaffolds, the mechanisms of pore formation involved in this process remained poorly characterized. To explore this, we focused on a cross-linked polysaccharide-based hydrogel developed for bone tissue engineering. Scaffolds were first swollen in 0.025% NaCl then freeze-dried at low cooling rate, i.e. - 0.1 °C min-1, and finally swollen in solvents of increasing ionic strength. We found that scaffold's porous structure is strongly conditioned by the nucleation of ice. Electron cryo-microscopy of frozen scaffolds demonstrates that each pore results from the growth of one to a few ice grains. Most crystals were formed by secondary nucleation since very few nucleating sites were initially present in each scaffold (0.1 nuclei cm-3 °C-1). The polymer chains are rejected in the intergranular space and form a macro-network. Its characteristic length scale coincides with the ice grain size (160 <math>μm</math>) and is several orders of magnitude greater than the mesh size (90 nm) of the cross-linked network. After sublimation, the ice grains are replaced by macro-pores of 280 <math>μm</math> mean size and the resulting dry structure is highly porous, i.e. 93%, as measured by high-resolution X-ray tomography. In the swollen state, the scaffold mean pore size decreases in solvent of increasing ionic strength (120 µm in 0.025% NaCl and 54 µm in DBPS) but the porosity remains the same, i.e. 29% regardless of the solvent. Finally, cell seeding of dried scaffolds demonstrates that the pores are adequately interconnected to allow homogenous cell distribution.<h3>Statement of significance</h3>The fabrication of hydrogel scaffolds is an important research area in tissue engineering. Hydrogels are textured to provide a 3D-framework that is favorable for cell proliferation and/or differentiation. Optimum hydrogel pore size depends on its biological application. Producing porous hydrogels is commonly achieved through freeze-drying. However, the mechanisms of pore formation remain to be fully understood. We carefully analyzed scaffolds of a cross-linked polysaccharide-based hydrogel developed for bone tissue engineering, using state-of-the-art microscopic techniques. Our experimental results evidenced the shaping of hydrogel during the freezing step, through a specific ice-templating mechanism. These findings will guide the strategies for controlling the porous structure of hydrogel scaffolds.

Structure and mechanical properties of anisotropic agar gels obtained via unidirectional freezing

Preparation of Poly(ethylene Glycol) Aligned Porous Cryogels Using a Unidirectional Freezing Technique

Ice-crystal Formation in Gelatin Gel During Pressure Shift Versus Conventional Freezing

Characterizing High Pressure Phase Transitions of Gelatin Gel and Assessing Microstructural, Gel Properties, and Texture Changes Following Pressure Shift Freezing and Ice I to Ice III Phase Transition

Morphology of optically anisotropic agarose hydrogel prepared by directional freezing

Deformation of hydrogel during freezing

Interplay between crosslinking and ice nucleation controls the porous structure of freeze-dried hydrogel scaffolds

Overcooked agar solutions: impact on the structural and mechanical properties of agar gels

Freezing as a path to build macroporous structures: Superfast responsive polyacrylamide hydrogels

Normal force controlled rheology applied to agar gelation

Anisotropic nanocellulose aerogels with ordered structures fabricated by directional freeze-drying for fast liquid transport

Batch versus microfluidic emulsification processes to produce whey protein microgel beads from thermal or acidic gelation

Mechanisms of pore formation in hydrogel scaffolds textured by freeze-drying

Reversibility in the Physical Properties of Agarose Gels following an Exchange in Solvent and Non-Solvent

Behavior of colloidal gels made of thermoresponsive anisotropic nanoparticles

Cold-Set Globular Protein Gels: Interactions, Structure and Rheology as a Function of Protein Concentration

Tuning structural and mechanical anisotropy of PVA hydrogels

Freezing Molecular Orientation under Stretch for High Mechanical Strength but Anisotropic Hydrogels.

Mechanical properties of agarose hydrogels tuned by amphiphilic structures

Alteration of the structural properties of inulin gels

Single Ice Crystal Growth with Controlled Orientation during Directional Freezing