Abstract:The liquid-phase exfoliation (LPE) of black phosphorus (BP) is a strategic route for the large-scale production of phosphorene and few-layer BP (FL-BP) flakes. The exploitation of this exfoliated material in cutting-edge technologies, e.g., in flexible electronics and energy storage, is however limited by the fact that the LPE of BP is usually carried out at a high boiling point and in toxic solvents. In fact, the solvent residual is detrimental to device performance in real applications; thus, complete solvent removal is critical. Here, we tackle these issues by exfoliating BP in different low boiling-point solvents. Among these solvents, we find that acetone also provides a high concentration of exfoliated BP, leading to the production of FL-BP flakes with an average lateral size and thickness of c.a. 30 and 7 nm, respectively. The use of acetone to produce less defective few-layer BP flakes (FL-BPacetone) from bulk crystals is a straightforward process which enables the rapid preparation of homogeneous thin films thanks to the fast solvent evaporation. The ratio of edge to bulk atoms for the BP flakes here produced, combined with the use of low-boiling-point solvents for the exfoliation process suggests that these thin films are promising anodes for lithium-ion batteries. To this end, we tested Li-ion half cells with FL-BPacetone anodes achieving a reversible specific capacity of 480 mAh/g at a current density of 100 mA/g, over 100 charge/discharge cycles. Moreover, a reversible specific capacity of 345 mAh/g is achieved for the FL-BPacetone-based anode at a high current density (i.e., 1 A/g). These findings indicate that the FL-BPacetone-based battery is promising with regards to the design of fast charge/discharge devices. Overall, the presented process is a step forward toward the fabrication of phosphorene-based devices.

Hummers' method-assisted liquid-phase exfoliation enables the fabrication of few-layer borophene from bulk boron

Borophene via Micromechanical Exfoliation

Liquid-Phase Exfoliation of Hexagonal Boron Nitride into Boron Nitride Nanosheets in Common Organic Solvents with Hyperbranched Polyethylene as Stabilizer

A new route to electrochemical exfoliation of borophene for scalable production

An Ultrahigh Pressure Homogenization Technique for Easily Exfoliating Few-Layer Phosphorene from Bulk Black Phosphorus

Progress in the synthesis of 2D black phosphorus beyond exfoliation

A peeling approach for integrated manufacturing of large mono-layer h-BN crystals

Exfoliation of Few-Layer Black Phosphorus in Low-Boiling-Point Solvents and Its Application in Li-Ion Batteries

Scalable Clean Exfoliation of High‐Quality Few‐Layer Black Phosphorus for a Flexible Lithium Ion Battery

A sustainable and efficient strategy for stable three-layered borophene fabrication

Alkene-Catalyzed Rapid Layer-by-Layer Thinning of Black Phosphorus for Precise Nanomanufacturing

Preparation of Few Layers Hexagonal Boron Nitride Nanosheets Via High-Pressure Homogenization

Few-layer Borophene Prepared by Mechanical Resonance and Its Application in Terahertz Shielding.

Production of High-Quality and Large Lateral-Size Black Phosphorus Nanoparticles/nanosheets by Liquid-Phase Exfoliation

Structural Characterization of Boron Sheets Beyond the Monolayer and Implication for Experimental Synthesis and Identification.

Liquid Exfoliation of Solvent-Stabilized Few-Layer Black Phosphorus for Applications Beyond Electronics.

Hydrogen-assisted Growth of Single Crystalline Borophene Investigated by First-principles Calculations

Solvent Exfoliation of Electronic-Grade, Two-Dimensional Black Phosphorus

Macroscopic Single-Phase Monolayer Borophene on Arbitrary Substrates

Hydrothermal Exfoliation for Two-Dimension Boron Nitride Nanosheets

Synthesis of bilayer borophene