Abstract:Meniscus deficiency, the most common and refractory disease in human knee joints, often progresses to osteoarthritis (OA) due to abnormal biomechanical distribution and articular cartilage abrasion. However, due to its anisotropic spatial architecture, complex biomechanical microenvironment, and limited vascularity, meniscus repair remains a challenge for clinicians and researchers worldwide. In this study, we developed a 3D printing-based biomimetic and composite tissue-engineered meniscus scaffold consisting of polycaprolactone (PCL)/silk fibroin (SF) with extraordinary biomechanical properties and biocompatibility. We hypothesized that the meticulously tailored composite scaffold could enhance meniscus regeneration and cartilage protection.Methods: The physical property of the scaffold was characterized by scanning electron microscopy (SEM) observation, degradation test, frictional force of interface assessment, biomechanical testing, and fourier transform infrared (FTIR) spectroscopy analysis. To verify the biocompatibility of the scaffold, the viability, morphology, proliferation, differentiation, and extracellular matrix (ECM) production of synovium-derived mesenchymal stem cell (SMSC) on the scaffolds were assessed by LIVE/DEAD staining, alamarBlue assay, ELISA analysis, and qRT-PCR. The recruitment ability of SMSC was tested by dual labeling with CD29 and CD90 by confocal microscope at 1 week after implantation. The functionalized hybrid scaffold was then implanted into the meniscus defects on rabbit knee joint for meniscus regeneration, comparing with the Blank group (no scaffold) and PS group. The regenerated meniscus tissue was evaluated by histological and immunohistochemistry staining, and biomechanical test. Macroscopic and histological scoring was performed to assess the outcome of meniscus regeneration and cartilage protection in vivo.Results: The combination of SF and PCL could greatly balance the biomechanical properties and degradation rate to match the native meniscus. SF sponge, characterized by fine elasticity and low interfacial shear force, enhanced energy absorption capacity of the meniscus and improved chondroprotection. The SMSC-specific affinity peptide (LTHPRWP; L7) was conjugated to the scaffold to further increase the recruitment and retention of endogenous SMSCs. This meticulously tailored scaffold displayed superior biomechanics, structure, and function, creating a favorable microenvironment for SMSC proliferation, differentiation, and extracellular matrix (ECM) production. After 24 weeks of implantation, the histological assessment, biochemical contents, and biomechanical properties demonstrated that the polycaprolactone/silk fibroin-L7 (PS-L7) group was close to the native meniscus group, showing significantly better cartilage protection than the PS group.Conclusion: This tissue engineering scaffold could greatly strengthen meniscus regeneration and chondroprotection. Compared with traditional cell-based therapies, the meniscus tissue engineering approach with advantages of one-step operation and reduced cost has a promising potential for future clinical and translational studies.

[Construction of a novel tissue engineered meniscus scaffold based on low temperature deposition three-dimenisonal printing technology]

Biomechanically, structurally and functionally meticulously tailored polycaprolactone/silk fibroin scaffold for meniscus regeneration

3D cell-printing of biocompatible and functional meniscus constructs using meniscus-derived bioink.

Precision 3D printed meniscus scaffolds to facilitate hMSCs proliferation and chondrogenic differentiation for tissue regeneration

3D bioprinting of a biomimetic meniscal scaffold for application in tissue engineering

A three-dimensional printed silk-based biomimetic tri-layered meniscus for potential patient-specific implantation

Meniscal transplantation and regeneration using functionalized polyurethane bionic scaffold and digital light processing 3D printing

Characterization of Decellularized Scaffold Derived from Porcine Meniscus for Tissue Engineering Applications

Biomimetic 3D printed scaffolds for meniscus tissue engineering

Development of decellularized meniscus extracellular matrix and gelatin/chitosan scaffolds for meniscus tissue engineering.

3D-printed variable stiffness tissue scaffolds for potential meniscus repair

Biofabrication of cell-free dual drug-releasing biomimetic scaffolds for meniscal regeneration

Cell-free 3D Wet-Electrospun PCL/silk Fibroin/sr2+ Scaffold Promotes Successful Total Meniscus Regeneration in a Rabbit Model

Preparation and Characterization of an Optimized Meniscal Extracellular Matrix Scaffold for Meniscus Transplantation

3D Printing of Mechanically Functional Meniscal Tissue Equivalents Using High Concentration Extracellular Matrix Inks

The Design and Characterization of a Strong Bio-Ink for Meniscus Regeneration

Printability Optimization of Gelatin-Alginate Bioinks by Cellulose Nanofiber Modification for Potential Meniscus Bioprinting

Meniscus ECM‐functionalised hydrogels containing infrapatellar fat pad‐derived stem cells for bioprinting of regionally defined meniscal tissue

3D-printed cell-free PCL–MECM scaffold with biomimetic micro-structure and micro-environment to enhance in situ meniscus regeneration

3D Printed Elastomer‐Hydrogel Composite Meniscal Scaffolds with Biomimetic Gradient Structure and Robust Interface for Preventing Osteoarthritis and Repairing Meniscal Injuries

Cell-Free Decellularized Skin Matrix Scaffolds: A Promising Approach for Meniscus Regeneration in a Rabbit Meniscectomy Model