Abstract:Meniscus deficiency, the most common and refractory disease in human knee joints, often progresses to osteoarthritis (OA) due to abnormal biomechanical distribution and articular cartilage abrasion. However, due to its anisotropic spatial architecture, complex biomechanical microenvironment, and limited vascularity, meniscus repair remains a challenge for clinicians and researchers worldwide. In this study, we developed a 3D printing-based biomimetic and composite tissue-engineered meniscus scaffold consisting of polycaprolactone (PCL)/silk fibroin (SF) with extraordinary biomechanical properties and biocompatibility. We hypothesized that the meticulously tailored composite scaffold could enhance meniscus regeneration and cartilage protection.Methods: The physical property of the scaffold was characterized by scanning electron microscopy (SEM) observation, degradation test, frictional force of interface assessment, biomechanical testing, and fourier transform infrared (FTIR) spectroscopy analysis. To verify the biocompatibility of the scaffold, the viability, morphology, proliferation, differentiation, and extracellular matrix (ECM) production of synovium-derived mesenchymal stem cell (SMSC) on the scaffolds were assessed by LIVE/DEAD staining, alamarBlue assay, ELISA analysis, and qRT-PCR. The recruitment ability of SMSC was tested by dual labeling with CD29 and CD90 by confocal microscope at 1 week after implantation. The functionalized hybrid scaffold was then implanted into the meniscus defects on rabbit knee joint for meniscus regeneration, comparing with the Blank group (no scaffold) and PS group. The regenerated meniscus tissue was evaluated by histological and immunohistochemistry staining, and biomechanical test. Macroscopic and histological scoring was performed to assess the outcome of meniscus regeneration and cartilage protection in vivo.Results: The combination of SF and PCL could greatly balance the biomechanical properties and degradation rate to match the native meniscus. SF sponge, characterized by fine elasticity and low interfacial shear force, enhanced energy absorption capacity of the meniscus and improved chondroprotection. The SMSC-specific affinity peptide (LTHPRWP; L7) was conjugated to the scaffold to further increase the recruitment and retention of endogenous SMSCs. This meticulously tailored scaffold displayed superior biomechanics, structure, and function, creating a favorable microenvironment for SMSC proliferation, differentiation, and extracellular matrix (ECM) production. After 24 weeks of implantation, the histological assessment, biochemical contents, and biomechanical properties demonstrated that the polycaprolactone/silk fibroin-L7 (PS-L7) group was close to the native meniscus group, showing significantly better cartilage protection than the PS group.Conclusion: This tissue engineering scaffold could greatly strengthen meniscus regeneration and chondroprotection. Compared with traditional cell-based therapies, the meniscus tissue engineering approach with advantages of one-step operation and reduced cost has a promising potential for future clinical and translational studies.

The Design and Characterization of a Strong Bio-Ink for Meniscus Regeneration

Biomechanically, structurally and functionally meticulously tailored polycaprolactone/silk fibroin scaffold for meniscus regeneration

An Injectable Antibacterial Wet-Adhesive for Meniscal Cartilage Regeneration Via Immune Homeostasis Mediated by SMSC-derived Extracellular Vesicles

3D Printing of Mechanically Functional Meniscal Tissue Equivalents Using High Concentration Extracellular Matrix Inks

[Construction of a novel tissue engineered meniscus scaffold based on low temperature deposition three-dimenisonal printing technology]

Meniscus ECM‐functionalised hydrogels containing infrapatellar fat pad‐derived stem cells for bioprinting of regionally defined meniscal tissue

Regional specific tunable meniscus decellularized extracellular matrix (MdECM) reinforced bioink promotes anistropic meniscus regeneration

3D bioprinting of a biomimetic meniscal scaffold for application in tissue engineering

Photocrosslinkable silk-based bioinks embedded with growth factor loaded microspheres towards cell-free 3D printing approach for biomimetic regeneration of meniscal tissue

Meniscal transplantation and regeneration using functionalized polyurethane bionic scaffold and digital light processing 3D printing

Biofabrication of cell-free dual drug-releasing biomimetic scaffolds for meniscal regeneration

3D printing stiff antibacterial hydrogels for meniscus replacement

Preparation and Characterization of an Optimized Meniscal Extracellular Matrix Scaffold for Meniscus Transplantation

3D Printed Elastomer‐Hydrogel Composite Meniscal Scaffolds with Biomimetic Gradient Structure and Robust Interface for Preventing Osteoarthritis and Repairing Meniscal Injuries

Meniscal Scaffolds Based on Self-Healable Elastomer-Hydrogel Composites with Biomimetic Structure and Tribological Properties for Repairing Meniscal Injuries

3D bioprinting by reinforced bioink based on photocurable interpenetrating networks for cartilage tissue engineering

Cell-free 3D Wet-Electrospun PCL/silk Fibroin/sr2+ Scaffold Promotes Successful Total Meniscus Regeneration in a Rabbit Model

Robust Tetra‐armed Poly (ethylene Glycol)‐based Hydrogel As Tissue Bioadhesive for the Efficient Repair of Meniscus Tears

Biodegradable Tyramine Functional Gelatin/6 Arms-PLA Inks Compatible with 3D Two Photon-Polymerization Printing and Meniscus Tissue Regeneration

A three-dimensional printed silk-based biomimetic tri-layered meniscus for potential patient-specific implantation

Repair of a Meniscal Defect in a Rabbit Model Through Use of a Thermosensitive, Injectable, In Situ Crosslinked Hydrogel With Encapsulated Bone Mesenchymal Stromal Cells and Transforming Growth Factor β1