Abstract:Solid-state lithium metal batteries attract much attention for their high theoretical specific capacity and safety. However, the poor interfacial combination between the solid electrolyte (SE) and Li anode usually results in unavoidable growth of Li dendrites and interfacial side reactions. In this work, we propose a simple and effective strategy to modify the interface of the electrolyte/Li anode by scraping a graphite layer on the electrolyte surface facing the anode. The graphite-modified solid electrolyte (G-SE) has a high electrochemical potential window exceeding 4.6 V and high ion conductivity of 3.08 × 10–4 S·cm–2 at ambient temperature. This G-SE membrane is suitable for high-voltage solid-state lithium metal batteries, the assembled NCM622/G-SE/Li cell shows an initial capacity of 160 mAh/g at 0.5 C and a retention capacity of 100 mAh/g after 200 cycles. The good electrochemical performance is attributed to the graphite interfacial modification; the graphite coating and Li can spontaneously react to form a LiC6 layer, which improves the SE/Li interfacial combination and suppresses the growth of lithium dendrites and interfacial side reactions.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acssuschemeng.0c05153?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acssuschemeng.0c05153</a>.EDS point analysis for the Li sheet after cycling (Figure S1); enlarged images of <a class="internalNav" href="#fig6">Figure </a><a class="internalNav" href="#fig6">6</a>a (Figure S2); battery case with test window (Figure S3); C 1s XPS spectrum of the Li sheet with graphite after cycling (Figure S4); lithium metal optical microscope image (Figure S5); digital photo of the lithium metal after 24 h of lithium/G-SE/lithium battery shelving (Figure S6); and the ion transport number calculation table (Table S1) (<a class="ext-link" href="/doi/suppl/10.1021/acssuschemeng.0c05153/suppl_file/sc0c05153_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Nitrogen-Doped Carbon Nanothin Film as a Buffer Layer between Anodic Graphite and Solid Electrolyte Interphase for Lithium-Ion Batteries

Li metal coated with Li3PO4 film via atomic layer deposition as battery anode

Ultrathin graphitic C3N4 lithiophilic nanosheets regulating Li+ flux for lithium metal batteries

Fe3N@N-doped Graphene As a Lithiophilic Interlayer for Highly Stable Lithium Metal Batteries

A Bifunctional Carbon-LiNO3 Composite Interlayer for Stable Lithium Metal Powder Electrodes as High Energy Density Anode Material in Lithium Batteries

Nitrogen-Deficient Graphitic Carbon Nitride with Enhanced Performance for Lithium Ion Battery Anodes.

Highly Efficient Interface Modification between Poly(Propylene Carbonate)-Based Solid Electrolytes and a Lithium Anode by Facile Graphite Coating

Artificially regulated interphase on natural graphite realizes rapid charge and durable high-temperature cycling of Li-ion batteries

Carbon Nanofiber Interlayer: a Highly Effective Strategy to Stabilize Silicon Anodes for Use in Lithium-Ion Batteries

Acid-base encapsulation prepared N/P co-doped carbon-coated natural graphite for high-performance lithium-ion batteries

Nafion as a facile binder additive stabilizes solid electrolyte interphase on graphite anode

3D Framework with Li3N‐Li2S solid electrolyte interphase and fast ion transfer channels for stabilized lithium metal anode

Edge Structure and Formation of a Solid Electrolyte Interphase Film in Amorphous Carbon-Coated Spheroidized Graphite

A 3D Framework with Li3N-Li2S Solid Electrolyte Interphase and Fast Ion Transfer Channels for a Stabilized Lithium-Metal Anode

A Biscuit-Like Separator Enabling High Performance Lithium Batteries by Continuous and Protected Releasing of NO3− in Carbonate Electrolyte

Porous nitrogen–doped carbon-coated nano-silicon/graphite ternary composites as high-rate stability anode for Li-ion batteries

Nitrogen-Doped Hollow Carbon Nanospheres for High-Performance Li-Ion Batteries.

Nitrogen-Doped Carbon-Coating Disproportionated SiO Materials As Long Cycling Stable Anode for Lithium Ion Batteries

Functional multilayer solid electrolyte films for lithium dendrite suppression

Nitrogen-Doped Carbon for Sodium-Ion Battery Anode by Self-Etching and Graphitization of Bimetallic MOF-Based Composite

Functionalized Boron Nitride Nanosheets/Graphene Interlayer for Fast and Long‐Life Lithium–Sulfur Batteries