Abstract:A simple technique was developed for the modification of cotton materials that is inexpensive, environmentally friendly, and very effective. Waste Cotton fabrics (WCFs) are loaded with propolis extract (PE) for Cu2+ removal. Then, Cu2+ underwent a pyrolysis process with modified cuttlebone (CB) at 900 °C for 5 h. The surface of the prepared materials was characterized using X-ray diffraction (XRD), scanning electron microscopy with energy-dispersive X-ray (SEM-EDX), Fourier transform infrared (FTIR), BET, particle sizes, thermogravimetric analysis (TGA) and zeta potential analysis. The Cu2+ metal ions from an aqueous solution were removed using WCFs/PE, and DLM was subsequently removed using pyro WCFs/PE/Cu/CB. The as-prepared NPs exhibited the face-centered cubic structure of WCFs/PE/Cu/CB with crystallite sizes ranging from 386.70 to 653.10 nm. FTIR spectra revealed that CB was present on the surface of the resulting WCFs/PE/Cu. SEM revealed the dispersion of a uniformly flower-like morphology over a large area. Sorption studies were performed based on parameters that included pH, dose, contact time, and initial concentration. The adsorption isotherm and the kinetic studies of the DLM adsorption process were applied at a pH of 5.0 and a temperature of 25 °C using several isotherms and kinetic models. The results revealed qmax (20.51 mg/g) with R2 = 0.97, the Langmuir isotherm that best matches the experimental data. Hence, the Langmuir isotherm suggests that it is the model that best describes sorption on homogenous surfaces or surface-supporting sites with various affinities. The correlation coefficient R2, χ2, adjusted correlation coefficient, and error functions like root mean square (RMSE), normalized root mean square error (NRMES), and mean absolute error (MAE) were used to evaluate the best-fit models to the experimental adsorption data. Moreover, cost estimation for the prepared adsorbent WCFs/PE/Cu showed that it costs approximately 3 USD/g, which is a cheap adsorbent compared to other similar adsorbents reported in the literature. The examined WCFs/PE have significant applicability potential for Cu2+-laden wastewater treatment due to their superior Cu2+ metal ions adsorption capability and reusability. The cytotoxicity and safety study showed that at higher concentrations, it resulted in much less cell viability. Additionally, the removal efficiency of Cu2+ metal ions from synthetic, realistic industrial wastewater using WCFs/PE reached up to 96.29 %, demonstrating good adsorption capability. Thus, there is a huge possibility of accomplishing this and performing well. This study paves the way for the reuse and valorization of selected adsorbents following circular economy principles. Two green metrics were applied, the Analytical Eco-scale and the Analytical GREEnness Calculator (AGREE).

Removal of Mo(VI), Pb(II), and Cu(II) from wastewater using electrospun cellulose acetate/chitosan biopolymer fibers

Preparation of Cotton-Based Fibrous Adsorbents for the Removal of Heavy Metal Ions.

In-situ immobilization of CuMOF on sodium alginate/chitosan/cellulose nanofibril composite hydrogel for fast and highly efficient removal of Pb2+ from aqueous solutions

Magnetic recyclable biosorbents based on cotton cellulose and chitosan for copper(ii) removal from polluted water

A novel chitosan/cellulose phosphonate composite hydrogel for ultrafast and efficient removal of Pb(II) and Cu(II) from wastewater

Chitosan Modified Diatomite Cross-Linked with Sodium Alginate and Polyethyleneimine Composite Gel Particles for Efficient Removal of Copper and Lead Ions

Selective recovery of copper from copper tailings and wastewater using chelating resins with bis-picolylamine functional groups

Green, ultrafine cellulose-based porous nanofibrous membranes for efficient heavy metal removal through incorporation of chitosan by various electrospinning ways

Synthesis of cellulose cotton-based UiO-66 MOFs for the removal of rhodamine B and Pb(II) metal ions from contaminated wastewater

Consecutive high-performance removal of Cu2+ metal ions and Deltamethrin using multifunctional pyrolysis cuttlebone/cotton fabric nanocomposite

Efficient removal of copper ions and organic dyes using chitosan, pectin, and magnetic hydrogel composites: Structural characterization and adsorption mechanisms

A Novel Adsorbent of Core-Shell Construction of Chitosan-Cellulose Magnetic Carbon Foam: Synthesis, Characterization and Application to Remove Copper in Wastewater

The green, ultrafine cellulose-based porous nanofibrous membranes for efficient heavy metal ion removal through incorporation of chitosan by various electrospinning ways

Removal of copper ions by cellulose nanocrystal-based hydrogel and reduced adsorbents for its catalytic properties

Design of amphoteric MOFs-cellulose based composite for wastewater remediation: Adsorption and catalysis

Carboxymethyl Inulin Modified Chitosan Composites for Cu (II) Removal in Aqueous Solution: Synthesis, Influencing Factors and Adsorption Mechanism

Fabrication of Sustainable Sodium Alginate/Polyethyleneimine/Polyvinyl Alcohol Multilayer Composite Electrospun Nanofiber Membrane for Efficient Cu2+ Removal

All-biomass cellulose/casein adsorbent fabricated via the "green solvent system" of ionic liquid for the efficient removal of Cu(II), Cd(II) and Pb(II)

Modeling of Hexavalent Chromium Removal with Hydrophobically Modified Cellulose Nanofibers

The Development and Characterization of a Cotton–Chitosan Composite for Lead Removal from Water

A Millimeter-Sized Negatively Charged Polymer Embedded with Molybdenum Disulfide Nanosheets for Efficient Removal of Pb(II) from Aqueous Solution