Abstract:Recently, the polymer solar cells (PSCs) based on the PM6 and small molecular acceptor (SMA) Y6 have attracted considerable attention in this community for their outstanding photovoltaic performance. As well known, the molecular weight of polymer has dramatic impact on the blend morphology and photovoltaic performance in the polymer solar cells, especially for those polymers with temperature‐dependent aggregation (TDA) behavior. In this work, a series of PM6 polymers with different weight‐average molecular weights (Mw= 41, 67, 74, 84 and 114 kDa) were synthesized, and the effects of the Mw on the morphology and photovoltaic performance were systematically investigated. Notably, tuning the molecular weight induces dramatic influences on the aggregation behaviors of the polymers and their corresponding blend morphology, which were explored by the temperature‐dependent UV‐vis absorptions (TD‐Abs), grazing incidence wide‐angle X‐ray scattering (GIWAXS) and resonant soft X‐ray scattering(R‐SoXS) measurements. Increasing Mw promoted the strong face‐on molecular packing and reduced the blend film domain sizes for enhanced donor‐acceptor interfacial areas, resulting in increased short‐circuit current densities (Jsc) and fill factor (FF). However, polymer donor with high Mw value processed stronger tendency of forming excessive pure donor aggregate, which hampered forming the intermixed phase for efficient charge transport, resulting in the inferior FF. Therefore, the optimized OSCs based on PM6 with moderate molecular weight (Mw=74 kDa) and Y6 exhibited suitable size and purity of the domains, facilitating well‐balanced charge transport, reducing trap‐assisted recombination and leading to significant enhancement of photovoltaic performance with the optimal PCE of 17.1%. This work indicates that proper and precisely tuning the molecular weight of polymer donor is critical to enhance the photovoltaic performance in PSCs.This article is protected by copyright. All rights reserved.

Correlating Aggregation Ability of Polymer Donors with Film Formation Kinetics for Organic Solar Cells with Improved Efficiency and Processability

Superior Aggregation, Morphology and Photovoltaic Performance Enabled by Fine Tuning of Fused Electron-Deficient Units in Polymer Donors

MORPHOLOGIES AND PERFORMANCE OF ORGANIC SOLAR CELLS USING LOW POLYMERIZATION DEGREE ALTERNATING COPOLYMER

A Polycrystalline Polymer Donor As Pre-Aggregate Toward Ordered Molecular Aggregation for 19.3% Efficiency Binary Organic Solar Cells.

Linear Regulating of Polymer Acceptor Aggregation with Short Alkyl Chain Units Enhances All-Polymer Solar Cells' Efficiency

High‐Performance Terpolymers with Well‐Defined Structures Facilitate PCE over 19% for Polymer Solar Cells

Tunable Donor Aggregation Dominance in a Ternary Matrix of All-Polymer Blends with Improved Efficiency and Stability

Tunable Donor Aggregation Dominance in Ternary Matrix of All‐polymer Blends with Improved Efficiency And Stability

Enhancing the Performance of Polymer Solar Cells by Using Donor Polymers Carrying Discretely Distributed Side Chains.

Effect of Alkyl Side Chains of Polymer Donors on Photovoltaic Performance of All-Polymer Solar Cells

A Random Terpolymer Donor with Similar Monomers Enables 18.28% Efficiency Binary Organic Solar Cells with Well Polymer Batch Reproducibility

Aggregation Tuning with Heavily Fluorinated Donor Polymer for Efficient Organic Solar Cells.

Optimizing Active Layer Morphology of Organic Solar Cells by Constructing Random Copolymers with Simple Third Units.

Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64% Efficiency All Polymer Solar Cells

Preparation of Efficient Organic Solar Cells Based on Terpolymer Donors Via a Monomer-Ratio Insensitive Side-Chain Hybridization Strategy

Tuning Aggregation Behavior of Polymer Donor via Molecular‐Weight Control for Achieving 17.1% Efficiency Inverted Polymer Solar Cells

A Facile Method to Fine-Tune Polymer Aggregation Properties and Blend Morphology of Polymer Solar Cells Using Donor Polymers with Randomly Distributed Alkyl Chains

Terpolymer Containing a meta-Octyloxy-phenyl-Modified Dithieno[3,2- f:2',3'- h]quinoxaline Unit Enabling Efficient Organic Solar Cells

Optimized Molecular Aggregation Via Incorporating Fluorinated Unit in the Polymer Donor for 17.3% Efficiency Organic Solar Cells

Optimizing the Film Formation of High Crystalline Donors for Efficient Organic Solar Cells

Regulating the Morphology of Fluorinated Non-Fullerene Acceptor and Polymer Donor Via Binary Solvent Mixture for High Efficiency Polymer Solar Cells