Ultrasound in the Intrauterine Diagnosis and Treatment of Fetal Abnormalities

R. Petres,F. Redwine

DOI: https://doi.org/10.1097/00003081-198212000-00011

1982-12-01

Abstract:

What problem does this paper attempt to address?

Cross talks between the immune and lymphatic endothelial cells regulate inflammatory lymph node lymphangiogenesis: defining a new therapeutic approach

Sonia Elhadad

DOI: https://doi.org/10.1186/2051-1426-1-S1-P184

2013-11-01

Abstract:
A Miniature Potentiometric Sensor for Dopamine Determination in Vitro

Cheng He,Guang Li,You Wang,Wujie Zhou

DOI: https://doi.org/10.1088/1361-6501/abbfed

IF: 2.398

2021-01-01

Measurement Science and Technology

Abstract:Electrochemical sensors can be used to detect neurotransmitters. A miniature potentiometric all-solid-state coated wire dopamine sensor was investigated in this work. Conducting polymer poly (3,4- ethylenedioxythiophene) doped with poly (styrenesulfonate) as the solid contact was electropolymerized on one end of a gold wire (diameter 0.25 mm). The conducting polymer was covered with a dopamine-selective membrane containing 12-crown-4-tetraphenylborate as a neutral carrier, 2-nitrophenyloctyl ether as a plasticizer and poly (vinyl chloride) as the membrane matrix. The dopamine sensor covered a wide linear range from 10(-5) M to 10(-1) M with a slope of 53.85 +/- 0.93 mV/decade, while the detection limit was 5.80 +/- 0.31 mu M. The other characteristics of the dopamine sensor were also evaluated. The experimental results showed that the sensor operated properly within the pH range of 5.5-7.5 and displayed good selectivity, fast dynamic response, high reproducibility and long stability. In addition, the dopamine sensor was successfully applied for the detection of dopamine in artificial cerebrospinal fluid by using the standard addition method, indicating that this sensor is promising for applications in dopamine determination in neuroscientific research.
Monitoring the Electrochemical Responses of Neurotransmitters Through Localized Surface Plasmon Resonance Using Nanohole Array.

Nantao Li,Yanli Lu,Shuang Li,Qian Zhang,Jiajia Wu,Jing Jiang,Gang Logan Liu,Qingjun Liu

DOI: https://doi.org/10.1016/j.bios.2016.08.105

IF: 12.545

2016-01-01

Biosensors and Bioelectronics

Abstract:In this study, a novel spectroelectrochemical method was proposed for neurotransmitters detection. The central sensing device was a hybrid structure of nanohole array and gold nanoparticles, which demonstrated good conductivity and high localized surface plasmon resonance (LSPR) sensitivity. By utilizing such specially-designed nanoplasmonic sensor as working electrode, both electrical and spectral responses on the surface of the sensor could be simultaneously detected during the electrochemical process. Cyclic voltammetry was implemented to activate the oxidation and recovery of dopamine and serotonin, while transmission spectrum measurement was carried out to synchronously record to LSPR responses of the nanoplasmonic sensor. Coupling with electrochemistry, LSPR results indicated good integrity and linearity, along with promising accuracy in qualitative and quantitative detection even for mixed solution and in brain tissue homogenates. Also, the detection results of other negatively-charged neurotransmitters like acetylcholine demonstrated the selectivity of our detection method for transmitters with positive charge. When compared with traditional electrochemical signals, LSPR signals provided better signal-to-noise ratio and lower detection limits, along with immunity against interference factors like ascorbic acid. Taking the advantages of such robustness, the coupled detection method was proved to be a promising platform for point-of-care testing for neurotransmitters.
Evaluation of In Vitro Serotonin-Induced Electrochemical Fouling Performance of Boron Doped Diamond Microelectrode Using Fast-Scan Cyclic Voltammetry

Mason L. Perillo,Bhavna Gupta,James R. Siegenthaler,Isabelle E. Christensen,Brandon Kepros,Abu Mitul,Ming Han,Robert Rechenberg,Michael F. Becker,Wen Li,Erin K. Purcell

DOI: https://doi.org/10.3390/bios14070352

2024-07-20

Biosensors

Abstract:Fast-scan cyclic voltammetry (FSCV) is an electrochemical sensing technique that can be used for neurochemical sensing with high spatiotemporal resolution. Carbon fiber microelectrodes (CFMEs) are traditionally used as FSCV sensors. However, CFMEs are prone to electrochemical fouling caused by oxidative byproducts of repeated serotonin (5-HT) exposure, which makes them less suitable as chronic 5-HT sensors. Our team is developing a boron-doped diamond microelectrode (BDDME) that has previously been shown to be relatively resistant to fouling caused by protein adsorption (biofouling). We sought to determine if this BDDME exhibits resistance to electrochemical fouling, which we explored on electrodes fabricated with either femtosecond laser cutting or physical cleaving. We recorded the oxidation current response after 25 repeated injections of 5-HT in a flow-injection cell and compared the current drop from the first with the last injection. The 5-HT responses were compared with dopamine (DA), a neurochemical that is known to produce minimal fouling oxidative byproducts and has a stable repeated response. Physical cleaving of the BDDME yielded a reduction in fouling due to 5-HT compared with the CFME and the femtosecond laser cut BDDME. However, the femtosecond laser cut BDDME exhibited a large increase in sensitivity over the cleaved BDDME. An extended stability analysis was conducted for all device types following 5-HT fouling tests. This analysis demonstrated an improvement in the long-term stability of boron-doped diamond over CFMEs, as well as a diminishing sensitivity of the laser-cut BDDME over time. This work reports the electrochemical fouling performance of the BDDME when it is repeatedly exposed to DA or 5-HT, which informs the development of a chronic, diamond-based electrochemical sensor for long-term neurotransmitter measurements in vivo.

chemistry, analytical,nanoscience & nanotechnology,instruments & instrumentation
Nucleotide sequence of rabbit eIF-4E cDNA.

W. Rychlik,R. Rhoads

DOI: https://doi.org/10.1093/NAR/20.23.6415

IF: 14.9

1992-12-11

Nucleic Acids Research

Abstract:Eukaryotes. CRCPress, Boca Raton, FL, pp. 109-148.3. Thach,R.E. (1992) Cell 68, 177-180.4. Rychlik,W., Domier,L.L., Gardner,P.R., Hellmann,G.M. andRhoads,R.E.(1987) Proc. Natl. Acad. Sci. USA84, 945-949.5. Altmann,M., Handschin,C. and Trachsel,H. (1987) Mol. Cell. Biol. 7,998-1003.6. McCubbin,W.D., Edery,I., Altmann,M., Sonenberg,N. and Kay,C.M.(1988)J. Biol. Chem. 263, 17663-17671.
Antifouling nanoporous diamond membrane for enhanced detection of dopamine in human serum

Haichao Li,Jun Cao,Qiuping Wei,Li Ma,Kechao Zhou,Zhiming Yu,Sichao Zeng,Ruitong Zhu,Wanlin Yang,Cheng-Te Lin,Lingcong Meng

DOI: https://doi.org/10.1007/s10853-020-05344-5

IF: 4.5

2020-10-01

Journal of Materials Science

Abstract:In vivo tracking or in vitro real sample analysis by electrochemistry is one of the most straight and useful methods in biosensor field. However, surface biofouling of electrodes by non-specific protein adsorption is inevitable and usually leads to a decrease in sensitivity. Here, we developed a Nafion-coated porous boron-doped diamond (NAF/pBDD) electrode with hydrophobic nanostructures to minimize the biofouling effect and selectively detect dopamine (DA). Larger active area was obtained by this procedure compared to a bare diamond electrode. The as-prepared electrode shows excellent antifouling property and enrichment capacity toward selective detection of dopamine (DA). The low background current of the BDD electrode and the enhanced signals enables a lower detection limit, 42 nmol L−1, and a wider linear range, 0.1–110 μmol L−1, for determination of DA in human serum. Additionally, the facile modified electrode demonstrated renewable property and long-term stability due to the fact that the antifouling nanostructures belong to its own.

materials science, multidisciplinary
A novel modification to boron-doped diamond electrode for enhanced, selective detection of dopamine in human serum

Haichao Li,Kechao Zhou,Jun Cao,Qiuping Wei,Cheng-Te Lin,Sharel E. Pei,Li Ma,Naixiu Hu,Yaohua Guo,Zejun Deng,Zhiming Yu,Sichao Zeng,Wanlin Yang,Lingcong Meng

DOI: https://doi.org/10.1016/j.carbon.2020.08.019

IF: 10.9

2021-01-01

Carbon

Abstract:In this work, we proposed a novel modification technique to immobilize nanoparticles by the nanopores on a boron-doped diamond surface, preventing the aggregation of nanoparticles physically and improving the stability of nanoparticles layer by the anchoring effect. All the exposed surfaces of a bare boron-doped diamond were etched into nanoporous form and larger electrochemically active surface area was obtained on the porous boron-doped diamond electrode. The carbon black nanoparticles modified porous boron-doped diamond electrode showed good selectivity to separate the oxidation potential of three molecules, but led to an extra increase in the peak current of dopamine (DA). The carbon black/Nafion modified porous diamond electrode effectively suppress the oxidation current of ascorbic acid (AA), enhancing the sensitivity of DA. The dual layer treatment enables a wide linear range, 0.1-100 μM and a low limit of detection, 54 nM for DA detection, which is almost unaffected by the excess AA and uric acid (UA). At last, real sample tests of the carbon black/Nafion modified porous diamond electrode was validated by applying to the detection of DA in human serum and dopamine hydrochloride injection, which were found to be promising at our preliminary experiments. Additionally, the fabricated carbon black/Nafion modified porous diamond electrode also demonstrated good stability and long-term functionality.

materials science, multidisciplinary,chemistry, physical
Sensitive detection of dopamine using a platinum microelectrode modified by reduced graphene oxide and gold nanoparticles

Xing Chen,Jing Chen,Hao Dong,Qiwen Yu,Shaomin Zhang,Hang Chen

DOI: https://doi.org/10.1016/j.jelechem.2019.113244

IF: 4.598

2019-01-01

Journal of Electroanalytical Chemistry

Abstract:Platinum wire microelectrodes generally exhibited properties of low sensitivity but are easily contaminated where it comes to dopamine detection. In this paper, a platinum wire modified with gold nanoparticles (AuNPs) and reduced graphene oxide (rGO) was used to electrochemically detect dopamine in vivo. Electrochemical performances of microelectrodes (before and after surface modification) were investigated by impedance spectroscopy and cyclic voltammetry. The results showed that AuNPs/rGO composites significantly increase the electrode surface area and improve the electrocatalytic property of platinum wires. The modified electrodes exhibited excellent sensitivity for dopamine detection (LOD=16.57nM), as well as ascendant selectivity (simultaneous detection of ascorbic acid, dopamine, and uric acid), reproducibility (R.S.D.=3.98%), and stability (≫100 repetitive potential sweeps, 1-week lifespan). In vivo experiments showed that the proposed AuNPs/rGO electrode was also capable of detecting dopamine in complex physiological environments, particularly in the striatum of anesthetized rats. Hence, the proposed electrodes provided a potential application in in vivo multiplexing neurotransmitter detection in further research.
Real-time selective detection of dopamine and serotonin at nanomolar concentration from complex in vitro systems

Samuel Rantataro,Ilmari Parkkinen,Mikko Airavaara,Tomi Laurila

DOI: https://doi.org/10.1016/j.bios.2023.115579

2023-12-01

Abstract:Electrochemical sensors provide means for real-time monitoring of neurotransmitter release events, which is a relatively easy process in simple electrolytes. However, this does not apply to in vitro environments. In cell culture media, competitively adsorbing molecules are present at concentrations up to 350 000-fold excess compared to the neurotransmitter-of-interest. Because detection of dopamine and serotonin requires direct adsorption of the analyte to electrode surface, a significant loss of sensitivity occurs when recording is performed in the in vitro environment. Despite these challenges, our single-walled carbon nanotube (SWCNT) sensor was capable of selectively measuring dopamine and serotonin from cell culture medium at nanomolar concentration in real-time. A primary midbrain culture was used to prove excellent biocompatibility of our SWCNT electrodes, which is a necessity for brain-on-a-chip models. Most importantly, our sensor was able to electrochemically record spontaneous transient activity from dopaminergic cell culture without altering the culture conditions, which has not been possible earlier. Drug discovery and development requires high-throughput screening of in vitro models, being hindered by the challenges in non-invasive characterization of complex neuronal models such as organoids. Our neurotransmitter sensors could be used for real-time monitoring of complex neuronal models, providing an alternative tool for their characterization non-invasively.
Oligo-layer Graphene Stabilized Fully Exposed Fe-sites for Ultra-Sensitivity Electrochemical Detection of Dopamine

Zejun Sun,Shuang Sun,Xue Jiang,Yongjian Ai,Wenjuan Xu,Liping Xie,Hong-bin Sun,Qionglin Liang

DOI: https://doi.org/10.1016/j.bios.2022.114367

IF: 12.545

2022-01-01

Biosensors and Bioelectronics

Abstract:Neurotransmitter dopamine (DA) has been implicated in a variety of physiological and pathological processes, realizing its low detection limit and high sensitivity analysis is of great significance for early disease diagnosis. Herein, we propose a simple pyrolysis approach for dispersing Fe-sites onto the N-doped graphene support (denoted as Fe/N-GR) to construct an electrochemical biosensor for DA detection. The fully exposed Fe-sites guaranteed the well-defined active center for electrochemical oxidation of DA. The Fe/N-GR electrochemical biosensor achieves an ultra-low detection limit for DA of 27 pM with a linear range of 50 pM-15 nM. Specifically, the Fe/N-GR electrochemical biosensor exhibits favorable sensitivity and enzyme-level molecular identification ability in the selective detection of DA versus other typical redox-active interferents. What's more, the detection of dopamine in real human serum samples verifies the applicability of the developed sensor. Our results demonstrate a promising means of using fully exposed metal-site subnanometric catalysts for electrochemical sensing applications.
Electrochemical Biosensing of Dopamine Neurotransmitter: A Review

Sophie Lakard,Ileana-Alexandra Pavel,Boris Lakard

DOI: https://doi.org/10.3390/bios11060179

2021-06-03

Biosensors

Abstract:Neurotransmitters are biochemical molecules that transmit a signal from a neuron across the synapse to a target cell, thus being essential to the function of the central and peripheral nervous system. Dopamine is one of the most important catecholamine neurotransmitters since it is involved in many functions of the human central nervous system, including motor control, reward, or reinforcement. It is of utmost importance to quantify the amount of dopamine since abnormal levels can cause a variety of medical and behavioral problems. For instance, Parkinson’s disease is partially caused by the death of dopamine-secreting neurons. To date, various methods have been developed to measure dopamine levels, and electrochemical biosensing seems to be the most viable due to its robustness, selectivity, sensitivity, and the possibility to achieve real-time measurements. Even if the electrochemical detection is not facile due to the presence of electroactive interfering species with similar redox potentials in real biological samples, numerous strategies have been employed to resolve this issue. The objective of this paper is to review the materials (metals and metal oxides, carbon materials, polymers) that are frequently used for the electrochemical biosensing of dopamine and point out their respective advantages and drawbacks. Different types of dopamine biosensors, including (micro)electrodes, biosensing platforms, or field-effect transistors, are also described.
Chemical Modification of Boron-Doped Diamond Electrodes for Applications to Biosensors and Biosensing

Jana Svítková,Teodora Ignat,Ľubomír Švorc,Ján Labuda,Jiří Barek

DOI: https://doi.org/10.1080/10408347.2015.1082125

2015-09-04

Critical Reviews in Analytical Chemistry

Abstract:Boron-doped diamond (BDD) is a prospective electrode material that possesses many exceptional properties including wide potential window, low noise, low and stable background current, chemical and mechanical stability, good biocompatibility, and last but not least exceptional resistance to passivation. These characteristics extend its usability in various areas of electrochemistry as evidenced by increasing number of published articles over the past two decades. The idea of chemically modifying BDD electrodes with molecular species attached to the surface for the purpose of creating a rational design has found promising applications in the past few years. BDD electrodes have appeared to be excellent substrate materials for various chemical modifications and subsequent application to biosensors and biosensing. Hence, this article presents modification strategies that have extended applications of BDD electrodes in electroanalytical chemistry. Different methods and steps of surface modification of this electrode material for biosensing and construction of biosensors are discussed.

chemistry, analytical
Novel Electrochemical Sensor Application for Dopamine and Preparation of N-rGO Micro-regionally Constrained WS2 Nanocomposite

Ning Dai,Guohua Shi,Tingting Li,Nan Liu,Zhongkai Xu,Zhe Chen,Jiefang Sun,Ruisong Guo,Chunming Zheng,xiaohong Sun

DOI: https://doi.org/10.1149/1945-7111/acabed

IF: 3.9

2022-12-17

Journal of The Electrochemical Society

Abstract:Dopamine is an important neurotransmitter for organisms and affects their function, so monitoring and detecting dopamine levels is essential. Sensitivity and selectivity of electrochemical sensors for the detection of dopamine usually relies on hybrid nanocomposites. In this context, we designed a micro-regionally restricted hybrid nanocomposite by modulating the micro-nano structure. Using functional groups on nitrogen-doped reduced graphene oxide (N-rGO) to restrict the random growth of tungsten disulfide nanosheets, we obtained a 2D layered material with bidirectional structural support to achieve high specific surface and high activity for application in robust and novel dopamine electrochemical sensors. A facile electrochemical sensor for dopamine detection was fabricated by modifying a screen-printed carbon electrode with the nanocomposite. The sensor exhibits excellent performance of dopamine detection in the wide range of 1 μmol/L100 μmol/L with a detection limit of 0.2 μmol/L and a high sensitivity of 0.56 μA/μmol/L. The optimized sensor shows a good selectivity, satisfactory long-term stability and reproducibility towards DA and a separation of peak potential of 142 mV with uric acid. In addition, the prepared sensor provides favorable recovery in human serum and artificial cerebrospinal solution (aSCF), indicating great potentials in electrochemical detection and biological sensing applications.

electrochemistry,materials science, coatings & films
Low-interference and sensitive electrochemical detection of glucose and lactate using boron-doped diamond electrode and electron mediator menadione

Nakyeong Yoon,Youngjin Jung,Gyeongho Kim,Jungwook Kwon,Haesik Yang

DOI: https://doi.org/10.1007/s44211-023-00497-0

IF: 1.967

2024-01-22

Analytical Sciences

Abstract:To minimize background interference in electrochemical enzymatic biosensors employing electron mediators, it is essential for the electrochemical oxidation of electroactive interfering species (ISs), such as ascorbic acid (AA), to proceed slowly, and for the redox reactions between electron mediators and ISs to occur at a low rate. In this study, we introduce a novel combination of a working electrode and an electron mediator that effectively mitigates interference effects. Compared to commonly used electrodes such as Au, glassy carbon, and indium tin oxide (ITO), boron-doped diamond (BDD) electrodes demonstrate significantly lower anodic current (i.e., lower background levels) in the presence of AA. Additionally, menadione (MD) exhibits notably slower reactivity with AA compared to other electron mediators such as Ru(NH 3 ) 6 3+ , 4-amino-1-naphthol, and 1,4-naphthoquinone, primarily due to the lower formal potential of MD compared to AA. This synergistic combination of BDD electrode and MD is effectively applied in three biosensors: (i) glucose detection using electrochemical-enzymatic (EN) redox cycling, (ii) glucose detection using electrochemical-enzymatic-enzymatic (ENN) redox cycling, and (iii) lactate detection using ENN redox cycling. Our developed approach significantly outperforms the combination of ITO electrode and MD in minimizing IS interference. Glucose in artificial serum can be detected with detection limits of ~ 20 μM and ~ 3 μM in EN and ENN redox cycling, respectively. Furthermore, lactate in human serum can be detected with a detection limit of ~ 30 μM. This study demonstrates sensitive glucose and lactate detection with minimal interference, eliminating the need for (bio)chemical agents to remove interfering species.

chemistry, analytical
MPCVD-Grown Nanodiamond Microelectrodes with Oxygen Plasma Activation for Neurochemical Applications

Zijun Shao,Leslie Wilson,Yuanyu Chang,B Jill Venton

DOI: https://doi.org/10.1021/acssensors.2c01803

2022-10-28

Abstract:Nanodiamonds (NDs) are a carbon nanomaterial that has a diamond core with heteroatoms and defects at the surface. The large surface area, defect sites, and functional groups on NDs make them a promising material for electrochemical sensing. Previously, we dip-coated ND onto carbon-fiber microelectrodes (CFMEs) and found increases in sensitivity, but the coating was sparse. Here, we directly grew thin films of ND on niobium wires using microwave plasma chemical vapor deposition (MP-CVD) to provide full surface coverage. ND microelectrodes show a reliable performance in neurotransmitter detection with good antifouling properties. To improve sensitivity, we oxygen plasma etched ND films to activate the surface and intentionally add defects and oxygen surface functional groups. For fast-scan cyclic voltammetry detection of dopamine, oxygen plasma-etching increases the sensitivity from 21 nA/μM to 90 nA/μM after treatment. Fouling was tested by repeated injections of serotonin or tyramine, and both ND and plasma oxidized nanodiamond (NDO) microelectrodes maintain their currents better compared to CFMEs and therefore are more antifouling. A biofouling test in brain slices shows that ND microelectrodes barely have any current drop, while the more hydrophilic NDO microelectrodes decrease more, but still not as much as CFMEs. Overall, grown ND microelectrodes are promising in neurotransmitter detection with excellent fouling resistance, whereas oxygen plasma etching slightly lowers the fouling resistance but dramatically increases sensitivity.
Dopamine Measurement Using Engineered CNT–CQD–Polymer Coatings on Pt Microelectrodes

Mahdieh Darroudi,Kevin A. White,Matthew A. Crocker,Brian N. Kim

DOI: https://doi.org/10.3390/s24061893

IF: 3.9

2024-03-15

Sensors

Abstract:This study aims to develop a microelectrode array-based neural probe that can record dopamine activity with high stability and sensitivity. To mimic the high stability of the gold standard method (carbon fiber electrodes), the microfabricated platinum microelectrode is coated with carbon-based nanomaterials. Carboxyl-functionalized multi-walled carbon nanotubes (COOH-MWCNTs) and carbon quantum dots (CQDs) were selected for this purpose, while a conductive polymer like poly (3-4-ethylene dioxythiophene) (PEDOT) or polypyrrole (PPy) serves as a stable interface between the platinum of the electrode and the carbon-based nanomaterials through a co-electrodeposition process. Based on our comparison between different conducting polymers and the addition of CQD, the CNT–CQD–PPy modified microelectrode outperforms its counterparts: CNT–CQD–PEDOT, CNT–PPy, CNT–PEDOT, and bare Pt microelectrode. The CNT–CQD–PPy modified microelectrode has a higher conductivity, stability, and sensitivity while achieving a remarkable limit of detection (LOD) of 35.20 ± 0.77 nM. Using fast-scan cyclic voltammetry (FSCV), these modified electrodes successfully measured dopamine's redox peaks while exhibiting consistent and reliable responses over extensive use. This electrode modification not only paves the way for real-time, precise dopamine sensing using microfabricated electrodes but also offers a novel electrochemical sensor for in vivo studies of neural network dynamics and neurological disorders.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
High-sensitivity, selective determination of dopamine using bimetallic nanoparticles modified boron-doped diamond electrode with anodic polarization treatment

Haichao Li,Yaohua Guo,Sichao Zeng,Qiuping Wei,P. E. Sharel,Ruitong Zhu,Jun Cao,Li Ma,KeChao Zhou,Lingcong Meng

DOI: https://doi.org/10.1007/s10853-020-05577-4

IF: 4.5

2020-11-24

Journal of Materials Science

Abstract:Selective detection of dopamine is still a challenge due to the strong interference from ascorbic acid (AA). A hybrid dopamine electrochemical sensor was fabricated by boron-doped diamond (BDD) film co-modified with gold nanoparticles and graphite-coated nickel nanoparticles (Au-C@Ni/BDD). Highly sensitive and selective detection toward dopamine was achieved by multiple electrochemical anodic polarization treatment (EAPT) with relatively mild voltage (+ 1.6 V vs. Ag/AgCl) on Au-C@Ni/BDD electrode. Specifically, the oxidation peak separation between ascorbic acid and dopamine reached 166 mV, and the limit of detection of dopamine was as low as 0.015 μM in a linear concentration range of 0.05–100 μM with the sensitivity up to 1.99 μA μM−1 cm−2 even in the presence of interference of high-level AA. These could be ascribed to the electrocatalytically active sites and functional oxygen-containing groups of the hybrid electrodes produced by the EAPT and the excellent catalytical activity of gold nanoparticles.

materials science, multidisciplinary
Effect of boron doping levels on the microstructure and characteristics of high-quality boron-doped diamond electrodes prepared by MPCVD

Yanpeng Gong,Wenru Jia,Bing Zhou,Ke Zheng,Dandan Ma,Zhibo Li,Jie Gao,Yong Ma,Hongjun Hei,Shengwang Yu,Yanpeng Xue,Yucheng Wu

DOI: https://doi.org/10.1016/j.diamond.2023.110377

IF: 3.806

2023-09-17

Diamond and Related Materials

Abstract:In order to fully understand the relationship between boron doping level and material characteristics, a series of high-quality boron-doped diamond (BDD) electrodes with different boron doping levels (B/C ratios = 1000–5000 ppm) were prepared on a silicon substrate using a self-designed microwave plasma chemical vapor deposition (MPCVD) reactor in this study. The relationship between surface morphology, structural composition, chemical bonding state, electrical conductivity and electrochemical properties of BDD electrodes was investigated systematically. With the increase of boron doping level, the grain size of the BDD electrode tends to decrease, the crystal orientation tends to be dominated by (111) orientation, the conductivity increases sharply and then gradually stabilizes, while the width of the potential window tends to decrease (4.39 V to 3.95 V from 1000 ppm to 5000 ppm), and the reversibility and stability of the electrode improves significantly. In addition, such high-quality BDD electrodes also exhibit a higher sensitivity (0.1176 μAμM −1 cm −2 ) and lower limit of detection (0.276 μM) in the detection of dopamine. The boron doping level in BDD electrodes plays a prominent role in material characteristics such as surface morphology, structural composition, chemical bonding state, electrical conductivity and electrochemical properties. Despite the challenging synthesis of pure sp 3 carbon materials at high boron doping levels, the BDD electrodes prepared in this study exhibit high quality without sp 2 defects even with high boron doping levels, and possess extremely low resistivity (~10 −3 Ω·cm) and a wide electrochemical potential window (~4 V), which has not been achieved in other previous research works and offer great potential in the electrochemical applications of BDD electrodes.

materials science, multidisciplinary,physics, applied, condensed matter, coatings & films
Influence of Boron Doped Level on the Electrochemical Behavior of Boron Doped Diamond Electrodes and Uric Acid Detection

Peng Yu,Jiawei Zhang,Tong Zheng,Ting Wang

DOI: https://doi.org/10.1016/j.colsurfa.2016.01.031

IF: 5.518

2016-01-01

Colloids and Surfaces A Physicochemical and Engineering Aspects

Abstract:The boron doped diamond (BDD) electrodes were effective biosensors for the trace detection of organic pollutants in aqueous solution. BDD electrodes with different boron doped levels will display distinct binding energy and carrier density from the perspective of semiconductor, thus significantly impact the current and oxidation peak potential, and further influence detection performance of hazardous substances. In this study, BDDs with different boron doped levels were prepared by hot filament chemical vapor deposition method, followed by characterization of morphology and electrochemical behavior through various methods. Carrier concentrations, which were highly relevant to the charge transfer in diamond lattice, and flat-bandpotentials that can reflect the oxidation peak potential, were calculated through Mott-Schottky plots. Uric acid was chosen as typical matter for trace detection. As results, the continuous films without cracks were formed for all BDDs by SEM detection, and the size of diamond grain decreased with the increase of boron doped level. Moreover, the carrier concentration enhanced with the increasing boron doped level, thus resulted in the augment of current density. While the Fermi levels calculated from flat band potentials, decreased with the increase of boron doped level, suggesting the decrease of oxidation peak potential. These were in accordance with the results from cyclic voltammetry. Differential pulse voltammetry proved that BDD with higher boron concentration presented higher sensibility to uric acid, lower detection limit and wider linear range, which can be attributed to stronger current response. (C) 2016 Elsevier B.V. All rights reserved.
Mechanosynthesis of pharmaceutically relevant sulfonyl-(thio)ureas.

Davin Tan,Vjekoslav Štrukil,C. Mottillo,T. Friščić

DOI: https://doi.org/10.1039/c3cc47905f

IF: 4.9

2014-04-22

Chemical Communications

Abstract:We demonstrate the first application of mechanochemistry to conduct the synthesis of sulfonyl-(thio)ureas, including known anti-diabetic drugs tolbutamide, chlorpropamide and glibenclamide, in good to excellent isolated yields by either stoichiometric base-assisted or copper-catalysed coupling of sulfonamides and iso(thio)cyanates.

Ultrasound in the Intrauterine Diagnosis and Treatment of Fetal Abnormalities

Cross talks between the immune and lymphatic endothelial cells regulate inflammatory lymph node lymphangiogenesis: defining a new therapeutic approach

A Miniature Potentiometric Sensor for Dopamine Determination in Vitro

Monitoring the Electrochemical Responses of Neurotransmitters Through Localized Surface Plasmon Resonance Using Nanohole Array.

Evaluation of In Vitro Serotonin-Induced Electrochemical Fouling Performance of Boron Doped Diamond Microelectrode Using Fast-Scan Cyclic Voltammetry

Nucleotide sequence of rabbit eIF-4E cDNA.

Antifouling nanoporous diamond membrane for enhanced detection of dopamine in human serum

A novel modification to boron-doped diamond electrode for enhanced, selective detection of dopamine in human serum

Sensitive detection of dopamine using a platinum microelectrode modified by reduced graphene oxide and gold nanoparticles

Real-time selective detection of dopamine and serotonin at nanomolar concentration from complex in vitro systems

Oligo-layer Graphene Stabilized Fully Exposed Fe-sites for Ultra-Sensitivity Electrochemical Detection of Dopamine

Electrochemical Biosensing of Dopamine Neurotransmitter: A Review

Chemical Modification of Boron-Doped Diamond Electrodes for Applications to Biosensors and Biosensing

Novel Electrochemical Sensor Application for Dopamine and Preparation of N-rGO Micro-regionally Constrained WS2 Nanocomposite

Low-interference and sensitive electrochemical detection of glucose and lactate using boron-doped diamond electrode and electron mediator menadione

MPCVD-Grown Nanodiamond Microelectrodes with Oxygen Plasma Activation for Neurochemical Applications

Dopamine Measurement Using Engineered CNT–CQD–Polymer Coatings on Pt Microelectrodes

High-sensitivity, selective determination of dopamine using bimetallic nanoparticles modified boron-doped diamond electrode with anodic polarization treatment

Effect of boron doping levels on the microstructure and characteristics of high-quality boron-doped diamond electrodes prepared by MPCVD

Influence of Boron Doped Level on the Electrochemical Behavior of Boron Doped Diamond Electrodes and Uric Acid Detection

Mechanosynthesis of pharmaceutically relevant sulfonyl-(thio)ureas.