Abstract:Two fluorescent high‐performance polymers based on dicyanoarylamine luminogens were readily synthesized via polycondensation. Both polymers were soluble in several polar aprotic solvents and exhibited useful levels of thermal stability. The polymers were emissive in both solution and solid film states, thereby demonstrating the aggregation‐induced fluorescence changes. Introduction Fluorescent high‐performance polymers have been extensively used in designing optoelectronic devices due to their low cost, excellent thermal stability, high mechanical strength, low flammability, good chemical and radiation resistance, and good electronic properties. While conventional organic luminophores fluoresce strongly in dilute solutions, they suffer from undesirable aggregation‐caused quenching in concentrated solutions and in the solid state due to extensive π‐π stacking interactions and formation of delocalized excitons or excimers. This phenomenon leads to non‐radiative decay thus, decreased fluorescence emission of the material in the solid film state, which significantly limits their real‐world application as solid light‐emitting materials. Objectives To develop new high‐performance polymers with high photo luminescent efficiency, good processability, film‐forming properties, which could potentially be used in the fabrication of optoelectronic devices. Methods The preparation of the polyimide DiCN‐PI was carried out by a one‐step, high‐temperature solution imidization method. In this procedure, 1,2,4,5‐cyclohexanetetracarboxylic dianhydride and the diamine were polymerized in 1‐methyl‐2‐pyrrolidinone and γ‐butyrolactone co‐solvent at 180°C for 15 hours in the presence of isoquinoline as catalyst. On the other hand, polyamide DiCN‐PA was synthesized according to the direct phosphorylation polycondensation technique described by Yamazaki from diamine and trans‐1,4‐cyclohexanedicarboxylic acid using triphenyl phosphite and pyridine as condensing agents. Results and Discussion Both polymers were soluble in several polar aprotic solvents and exhibited useful levels of thermal stability. The polymers were emissive with PL emission bands around 555 (bluish‐green) and 498 (cyan) nm in dilute 1‐methyl‐2‐pyrrolidinone solutions for polyimide and polyamide, respectively. In the solid film state, the polymers emit light green and yellow colors, which simulate the PL behavior of their aggregated states, thereby demonstrating aggregation‐induced fluorescence changes. Conclusions These results indicate that the incorporation of bulky dicyanoarylamine moiety and alicyclic monomer units into the rigid polymer backbones effectively disrupted the planarity of the chain packing which resulted to the fluorescent high‐performance polymers with desired properties for potential optoelectronic applications.

Dicyanopyridine derivatives: One-pot preparation, ACQ-to-AIE transformation, light-conversion quality and photostability

Aza-Dicyclopenta[<i>a</i>,<i>g</i>]naphthalenes: Controllable Seesaw-like Emissive Behavior and Narrowband AIEgens

Twisted D–π–A Solid Emitters: Efficient Emission and High Contrast Mechanochromism

A facile design of azaanthracene derivatives: ACQ–AIE conversion and blue-shifted mechanofluorochromic emission

Dicarbazolyldicyanobenzenes as Thermally Activated Delayed Fluorescence Emitters: Effect of Substitution Position on Photoluminescent and Electroluminescent Properties

Substituent Effects on the Mechanochromic Behavior of Pyrene-Based AIEgens

Aggregation-Induced Fluorescence Emission Properties of Dicyanomethylene-1,4-Dihydropyridine Derivatives

Enabling DPP Derivatives to Show Multistate Emission and Developing the Multifunctional Materials by Rational Branching Effect

Transform ACQ Luminophores to AIEgens via Engineering the Variable C-C Bonds of o-Carboranes in Fluorescent Cores

Facile ACQ-to-AIE Transformation Via Diphenylphosphine (DPP) Modification with Versatile Properties

Fine adjustment of emission wavelength, light-conversion quality, photostability of blue-violet light conversion agents based on FRET effect

“Living” Fluorophores: Thermo-Driven Reversible ACQ-AIE Transformation and Ultra-Sensitive In-Situ Monitor for Dynamic Diels-Alder Reactions

D-A Structured High Efficiency Solid Luminogens with Tunable Emissions: Molecular Design and Photophysical Properties

ACQ-to-AIE Transformation by Regioisomerization of Rofecoxib Derivatives for Developing Novel Mechanochromic and Acidochromic Materials

De(sulfon)amidative Cyclization: The Synthesis of Dibenzolactams and Dibenzosultams for Organic Light Emitting Diode Materials

Synthesis, characterization, and photophysical properties of dicyanoarylamine‐based semi‐aromatic polymers

AIE-active 9,10-bis(alkylarylvinyl)anthracences with pendent diethoxylphosphorylmethyl groups as solution-processable efficient EL luminophores

Cationic tetraphenylethylene-based AIE-active acrylonitriles: investigating the regioisomeric effect, mechanochromism, and wash-free bioimaging

Synthesis Of Amphiphilic Carbon Quantum Dots With Phosphorescence Properties And Their Multifunctional Applications

Recent progress on the construction and application of dithienylethene-based photochromic AIEgens

Exploring highly efficient light conversion agents for agricultural film based on aggregation induced emission effects