Abstract:STATEMENT OF PROBLEM:Sealing products have been produced to reduce microleakage at the implant abutment interface. However, little is known about their effectiveness and any alterations in mechanical behavior of implant systems with their application.PURPOSE:The purpose of this in vitro study was to evaluate the effect of a silicone sealing gel on implant abutment interface microleakage, abutment screw torque loss, and thread wear of implant systems in a simulated oral environment.MATERIAL AND METHODS:Five specimens each of 3 implants systems (Nobel, Straumann, and WEGO) that included sealed and unsealed groups were analyzed (N=30). Before assembling the components, toluidine blue solution was injected to the implant intaglio cavity to evaluate implant abutment interface microleakage. After tightening to the recommended torque, 20 to 200 N of 30-degree off-axis dynamic force was applied at 2 Hz for 48 hours. The toluidine blue solution was extracted to test optical density values at 1, 3, 9, 24, 33, and 48 hours. Detorque values were measured before and after cycling loading, and torque loss rates were calculated. The abutment screw morphologies were observed by using scanning electron microscopy. The coefficient of friction tendency of applying sealing gel was explored with a ball-on-flat configuration. One-way ANOVA and Student t test were used for statistical analysis (α=.05).RESULTS:The optical density value increased with the loading time, especially for Straumann group. The sealing gel decreased the implant abutment interface microleakage of Straumann assemblies after cyclic loading of 9 hours (P=.044), whereas no statistical difference was found for Nobel (P=.140) or WEGO groups (P=.402) at 6 time points. Torque loss occurred during tightening and further increased after dynamic cyclic load in each group. Among the 3 implant systems, Straumann implants reported the best antiloosening property (P<.001). The application of sealing gel reduced the initial (P=.048) and final (P=.032) torque loss rate in all the 3 systems. Scanning electron microscopy observations revealed the bottom thread tended to have more abrasion than the first thread. After applying sealing gel, less thread abrasion was found in Nobel and WEGO assemblies, whereas the protective effect was not evident for the Straumann group. The coefficient of friction of sealed group (0.17 ±0.026) was significantly (P=.012) lower than that of unsealed group (0.24 ±0.044).CONCLUSIONS:The silicone sealing gel improved the immediate fastening and long-term antiloosening performances of 3 implant systems, decreased the implant abutment interface microleakage of Straumann system, and reduced abutment screw thread abrasion of the Nobel and WEGO systems.

Assessment of Microgap and Bacterial Leakage of Two Types of Internal Implant-Abutment Union

To Assess the Adequacy of Antimicrobial Sealing gel and O-ring at the Implant-Abutment Interface to Prevent the Microleakage - An in Vitro Study

A Retrospective Study of 12,538 Internal Conical Connection Implants Focused on the Long-Term Integrity of Implant-Abutment Complexes.

Microbial Leakage through Three Different Implant-Abutment Interfaces on Morse Taper Implants In Vitro

A New Experimental Design for Bacterial Microleakage Investigation at the Implant-Abutment Interface: An In Vitro Study

Contact analysis of gap formation at dental implant‐abutment interface under oblique loading: A numerical‐experimental study

Bacterial translocation and microgap formation at a novel conical indexed implant abutment system for single crowns

Microgap between zirconia abutments and titanium implants

Influence of the Use of Transepithelial Abutments vs. Titanium Base Abutments on Microgap Formation at the Dental Implant–Abutment Interface: An In Vitro Study

In Vitro Analysis of Microbiologic Sealing of Two Different Fixed Implant-Supported Prosthesis Designs Cemented By Four Different Dental Cements

In vitro analysis of the microbiological sealing of tapered implants after mechanical cycling

Comparative in vitro evaluation of microgap in titanium stock versus cobalt–chrome custom abutments on a conical connection implant: Effect of crown cementation and ceramic veneering

Effect of implant-abutment microgap on bone tissues surrounding the necks of implants

COMPARATIVE EVALUATION OF MICROLEAKAGE OF BIODENTINE AND GERISTORE ROOT END FILLING MATERIALS IN DRY, SALIVA AND BLOOD CONTAMINATED ENVIRONMENTS – A FLUORESCENT MICROSCOPE STUDY.

Implant Mechanics, Biological Milieu, and Peri-Implantitis: A Narrative Review

Effect of Sealing Gel on the Microleakage Resistance and Mechanical Behavior During Dynamic Loading of 3 Implant Systems.

Evaluation of microbial contamination in removable dental prosthesis at different time of usage

Microbial Leakage Evaluation Of Warm Gutta – Percha Techniques

Microbiological profile of peri-implantitis: Analyses of peri-implant microbiome

The Effects of Dental Hygiene Instruments on Streptococcus sanguinis Adhesion to Titanium Implant Abutments

Comparison of marginal adaptation of mineral trioxide aggregate, glass ionomer cement and intermediate restorative material as root-end filling materials, using scanning electron microscope: An in vitro study