Komorbidität von depressiven Störungen und kardiovaskulären Erkrankungen Implikationen für Diagnostik, Pharmako- und Psychotherapie

B. Hesslinger,M. Härter,J. Barth,D. Klecha,C. Bode,J. Walden,J. Bengel,M. Berger

DOI: https://doi.org/10.1007/s001150101168

2002-03-01

Der Nervenarzt

Abstract:

What problem does this paper attempt to address?

Development of diffusive gradients in thin-films technique for monitoring polycyclic aromatic hydrocarbons in coastal waters

Zishan Diao,Guoqin Feng,Weikun Xu,Fanping Zhu,Yiqiao Zhang,Jianlu Duan,Mengxin Xu,Xue Zhang,Xiaohan Zhang,Shan Zhao,Shuguang Wang,Xianzheng Yuan

DOI: https://doi.org/10.1016/j.jhazmat.2024.134384

IF: 13.6

2024-04-26

Journal of Hazardous Materials

Abstract:Addressing the challenge of accurately monitoring polycyclic aromatic hydrocarbons (PAHs) in aquatic systems, this study employed diffusive gradients in thin-films (DGT) technique to achieve methods detection limits as low as 0.02 ng L −1 to 0.05 ng L −1 through in situ preconcentration and determination of time-integrated concentrations. The efficacy of the developed DGT samplers was validated under diverse environmental conditions, demonstrating independence from factors such as pH (5.03–9.01), dissolved organic matter (0–20 mg L −1 ), and ionic strength (0.0001–0.6 M). Notably, the introduction of a novel theoretical approach to calculate diffusion coefficients based on solvent-accessible volume tailored for PAHs significantly enhanced the method's applicability, particularly for organic pollutants with low solubility. Field deployments in coastal zones validated the DGT method against traditional grab sampling, with findings advocating a 4 to 7-day optimal deployment duration for balancing sensitivity and mitigating lag time effects. These results provide a sophisticated, efficient solution to the persistent challenge of monitoring hydrophobic organic pollutants in aquatic environments, broadening the scope and applicability of DGT in environmental science and providing a robust tool for researchers.

environmental sciences,engineering, environmental
Simple and Rapid Analysis of Phthalate Esters in Marine Sediment Using Ultrasound-Assisted Extraction Combined with Gas Purge Microsyringe Extraction Followed by GC-MS.

Xiangai Zhao,Haiyan Jin,Donghao Li,Han Yeong Kaw,Meiyu Cui,Zhongqiang Ji

DOI: https://doi.org/10.1016/j.marpolbul.2020.111667

IF: 5.8

2020-01-01

Marine Pollution Bulletin

Abstract:Phthalate esters (PAEs) are a class of the emerging pollutants that pose a potential environmental threat to marine ecosystems. In this study, a simple analytical method using ultrasound-assisted extraction combined with gas purges microsyringe extraction (GP-MSE) coupled with GC-MS was utilized for the reliable and rapid determination of PAEs in different types of marine sediment. The analytical results showed that the method exhibited excellent reproducibility, linear responses, and detection limits, which verified the suitability of the method for the determination of PAEs in marine sediment. This approach requires minimal reagents, solvents, and sample pretreatment procedures as well as a short analysis time; thus, procedural blanks can be kept to a minimum. This method was demonstrated to be a highly efficient and sensitive quantitative analytical method for the simple detection of PAEs in marine sediment.
Measuring Freely Dissolved DDT and Metabolites in Seawater Using Solid-Phase Microextraction with Performance Reference Compounds

Kunde Lin,Wenjian Lao,Zhijiang Lu,Fang Jia,Keith Maruya,Jay Gan

DOI: https://doi.org/10.1016/j.scitotenv.2017.05.022

2017-01-01

Abstract:The coupling of disposable solid-phase microextraction (SPME) with performance reference compounds (PRCs) has been recently introduced to measure time-averaged freely dissolved concentrations (Cfree) of hydrophobic organic contaminants in sediments under laboratory conditions. To explore the use of PRC-SPME for in situ sampling in seawater, disposable PDMS fibers (35-μm and 100-μm coating) preloaded with stable isotope labeled analogues as PRCs were deployed at six stations (each with three depths) in the open ocean of the Palos Verdes Shelf (CA, USA) Superfund site for 33d to measure Cfree of DDT and its degradates. The observed values of fractional equilibration (feq) of PRCs were mostly <0.85, suggesting nonequilibrium conditions at the end of deployment. The observed feqs for the samplers varied with compound, sampling station and depth, validating the need for calibration to derive accurate Cfree. The Cfree values of DDE and DDD determined with PRC-SPME were in good agreement with those previously measured by in situ large-volume water sampling or polyethylene devices. The highest Cfree in seawater 5m off the ocean floor was 750pgL−1 for o,p′-DDE, 2170pgL−1 for p,p′-DDE, 24pgL−1 for o,p′-DDD, and 75pgL−1 for p,p′-DDD. Results of this study demonstrated the feasibility and advantages of using disposable PDMS fiber coupled with PRCs for in situ sampling.
Development and Applications of Novel DGT Passive Samplers for Measuring 12 Per- and Polyfluoroalkyl Substances in Natural Waters and Wastewaters.

Zhou Fang,Yuan Li,Yanying Li,Danxing Yang,Hao Zhang,Kevin C. Jones,Cheng Gu,Jun Luo

DOI: https://doi.org/10.1021/acs.est.0c08092

IF: 11.4

2021-01-01

Environmental Science & Technology

Abstract:Extensive and long-term use of per- and polyfluoroalkyl substances (PFASs) has caused their widespread distribution in aquatic systems. A new diffusive gradients in thin-films (DGT) passive sampling method based on weak anion exchanger (WAX) binding layer is developed here for monitoring five perfluoroalkyl carboxylic acids (PFCAs), five perfluoroalkanesulfonic acids (PFSAs) and two PFASs (6:2 FTSA and GenX) in waters. Performance of WAX-DGTs was independent of environmental conditions, namely pH (3.03-8.96), ionic strength (1-500 mM), and DOM content (4-30 mg L-1). Diffusion coefficients (D) of the 12 PFASs in the diffusive gels were measured, 9 for the first time. Linear correlations between D and perfluoroalkyl chain lengths (CF2) were established to obtain D for congener chemicals with the similar functional group and structure. The binding capacity of the WAX-DGT sampler was at least 440 μg PFASs per sampler, sufficient for applications in waters across a wide range of conditions and PFASs concentrations. Successful applications of WAX based DGT samplers in a wastewater treatment plant (WWTP) and three rivers has demonstrated that DGT is a powerful tool for monitoring, surveillance and research of these 12 PFASs in aquatic systems, and can be extended to wider suites of PFs in future.
Investigating Potential Limitations of Current Diffusive Gradients in Thin Films (DGT) Samplers for Measuring Organic Chemicals

Runmei Wang,Yitao Zou,Jun Luo,Kevin C. Jones,Hao Zhang

DOI: https://doi.org/10.1021/acs.analchem.9b02571

IF: 7.4

2019-01-01

Analytical Chemistry

Abstract:The diffusive gradients in thin films (DGT) passive sampler has emerged as a powerful tool for measuring in situ concentrations of organic contaminants in waters with appropriate spatial and temporal resolution at low cost. This study addresses the property range of compounds which can be routinely sampled with the present design of DGT device. Sorption experiments and DGT deployment with 9 model chemicals [organophosphate esters with a wide range of log K-OW (0.8-9.5), molecular weight (182-435 Da)] and different functional groups showed compounds with high hydrophobicity and aromatic rings are prone to retention on membrane filters, which slows the supply of chemical to the binding resin of the sampler. The current DGT sampler (PTFE membrane filter, agarose gel diffusion layer, and HLB binding layer) is potentially reliable for measuring hydrophilic [log K-OW (0.8-2.6)] and nonaromatic-ring chemicals. For compounds of higher values of K-OW or with aromatic rings, knowledge of the lag phase is necessary to optimize sampling times to avoid biasing subsequent laboratory analyses. A standard procedure is used to measure lag times (from minutes to days) by exposing a series of DGT samplers in waters until linear mass accumulation in samplers is achieved. We discuss how monitoring of a wide array of organic contaminants across classes should be possible in the future with a range of validated new DGT devices, optimized for the choice of membrane filter, diffusive material, and binding resin.
[Clinical studies of varicocele. 3: A rare venous return via Santorini's plexus in a varicocele patient. Report of a case].

R. Yasumoto,M. Asakawa,K. Kakinoki,H. Kobayakawa

1988-02-01

Abstract:A 12-year-old man was referred to our clinic because of sanguineous discharge. At the out-patient department, bilateral varicocele was found. Urinalysis showed microscopic hematuria, but no other laboratory data were abnormal. Excretion urography was normal. The retrograde phlebograph showed a rare venous return via Santorini's plexus and lumbar veins. After varicocelectomy, urinalysis improved.
In Situ Measurement of Perfluoroalkyl Substances in Aquatic Systems Using Diffusive Gradients in Thin-Films Technique.

Dong-Xing Guan,Ya-Qing Li,Nan-Yang Yu,Guang-Hui Yu,Si Wei,Hao Zhang,William Davison,Xin-Yi Cui,Lena Q Ma,Jun Luo

DOI: https://doi.org/10.1016/j.watres.2018.07.031

IF: 12.8

2018-01-01

Water Research

Abstract:To better understand the environmental impact of ubiquitous perfluoroalkyl substances (PFASs) in waters, reliable and robust measurement techniques are needed. As one of the most widely used passive sampling approaches, diffusive gradients in thin-films (DGT) is not only easy to handle but also provides time-weighted analyte concentrations. Based on DGT with XAD18 as a binding agent, we developed a new methodology to measure two frequently detected PFASs in surface waters and wastewaters, i.e. perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS). Their diffusion coefficients in the diffusive gel, measured using an independent diffusion cell, were 4.37 × 10-6 and 5.08 × 10-6 cm2 s-1 at 25 °C, respectively. DGT had a high capacity for PFOA and PFOS at 196 and 246 μg per gel disk, suggesting the DGT sampler was suitable for deployment of several weeks. Time-integrated concentrations of PFOA and PFOS in a natural lake and river, and a municipal wastewater treatment plant effluent using DGT samplers deployed in situ for 12-33 d were comparable to those measured by a solid-phase extraction method coupled with high-frequency grab sampling. This study demonstrates that DGT is an effective tool for in situ monitoring of PFASs in natural waters and wastewaters.
Development of new PDMS in tube extraction microdevice for enhanced monitoring of polycyclic aromatic hydrocarbons and their derivatives in water

Nathan de Souza Coelho,Helvécio Costa Menezes,Zenilda de Lourdes Cardeal

DOI: https://doi.org/10.1016/j.talanta.2024.126882

IF: 6.1

2024-09-20

Talanta

Abstract:Contamination by polycyclic aromatic hydrocarbons (PAHs) is an urgent environmental concern, given its atmospheric dispersion and deposition in water bodies and soils. These compounds and their nitrated and oxygenated derivatives, which can exhibit high toxicities, are prioritized in environmental analysis contexts. Amid the demand for precise analytical techniques, comprehensive two-dimensional chromatography coupled with mass spectrometry (GCxGC/Q-TOFMS) has emerged as a promising tool, especially in the face of challenges like co-elution. This study introduces an innovation in the pre-concentration and detection of PAHs using an extraction fiber based on polydimethylsiloxane (PDMS), offering greater robustness and versatility. The proposed technique, termed in-tube extraction, was developed and optimized to effectively retain PAHs and their derivatives in aqueous media, followed by GCxGC/Q-TOFMS determination. Fiber characterization, using techniques such as TG, DTG, FTIR, and SEM, confirmed the hydrophobic compounds retention properties of the PDMS. The determination method was validated, pointing to a significant advancement in the detection and analysis of PAHs in the environment, and proved effective even for traces of these compounds. The results showed that the detection limits (LOD) and quantification limits (LOQ) ranged from 0.07 ng L −1 to 1.50 ng L −1 and 0.33 ng L −1 to 6.65 ng L −1 , respectively; recovery ranged between 72 % and 117 %; and the precision intraday and interday ranged from 1 % to 20 %. The fibers were calibrated in the laboratory, with exposure times for analysis in the equilibrium region ranging from 3 to 10 days. The partition coefficients between PDMS and water were also evaluated, showing logarithm values ranging from 2.78 to 5.98. The fibers were applied to the analysis of real water samples, demonstrating high capacity. Additionally, given the growing demand for sustainable methods, the approach presented here incorporates green chemistry principles, providing an efficient and eco-friendly solution to the current chemical analysis scenario.

chemistry, analytical
Evaluation and Application of a Novel Diffusive Gradients in Thin-Films Technique for in Situ Monitoring of Glucocorticoids in Natural Waters

Liying Yan,Qiuyu Rong,Hao Zhang,Kevin C. Jones,Yanying Li,Jun Luo

DOI: https://doi.org/10.1021/acs.est.2c00834

IF: 11.4

2022-01-01

Environmental Science & Technology

Abstract:The potential environmental risks of glucocorticoids (GCs) have attracted attention in the past few decades. In this study, a novel diffusive gradients in thin-films (DGT) device and analytical technique based on the second generation of polar enhanced phase (PEP-2), PEP-2-DGT, were developed for sampling and quantifying natural and synthetic GCs in aquatic systems. The capacity of PEP-2 gels for accumulating all target compounds was >600 μg per disc, sufficient for long-term passive sampling of selected GCs, even in wastewaters. Systematic tests were carried out to verify the application of DGT in natural waters and wastewaters. The performance of PEP-2-DGT devices was independent (CDGT/Csoln was in the acceptable range of 0.9-1.1) of a wide range of environmental conditions: ionic strength (0.001-0.5 mol L-1), dissolved organic matter (0-20 mg L-1), and pH (3.06-9.02). It was tested for various diffusive layer thicknesses (0.565-2.065 mm) and different deployment times (10-168 h). Diffusion coefficients (D) of selected GCs through an agarose-based diffusive gel were determined for the first time (3.80-4.85 × 10-6 cm-2 s -1 at 25 °C). Linear correlations between D and log Kow were established for three groups of target GCs (R2 = 0.96-0.99). This could enable prediction of D values for other GCs with similar structures in the future, which will help for rapid screening and emergency monitoring. Concentrations and distribution patterns of analytes obtained by PEP-2-DGT devices in five rivers after 7- and 14-day deployments were in accordance with those measured from grab samples, with total GC concentrations ranging from 7 to 27 ng L-1 at all sampling sites, confirming the reliability and robustness of the DGT devices for monitoring GCs in natural waters. The development of the new DGT technique will help improve understanding of the behavior and fate of these compounds in the aquatic environments.
Utility of a modified o-DGT passive sampler for measurement of bisphenol analogues in freshwater and coastal waters

Po Wang,Jie Li,Meng Yi Xie,Chen Chou Wu,Charles S Wong,Eddy Y Zeng

DOI: https://doi.org/10.1016/j.scitotenv.2024.172978

2024-06-25

Abstract:Bisphenol analogues (BPs) are commonly found in riverine and coastal waters. However, the lack of a reliable and robust passive sampling method has hindered our ability to monitor these compounds in aquatic systems. The study developed a novel organic-diffusive gradients in thin film (o-DGT) sampler based on stainless steel mesh membrane, polyacrylamide diffusive gel, and hydrophilic-lipophilic balance (HLB) binding gel. This innovative design tackled issues of filter membrane sorption in traditional o-DGT devices and potential gel damage in membrane-less o-DGT devices, showing promising application prospects. The mass accumulation of 15 target BPs was linear over 10 days in both freshwater (r2 ≥ 0.92) and seawater (r2 ≥ 0.94), with no saturation observed. The diffusion coefficients (D) through polyacrylamide diffusive gels ranged from 4.04 × 10-6 to 5.77 × 10-6 cm2 s-1 in freshwater and from 1.74 × 10-6 to 4.69 × 10-6 cm2 s-1 in seawater for the target BPs (except for bisphenol PH) at 22 °C. The D values of the target BPs in seawater were lower than those in freshwater due to the high salinity in seawater (35 ‰). The o-DGT samplers demonstrated good integrity in field applications. The total concentrations of the eight detected BPs ranged from 9.2 to 323 ng L-1, which was consistent with the measurements obtained by grab sampling. Among all BPs, bisphenol S, bisphenol F, and bisphenol A were consistently detected at all sites using both sampling methods. The concentrations of some novel BPs in coastal water measured by grab sampling were comparable to those measured in rivers, suggesting the need to strengthen pollution control of BPs in coastal areas. These results indicate that the o-DGT passive sampling method developed in the present study can be effectively used for monitoring BPs in freshwater and coastal environments.
Evaluation of the DGT passive samplers for integrating fluctuating concentrations of pharmaceuticals in surface water

Hongmei Cao,Qingwei Bu,Qingshan Li,Lei Yang,Jianfeng Tang,Gang Yu

DOI: https://doi.org/10.1016/j.scitotenv.2024.172067

2024-05-01

Abstract:Diffusive gradients in thin films (DGTs) have been well-documented for the measurement of a broad range of organic pollutants in surface water. However, the performance has been challenged by the inherent periodic concentration fluctuations for most organic pollutants. Therefore, there is an urgent need to assess the true time-weighted average (TWA) concentration based on fluctuating concentration profiles. The study aimed to evaluate the responsiveness of DGT and accuracy of TWA concentrations, considering various concentration fluctuating scenarios of 20 pharmaceuticals in surface water. The reliability and accuracy of the TWA concentrations measured by the DGT were assessed by comparison with the sum of cumulative mass of DGT exposed at different stages over the deployment period. The results showed that peak concentration duration (1-5 days), peak concentration fluctuation intensity (6-20 times), and occurrence time of peak concentration fluctuation (early, middle, and late stages) have minimal effect on DGT's response to most target pharmaceutical concentration fluctuations (0.8 < CDGT/CTWA < 1.2). While the downward-bent accumulations of a few pharmaceuticals on DGT occur as the sampling time increases, which could be accounted for by capacity effects during a long-time sampling period. Additionally, the DGT device had good sampling performance in recording short fluctuating concentrations from a pulse event returning to background concentrations with variable intensity and duration. This study revealed a satisfactory capacity for the evaluation of the TWA concentration of pharmaceuticals integrated over the period of different pulse deployment for DGT, suggesting that this passive sampler is ideally suited as a monitoring tool for field application. This study represents the first trial for evaluating DGT sampling performance for pharmaceuticals with multiple concentration fluctuating scenarios over time, which would be valuable for assessing the pollution status in future monitoring campaign.

environmental sciences
Development and Application of the Diffusive Gradients in Thin-Films Technique for Measuring Psychiatric Pharmaceuticals in Natural Waters.

Zhou Fang,Kexin Li,Yuan Li,Hao Zhang,Kevin C. Jones,Xinyu Liu,Shengyu Liu,Lena Q. Ma,Jun Luo

DOI: https://doi.org/10.1021/acs.est.9b03166

IF: 11.4

2019-01-01

Environmental Science & Technology

Abstract:Psychiatric pharmaceuticals are widely distributed in the aquatic environment and have attracted recent attention due to their potential for environmental effects. A robust and reliable in situ passive sampling approach, the diffusive gradients in thin-films (DGT) technique, is developed here to measure 14 psychiatric pharmaceuticals. A new binding material, mixed-mode cation exchange resin (Poly-Sery MCX, 40 mu m, CNW, Germany), was used for the first time in DGT and compared to XAD and HLB. Reliable elution efficiencies of the pharmaceuticals from the binding gels were obtained in methanol/ammonia, and diffusion coefficients for all the compounds were determined. The influence of diffusive layer thickness (0.515-2.015 mm), deployment time (3-168 h), and important environmental conditions-pH (3.02-9.45), ionic strength (0.0001-0.5 M), and dissolved organic matter (0-20 mg L-1)-were evaluated. The capacity of XAD, HLB, and MCX gels for binding all the test pharmaceuticals was similar to 335 mu g per disc, meaning that DGT could theoretically be deployed for over 30 months if there are no competitive effects or confounding factors. The uptake kinetics of psychiatric pharmaceuticals onto MCX gel were much faster than those onto XAD and HLB gels in the first hour. DGT measured concentrations of test pharmaceuticals at two sample points in a river (over 6 days) were comparable to those obtained by grab sampling. This study demonstrates the accuracy and reliability of DGT for measuring psychiatric pharmaceuticals across a wide range of freshwater conditions found in the natural environment.
[Chronic renal insufficiency and renal transplantation in systemic deposition of light chains: report of 2 cases].

E. David Neto,L. Saldanha,L. Ianhez,E. Sabbaga

Revista do Hospital das Clínicas

Abstract:
Measurement of perfluoroalkyl substances in drinking water sources by DGT sampler with a novel fluorinated graphite binding gel

Fan Dong,Fan Ge,Xinting Zhao,Daming Sun,Suyu Ren,Yan Wang,Feng Tan

DOI: https://doi.org/10.1016/j.scitotenv.2023.169658

2024-02-20

Abstract:Extensive use of per- and polyfluoroalkyl substances (PFASs) has resulted in their widespread presence in natural waters. Concern for public health requires reliable measurement methods for determining their distribution and risks. Here, a sampling method based on diffusive gradients in thin films (DGT) was developed for measuring PFASs in drinking water sources. Fluorinated graphite (FG) particles were used to prepare the DGT binding gel for selective enrichment of trace PFASs in an aqueous environment. The FG-DGT method did not show sensitivity to relevant environmental parameters including pH (5.0-9.0), ionic strength (0.001-0.5 M), or DOM concentration (0-30 mg/L). The FG-DGT had enough capacity for deployment of up to four months. Six traditional and emerging PFASs including PFOS, PFOA, PFHpA, PFHxS, PFNA, and 6:2 FTSA at the ng/L level were detected in two major reservoirs serving as public drinking water sources by FG-DGT method coupled with liquid chromatography tandem mass spectrometry (LC-MS/MS). PFOA appeared at the highest observed concentrations in the drinking water sources. The research demonstrates that FG-DGT is an effective and efficient tool for monitoring PFASs in drinking water.
A Novel Enhanced Diffusion Sampler for Collecting Gaseous Pollutants Without Air Agitation.

Xuelian Pan,Shaojie Zhuo,Qirui Zhong,Yuanchen Chen,Wei Du,Hefa Cheng,Xilong Wang,Eddy Y. Zeng,Baoshan Xing,Shu Tao

DOI: https://doi.org/10.1080/10934529.2018.1444973

2018-01-01

Abstract:A novel enhanced diffusion sampler for collecting gaseous phase polycyclic aromatic hydrocarbons (PAHs) without air agitation is proposed. The diffusion of target compounds into a sampling chamber is facilitated by continuously purging through a closed-loop flow to create a large concentration difference between the ambient air and the air in the sampling chamber. A glass-fiber filter-based prototype was developed. It was demonstrated that the device could collect gaseous PAHs at a much higher rate (1.6 +/- 1.4L/min) than regular passive samplers, while the ambient air is not agitated. The prototype was also tested in both the laboratory and field for characterizing the concentration gradients over a short distance from the soil surface. The sampler has potential to be applied in other similar situations to characterize the concentration profiles of other chemicals.
Long-term deployment of commonly used DGT devices for trace element measurement across laboratory and field settings

Zhou Fang,Ying Su,Yaqin Yu,Huaijian Zhang,Xintian Qian

DOI: https://doi.org/10.1016/j.aca.2024.343230

2024-11-15

Abstract:Diffusive Gradients in Thin-films (DGT) technique is a promising passive sampling technique, which was used for the determination of lots of inorganic and organic pollutants. Although many DGT devices have not been extensively tested and verified in field, DGT device such as LSNP-NP, LSNT-NP, LSNZ-NP, and LSNM-NP DGT were widely employed for the assessment of various trace elements. However, the deployment time of these DGTs were much shorter than the theoretical time in the preexisting literature. Therefore, the performance of DGT for long-term application in different water bodies is not known. This investigation utilized the four DGTs for the assessment of various trace elements across extended periods both in controlled laboratory settings and natural field environments. Synthetic soft, hard, and seawater compositions served as media for laboratory deployments. Most elements can be measured accurately in 4-7 days in soft and hard water. Deployment durations in seawater exhibited a notable reduction compared to those in freshwater matrices. LSNZ-NP DGT excelling in oxyanion determination, while LSNT-NP DGT showcased superior efficacy in phosphorus quantification. Field deployments in rivers and sea affirmed the robustness of LSNZ-NP DGT, evidencing prolonged deployment capabilities for various elements, such as Mo, Se, As, Sb, and P, spanning 7-28 days. Assessment of pollution levels across four sampling sites revealed heightened concentrations of most elements in marine waters relative to riverine environments, except for phosphorus. Notably, all assessed elements, except for phosphorus, conformed to Class I water quality standards. This study demonstrated the difference between the theoretical application time and actual application time for the first time. It raises new questions for the application of DGT in nature water bodies. The mechanization of the difference between the theoretical and actual application time should be studied in the future research. The measures to extend the application time should be studied too.
Field evaluation of diffusive gradients in thin-film passive samplers for wastewater-based epidemiology

Xin Liu,Ruiling Zhang,Hao Cheng,Mahdi Safaei Khorram,Shizhen Zhao,Trinh Thi Tham,Tri Manh Tran,Tu Binh Minh,Bin Jiang,Biao Jin,Gan Zhang

DOI: https://doi.org/10.1016/j.scitotenv.2021.145480

2021-06-01

Abstract:There is a need for a simple water sampling technique to enable routine monitoring of community drug consumption through wastewater-based epidemiology (WBE). This study investigates the potential use of diffusive gradients in thin films to sample organic compounds (o-DGT) for WBE. Three types of resin gels (HLB, XAD 18, and XDA-1) within o-DGT samplers each were deployed in triplicate at the inlets of two sewage treatment plants of Southern Asian cities. The target compounds included 15 illicit drugs and 18 antibiotics. A comprehensive evaluation was undertaken regarding each resin's ability to accumulate the target compounds and accuracy by comparing active samples. The organic compounds accumulated on each resin gel were characterised at the molecular level using Fourier transform ion-cyclotron-resonance mass spectrometry (FT-ICR MS). The results showed that the HLB resin performed better than the XAD 18 and XDA-1 resins. Based on calculations using the HLB-DGT data, methamphetamine and heroin were the two most popular illicit drugs consumed among the studied populations, and were followed by ketamine and codeine, which agreed well with the authoritative reports and reference data. The total drug consumption in Hanoi was one order of magnitude higher than that in Guangzhou, thus implying a probably more serious drug situation in the former. Overall, the findings of this study demonstrate that o-DGT passive samplers are a promising tool for WBE studies, particularly at WWTPs or in urban streams where an automatic sampler for taking composite water samples is absent.

environmental sciences
Development and validation of diffusive gradients in thin-films for in situ monitoring of ionic liquids in waters

Si-si Liu,Shi-bao Chen,Yu-bo Yue,Xiao-hao Li,Chi Zhang,Guang-Guo Ying,Chang-Er Chen

DOI: https://doi.org/10.1039/d4ay01730g

IF: 3.1

2024-10-25

Analytical Methods

Abstract:Due to their wide applications, occurrence and "PFAS-like" environmental behaviors, ionic liquids (ILs) represent a new challenge for the environmental monitoring community, who require robust analytical methods that can determine accurately and efficiently their environmentally relevant concentrations. A new passive sampling method based on the diffusive gradients in thin films (DGT) technique was developed for the measurement of imidazole-based ILs in waters using a mixed-mode cation exchange (MCX) resin as the adsorbent. The selected binding gel had a high binding capacity (>170 μg per disc) for ILs. Diffusion coefficients measured using a diffusion cell correlated well with alkyl chain lengths ( r 2 = 0.95) and retention times ( r 2 = 0.88), providing a simple and rapid prediction approach for other ILs. The assembled MCX-DGT sampler exhibited a linear accumulation for at least 120 h. MCX-DGT also showed good performance under typical freshwater conditions (pH 5–8, ionic strength 0.001–0.01 M, and humic acid 0–5 mg L −1 ), while still being problematic for aquatic conditions with higher ionic strength (>0.1 M) or DOM (>10 mg L −1 ). Laboratory deployment (for up to 3 days) in spiked natural freshwater (SNW) resulted in linear mass uptakes for the short-chain ILs (C2–C8), and their DGT-measured concentrations agreed well with solution concentrations. However, MCX-DGT significantly overestimated the concentrations of the long-chain ILs (C10–C12) when deployed in SNW for one day or more, which is attributed to the strong competitive adsorption of the long-chain ILs by natural organic matter. In situ field evaluation along with grab sampling found no target ILs in a wastewater treatment plant and its receiving river, implying that these new chemicals might not be widely used in South China now. This is the first report on the DGT technique for ILs and might provide an effective tool for monitoring short chain length ILs in the aquatic environment in the near future.

spectroscopy,chemistry, analytical,food science & technology
A Needle Extraction Device Packed with Molecularly Imprinted Polymer Functionalized Fiber for the Determination of Polycyclic Aromatic Hydrocarbon in Water

Boying Yue,Xiaoyu Zhang,Xiyue Wang,Lili Lian,Wenxiu Gao,Hao Zhang,Shuang Hou,Dawei Lou

DOI: https://doi.org/10.1007/s11270-021-05471-y

2022-01-01

Abstract:Polycyclic aromatic hydrocarbon (PAHs) is an important organic contaminant substance in the environment. Their concentration monitoring is of great significance for predicting the potential environmental risk and protecting the organism safety. Here, molecularly imprinted polymers (MIPs) coating was prepared on zylon heat-resistant fiber by in situ polymerization, which was packed to a stainless steel needle to develop a needle-type device (NTD) for the analysis of PAHs. Pyrene was used as the template molecule in this MIPs. To obtain excellent selectivity and adsorption efficiency, 4-vinylpyridine (4-VP) and ethylene glycol dimethacrylate (EDMA) were chosen as functional monomers and cross-linker, respectively, and the ratio of ingredients was optimized. The scanning electron microscope (SEM) was used for identifying micro-morphologic characteristics of the obtained MIPs-coating fiber. The PAHs from environmental water samples were extracted with the NTD by headspace extraction and detected by gas chromatography with a flame ionization detector (GC-FID). Under optimized conditions, the proposed method exhibited a good linearity dynamic range (LDR) of 0.5–1800 µg·L−1 with the correlation coefficients (R2) between 0.9953 and 0.9977. The limits of detection are in the ranges of 0.09–0.40 µg·L−1 and the limits of quantification are in the ranges of 0.37–1.40 µg·L−1. Furthermore, the device showed remarkable durability and storage capacity. It could be reused 60 times, and the loss ratio was less than 15% with relative standard deviations (RSDs) less than 6.4% after 3 days of storage. The developed method is easy, sensitive, and accurate, and it can be used for detection of trace PAHs in water sample.
Activated charcoal based diffusive gradients in thin films for in situ monitoring of bisphenols in waters.

Jian-Lun Zheng,Dong-Xing Guan,Jun Luo,Hao Zhang,William Davison,Xin-Yi Cui,Lian-Hong Wang,Lena Q Ma

DOI: https://doi.org/10.1021/ac503814j

IF: 7.4

2015-01-01

Analytical Chemistry

Abstract:Widespread use of bisphenols (BPs) in our daily life results in their elevated concentrations in waters and the need to study their environmental impact, which demands reliable and robust measurement techniques. Diffusive gradients in thin films (DGT) is an in situ passive sampling approach which provides time-integrated data. In this study we developed a new methodology, based on DGT with activated charcoal (AC) as a binding agent, for measuring three BPs (BPA, BPB, and BPF) which incorporated and tested its performance characteristics. Consistent elution efficiencies were obtained using methanol when concentrations of BPs were low and a methanol-NaOH mixture at high concentrations. The diffusion coefficients of BPA, BPB, and BPF in the diffusive gel, measured using an independent diffusion cell, were 5.03 x 10(-6), 5.64 x 10(-6), and 4.44 x 10(-6) cm(2) s(-1) at 25 degrees C, respectively. DGT with an AC binding gel had a high capacity for BPA, BPB, and BPF at 192, 140, and 194 mu g/binding gel disk, respectively, and the binding performance did not deteriorate with time, up to 254 d after production. Time-integrated concentrations of BPs measured in natural waters using DGT devices with AC gels deployed in situ for 7 d were comparable to concentrations measured by an active sampling method. This study demonstrates that AC-based DGT is an effective tool for in situ monitoring of BPs in waters.

Komorbidität von depressiven Störungen und kardiovaskulären Erkrankungen Implikationen für Diagnostik, Pharmako- und Psychotherapie

Development of diffusive gradients in thin-films technique for monitoring polycyclic aromatic hydrocarbons in coastal waters

Simple and Rapid Analysis of Phthalate Esters in Marine Sediment Using Ultrasound-Assisted Extraction Combined with Gas Purge Microsyringe Extraction Followed by GC-MS.

Measuring Freely Dissolved DDT and Metabolites in Seawater Using Solid-Phase Microextraction with Performance Reference Compounds

Development and Applications of Novel DGT Passive Samplers for Measuring 12 Per- and Polyfluoroalkyl Substances in Natural Waters and Wastewaters.

Investigating Potential Limitations of Current Diffusive Gradients in Thin Films (DGT) Samplers for Measuring Organic Chemicals

[Clinical studies of varicocele. 3: A rare venous return via Santorini's plexus in a varicocele patient. Report of a case].

In Situ Measurement of Perfluoroalkyl Substances in Aquatic Systems Using Diffusive Gradients in Thin-Films Technique.

Development of new PDMS in tube extraction microdevice for enhanced monitoring of polycyclic aromatic hydrocarbons and their derivatives in water

Evaluation and Application of a Novel Diffusive Gradients in Thin-Films Technique for in Situ Monitoring of Glucocorticoids in Natural Waters

Utility of a modified o-DGT passive sampler for measurement of bisphenol analogues in freshwater and coastal waters

Evaluation of the DGT passive samplers for integrating fluctuating concentrations of pharmaceuticals in surface water

Development and Application of the Diffusive Gradients in Thin-Films Technique for Measuring Psychiatric Pharmaceuticals in Natural Waters.

[Chronic renal insufficiency and renal transplantation in systemic deposition of light chains: report of 2 cases].

Measurement of perfluoroalkyl substances in drinking water sources by DGT sampler with a novel fluorinated graphite binding gel

A Novel Enhanced Diffusion Sampler for Collecting Gaseous Pollutants Without Air Agitation.

Long-term deployment of commonly used DGT devices for trace element measurement across laboratory and field settings

Field evaluation of diffusive gradients in thin-film passive samplers for wastewater-based epidemiology

Development and validation of diffusive gradients in thin-films for in situ monitoring of ionic liquids in waters

A Needle Extraction Device Packed with Molecularly Imprinted Polymer Functionalized Fiber for the Determination of Polycyclic Aromatic Hydrocarbon in Water

Activated charcoal based diffusive gradients in thin films for in situ monitoring of bisphenols in waters.