Abstract:Since the polyethylene terephthalate (PET)/hollow glass beads (HGB) composite has a longer relaxation time than pure PET, the corresponding aggregates made of PET chains and HGBs are expected to have larger characteristic sizes compared to PET and HGB. A composite of polyethylene terephthalate (PET) and hollow glass beads (HGB) with two different HGB sizes was prepared and investigated rheologically. When the HGB content reaches approximately 30 wt%, the PET/HGB composite changes from a Newtonian fluid to a pseudoplastic one within the measured frequency range. If the HGB content is below the critical value, the viscosity of the composite may be lower than that of the neat PET melt. This is because scrolling or sliding of the HGB in the PET melt increases the apparent shear rate and reduces the torque measured by the rheometer rotor. Meanwhile, the size of the HGB affects the viscosity of the composite. The 40 μm HGB has a more pronounced effect, resulting in higher viscosity than 50 μm HGB. Furthermore, the composite containing 40 μm HGB has a lower density than the one containing 50 μm HGB. This is because the 40 μm HGB has a lower breaking rate and higher volume fraction compared to the 50 μm HGB at the same mass fraction. The peak relaxation time of the PET/HGB composite increases with the HGB content, and higher temperatures correspond to shorter relaxation times. DSC analysis showed that the addition of HGB filler decreased the melting temperature and increased the crystallization temperature of the PET material. Since the PET/HGB composite has a longer relaxation time than pure PET, the corresponding aggregates made of PET chains and HGBs are expected to have larger characteristic sizes compared to PET and HGB. These sizes can be determined approximately using a grid drawing method. The coupling agent CS‐101 enhances the bonding between PET and HGB. This is evidenced by comparing the viscosity curves of the composite with and without the coupling agent. Highlights The polyethylene terephthalate (PET)/hollow glass beads (HGB) composites with low levels of HGB might exhibit unusual viscosity. Abnormal viscosity in molten PET occurs due to the rolling or sliding of HGB. The composites with high HGB levels may exhibit a solid‐like modulus plateau. The proposed aggregate consists of PET, HGB, and broken glass shards.

Effect of glass beads on the tensile and impact properties of polyurethane bark glue

Toughness Enhancement of Poly(lactic Acid), Bamboo Particle and Ultrafine Bamboo-Char Ternary Biocomposites by Polyethylene Glycol Plasticization

Modification of Unsaturated Polyester Resin by HTPB: Effect of Introducing Method of the Rubber

Experimental Analysis of Mechanical Properties about the Glass Bead-filled Polypropylene

Interface Effect on the Mechanical Behaviour of Rigid Particle Filled Polymer

Effect of Core-Shell Particles Dispersed Morphology on the Toughening Behavior of PBT/PC Blends

Effect of Surface Modifications of Carbon Black (CB) on the Properties of CB/polyurethane Foams

Toughening of PBT by POE/POE-g-GMA Elastomer Through Regulating Interfacial Adhesion and Toughening Mechanism

Rigid Polyurethane Foams Reinforced by Glass Beads

Rheological investigation on polyethylene terephthalate (PET) filled with hollow glass beads

Synergistic effect of the glass bead and continuous glass fibers on the low‐velocity impact resistance of nylon 6 matrix composites

Synergistic Effect of Polycarbonate on Reactive Core-Shell Particles Toughened Poly (butylene Terephthalate)

Tensile properties of rigid glass bead/HDPE composites

Inhibited Transesterification on the Properties of Reactive Core-Shell Particles Toughened Poly(Butylene Terephthalate) and Polycarbonate Blends

Friction and wear reduction effect of glass bubbles embedded in PDMS surface

Preparation and properties of glass fiber/PBAT shape memory composites

Toughening of Pbt/Pc Blends with Epoxy Functionalized Core-Shell Modifiers

Tensile and impact characterization of S-glass/epoxy composite laminates containing microscale borax, perlite, and sewage sludge ash particles

Effect of PBT Resin on the Structure and Properties of Core-Shell Particles Toughened PC

Damage to Rigid-Particle-filled Polymer under Cyclic Tension

Modification of the Reactive Core-Shell Particles Properties to Prepare PBT/PC Blends with Higher Toughness and Stiffness