Abstract:On-demand thermal management based on the Peltier effect of thermoelectric (TE) materials has attracted great attention due to its unique advantages of a simple structure, no moving parts, quietness, compactness, and precise temperature control. However, conventional bulk TE materials are inherently rigid, and it is therefore difficult to acquire close contact with heat sources and heat sinks with complex geometries, resulting in poor heat transfer and cooling ability. In addition, they are optically opaque and dense, blocking passive heat dissipation by thermal radiation and air convection. Tailoring TE materials with mid-infrared (IR) transparency and good flexibility to achieve both active and passive cooling remains a great challenge. Here, we report a nanoporous TE hybrid composed of (000l)-textured n-type Bi2Te3 nanocrystals anchored on a single-wall carbon nanotube (SWCNT) network. It achieves an in-plane power factor of ∼265 μW m–1 K–2 and a low thermal conductivity of ∼0.34 W m–1 K–1, yielding a TE figure of merit (ZT) value of ∼0.23 in the temperature range from room temperature to ∼373 K. This hybrid has excellent flexibility and a maximum IR transparency of ∼16%. Our results open a way to develop efficient TEs with both active and passive cooling abilities.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaelm.0c00617?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaelm.0c00617</a>.(Note 1) Determination of the preferred orientation; (Note 2) microstructural characterization of the hybrid film; (Note 3) analysis of TE properties of the hybrid film; (Note 4) analysis of thermal conductivity of the hybrid film; (Note 5) calculation of the active cooling heat flux; (Table S1) calculated orientation factors Fx of the hybrids with different Bi2Te3/SWCNT volume ratios; (Table S2) carrier concentration (n), carrier mobility (μ), and conductivity (σ) of hybrids with different Bi2Te3/SWCNT volume ratios at 300 K; (Table S3) active cooling flux, passive cooling flux, and their contributions to the total cooling flux of the hybrids with different Bi2Te3/SWCNT volume ratios; (Figure S1) EDS of the hybrid with a Bi2Te3/SWCNT volume ratio of ∼18; (Figure S2) lab-made apparatus for the bending flexibility test at different radii; (Figure S3) X-ray diffraction patterns of the hybrids with different Bi2Te3/SWCNT volume ratios of 1.5, 3, 4.5, 7.5, 10.5, 13.5, and 18; (Figure S4) TEM images of the Bi2Te3/SWCNT hybrid; (Figure S5) SEM images of the Bi2Te3/SWCNT hybrids; (Figure S6) TE properties of the hybrid films with Bi2Te3/SWCNT volume ratios of 0, 1.5, 3, 4.5, 7.5, 10.5, 13.5, and 18; (Figure S7) temperature-dependent Seebeck coefficients of the hybrids with Bi2Te3/SWCNT volume ratios of 7.5, 10.5, 13.5, and 18; (Figure S8) in-plane electrical conductivity, Seebeck coefficients, and thermal conductivity; (Figure S9) thermal conductivity of the hybrid film with a Bi2Te3/SWCNT volume ratio of 18; (Figure S10) lab-made femtosecond laser nano–micro cutting system; (Figure S11) IR transmittance of hybrid films with Bi2Te3/SWCNT volume ratios of 0, 1.5, 3, 4.5, 7.5, 10.5, 13.5, 18, 45, and 60 in the wavelength range of ∼2.5 to ∼5 μm; (Figure S12) reproducibility of the time-dependent IR radiation cooling test of the hybrids (<a class="ext-link" href="/doi/suppl/10.1021/acsaelm.0c00617/suppl_file/el0c00617_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Flexible Thermoelectric Films Based on Bi 2 Te 3 Nanowires and Boron Nitride Nanotube Networks with Carbon Doping

Flexible Thermoelectric Films Based on Bi2Te3 Nanosheets and Carbon Nanotube Network with High n-Type Performance

Flexible n-type thermoelectric composite films with enhanced performance through interface engineering and post-treatment

High thermoelectric performance of flexible nanocomposite films based on Bi2Te3 nanoplates and carbon nanotubes selected using ultracentrifugation

Green biopolymer-CNT films exhibit high thermoelectric power factor and electrical conductivity for low temperature heat energy harvesting

A Flexible and Infrared-Transparent Bi 2 Te 3 -Carbon Nanotube Thermoelectric Hybrid for both Active and Passive Cooling

Staggered-layer-boosted flexible Bi 2 Te 3 films with high thermoelectric performance

Flexible layer-structured Bi2Te3 thermoelectric on a carbon nanotube scaffold

High-Performance W-Doped Bi0.5Sb1.5Te3 Flexible Thermoelectric Films and Generators

Cellulose Fiber-Based Hierarchical Porous Bismuth Telluride for High-Performance Flexible and Tailorable Thermoelectrics.

High Thermoelectric and Flexible PEDOT/SWCNT/BC Nanoporous Films Derived from Aerogels

High-performance g-C 3 N 4 coated single-walled carbon nanotube composite films for flexible thermoelectric generators

Achieving High Thermoelectric Performance in Bi2(Te, Se)3 Thin Film with (00 l)-Oriented by Incorporating Tellurization and Selenization Processes

Promoting the Thermoelectric Performance of Single-Walled Carbon Nanotubes by Inserting Discotic Liquid-Crystal Molecules

Flexible layer-structured Bi 2 Te 3 thermoelectric on a carbon nanotube scaffold

N-type flexible Bi2Se3 nanosheets/SWCNTs composite films with improved thermoelectric performance for low-grade waste-heat harvesting

Bi 2 Te 3 -based flexible thermoelectric generator for wearable electronics

Thermoelectric Performance Enhancement of Film by Pulse Electric Field and Multi‐Nanocomposite Strategy

Thermoelectric properties of a vertically aligned carbon nanotube array with embedded bismuth telluride

Flexible Bi2Te3/PEDOT nanowire sandwich-like films towards high-performance wearable cross-plane thermoelectric generator and temperature sensor array

Enhanced Thermoelectric Properties of Bi2 Te3 -Based Micro-Nano Fibers Via Thermal Drawing and Interfacial Engineering.