Influence of pre-fermentative treatment on the fatty acid content of Saccharomyces cerevisiae (M(3)30-9) during alcoholic fermentation of grape must.

E. Valero,C. Millán,J. Ortega

DOI: https://doi.org/10.1016/S1389-1723(01)80052-9

IF: 3.185

Journal of Bioscience and Bioengineering

Abstract:

What problem does this paper attempt to address?

Experimental Research on Low Supercooling of Ice Storage and Analysis of Its Energy Saving

CHEN Kun,HONG Rong-hua,WU Jie,JIN Jing,SUN Zhi-jian

DOI: https://doi.org/10.3969/j.issn.1004-3950.2005.01.013

2005-01-01

Energy Engineering

Abstract:Based on the experimental data, different models during the phase change of solid-liquid in ice storage were studied in this research. An annulus solid ice began to grow slowly from the inside wall to the center region when there was no supercooling. Uniform solid-liquid mixtures shaped when there had supercooling. The thermal resistence was larger when there had no supercooling. The time required for complete solid ice growth was longer than there had supercooling. With the result, low supercooling would have the benefit to energy saving in cool storage air-conditioning system.
Effect of Liquid Nitrogen Spray Freezing on the Ice Crystal Size and Quality of Large Yellow Croaker

Yuxiao Mao,Lihui Hu,Shiyao Kuang,Yong Yu,Songming Zhu

DOI: https://doi.org/10.1016/j.jfoodeng.2024.111937

IF: 6.203

2024-01-01

Journal of Food Engineering

Abstract:Large yellow croakers (Larimichthys crocea) were frozen by liquid nitrogen spray freezing (LNSF), liquid immersion freezing (LIF), and air freezing (AF), and the freezing rate, ice crystal size and product qualities were compared. LNSF was found to be a promising freezing technology because of the significantly (P < 0.05) shortest freezing time, smallest ice crystal, and best overall product quality. Then, the effect of processing parameters during LNSF on freezing characteristics, and microstructure and qualities of samples was studied. Freezing time was reduced by decreasing freezing temperature and increasing air velocity. A size uniformity index was proposed in this study to evaluate the distribution uniformity of ice crystals. The minimum cross-sectional area (605.83 mu m(2)) with the best size uniformity was achieved at a freezing temperature of -90 degrees C, a final temperature of -30 degrees C, and an air velocity of 4 m/s, showing a reduction of 50.90% as compared to the maximum (1233.77 mu m(2)). The qualities of samples frozen by LNSF with the aforementioned parameter values were well maintained and met the industrial standard. Therefore, the developed LNSF protocol was recommended for the industrial application for large yellow croaker.
Numerical Simulation of Freezing Process of a Sessile Supercooled Water Droplet on a Cold Wall

Xuan ZHANG,Xiao-Min WU,Jing-Chun MIN

2018-01-01

Abstract:When supercooled droplets in clouds impinge and stick on aircraft in flight,icing phenomena may occur.The freezing process of a sessile supercooled water droplet on a cold surface is therefore numerically investigated.The simulations consider the gravity effect on the droplet shape and include the recalescence stage effect on the droplet freezing by adjusting the droplet physical properties and the simulation initial conditions.Calculations are performed based on the solidification/melting model in Fluent.The numerically calculated droplet freezing process agrees well with the experimental observation in the literature and the difference in the final freezing time is 12.5％.Further calculations are made to investigate the influences of supercooling degree,contact angle and airflow velocity on the freezing process,and the results show that greater supercooling degree,smaller contact angle and larger airflow velocity lead to faster freezing and shorter final freezing time,which may provide a reference for in-depth studies on aircraft icing.
Experimental and numerical study on the impact and freezing process of a water droplet on a cold surface

Yina Yao,Cong Li,Zhenxiang Tao,Rui Yang,Hui Zhang

DOI: https://doi.org/10.1016/j.applthermaleng.2018.03.057

IF: 6.4

2018-01-01

Applied Thermal Engineering

Abstract:•The impact and freezing process of a water droplet on a cold plate were studied experimentally and numerically.•The effects of surface temperature on the dynamic and freezing mechanism of water droplets were investigated systematically.•A numerical model was developed to investigate the impact and freezing process of water droplets on ultra-cold surfaces.•The results provide an indication for engineers and scientists to develop efficient anti-icing methods.
A modeling study of sessile water droplet on the cold plate surface during freezing under natural convection with gravity effect considered

LU Menglong,Song Mengjie,MA Zhenjun,Wang Xiaotao,Zhang Long

DOI: https://doi.org/10.1016/j.ijmultiphaseflow.2021.103749

IF: 4.044

2021-10-01

International Journal of Multiphase Flow

Abstract:Freezing of water droplet is widely seen and important in the fields of aerospace, cold energy storage, and power production. To investigate the freezing process of a sessile water droplet on a horizontal cold plate, a theoretical model was developed. Different from previously reported models, the effects of supercooling and gravity on the physical properties and the water droplet profile are both considered, respectively. This model is validated with the experimental data of two parameters, including the freezing time and the freezing front radius. The results indicate that the deviation of freezing time is decreased from 7.69% to 0.17%, while the accuracy improved by 7.52%. The average deviation of the freezing front radius is decreased from 142.90 μm to 57.94 μm, with the accuracy improved by 59.46%. At the freezing stage, the appearance of the dynamic growth angle contributes to the less deviation of the freezing front radius. The eccentricity of droplet shape decreases from 0.45 to 0.03, with the eccentricity decreased by 93.45%. The temperature change rates inside a droplet show a gradually decreasing tendency, and the temperatures at different droplet locations present different limiting values. The findings of this study are beneficial for understanding droplet solidification process as well as new technologies for refrigeration, deicing, and defrosting.

mechanics
Investigation of the Freezing Process of Water Droplets Based on Average and Local Initial Ice Fraction

Yina Yao,Rui Yang,Cong Li,Zhenxiang Tao,Hui Zhang

DOI: https://doi.org/10.1080/08916152.2019.1600619

2019-01-01

Experimental Heat Transfer

Abstract:We presented both experimental and numerical studies on the freezing of impacting water droplets on a cold surface at different surface temperatures. The numerical model consists of two parts. The first one is to determine the temperature evolution of the droplet prior to the occurrence of freezing by solving the heat conduction equation, and the second one is to simulate the freezing process via an extended phase change model. Experiments were conducted to observe and record the freezing process. The droplet profile and the propagation of moving water-ice interface during freezing were obtained from image analysis. Based on the numerical pre-recalescence temperature of the droplet, the average initial ice fraction and local initial ice fraction were obtained. Then, both the two kinds of initial ice fractions were used to figure out the difference that they brought to the predicted freezing process. Through a comparison of the experimental observations and the numerical predictions, the freezing process predicted by using local initial ice fraction showed a better agreement with the experiment than using average initial ice fraction.
Droplet impact dynamics and heat transfer on nanostructured doubly reentrant cavity under freezing temperature

Dong Liao,Yinchuang Yang,Huihe Qiu

DOI: https://doi.org/10.1063/5.0050400

IF: 4.6

2021-05-01

Physics of Fluids

Abstract:Icephobic materials have wide applications for economic reasons as well as for risk reduction of ice accretion on an airframe. However, the mechanism behind the effect of structure parameters on droplet wetting dynamics and heat transfer on a doubly reentrant cavity is still elusive. This paper reports droplet impact dynamics and heat transfer on a set of doubly reentrant cavity surfaces by changing linewidth, microstructure height, and solid fraction under different surface temperatures and droplet impact velocities. It was found that the ratio of pitch distance and microstructure height is the most important parameter to control droplet dynamics and heat transfer. The surface with a small ratio (P/H < 1) of pitch distance (P) and microstructure height (H) has the best performance, which can successfully repel the droplet even when We = 1000 under −20 °C. The process of the liquid penetration was theoretically studied, and it was found that the temperature of the air inside largely increased due to droplet impact. The smaller the ratio, the higher the temperature increased. The increased air temperature restrains the ice nucleation rate and reduces the viscosity of water to make it easier to be drained out and therefore achieve icephobicity. When the kinetic energy of droplets is sufficient high, the compressed air temperature is so high that an expanding bubble will be generated at the center to make the liquid depart from the surface in a significantly shorter time named "doubly recoil" state, for the liquid in this state is recoiled from both inside and outside.

mechanics,physics, fluids & plasmas
Modeling study on sessile water droplet during freezing with the consideration of gravity, supercooling, and volume expansion effects

Menglong Lu,Mengjie Song,Xiaoling Pang,Chaobin Dang,Long Zhang

DOI: https://doi.org/10.1016/j.ijmultiphaseflow.2021.103909

IF: 4.044

2022-02-01

International Journal of Multiphase Flow

Abstract:Droplet freezing phenomenon widely exists in many fields, including aerospace, power production, and cryopreservation, etc. Considering the effects of supercooling, gravity and volume expansion, a theoretical model of droplet freezing is developed. A good agreement is found between the predicted results of freezing front radius and height and experiments for both hydrophilic and hydrophobic surfaces. The developed model also shows good performance in predicting freezing times. The average prediction deviation is 7.63%, and more than 93% simulation results show the deviation within ±15%. Gravity has a more obvious influence on final freezing times with the increase of cold plate temperature, contact angle, and droplet volume. For the droplet freezing process under various contact angles and cold plate temperatures, the fastest average temperature change rates inside water droplet are -2.48 °C/s and -1.72 °C/s, respectively. This study is beneficial for the better understanding of the droplet solidification as well as the optimization of refrigeration and defrosting technologies.

mechanics
Effect of nano-impurity on liquid/solid phase transition of water droplet

Meiyun Zhao,Yufan Xiong,Yuanyuan Shang,Xiang Xu

DOI: https://doi.org/10.1016/j.molliq.2024.124232

IF: 6

2024-02-23

Journal of Molecular Liquids

Abstract:The phenomenon of droplet freezing at low temperatures poses significant challenges in multiple domains, such as power transmission, communications, and aerospace. Impurities in the atmosphere have a complex impact on the process itself. The process of directly monitoring the production of crystal nuclei during the solidification of water poses substantial challenges, primarily attributed to factors such as the transparent nature of ice crystals and constraints inherent in experimental techniques. This study presents the development of a complete simulation system comprising substrates, nano-droplets, and impurities through the utilization of the molecular dynamics simulation method and LAMMPS simulation software. The process of icing is analyzed from microcosmic viewpoint for greater clarity. The process through which liquid droplets undergo ice formation is elucidated. A two-dimensional density curve was used to fit the contact angle of the nano-droplets. For droplets containing different quantity and distribution state of impurity, the beginning and the total freezing times are recorded. The findings indicate that the presence of impurity clusters have a substantial impact on the wettability of water droplets and the transition from the liquid to the solid phase. Furthermore, the results demonstrate that dispersed impurity clusters have excellent icing retardation properties. This study reveals a microscopic mechanism that may have implications for the use of impurity particles to directly achieve anti-icing functions in the atmosphere.

chemistry, physical,physics, atomic, molecular & chemical
Effects of surface temperature and Weber number on the dynamic and freezing behavior of impacting water droplets on a superhydrophobic ultra-cold surface

Yina Yao,Kewei Wu,Rui Yang,Hui Zhang,Wenjie Yang,Cong Li

DOI: https://doi.org/10.1016/j.applthermaleng.2023.121705

IF: 6.4

2023-10-02

Applied Thermal Engineering

Abstract:The dynamic and freezing behavior of a water droplet impacting a superhydrophobic cold surface is worthy of investigation. In this study, experiments are conducted to examine the impact and freezing of a water droplet on a cold superhydrophobic surface whose temperature changes in a wide range between −10 °C and −60 °C. A numerical model that introduces a continuous energy balance equation is developed to investigate the process numerically. The effects of surface temperature, Weber number, and initial droplet temperature on the droplet morphology, spread factor, contact time, and rebound height are investigated. The droplet exhibits three different behaviors as the surface temperature decreases: full rebound, partial rebound, and full adhesion. For the full rebound case, the results indicate that the growth rate of the contact time with decreasing surface temperature increases as the Weber number decreases. For the full adhesion case, the variation in the surface temperature minimally affects the dynamic behavior of the droplet impacting on an ultracold superhydrophobic surface (below −40 °C). The effect of surface temperature on the maximum spread factor is more pronounced at higher Weber numbers. Additionally, the ice nucleation rate is analyzed theoretically. The results show that the nucleation rate of droplets impacting an ultracold surface remains almost constant regardless of the surface temperature and surface roughness. Moreover, a regime map showing the different droplet morphologies correlating with the surface temperature and Weber number is established. The critical surface temperatures for different droplet morphologies of supercooled and room-temperature droplets are analyzed. This study allows us to better understand the dynamic and heat transfer mechanisms involved in the impact and freezing of a water droplet on a superhydrophobic surface.

energy & fuels,engineering, mechanical,thermodynamics,mechanics
Numerical investigation on the performance and anti-freezing design verification of atomization equipment in an icing cloud simulation system

Huanyu Deng,Shinan Chang,Mengjie Song

DOI: https://doi.org/10.1007/s10973-019-09046-2

IF: 4.755

2019-11-21

Journal of Thermal Analysis and Calorimetry

Abstract:Aircraft icing occurs when flying through the cloud containing supercooled water droplets or ice crystals, posing a threat to flight safety. To simulate the natural icing environment, a climatic environmental test facility was designed, in which atomization equipment was utilized to spray micro-sized water droplets. To optimize and provide a reference design for the atomization equipment, a numerical study on its performance and anti-freezing design verification was carried out. The developed model was successfully validated with the maximum experimental ice thickness and its outlined shape on the test rod, with the error of maximum ice thickness at only 2.6%. The maximum deviation and mean deviation are at 1.13 mm and 0.68 mm, respectively. Freeze protection was finally enabled by ensuring the supplement temperature of the water, as well as the air in pipes, higher than 28.85 °C. Results suggested the best position for the test, at 2 m upstream of the nozzle outlet. The water flow temperature at the nozzle outlet was 29.45 °C higher than the freezing point. As a validated and applicable method, this study shows its novelty and practical value in the development of the climatic environmental test facility.

chemistry, physical, analytical,thermodynamics
Freezing of a Supercooled Water Drop after an Impact onto a Solid Wall

Mingyue Ding,Jeanette Hussong,Ilia V. Roisman

DOI: https://doi.org/10.1016/j.coldregions.2024.104359

IF: 4.427

2024-11-10

Cold Regions Science and Technology

Abstract:Supercooled water freezes as a result of ice nucleation, propagation along the substrate of a thin ice layer and subsequent expansion of a mushy region of ice dendrites. In this experimental study, the impact, spreading and solidification of the drop are observed in a cold wind tunnel using a high-speed video system. The statistics of the nucleation times after a supercooled water drop impacts onto a dry solid substrate are analyzed. The experiments demonstrate that the rate of the ice nucleation is enhanced significantly by drop impact and continuously reduces over time. The nucleation rate increases with higher impact velocity and is enhanced by the substrate roughness. This effect is explained by the presence of the small bubbles in the liquid drops, generated by drop impact and fast spreading. The surfaces of these bubbles serve as the additional triggers for ice nucleation. Moreover, the effect of the presence of the bubbles becomes even more significant when the wetted area reduces due to the drop receding. The average number of the nucleation sites in this case increases, since the number of bubbles does not reduce despite the reductions of the wetted area. These bubbles are probably captured by the receding contact line.

engineering, environmental, civil,geosciences, multidisciplinary
Effect of temperature difference between Impinging Droplet and Cold Superhydrophobic Surface on Its Dynamic Behavior

Hailing Yu,Xin Zhou,Hong Wang,Qian Zhang,Xun Zhu,Yu Dong Ding,Rong Chen,Qiang Liao

DOI: https://doi.org/10.1016/j.expthermflusci.2023.111049

IF: 3.2

2023-09-02

Experimental Thermal and Fluid Science

Abstract:The phenomenon of water droplets impacting on cold surfaces and freezing is common in various fields and has numerous detrimental effects. Meanwhile, superhydrophobic surfaces have received a lot of attention in terms of preventing icing. Therefore, it is important to investigate the dynamic behavior of water droplets impacting on superhydrophobic surfaces in a supercooled environment under different temperature conditions in order to prevent icing. In this study, the dynamic behavior of water droplets impacting on superhydrophobic surfaces in a supercooled environment is visualized using a high-speed camera, and the effect of the temperature difference between the droplet and the cold surface on the dynamic behavior of the impacting droplet is emphatically investigated. The dynamic characteristics of the droplet were also analysed in terms of dimensionless contact diameter, dimensionless droplet height, contact time and energy balance. The results show that the change in properties of the droplet is mainly reflected in the change in viscosity. At low Weber number, the change in viscosity has little effect on the dimensionless contact diameter and contact time but has a significant effect on the dimensionless height of the droplet during retraction. Of particular note is the fact that when the droplet temperature is constant, a decrease in the surface temperature leads to a significant slowing down of the droplet retraction process on the superhydrophobic surface and a significant increase in the contact time. However, a phenomenon contrary to intuition has been observed, namely that a similar situation occurs with increasing droplet temperature when the surface temperature is constant. This behaviour of the droplets is related to the possible existence of liquid-phase condensation processes in the microstructure, and we have also analysed theoretically the conditions under which condensation occurs. This study could contribute to the development of anti-icing technology.

engineering, mechanical,thermodynamics,physics, fluids & plasmas
How Different Freezing Morphologies of Impacting Droplets Form.

Wen-Zhen Fang,Fangqi Zhu,Wen-Quan Tao,Chun Yang

DOI: https://doi.org/10.1016/j.jcis.2020.09.119

IF: 9.9

2020-01-01

Journal of Colloid and Interface Science

Abstract:Hypothesis: Freezing morphologies of impacting water droplets depend on the interaction between droplet spreading and solidification. The existing studies showed that the shape of frozen droplets mostly is of spherical cap with a singular tip, because of much shorter timescale of the droplet spreading than that of the solidification. Here, we create the experimental conditions of extended droplet spreading and greatly enhanced heat transfer for fast solidification, thereby allowing to study such droplet freezing process under the strong coupling of the droplet spreading and solidification. Experiments: We design experiments that a room-temperature water droplet impacts on a subcooled superhydrophilic surface in an enclosure chamber filled with nitrogen gas. We thoroughly investigate the freezing processes of impacting droplets under the effects of impact velocity and substrate temperature. Both the droplet impact dynamics and solidification are studied with a high-speed camera. Findings: We observed five different freezing morphologies which depend on the droplet impact velocity and substrate temperature. We found that the formation of diverse morphologies results from the competitive timescales related to droplet solidification and impact hydrodynamics. We also develop a phase diagram based on scaling analysis and show how freezing morphologies are controlled by droplet impact and freezing related timescales. (C) 2020 Elsevier Inc. All rights reserved.
Experimental Investigation and Statistical Analysis of Icing Nucleation Characteristics of Sessile Water Droplets

Xuan Zhang,Xin Liu,Xiaomin Wu,Jingchun Min

DOI: https://doi.org/10.1016/j.expthermflusci.2018.07.027

IF: 3.2

2018-01-01

Experimental Thermal and Fluid Science

Abstract:Nucleation and freezing of water droplet are very common in aerospace, power, meteorology and refrigeration. This study experimentally investigates the nucleation temperatures of sessile water droplets with volumes of 1, 5 and 10 mu L on a cold horizontal aluminum plate which greatly influence the droplet freezing process. Analyses are made on the droplet nucleation sequence and nucleation temperature series as well as their correlations to estimate the systematic errors in the nucleation data, and the results support that such errors are negligibly small. The nucleation temperatures are further analyzed statistically to obtain their average value, standard deviation, frequency distribution and cumulative distribution. The nucleation results for different droplet volumes indicate that a smaller droplet has a lower average nucleation temperature and a larger standard deviation (wider frequency distribution). The nucleation rates are fitted using the classical nucleation theory. The results show that the nucleation rate increases as the temperature decreases and the droplet volume increases. The nucleation time, which involves transient nucleation and is often used to evaluate the surface anti-icing/frosting characteristics, is measured experimentally at a constant plate temperature. The nucleation rate for transient nucleation is found to increase with time. A higher temperature yields larger minimum, average, and maximum nucleation times but a lower nucleation rate. These results provide guidance for predicting ice/frost accretion on surfaces and for designing anti-icing/frosting surfaces.
Simulation and Experiment on Supercooled Sessile Water Droplet Freezing with Special Attention to Supercooling and Volume Expansion Effects

Xuan Zhang,Xin Liu,Xiaomin Wu,Jingchun Min

DOI: https://doi.org/10.1016/j.ijheatmasstransfer.2018.07.021

IF: 5.2

2018-01-01

International Journal of Heat and Mass Transfer

Abstract:The freezing process of supercooled water droplets on cold plates is studied experimentally and numerically. A numerical model that considers both the supercooling effect on the physical properties and the volume expansion effect on the droplet freezing profile is established to simulate the droplet freezing behaviors using the Solidification/Melting model. Experiments are conducted on both hydrophilic and hydrophobic surfaces for 5, 10, 20, 30 and 40 pi supercooled water droplets. The droplet freezing behaviors including the freezing front movement and freezing time are observed using the image recognition technology. The evolution of the freezing front calculated by the numerical model agrees better with the experimental observation than the traditional model that ignores the supercooling effect or uses the initial droplet profile. The model reduces the deviation of freezing time from about 30% to about 10% for both hydrophilic and hydrophobic surfaces. With use of the average value of the freezing times yielded by the numerical and theoretical models, a correlation is developed for predicting the freezing time. It can correlate more than 90% of the simulation data and all of the experimental points within 25%. As the cold plate temperature, droplet volume and contact angle increase, the freezing time increases, with the plate temperature and contact angle possessing a more significant influence than the droplet volume on the freezing process. (C) 2018 Elsevier Ltd. All rights reserved.
Supercooled water droplet impacting-freezing behaviors on cold superhydrophobic spheres

Xin Liu,Jingchun Min,Xuan Zhang,Zhifeng Hu,Xiaomin Wu

DOI: https://doi.org/10.1016/j.ijmultiphaseflow.2021.103675

IF: 4.044

2021-08-01

International Journal of Multiphase Flow

Abstract:The impacting-freezing behaviors of supercooled water droplets on superhydrophobic spheres are investigated. A numerical model using the VOF (Volume of Fluid) method and enthalpy–porosity technology is established and validated by comparing the droplet profiles and spreading area factors by simulations and experiments. The effects of Weber number, supercooling degree and sphere-to-droplet diameter ratio (D*) on the impacting-freezing dynamics, including the droplet profile, spreading area factor and final rebound/adhesion, are studied. The results indicate that the supercooling rarely influences the spreading stage but significantly affects the receding stage with a larger stable spreading area factor obtained at a greater supercooling degree. With the decreasing of diameter ratio, the droplet generates a larger maximum spreading arc angle, a higher receding speed and thus a shorter contact time. The maximum spreading area factor greatly increases with reducing diameter ratio for D*<10 but it remains almost unchanged for D*≥10. Three different final morphologies of full rebound, partial rebound and adhesion are obtained, revealing the competition between the fluid flow and phase change in the droplet impacting-freezing process. The morphology map of rebound and adhesion indicates that the boundaries for droplet rebound and adhesion initially move to a smaller supercooling degree and then revert to the previous value as the diameter ratio becomes smaller. The findings in this research may deepen our understanding of the mechanism of supercooled water droplet impacting and freezing on a superhydrophobic curved surface, and contribute to the design of anti-icing/frosting surface.

mechanics
Supercooled Water Droplet Impact on Superhydrophobic Surfaces with Various Roughness and Temperature

Rui Zhang,Pengfei Hao,Xiwen Zhang,Feng He

DOI: https://doi.org/10.1016/j.ijheatmasstransfer.2018.01.076

IF: 5.2

2018-01-01

International Journal of Heat and Mass Transfer

Abstract:This paper investigates the impact behaviors between supercooled droplets and various superhydrophobic surfaces. We analyze the thermodynamic reason of the liquid adhesion at low temperature and discuss the influence of the substrate roughness, temperature and wetting property on the impact dynamics of supercooled droplets both experimentally and theoretically. The liquid adhesion results from the ice nucleation rather than the enhanced viscous effect induced by the low temperature. The dramatic increase of the liquid-solid contact area induced by the high-speed collisions between droplets and textured surfaces leads to a larger nucleation rate and a lower critical adhesion temperature. The analytical argument of the liquid-solid contact area fraction at different impact speed throws light on the understanding of the controversy if hierarchical superhydrophobic surfaces are icephobic at low temperature. Valuable suggestions are given that smooth superhydrophobic surfaces with nanoscale roughness near the critical nucleus radius perform better water-repellency against high-speed supercooled droplets. (C) 2018 Elsevier Ltd. All rights reserved.
Anti-freezing Characteristics of Water Droplet Impinging the Superhydrophobic Surface: an Experimental and Predictive Study

Xin Wang,Zhiwen Tang,Bo Xu,Zhenqian Chen

DOI: https://doi.org/10.1016/j.apsusc.2021.150717

IF: 6.7

2021-01-01

Applied Surface Science

Abstract:Water freezing has a significant and non-negligible influence on the aircraft, power transmission lines and operational efficiency of industrial facilities. Therefore, it is of great value and meaning to deeply understand the dynamic behaviors of water droplet impacting the supercooled superhydrophobic surface. In this work, effects of impact velocity, surface temperature and inclined angle on the impinging droplet dynamics are visually investigated. The machine learning model is first proposed to predict the rebound height and temperature limit of fully rebound. The results demonstrate that a larger impact velocity shifts the temperature limit of completely rebound to a higher surface temperature. However, it has little effect on the spreading time and contact time. As the temperature further decreases, portion of droplet is pinned on the substrate instead of fully rebound and the volume of residual droplet increases. As the inclined angle increases, both contact time and rebound height decreases. Due to driven by the tangential component of gravity, width of droplet before detachment increases while the stretched length decreases. The optimal temperature limit of fully rebound is -35 degrees C with the inclined angle of 30 degrees and We = 19, showing a significant improvement compared to the temperature limit on a horizontal surface.
Frost Layer Growth Behavior Study on a Cryogenic Surface with Water Vapor Content <1000 Ppmv

Yinghe Qi,Hengyang Ye,Wenhan Shu,Xiaoqin Zhi,Limin Qiu

DOI: https://doi.org/10.1016/j.icheatmasstransfer.2023.107027

IF: 6.782

2023-01-01

International Communications in Heat and Mass Transfer

Abstract:Frosting under cryogenic conditions is common in liquefied natural gas (LNG), cryogenic containers, cryogenic wind tunnels, cryopump and other engineering fields, but the corresponding researches are still insufficient compared with that under general-low temperature conditions. Especially, research on extra-low-content water vapor frosting under cryogenic conditions stays almost blank. A visualization experiment system was built, based on which cryogenic frosting experiments of water-vapor-carrying nitrogen gas flow with different water vapor contents (120 ppmv ≤ ωin ≤ 780 ppmv) considering the cooling process (from 290 K to 100 K) were carried out. Images through the whole frosting period were recorded and image processing was executed. The evolution of the frost surface was captured and the translation velocity was calculated. Physical properties of the frost layer including thickness (as large as 1.75 mm at 2 h) and roughness (up to 76.2 μm) were obtained and compared with humid air frosting. The frost layer growth pattern transition from needle-like vertical growth to clump-grass-like circular rotational growth was observed in the rapid cooling stage. The results reveal differences in frost formation mechanisms and characteristics from general-low to cryogenic temperatures and can provide a quantitative reference for mass and heat transfer analysis in practical frosting circumstances.

Influence of pre-fermentative treatment on the fatty acid content of Saccharomyces cerevisiae (M(3)30-9) during alcoholic fermentation of grape must.

Experimental Research on Low Supercooling of Ice Storage and Analysis of Its Energy Saving

Effect of Liquid Nitrogen Spray Freezing on the Ice Crystal Size and Quality of Large Yellow Croaker

Numerical Simulation of Freezing Process of a Sessile Supercooled Water Droplet on a Cold Wall

Experimental and numerical study on the impact and freezing process of a water droplet on a cold surface

A modeling study of sessile water droplet on the cold plate surface during freezing under natural convection with gravity effect considered

Investigation of the Freezing Process of Water Droplets Based on Average and Local Initial Ice Fraction

Droplet impact dynamics and heat transfer on nanostructured doubly reentrant cavity under freezing temperature

Modeling study on sessile water droplet during freezing with the consideration of gravity, supercooling, and volume expansion effects

Effect of nano-impurity on liquid/solid phase transition of water droplet

Effects of surface temperature and Weber number on the dynamic and freezing behavior of impacting water droplets on a superhydrophobic ultra-cold surface

Numerical investigation on the performance and anti-freezing design verification of atomization equipment in an icing cloud simulation system

Freezing of a Supercooled Water Drop after an Impact onto a Solid Wall

Effect of temperature difference between Impinging Droplet and Cold Superhydrophobic Surface on Its Dynamic Behavior

How Different Freezing Morphologies of Impacting Droplets Form.

Experimental Investigation and Statistical Analysis of Icing Nucleation Characteristics of Sessile Water Droplets

Simulation and Experiment on Supercooled Sessile Water Droplet Freezing with Special Attention to Supercooling and Volume Expansion Effects

Supercooled water droplet impacting-freezing behaviors on cold superhydrophobic spheres

Supercooled Water Droplet Impact on Superhydrophobic Surfaces with Various Roughness and Temperature

Anti-freezing Characteristics of Water Droplet Impinging the Superhydrophobic Surface: an Experimental and Predictive Study

Frost Layer Growth Behavior Study on a Cryogenic Surface with Water Vapor Content &lt;1000 Ppmv

Frost Layer Growth Behavior Study on a Cryogenic Surface with Water Vapor Content <1000 Ppmv