Abstract:As the demand for energy increases, competition for a sustainable alternative to non-renewable energy resources has resulted in the growth of the photovoltaic industry. Although most photovoltaic technologies are based on crystalline silicon, thin film technologies have been developed with the expectation of generating a comparably high-performing product with lower processing costs. These materials have demonstrated sufficiently high optoelectronic performance to enable commercialization but concerns such as material scarcity limit terawatt level power production.In the continuous pursuit of earth abundant solar absorber materials appropriate for thin film technologies, enargite Cu3AsS4 has been identified as a promising material due to its ideal direct band gap, stability, and high absorption. Recent efforts have demonstrated this class of copper chalcogenides exhibits band gap tunability and has solution processing capabilities for potentially scalable manufacturing. Furthermore, recent first-principles calculations of enargite Cu3AsS4 have hypothesized this material may have high carrier mobility and defect-tolerant optoelectronic properties, which further support investigation into this material. In this dissertation, a novel reactive deposition processing route has been developed which has produced dense, single-phase enargite thin films. A champion device efficiency of 0.54% was achieved following a post deposition etching procedure on these films, which demonstrates the density and observable secondary phases were not limiting to initial nanoparticle-based device performances. Together with recent modeling efforts, the non-ideal band alignment with both the back contact and diode junction is concluded to be the primary limiting factor for high efficiency devices. As this technology contains arsenic, concerns have been raised about its potential carcinogenicity and toxicity. Similar concerns were raised during the development of cadmium telluride technology, but these concerns have been mitigated through careful life cycle analyses and identifying strategies for responsible life cycle management. Therefore, a life cycle analysis and two risk assessments have been completed on Cu3AsS4 systems. Although emissions of arsenic and its contributions to life cycle impacts are expected to be low due to the small quantity required, hot spots have been identified to reduce waste and emissions. Reduction strategies for this material system are found to be applicable to other PV systems and include minimizing molybdenum sputter waste, reusing and recycling balance of system components, and investigating low-energy processing routes on thin substrates. This work serves to establish a basis on which the potential environmental implications of this thin film technology are understood. This dissertation will serve as a guide toward the technical and environmental development of Cu3AsS4 thin films. Having a life cycle perspective during the systematic development of a technology will enable sustainable engineering. Furthermore, the processing and characterization methods detailed herein are expected to be generally applicable to other copper chalcogenide systems.

A prospective ecological risk assessment of high-efficiency III-V/silicon tandem solar cells

Sustainability of photovoltaic technologies in future net‐zero emissions scenarios

Cost versus environment? Combined life cycle, techno‐economic, and circularity assessment of silicon‐ and perovskite‐based photovoltaic systems

Ecotoxicity and Sustainability of Emerging Pb‐Based Photovoltaics

Analogical environmental cost assessment of silicon flows used in solar panels by the US and China

Environmental and health risks of perovskite solar modules: Case for better test standards and risk mitigation solutions

Photovoltaic panel waste assessment and embodied material flows in China, 2000-2050

Life-cycle human- and eco-toxicity assessment of emerging lead-based perovskite compared to conventional photovoltaic panels

A novel policy to tackle life span reassessment of existing bulk and thin-film photovoltaic materials

Comparing Environmental Impacts of Single-Junction Silicon and Silicon/Perovskite Tandem Photovoltaics-A Prospective Life Cycle Assessment

Life-cycle environmental impacts of single-junction and tandem perovskite PVs: a critical review and future perspectives

Scenario-based recycling strategies for perovskite-silicon tandem solar cells: a harmonized life cycle assessment study

Screening for sustainable and lead-free perovskite halide absorbers – A database collecting insight from electronic-structure calculations

Environmental Assessment of Solar Cell Materials

Dynamic criticality of by-products used in thin-film photovoltaic technologies by 2050

Synthesis and Environmental Assessment of Arsenic-Containing Copper Chalcogenides for Photovoltaic Applications

A review on life cycle environmental impacts of emerging solar cells

Bypassing the single junction limit with advanced photovoltaic architectures

Assessment of toxicity tests for photovoltaic panels: a review

Environmental impact of metal halide perovskite solar cells and potential mitigation strategies: A critical review

A review of toxicity assessment procedures of solar photovoltaic modules