Abstract:The investigation concentrates on friction stir welded (FSW) Al–Cu–Li alloy concerning its local microstructural evolution and mechanical properties. The grain features were characterized by electron back scattered diffraction (EBSD) technology, while precipitate characterization was conducted by using transmission electron microscopy (TEM) aligned along [011] Al and [001] Al zone axes. The mechanical properties are evaluated through micro-hardness and tensile testing. It can be found that nugget zones exhibit finely equiaxed grains evolved through complete dynamic recrystallization (DRX), primarily occurring in continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX). In the thermal–mechanically affected zone (TMAZ), numerous sub-structured grains, exhibiting an elongated morphology, were created due to partial DRX, signifying the dominance of CDRX, DDRX, and geometric dynamic recrystallization (GDRX) in this region. T 1 completely dissolves in the nugget zone (NZ) leading to the formation of Guinier–Preston zones and increase of δ′, β′ and S′. Conversely, T 1 partially solubilizes in TMAZ, the lowest hardness zone (LHZ) and heat affected zone (HAZ), and the residual T 1 undergoes marked coarsening, revealing various T 1 variants. The solubilization and coarsening of T 1 are primary contributors to the degradation of hardness and strength. θ′ primarily dissolves and coarsens in NZ and TMAZ, whilst this precipitate largely coarsens in HAZ and LHZ. σ, T B , grain boundary phases (GBPs) and precipitate-free zone (PFZ) are newly generated during FSW. σ exists in the TMAZ, LHZ and HAZ, whereas T B nucleates in NZ. GBPs and PFZ mostly develop in LHZ and HAZ, which can cause strain localization during tensile deformation, potentially leading to LHZ joint fracture.

Correlation of local microstructures and mechanical properties of Al–Zn–Mg–Cu alloy build fabricated via underwater friction stir additive manufacturing

Effect of Post-Fabricated Aging on Microstructure and Mechanical Properties in Underwater Friction Stir Additive Manufacturing of Al–Zn–Mg–Cu Alloy

Restirring and Reheating Effects on Microstructural Evolution of Al–Zn–Mg–Cu Alloy during Underwater Friction Stir Additive Manufacturing

Investigation on microstructural evolution and property variation along building direction in friction stir additive manufactured Al–Zn–Mg alloy

Local Microstructure Evolution and Mechanical Performance of Friction Stir Additive Manufactured 2195 Al-Li Alloy

Microstructure evolution and mechanical properties of wire-arc additive manufactured Al–Zn–Mg–Cu alloy assisted by interlayer friction stir processing

Microstructure Evolution and Mechanical Properties of Ultrafine-Grained AlLi Alloy Fabricated Via Friction Stir Additive Manufacturing

High Speed Friction Stir Welding of Ultra-Thin AA6061-T6 Sheets Using Different Backing Plates

Evolution of microstructure and properties in 2219 aluminum alloy produced by wire arc additive manufacturing assisted by interlayer friction stir processing

Microstructure evolution and enhanced mechanical properties of additive manufacturing Al-Zn-Mg-Li alloy via forging and aging treatment

High-efficient hybrid arc and friction stir additive manufacturing of high-performance Al-Cu-Mg-Ag-Zr alloy: Microstructural evolution and precipitation behaviors with Ω/L1 2 co-precipitates

High-efficient Hybrid Arc and Friction Stir Additive Manufacturing of High-Performance Al-Cu-Mg-Ag-Zr Alloy: Microstructural Evolution and Precipitation Behaviors with Ω/L12 Co-Precipitates

Microstructure and Properties of Solid-State Additive Manufactured Mg–10Li–3Al–3Zn Magnesium Alloy

Microstructural Characterization and Mechanical Properties of AlMg Alloy Fabricated by Additive Friction Stir Deposition

Quantitative study on the correlation between microstructure and mechanical properties of additive friction stir deposited

Investigation of microstructure and properties in an aged ultra-high strength Al alloy and its friction stir welded joints

Microstructure Evolution and Strengthening Mechanisms of an Additive Friction Stir Deposited Multi-Layer Al-Mg-Sc-Zr Alloy

Refined microstructure and enhanced mechanical performance of hybrid additive manufacturing Al-Cu-Mg alloys by multi-cycle friction stirring processing

Microstructure and Mechanical Properties of Al–Li Alloy Manufactured by Additive Friction Stir Deposition

Investigation the effects of friction stir processing on microstructure and mechanical properties of Al–Cu alloy fabricated by wire arc additive manufacturing

Microstructure Evolution and Mechanical Properties of Friction Stir Welded Al–Cu–Li Alloy