An integrative approach to quality assurance.

T. Smith,B. Powers

1990-06-01

Nursing Management

Abstract:

What problem does this paper attempt to address?

Enhancing radiation shielding effectiveness: a comparative study of barium-doped tellurite glasses for gamma and neutron radiation protection

Ali H. Alomari

DOI: https://doi.org/10.1080/16583655.2024.2328370

2024-03-13

Journal of Taibah University for Science

Abstract:This study investigated the radiation shielding performance of the xBaO-(30-x)TeO 2 -35Bi 2 O 3 -35B 2 O 3 glass system, where x = 5, 10, 15, 20 and 25, using Phy-X/PSD software and MCNPX Monte Carlo code. Key radiation shielding indicators, including attenuation coefficients, half value layer (HVL), tenth value layer (TVL), effective atomic number (Z eff ), mean free path (MFP), and build-up factors, were measured within the energy range of 0.015–15 MeV. Further, the study assessed the glasses' capacity to block fast neutrons, using the fast neutron removal cross-section (ΣR) as a metric. The results showed that gamma shielding effectiveness follows the order: BaTBiB-1 < BaTBiB-2 < BaTBiB-3 < BaTBiB-4 < BaTBiB-5 at all photon energies. Additionally, the ΣR values for BaTBiB-1 to BaTBiB-5 glasses were 0.10179, 0.10263, 0.10362, 0.10581, and 0.10623 cm −1 , respectively. Therefore, the findings demonstrate that including BaO enhances the gamma and neutron shielding characteristics of tellurite glasses, making them valuable for radiation-related applications.

multidisciplinary sciences
Highly transparent glass of barium-reinforced borotellurite as a protective material from gamma rays

Wadha Alyami,Sara A. El-khateeb,Essam M. Alkhybari,Layal K. Jambi,Ibrahim E. Saad

DOI: https://doi.org/10.1007/s11082-023-06216-3

IF: 3

2024-02-02

Optical and Quantum Electronics

Abstract:A series of barium borotellurite glass networks (BT-Ba) were produced to study their effectiveness in attenuating gamma rays at different energies and fast neutrons. A host borotellurite glass network of the composition 25TeO 2 -25B 2 O 3 -10CaO-10ZnO-30Na 2 O (BT) was proposed and reinforced with 10, 20, and 30 mol% of BaO (BTBa1, BTBa2, and BTBa3) at the expense of Na 2 O. The proposed BT-Ba glasses were produced using the melting/annealing method. The structural properties of the studied BT-Ba glass network were examined using X-ray diffraction (XRD), density and density-based parameters, and Fourier transform infrared (FTIR) spectra. These studies revealed the ability of BaO to enhance the amorphous phase of the studied borotellurite glass network and enrich it with non-bridging oxygen units (NBOs) through the conversion of the bridging ones (BOs). The visible light transparency of the produced BT-Ba glass series was examined by recording the optical transmittance spectra in the UV–visible light regions. Using EpiXS software, the gamma ray attenuation ability of the studied BT-Ba glasses was examined at different gamma ray energies of 302.851, 383.849, 661.657, 1173.228, 1332.492, 1408.013, and 1528.1 keV. While the fast neutron removal cross section was estimated according to the standard mixture rule. The dependence of the behavior of the mass and linear attenuation coefficients, half-value layer, effective atomic number, and effective electron density on BaO concentrations was extensively investigated to explore the attenuation ability of the studied glasses. Among the studied glasses, BT, BTBa1, BTBa2, and BTBa3, the fabricated glass BTBa3 had high transparency (more than 82%) and reduced the required half-value layer from 1.552 to 3.688 cm of BT to 1.041–2.965 cm for the studied gamma ray energies. On the other hand, a slight improvement in fast neutron attenuation with increasing BaO concentrations was observed. The BTBa3 glass had the highest fast neutron cross-section of 0.104 cm −1 . Hence, the BTBa3 glass is considered effective as a protective glass for gamma rays and fast neutrons, opening horizons for it in nuclear applications.

engineering, electrical & electronic,optics,quantum science & technology
Designing High-Density of PbO-Enriched Telluro-Borate Glasses for Improved Radiation Shielding: A Comprehensive Study of Attenuation Parameters

Hammam Abdurabu Thabit,Abd Khamim Ismail,Suhairul Hashim,M.I. I Sayyed,K.A. Naseer,S.A. Bassam

DOI: https://doi.org/10.1149/2162-8777/ad06e5

IF: 2.2

2023-10-27

ECS Journal of Solid State Science and Technology

Abstract:Several radiation shielding parameters for (75-x)B2O3-10TeO2-13SrCO3 -2ZnO-xPbO glasses were evaluated between 0.284 and 1.333 MeV. The PbO content in the glass has a positive relationship with the density of the glasses, leading to BTSZP0, the glass with no PbO, having the smallest density, while BTSZP5, which has 40 PbO mol%, has the greatest density. Radiation shielding parameters such as mass attenuation coefficients and other related factors were computed, and relationships between PbO content, energy, and density are graphed. Linear attenuation coefficient (LAC) is reported and we evaluated the impact of density on the LAC values. By adding more PbO atoms, the density of the samples increased, leading to a higher LAC. The BTSZP0 sample has the highest HVL at all tested energies, with the BTSZP5 sample having the lowest HVL. Mean free path (MFP) has an inverse relationship with the density of each sample but increases with greater incoming photon energy. The effective atomic number (Zeff) values peak at low photon energies and rise significantly with increasing PbO content. The MFP and TVL of the BTSZP glasses are compared against previously tested glass samples at a set energy, and the values demosntrated the effectiveness of the BTSZP glasses.

materials science, multidisciplinary,physics, applied
Optical properties and radiation shielding competence of Bi/Te-BGe glass system containing B2O3 and GeO2

M.S Al-Buriahi,Z.A. Alrowaili,I.O. Olarinoye,Chalermpon Mutuwong,Sultan Alomairy

DOI: https://doi.org/10.1016/j.ijleo.2022.168883

IF: 3.1

2022-05-01

Optik

Abstract:In this study we present the optical features including several parameters, gamma-ray photon and fast neutron absorption parameters of quaternary glasses with the chemical structure: xBi2O3 + (80-x)TeO2 + 10B2O3 + 10GeO2 for x = 40, 50, and 60 mol% and coded as Bi/Te-BGe1, Bi/Te-BGe2, and Bi/Te-BGe3 respectively. The FLUKA Monte Carlo and XCOM code were used to evaluate the photon shielding parameters of the glasses for energies between 0.284 and 2.506 MeV. The optical quantities such as the molar refractivity R m , molar polarizability α mol , reflectance loss ( R loss ) , optical transmission ( T opt ) , metallization criterion (M) and the static dielectric constant ε sta of the glasses were estimated to understand their optical characteristic. Mass attenuation coefficient of 0.345, 0.368, and 0.386 cm2/g was obtained for Bi/Te-BGe1–3 respectively at 0.284 MeV. Evaluated Z eff ranged from 30.94 to 53.22, 32.73 – 56.29, 34.52 – 58.75 for the Bi/Te-BGe1–3 glasses respectively. The HVL within the investigated energy similar to other estimated photon shielding parameters showed great enhancement as the density and Bi2O3 content of the glasses improved. Similar improvement on the fast neutron removal cross section also increased from 0.1141 to 0.1178 cm−1 as bismuth oxide increases in the glass system. The estimated optical parameters also showed great dependence on the chemical structure of the glasses. The present Bi/Te-BGe1–3 glasses showed excellent fast neutron and photon absorption capacity compared to some common shields; this makes them potentially useful for radiation protection applications.

optics
Radiation shielding performance of tellurium–thallium and tellurium–lead oxide glass systems

N. Khan,G. Rooh,S. Mukamil,S.A. Khattak,M. Shoaib,I. Khan,I. Ullah,T. Ahmad,S.K. Shah,K. Safeen,M. Shoaib

DOI: https://doi.org/10.1016/j.radphyschem.2024.111517

IF: 2.776

2024-01-21

Radiation Physics and Chemistry

Abstract:In this study, TeO 2 –Tl 2 O and TeO 2 –PbO glasses with various compositions were investigated for γ-ray shielding using Phy-X and MCNPX Code. A comparative analysis of the obtained results were performed. The effective atomic number and various parameters, including the mean free path, mass attenuation coefficient, linear attenuation coefficient, and half value layer, were determined in the energy range of 0.01 MeV–15 MeV. It was found that 90TeO 2 –10Tl 2 O glass exhibit the lowest linear attenuation coefficient among the studied samples. At 60 keV, the 82TeO 2 –18Tl 2 O and 90TeO 2 –10Tl 2 O glasses had half-values of T 1/2 = 0.00094 cm and 0.00105 cm, respectively. At 100 keV, the mean free path of the examined materials is estimated to be 0.004 cm and 0.005 cm. The rise in effective atomic number was explained as a greater number of electrons available for photon interaction, which led to a lower chance of γ-ray transit through the shielding material. These results collectively underscore the potential of these glass compositions, particularly those containing thallium to be use as effective shielding materials. These materials have growing importance of effective radiation protection in various fields, including medical imaging, nuclear power, and space exploration.

chemistry, physical,physics, atomic, molecular & chemical,nuclear science & technology
New transparent rare earth glasses for radiation protection applications

M. S. Al-Buriahi,H. O. Tekin,Esra Kavaz,Baris T. Tonguc,Y. S. Rammah

DOI: https://doi.org/10.1007/s00339-019-3077-8

2019-11-26

Applied Physics A

Abstract:In this paper, we have reported $65\hbox {B}_2\hbox {O}_3$–$12.5\hbox {TeO}_2$–$12.5\hbox {Bi}_2\hbox {O}_3$–$5\hbox {Na}_2\hbox {O}$–$5\hbox {NdCl}_3$ and $67\hbox {TeO}_2$–$20\hbox {WO}_3$–$10\hbox {Li}_2\hbox {O}$–$3\hbox {PrO}_{11}$ glasses to serve in radiation protection applications. Mass attenuation coefficient ($\mu /\rho$) of the proposed glasses was obtained in the photon energy range of 0.015–15 MeV using GEANT4 Monte Carlo simulation. The simulation results were compared with those calculated by WinXCOM program. The correlation factor (${R}^2$) between the simulation and the theoretical values was found to be close to one referring to the high accuracy of the present results. Other essential radiation shielding parameters such as the effective atomic number (${Z}_\mathrm{eff}$), half-value layer, and neutron removal cross section ($\sum _R$) were calculated for the proposed glass samples. Additionally, G-P method was used to generate exposure buildup factor and energy absorption buildup factor for each proposed glass in the photon energy range of 0.015–15 MeV up to penetration path of 40 mfp. Radiation shielding competence of our glasses was compared with conventional shielding materials, other rare earth glasses, and newly developed HMO glasses. The results reveal that our proposed glass coded as TWLP shows promising shielding competence against both gamma rays and neutrons.
Impact of Modifier Oxides on Mechanical and Radiation Shielding Properties of B2O3-SrO-TeO2-RO Glasses (Where RO = TiO2, ZnO, BaO, and PbO)

M. I. Sayyed,M. Kh. Hamad,Mohammad Hasan Abu Mhareb,K. A. Naseer,K. A. Mahmoud,Mayeen Uddin Khandaker,Hamid Osman,Basem H. Elesawy

DOI: https://doi.org/10.3390/app112210904

2021-11-18

Applied Sciences

Abstract:The influence of modifier oxides (TiO2, ZnO, BaO, and PbO) on the mechanical and radiation shielding properties of boro-tellurate glasses is investigated. Samples with a composition of B2O3-SrO-TeO2-RO (RO represents the modifier oxides) were fabricated using the melt quench method, and their physical, mechanical, and radiation attenuation parameters were reported. For this aim, Monte Carlo simulation was employed to predict the radiation attenuation parameters, while the Makishima-Mackenzie model was adopted to determine the mechanical properties. The tightly packed structure with better cross-linkage density is possessed by the Ti-containing glass (SBT-Ti) system among the titled glass batch. The higher Poisson and micro-hardness values of the SBT-Ti glass indicate its structure’s reduced free volume and better compactness. For the glass with PbO, the linear and mass attenuation coefficients are highly increased compared to those glasses doped with TiO2, ZnO, and BaO. The thinner half-value layer was reported at 0.015 MeV, taking values 0.006, 0.005, 0.004, and 0.002 for samples with TiO2, ZnO, BaO, and PbO, respectively. SBT-Pb sample (with PbO) has a thinner HVL compared to other fabricated glass samples. The fabricated glasses’ thickness (Deq) equivalent to 1 cm of lead (Pb) was reported. The results demonstrated that Deq is high at low energy and equals 11.62, 8.81, 7.61, 4.56 cm for SBT-Ti, SBT-Zn, SBT-Ba, and SBT-Pb glass samples, respectively. According to the Deq results, the fabricated glasses have a shielding capacity between 30 and 43% compared to the pure Pb at gamma-ray energy of 1.5 MeV. At high energy (8 MeV), the transmission factor values for a thickness of 1 cm of the fabricated samples reach 88.68, 87.83, 85.95, and 83.11% for glasses SBT-Ti, SBT-Zn, SBT-Ba, and SBT-Pb, respectively.
Effect of B2O3 on the Radiation Shielding Performance of Telluride Lead Glass System

Shiyu Yin,Hao Wang,Shifeng Wang,Jing Zhang,Yuanzhi Zhu

DOI: https://doi.org/10.3390/cryst12020178

IF: 2.7

2022-01-26

Crystals

Abstract:This paper studies the role of B2O3 in the radiation shielding properties of (100-x)(60TeO2-40PbO)-xB2O3 glass systems where x = 0, 1, 2, 3, 4 and 5 mol%. Through the scanning electron microscope (SEM) and X-ray diffraction (XRD) tests of the glass, the structure of the glass was studied. Physical radiation sources (57Co, 60Co, 137Cs, 133Ba, and 241Am) and WinXCOM software were used to experimentally and theoretically calculate the radiation properties of the glass, respectively. The gamma shielding ability of the glass was evaluated using its mass decay coefficient (μm), half-value layer (HVL), mean free path (MFP) and effective atomic number (Zeff). The neutron shielding ability of the glass was evaluated by calculating the fast neutron removal cross-section (RCS) value. The glass’s gamma and neutron shielding properties were compared to various ordinary concrete and other tellurite glasses. The measured mass decay coefficients agree well with the theoretical values obtained using WinXCOM software. Low HVL, MFP, and high μm, Zeff, and RCS values indicate that this series of glass materials have good shielding properties. According to the obtained results, among the glass samples doped with B2O3, the TPB-1 glass sample showed the best radiation shielding performance.

materials science, multidisciplinary,crystallography
Nuclear radiation shielding performance of the new lead‐free TeO2–Bi2O3–ZnO–BaF2 glass

Shiyu Yin,Zhizhi Zhang,Yu Xiang,Qianqian Qiao,Guanzhou Ding,Xianchao Huang,Qiuhan Lin

DOI: https://doi.org/10.1111/ijac.14723

2024-02-28

International Journal of Applied Ceramic Technology

Abstract:This paper studied the radiation shielding properties of new lead‐free telluride glass with different BaF2 content. The 65TeO2–15Bi2O3–(20 − x)ZnO–xBaF2 glass systems (where x = 1, 3, 5, 7, 9 mol%) were tested through the X‐ray diffraction, ultraviolet–visible spectrophotometer, and differential scanning calorimetry. The glass system exhibited good thermal stability and a uniform surface without surface crystallization. The linear attenuation coefficient of the TBZBF series glass was tested using five different gamma radiation sources (241Am, 133Ba, 57Co, 137Cs, and 60Co). They were calculated to the mass attenuation coefficient, half‐value layer, mean free path, and effective atomic number through numerical simulations with XCOM software. The maximum mass attenuation coefficient for TBZBF‐9 was calculated to be 5.3577 cm2/g. Comparisons were made between this glass system and other tellurite and leaded glasses reported in the literature. The glass system exhibited superior radiation shielding capability compared to leaded tellurite glass under the same testing conditions. The gamma radiation shielding capacity increased with BaF2 content in the glass system. These results show that TBZBF‐9 exhibited the best gamma radiation shielding effectiveness while maintaining glass transparency.

materials science, ceramics
Effects of TeO2 and B2O3 on photon, neutron, and charged particle transmission properties of Bi2O3-BaO-LiF glass system

I. O. Olarinoye,Sultan Alomairy,Chahkrit Sriwunkum,H. H. Hegazy,M. S. Al-Buriahi

DOI: https://doi.org/10.1007/s41779-021-00616-y

2021-06-02

Journal of the Australian Ceramic Society

Abstract:This work investigates the effects of TeO2 and B2O3 on photon, neutron, and charged particle transmission properties of Bi2O3-BaO-LiF glass system. Photon transmission parameters were obtained via narrow beam setup simulation via FLUKA and those obtained from experimentally proved XCOM calculations. The attenuation factors of ( {left( aisebox{1ex}{$mu $}!left/ ! aisebox{-1ex}{$ ho $} ight. ight)}_{IS} )and ( {left( aisebox{1ex}{$mu $}!left/ ! aisebox{-1ex}{$ ho $} ight. ight)}_{PP} ) control the value of ( aisebox{1ex}{$mu $}!left/ ! aisebox{-1ex}{$ ho $} ight. ) at energies greater than 1.5 MeV; however, the region of influence differs for both absorption processes. While ( {left( aisebox{1ex}{$mu $}!left/ ! aisebox{-1ex}{$ ho $} ight. ight)}_{IS} ) peaks occur at 3 MeV, the influence of ( {left( aisebox{1ex}{$mu $}!left/ ! aisebox{-1ex}{$ ho $} ight. ight)}_{PP} )becomes appreciable at E > 5 MeV. The values of linear attenuation factor (μ) ranged from 0.2119–0.5283, 0.2085–0.5248, 0.1837–0.4676, 0.1639–0.4223, 0.1519–0.3971, 0.1370–0.3638, and 0.1222–0.3315 cm-1 as B2O3 increased from 0 to 60 mol % with step of 10, respectively. The spectra of projected range (R) of the ions and CSDA range of electrons show that the TSP of electrons in the glasses increases as B2O3 increased from 0 to 60 mol % for energy lower than 5 MeV; however, it reverses at 10 MeV. The ability of the present glass system for stopping the transmission of various radiation beams reveals its potential use for shielding applications in medical and nuclear facilities.

materials science, ceramics
Photon and neutron absorbing capacity of titanate-reinforced borate glasses: B2O3–Li2O–Al2O3–TiO2

Y. S. Rammah,I. O. Olarinoye,F. I. El-Agawany,Iskender Akkurt,E. Yousef

DOI: https://doi.org/10.1007/s10854-021-05447-y

2021-02-18

Abstract:The photon and neutron absorbing capacity of titanate-doped borate glasses: 65B2O3–30Li2O–5Al2O3–xTiO2: x = 0–30 mol% coded as G1–G7 were investigated via WinXCOM and EXABCal computer codes. Mass (µm) and linear (LAC) attenuation coefficients, mean-free path (MFP), half-value thickness (HVT), buildup factors (EABUF and EBUF), and the relative fast neutron absorbing efficacy were investigated. The maximum value of µm at 15 keV was 1.68, 2.976, 4.119, 5.134, 6.042, 6.856, and 7.593 cm2/g for G1, G2, G3, G4, G5, G6, and G7, respectively. For energies below 0.1 MeV and above 10 meV, µm values vary according to the order (G1)µm < (G2)µm < (G3)µm < (G4)µm < (G5)µm < (G6)µm < (G7)µm. Values of LAC followed the order: (G7)LAC > (G6)LAC > (G5)LAC > (G4)LAC > (G3)LAC > (G2)LAC > (G1)LAC. The trend of the MFP increases among the glasses follows a reverse order as that of LAC: (G1)MFP > (G2)MFP > (G3)MFP > (G4)MFP > (G5)MFP > (G6)MFP > (G7)MFP. The HVT of the glasses follow the order: (G1)HVT > (G2)HVT > (G3)HVT > (G4)HVT > (G5)HVT > (G6)HVT > (G7)HVT. EABUF and EBUF increase in the order (G1)(EABUF, EBUF) > (G2)(EABUF, EBUF) > (G3)(EABUF, EBUF) > (G4)(EABUF, EBUF) > (G5)(EABUF, EBUF) > (G6)(EABUF, EBUF) > (G7)(EABUF, EBUF). The investigated glasses (G1–G7) are better fast neutron absorbers compared to ordinary concrete and water. Results revealed that higher titanate doping concentrations produced better photon and fast neutron shielding capacities. Therefore, the investigated glasses showed superior shielding efficacy when compared with some traditional shielding materials; consequently, the G1–G7 glasses are recommended for use as ionizing radiation shields.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
Optical, structural, physical, and nuclear shielding properties, and albedo parameters of TeO2–BaO–B2O3–PbO–V2O5 glasses

Melek Fidan,Abuzer Acikgoz,Gokhan Demircan,Demet Yilmaz,Bulent Aktas

DOI: https://doi.org/10.1016/j.jpcs.2021.110543

IF: 4.383

2022-04-01

Journal of Physics and Chemistry of Solids

Abstract:In this study, glass systems were constructed according to the formula 34TeO2∙xBaO∙35B2O3∙(30-x)PbO∙1V2O5 (x=0, 5, 10, 15, 20, 30 mol%). The gamma, neutron, proton, and alpha shielding characteristics of the glasses were evaluated for nuclear security applications. The mass attenuation coefficient (MAC), half-value layer, mean free path, effective atomic number, and radiation protection efficiency (RPE) were experimentally measured in the energy range of 59.54–661.62 keV. In addition, the theoretical MAC values were determined. The exposure buildup factor, fast neutron removal cross section, mass stopping power, and projected range values for proton (H1) and alpha (He+2) particles were theoretically determined. Albedo parameters were measured for the prepared glasses at photon energy of 59.54 keV. The optical and structural properties were studied using X-ray diffraction, FT-IR Fourier transform infrared, ultraviolet–visible, and electron paramagnetic resonance spectroscopy. The glass samples comprised structural units such as TeO4, TeO3, BO3, and BO4. The spin Hamiltonian parameters, g ∥ , g ⊥ , A ∥ , A ⊥ , dipolar hyperfine coupling parameter, P, and Fermi contact parameter, κ , were calculated. The molecular orbital parameters, α 2 , β 2 , and γ 2 , were determined by optical absorption spectroscopy. The number of bonds per unit volume in the glasses ranged between 8.763 and 9.212×1028 m−3. The most reflective compound among the glasses investigated was BaO. Good agreement was found between the theoretical and experimental MAC values. TeBaBPbV1 glass was identified as a potential candidate for use in neutron, gamma, proton, and alpha shielding.

physics, condensed matter,chemistry, multidisciplinary
Photon Shielding Characterization of a Modified Titania-Bismuth-Borotellurite Glass System for Medical Applications

Hossam Donya,Salem Sulami

DOI: https://doi.org/10.3938/jkps.75.871

2019-12-01

Journal of the Korean Physical Society

Abstract:Shielding against ionizing radiation is considered a crucial issue for the radiation safety of patients and workers at radiology centers. For this purpose, the shielding effectiveness of a modified titania-bismuth-borotellurite (TiO2-Bi2O3-B2O3-TeO2) glass system at diagnostic energy ranges was investigated. This glass system is characterized by the high density of its components and its non-toxicity, which have given it an outstanding reputation in radiation shielding. A comparison of shielding characteristics between different compositions of the mentioned glass system and shielding materials frequently used at radiology centers, including lead glass and ordinary concrete, is implemented. The computational program WinXCom was utilized to evaluate the mass attenuation coefficients (µ/ρ)m of the glass compositions, lead glass and ordinary concrete. The incident diagnostic X-ray photon beams used in imaging tools such as computed tomography (CT), dental imaging, general radiography and mammography were employed at average energies of 60, 40, 30, and 20 keV, respectively. Additional shielding parameters, such as half-value layers (HVLs) and effective atomic numbers (Zeff), were also computed. The results revealed that among the materials tested, the glass system with high bismuth-oxide content in (i.e., the 30Te sample) is the best shielding material for different diagnostic imaging tools. Such a transparent glass system could be advantageous, as it is considered a green and environmentally friendly shielding material that can replace undesirable toxic lead glass and ordinary concrete, which occupies a large amount of space at radiology centers.

physics, multidisciplinary
Distance Education Strategy: Mental Models and Strategic Choices

J. C. Adams,Alan T. Seagren

2004-06-15

Abstract:What issues do distance education (DE) leaders believe will influence the future of DE? What are their colleges’ DE strategies? This qualitative study compares DE strategic thinking and strategic choices at three community colleges. Two propositions are investigated: (1) each college’s DE leaders use common strategic mental models (ways of thinking about key environmental issues and relationships), and (2) DE leaders from the three colleges employ common industry-level strategic mental models. The major findings are: (1) strategic beliefs are more varied than expected; (2) strategic choices address common DE issues but are tailored to local contexts; and (3) leaders’ beliefs and college strategic choices are aligned. Introduction The continuing rapid growth of post-secondary distance education (DE) poses major strategic challenges for all types of higher education institutions (Eaton, 2002). These challenges include: political and public pressure for new accreditation and quality standards (Eaton, 2001), faculty concerns about teaching loads and compensation, institutional concerns about costs and sustainability (Carr, 2001), and a variety of related institutional and public policy issues (American Council on Education, 2000). Strategy research is often conducted from two perspectives: strategy content and strategy process (Chakravarthy & White, 2002). Strategy content research investigates the objectives that organizations establish and the means they adopt to reach those objectives. Strategy process research examines the formulation, implementation, and alteration of strategy. One approach to strategy process focuses on the strategic mental models that decision makers employ to represent and manage complex external and internal environments (Porac & Thomas, 2002; Schwenk, 1988). This qualitative study investigated two propositions regarding DE strategic thinking at three Midwestern community colleges (identified as Elm, Maple, and Oak): (1) each college’s DE leaders used common strategic mental models (ways of thinking about key environmental issues and relationships), and (2) DE leaders from the three colleges employed common industry-level strategic mental models. This research also compared the colleges’ DE strategies. The research questions were:
Synergistic Effects of Bismuth Oxide on the Radiation Attenuation Characteristics of Borosilicate Glasses

Maryam Al Huwayz,Aljawhara Almuqrin,F.F. Alharbi,M.I. I Sayyed,B Albarzan

DOI: https://doi.org/10.1149/2162-8777/ad8e84

IF: 2.2

2024-11-06

ECS Journal of Solid State Science and Technology

Abstract:This work explores Bi2O3-doped borosilicate glasses' synthesis and radiation shielding characterization, and their applicability as radiation shields. The glasses are prepared via melt quenching in the composition series of 60B2O3-(22-x) SiO2-10CaO-(8+x)Bi2O3 (where x=4,8,12 and 16 mol%). The produced glasses' radiation shielding properties, such as the mass attenuation coefficient (MAC), the transmission factor (TF), and the effective atomic number (Zeff), were examined, and the effect of Bi2O3 on the samples' radiation shielding performance was explored. The glass sample with 24 mol% Bi2O3 exhibited notable efficiency in shielding against gamma radiation. This is evidenced by the favourable change in the MAC, TF, and Zeff with increasing Bi2O3 content. We examined the relation between the glass thickness and the TF, with the results revealing that the 0.6 cm thickness glass possesses the highest TF compared to a thickness of 1.2 cm, indicating that at the thickness of 1.2 cm, the glass material attenuates better compared to 0.6 cm. The relation between the glasses' density and their half value layer was also examined.

materials science, multidisciplinary,physics, applied
Fabrication, structure, optical and gamma-ray attenuation properties of borotellurite glasses doped with variable concentrations of cadmium oxide

Maryam Al Huwayz,A. M. Abdelghany,R. A. Elsad,Shaaban M. Shaaban,Y. S. Rammah,S. M. Kotb,S. Talaat,A. S. Abouhaswa

DOI: https://doi.org/10.1007/s11082-024-07120-0

IF: 3

2024-11-26

Optical and Quantum Electronics

Abstract:Glass samples of CdO doped bario-fluoride borotellurite with nominal compositions of (45-x)B 2 O 3 + 30TeO 2 + 15BaF 2 + 10Li 2 O + xCdO and substitution ratios of x = 0.0 (Cd0.0), 0.5 (Cd0.5), 2.0 (Cd2.0), 4.0 (Cd4.0), and 7.0 (Cd7.0) mol% were synthesized using the well-known melt quenching process. The structure, physical, and optical characteristics of the prepared glasses have been investigated. The Phy-X/PSD software employed to evaluate the radiation attenuation competence of the prepared glasses. The XRD analysis confirmed that the Cd-0.0/Cd-7.0 samples were in amorphous nature. Density (ρ) varied from 3.8633 g/cm 3 for Cd-0.0 sample to 4.2894 g/cm 3 for Cd-7.0 sample. The molar volume (V m ) varied from 28.08 cm 3 /mol to 26.25 cm 3 /mol. The inclusion of CdO in the glasses network reduced the direct band gaps from 3.54 eV to 3.196 eV and the indirect band gaps from 3.23 eV to 2.85 eV, respectively. Urbach's energy changed from 0.23 eV to 0.318 eV and refractive index (n) ranged between 2.333 and 2.439. Mass-absorption coefficient (MAC) values ranged between 30.696 − 0.032 cm 2 /g, 30.825–0.032 cm 2 /g, 31.210–0.032 cm 2 /g, 31.714–0.033 cm 2 /g and 32.450–0.033 cm 2 /g, for Cd0.0, Cd0.5, Cd2.0, Cd4.0, and Cd7.0 glass samples, respectively. Sample coded as Cd7.0 possessed the minimum half value layer (HVL) which ranged from 0.005 cm to 4.887 cm at photon energy 0.015 and 15 MeV, respectively. The effective atomic number (Z eff ) and effective ion density (N eff ) possessed the same trend of MAC parameter. Results confirmed that the present glasses are superior as γ-ray shields compared to other commercial materials.

engineering, electrical & electronic,optics,quantum science & technology
Glucagon regulates its own synthesis by autocrine signaling

B. Leibiger,T. Moede,T. Muhandiramlage,Daniel Kaiser,P. Sánchez,I. Leibiger,P. Berggren

DOI: https://doi.org/10.1073/pnas.1212870110

2012-12-03

Abstract:Peptide hormones are powerful regulators of various biological processes. To guarantee continuous availability and function, peptide hormone secretion must be tightly coupled to its biosynthesis. A simple but efficient way to provide such regulation is through an autocrine feedback mechanism in which the secreted hormone is “sensed” by its respective receptor and initiates synthesis at the level of transcription and/or translation. Such a secretion–biosynthesis coupling has been demonstrated for insulin; however, because of insulin’s unique role as the sole blood glucose-decreasing peptide hormone, this coupling is considered an exception rather than a more generally used mechanism. Here we provide evidence of a secretion–biosynthesis coupling for glucagon, one of several peptide hormones that increase blood glucose levels. We show that glucagon, secreted by the pancreatic α cell, up-regulates the expression of its own gene by signaling through the glucagon receptor, PKC, and PKA, supporting the more general applicability of an autocrine feedback mechanism in regulation of peptide hormone synthesis.
Novel virtual biopsy of the kidney with near infrared, reflectance confocal microscopy: a pilot study in vivo and ex vivo.

V. Campo‐Ruiz,G. Lauwers,R. Anderson,E. Delgado‐Baeza,S. González

DOI: https://doi.org/10.1016/S0022-5347(05)00008-X

Abstract:
Exploring Gamma Radiation Shielding: the Role of BaO in Borosilicate Glasses

M. I. Sayyed,Aljawhara H. Almuqrin,Chaitali V. More,U. Rilwan,M. Rashad,Mohamed Elsafi

DOI: https://doi.org/10.1007/s12633-024-03045-1

IF: 3.4

2024-06-13

Silicon

Abstract:The gamma ray shielding characteristics of different borosilicate glasses are examined in this work. Four glasses with a composition of 60B 2 O 3 –5Na 2 O–5PbO–(30-x)SiO 2 –xBaO, (x = 5, 10, 15, and 20 mol%) were created using the conventional melt quenching technique followed by an annealing step. Linear attenuation coefficient, LAC, values have been determined using HPGe semi-conductor detector. These values were compared with calculated values estimated from Phy-X software and a good matching was observed. The samples were irradiated using the point sources viz., Am 241 (0.0595 MeV), Cs 137 (0.6617 MeV) and Co 60 (1.173 and 1.330 MeV). The LAC data were further utilized in computations of other radiological parameters that are half value layer (HVL) and Tenth value layer (TVL). Furthermore, radiation shielding efficiency (RSE) of the prepared glass materials has been evaluated. The sample 10S20B exhibits higher values of LAC than the others because it has the largest density and weight fraction of elements with higher atomic numbers. The significance of the atomic number and density parameters-higher atomic number and density imply greater probability of interaction, leading to better attenuation.

materials science, multidisciplinary,chemistry, physical
Enhanced optical and structural traits of irradiated lead borate glasses via Ce3+ and Dy3+ ions with studying Radiation shielding performance

O. I. Sallam,Y. S. Rammah,Islam M. Nabil,Ahmed M. A. El-Seidy

DOI: https://doi.org/10.1038/s41598-024-73892-w

IF: 4.6

2024-10-19

Scientific Reports

Abstract:Lead borate glass is the best radiation shielding glass when lead is in high concentration. However, it has low transparency after radiation exposure. Radiation decreases transparency due to chemical and physical changes in the glass matrix, such as creating or healing defects in the glass network. The addition of rare earth elements like cerium and dysprosium oxides to lead borate glasses can improve their transparency and durability as radiation shielding barriers. The newly manufactured glasses' optical absorption, structural, and radiation shielding properties were measured. The optical characteristics of the generated samples were examined to determine the effect of the cerium/dysprosium ratio on the structural alterations, specifically in the presence of bridging oxygen (BO) and non-bridging oxygen (NBO). Incorporating Ce 3+ results in peaks at 195 nm for borate units, 225 nm for Ce 3+ , and a broadened peak at 393 nm due to overlapping peaks for Ce 3+ and Ce 4+ in the UV region. By adding Dy, multiple peaks are observed at 825, 902, 1095, 1275, and 1684 nm, corresponding to the transition from 6 H 15/2 ground state to 6 F 5/2 , 6 F 7/2 , 6 F 9/2 , 6 F 11/2 , and 6 H 11/2 . The samples were also tested before and after exposure to gamma irradiation from a 60 Co source at a dose of 75 kGy to assess their stability against radiation. The energy gap value during irradiation shows decreased non-bridging oxygen. The energy gap difference before and after irradiation for the M4 sample shows higher NBO to BO conversion, reducing radiation damage and improving structural stability. Furthermore, X-ray photoelectron spectroscopy was utilized to get insight into the coordination chemistry of the created glass samples. The half-value layer (HVL), radiation protection efficiency (RPE), neutron removal cross-section (FRNCS), mean free path (MFP), mass attenuation coefficients (MAC), and effective atomic numbers (Z ef ) of the glassy structure were calculated theoretically to assess its radiation shielding qualities. The linear attenuation coefficient order for the prepared samples was M1 > M2 > M3 > M4. The FRNCS values were 0.090, 0.083, 0.081, and 0.079 cm −1 for samples M1, M2, M3, and M4, respectively.

multidisciplinary sciences

An integrative approach to quality assurance.

Enhancing radiation shielding effectiveness: a comparative study of barium-doped tellurite glasses for gamma and neutron radiation protection

Highly transparent glass of barium-reinforced borotellurite as a protective material from gamma rays

Designing High-Density of PbO-Enriched Telluro-Borate Glasses for Improved Radiation Shielding: A Comprehensive Study of Attenuation Parameters

Optical properties and radiation shielding competence of Bi/Te-BGe glass system containing B2O3 and GeO2

Radiation shielding performance of tellurium–thallium and tellurium–lead oxide glass systems

New transparent rare earth glasses for radiation protection applications

Impact of Modifier Oxides on Mechanical and Radiation Shielding Properties of B2O3-SrO-TeO2-RO Glasses (Where RO = TiO2, ZnO, BaO, and PbO)

Effect of B2O3 on the Radiation Shielding Performance of Telluride Lead Glass System

Nuclear radiation shielding performance of the new lead‐free TeO2–Bi2O3–ZnO–BaF2 glass

Effects of TeO2 and B2O3 on photon, neutron, and charged particle transmission properties of Bi2O3-BaO-LiF glass system

Photon and neutron absorbing capacity of titanate-reinforced borate glasses: B2O3–Li2O–Al2O3–TiO2

Optical, structural, physical, and nuclear shielding properties, and albedo parameters of TeO2–BaO–B2O3–PbO–V2O5 glasses

Photon Shielding Characterization of a Modified Titania-Bismuth-Borotellurite Glass System for Medical Applications

Distance Education Strategy: Mental Models and Strategic Choices

Synergistic Effects of Bismuth Oxide on the Radiation Attenuation Characteristics of Borosilicate Glasses

Fabrication, structure, optical and gamma-ray attenuation properties of borotellurite glasses doped with variable concentrations of cadmium oxide

Glucagon regulates its own synthesis by autocrine signaling

Novel virtual biopsy of the kidney with near infrared, reflectance confocal microscopy: a pilot study in vivo and ex vivo.

Exploring Gamma Radiation Shielding: the Role of BaO in Borosilicate Glasses

Enhanced optical and structural traits of irradiated lead borate glasses via Ce3+ and Dy3+ ions with studying Radiation shielding performance