Radiological cases of the month. Osteogenic sarcoma as a second malignant neoplasm in a child with retinoblastoma.

P. M. Loo,B. Wood

A M A Journal of Diseases of Children

Abstract:

What problem does this paper attempt to address?

Low Cycle Fatigue Properties and Fracture Mechanism of Q345qC Steel and Its Welded Joint

LIAO Yan-hua,XIE Xu,TANG Zhan-zhan

DOI: https://doi.org/10.3785/j.issn.1008-973x.2018.01.011

2017-01-01

Abstract:Low cycle fatigue tests were conducted for base metal and weld metal specimens under the total strain range from 2.0％ to 5.0％ in order to analyze the low cycle fatigue properties of Q345qC steel and its welded joint.The low cycle fatigue life prediction curves were fitted based on the Coffin-Manson formula.The accuracy of different fatigue life prediction models were compared combining with the monotonic tensile tests.The crack initiation mechanism of welded joint and the effect of welding defect on fatigue life were analyzed by electron microscope scanning.The low cycle fatigue damage index formulas were derived based on the Miner damage accumulation theory.Results show that the fatigue life of welded joint is only 31％～ 50％ of that of base metal under the same strain level.The cyclic response characteristic of base metal is cyclic stability,while that of welded joint shows cyclic softening.The energy dissipation capacity is similar between base metal and welded joint on half-life stable circulation state.The Coffin-Manson formula has a relatively higher accuracy on both low cycle fatigue and extremely low cycle fatigue life prediction considering the monotonic tensile tests.Welding defect can easily cause fatigue crack initiation,leading to a significant decrease on fatigue life.
Fatigue Testing in Welded Joint of 980- grade Steels

冷建兴,尹强,丁荣华,徐秉汉

DOI: https://doi.org/10.3969/j.issn.1007-7294.2003.02.010

2003-01-01

Abstract:The fatigue strength is closely related to the material, the structural arrangement, the manufacture technology as well as the levels of the stress and strain. And the testing-frequency is closely related to the fatigue life too when the alternate stress is higher than yield stress. In the fatigue tests this paper used the stress-control when the real stress is lower than the yielding stress, and used the strain-control when the calculated strain higher than the yield strain. On this basis, several fatigue test models were designed. Fatigue strength tests for the butt-welded joint and the T-typed welded joint were carried out. The test results show that it is useful for the design of the structure of the 980-grade steel.
Research on the P‐S‐N Curve Fitting Method of Notched Specimens Considering Small Sample Properties

Ziyang Zhang,Jianhui Liu,Juntai Hu,Qingjun Wu,Shenglei Wu

DOI: https://doi.org/10.1111/ffe.14490

IF: 3.373

2024-11-01

Fatigue & Fracture of Engineering Materials & Structures

Abstract:Aiming at the issue of fatigue test data for large‐scale mechanical components of building steel are very limited, a method for fitting P‐S‐N curves under small sample data of notched specimens is proposed to predict fatigue life. First, a fatigue life subsample augmented and its reliability assessment method are established, based on Bayesian hierarchical modeling and modified Monte Carlo method. Second, a clustering combination weighting method is proposed, to define weights of hidden variables of the binomial mixture Weibull distribution, and the expectation–maximization algorithm is used to determine probability density function of the distribution. Finally, the P‐S‐N curves under various failure probabilities are fitted with Weibull distributed life models, and the convergence and prediction accuracy of the different models are compared. The results show that the fatigue data of small samples can be predicted better by using mixed Weibull distribution, and the fitting P‐S‐N curve is more reliable and accurate.

materials science, multidisciplinary,engineering, mechanical
ESS-based Probabilistic Fatigue Life Assessment of Steel Bridges: Methodology, Numerical Simulation and Application

Y. H. Su,X. W. Ye,Y. Ding

DOI: https://doi.org/10.1016/j.engstruct.2021.113802

IF: 5.582

2022-01-01

Engineering Structures

Abstract:The selection of an appropriate S-N curve for a specified type of welded joints is an essential part for the fatigue reliability assessment of steel bridges by means of a stress-life approach. However, this is still a challenging issue in the real engineering applications due to the complexity of the structural components and the lack of the available numbers and types of S-N curves. In this study, a generalized fatigue reliability model based on equivalent structural stress (ESS) is proposed, which has the merit of taking no account of the selection of the S-N curve. An ESS-based probabilistic S -N formulation is first derived by introducing a probability index to the expression of the S -N curve. Then, the fatigue reliability model, which incorporates the random variables of the ESS range, the number of cycles and material properties, is deduced by combining the Miner's rule. Numerical case studies and sensitivity analyses on the effects of the ESS range, the number of cycles and the growth in traffic volume are performed to evaluate the practicability and the effectiveness of the proposed fatigue reliability model. Finally, the proposed method is applied to an instrumented steel arch bridge with the aid of field dynamic strain data. The fatigue failure probability and the fatigue reliability index versus fatigue life are achieved through random samples generated by means of the Monte Carlo (MC) simulation on the basis of the joint probability density function (PDF) of random variables. The results show that the proposed method provides a viable way of resolving the difficulty in selecting a suitable category for the evaluation of the probabilistic fatigue life of the welded details in steel bridges. In addition, it can be found that both the PDF of stress spectrum and the growth of traffic volume are sensitive to the failure probability and reliability index obtained by the proposed fatigue reliability model.
Three-Parameter P-S-N Curve Fitting Based on Improved Maximum Likelihood Estimation Method

Xiufeng Tan,Qiang Li,Guanqin Wang,Kai Xie

DOI: https://doi.org/10.3390/pr11020634

IF: 3.5

2023-02-20

Processes

Abstract:The P-S-N curve is a vital tool for dealing with fatigue life analysis, and its fitting under the condition of small samples is always concerned. In the view that the three parameters of the P-S-N curve equation can better describe the relationship between stress and fatigue life in the middle- and long-life range, this paper proposes an improved maximum likelihood method (IMLM). The backward statistical inference method (BSIM) recently proposed has been proven to be a good solution to the two-parameter P-S-N curve fitting problem under the condition of small samples. Because of the addition of an unknown parameter, the problem exists in the search for the optimal solution to the three-parameter P-S-N curve fitting. Considering that the maximum likelihood estimation is a commonly used P-S-N curve fitting method, and the rationality of its search for the optimal solution is better than that of BSIM, a new method combining BSIM and the maximum likelihood estimation is proposed. In addition to the BSIM advantage of expanding the sample information, the IMLM also has the advantage of more reasonable optimal solution search criteria, which improves the disadvantage of BSIM in parameter search. Finally, through the simulation tests and the fatigue test, the P-S-N curve fitting was carried out by using the traditional group method (GM), BSIM, and IMLM, respectively. The results show that the IMLM has the highest fitting accuracy. A test arrangement method is proposed accordingly.

engineering, chemical
Fatigue Analysis of Typical Welded Joints of Steel Bridges Using Effective Notch Stress Approach

LIAO Xiao-wei,WANG Yuan-qing,ZONG Liang,SHI Gang

DOI: https://doi.org/10.3785/j.issn.1008-973x.2017.01.001

2017-01-01

Abstract:The fatigue life evaluation procedure based on the S-N curves was simplified in order to validate the applicability of the effective notch stress approach to the welded joints of steel bridge.Fatigue tests were performed for the unequal thickness butt-welded joints,non-load-carrying fillet-welded cruciform joints and load-carrying fillet-welded cruciform joints when the stress ratio is 0.1.Then the local effective notch stress at the weld toe or weld root was analyzed by numerical calculation with ABAQUS,and the SN curves in the effective notch stress system of the above-mentioned welded details were obtained.Effects of the values of effective notch stress on the fatigue failure modes of welded joints were investigated.The experimental and analytical results indicate that the size of the welding misalignment will determine the fatigue failure mode of the load-carrying fillet-welded cruciform joint,and the effective notch stress approach can distinguish the crack initiation location at weld toe or root.Nominal stress approach exhibits more conservative than the effective notch stress approach with FAT225 design curves.Experimental data demonstrates that FAT200 S-N curve will be more acceptable.
Research on fatigue curve fitting methods based on the notch stress approach

Shengfu Xue,Zhengping He,Bingzhi Chen,Jianxin Xu

DOI: https://doi.org/10.1108/ijsi-10-2023-0106

2024-01-07

International Journal of Structural Integrity

Abstract:Purpose This study investigates the fitting techniques for notch fatigue curves, seeking a more reliable method to predict the lifespan of welded structures. Design/methodology/approach Building on the fatigue test results of butt and cruciform joints, this research delves into the selection of fitting methods for the notch fatigue curve of welded joints. Both empirical formula and finite element methods (FEMs) were employed to assess the notch stress concentration factor at the toe and root of the two types of welded joints. Considering the mean stress correction and weld misalignment coefficients, the notch fatigue life curves were established using both direct and indirect methods. Findings An engineering example was employed to discern the differences between the direct and indirect approaches. The findings highlight the enhanced reliability of the indirect method for fitting the fatigue life curve. Originality/value While the notch stress approach is extensively adopted due to its accurate prediction of component fatigue life, most scholars have overlooked the importance of its curve fitting methods. Existing literature scantily addresses the establishment of these curves. This paper offers a focused examination of fatigue curve fitting techniques, delivering valuable perspectives on method selection.
A method for prediction of S-N curve of spot-welded joints based on numerical simulation

L. Yang,B. Yang,G.W. Yang,S.N. Xiao,T. Zhu,F. Wang

DOI: https://doi.org/10.14743/apem2022.2.426

2022-06-30

Advances in Production Engineering & Management

Abstract:Currently, ΔF-N curves are often used to predict the fatigue lives of spot-welded joints, but the method for obtaining these ΔF-N curves is time-consuming, laborious, and non-universal. Tensile-shear fatigue tests were performed to obtain the fatigue lives and the corresponding normalized S-N curves of spot-welded joints. Subsequently, the force acting at the spot-welded joints was obtained by extracting the force and moment of the beam element in the shell-element-based finite element model, and the equivalent structural stress at the spot-welded joint was obtained based on the equiva-lent structural stress method. Finally, the S-N curves of the spot-welded joints were fitted using the least-squares method. A comparison of the S-N curves of the spot-welded joints with those of different materials revealed that the material type had a significant influence on the S-N curve. To avoid this influence, a method for predicting the S-N curve of the spot-welded joints was proposed based on the relationship between the ratio of the ten-sile strength and that of the fatigue limit of each material. This research provides guidance for predicting the fatigue life of spot-welded joints in engineering applications.

engineering, manufacturing,materials science, multidisciplinary
Experimental and Numerical Characterization of Low Cycle Fatigue and Creep Fatigue Behaviour of P92 Steel Welded Joint

X. Wang,W. Zhang,J. Gong,Y. Jiang

DOI: https://doi.org/10.1111/ffe.12722

IF: 3.373

2017-01-01

Fatigue & Fracture of Engineering Materials & Structures

Abstract:Low cycle fatigue (LCF) and creep fatigue interaction (CFI) behaviour of P92 steel welded joint were investigated experimentally and numerically. Strain-controlled LCF tests at different strain amplitudes and CFI tests at different peak strain holding time were conducted. Evolutions of cyclic stress response, mean stress, and creep strain during cycling were described, in which the influence of strain amplitude and holding time were investigated. A specific heat treatment process was proposed to get the homogenous simulated material of fine grain region and coarse grain region in the heat affected zone. Material parameters of parent material, fine grain heat affected zone, coarse grain heat affected zone, and weld metal in the unified viscoplasticity model were then determined and validated. To predict the LCF and CFI behaviour of welded joint, 3-dimensional unified viscoplasticity model with a modified isotropic variable was compiled into ABAQUS UMAT. The comparison between the predicted and experimental result under LCF and CFI loadings showed that the simulation results were reasonable and agreed with the experimental data well.
PROBABILISTIC SPECIMEN PROPERTY-FATIGUE LIFE MAPPING AND P-S-N CURVE FITTING

Liyang Xie,Jianzhong Liu,Ningxiang Wu,Wenxue Qian

DOI: https://doi.org/10.1142/s0218539313500204

2013-01-01

Abstract:Fitting P-S-N curve with small-size sample of fatigue test data is significant in engineering applications. Although several small sample-based P-S-N curve fitting methods have been developed, complexity in mathematics and/or the unrealistic assumption of the methods hinder their application seriously. Based on the principle of probabilistically mapping from the probability distribution of specimen property to that of fatigue life of the specimen, this paper presents a new, easy to apply P-S-N curve fitting method. By collecting the life distribution information dispersed in several small-size samples of fatigue lives tested under different cyclic stress levels, a large-size sample of equivalent fatigue life data can be built based on the mapping mechanism as well as the uniqueness of the relationship between fatigue life standard deviation and cyclic stress level. The basic viewpoint is that the fatigue lives tested at any cyclic stress levels can be equivalently converted to an arbitrary baseline stress level according to the life distribution–stress relationship, and this principle can be applied to determine the P-S-N curves with a limited number of test data. Test results illustrate that the P-S-N curves obtained by such methods with 30, 24 or 20 samples, respectively, are close to those obtained by the conventional test method with 60 or 40 samples.
Investigation on Fatigue Behaviour of Load-Carrying Fillet Welded Joints Based on Mix-Mode Crack Propagation Analysis

Tsinghua University,Shi Gang,Wang Yuan-Qing,Ministry of Education

DOI: https://doi.org/10.1016/j.acme.2017.01.009

IF: 4.042

2017-01-01

Archives of Civil and Mechanical Engineering

Abstract:The fatigue behaviour of the load-carrying fillet welded joints was investigated by experimental and numerical approach in this paper. 26 load-carrying cruciform fillet welded joints involving 8 stress levels were tested and the S-N curves of 95% survival probability in terms of toe failure and root failure were established separately. The testresults also demonstrate that the design curves of Eurocode3 are not suitable for this batch of specimens. In the following numerical simulations, three types of initial crack assumption were analysed by 3D mix-mode fatigue crack propagation analysis according to experimental observation. All the possible crack growth routes were simulated well. However, the single crack assumptions cannot form satisfactory simulations on fatigue lives with enough safety stock. Therefore, multi-crack analysis was conducted based on the combined data in terms of both toe failure and root failure. It is found that multi-crack analysis with 0.5 mm weld toe initial line crack and 0.1 mm weld root initial line crack can provide appropriate prediction. The findings can be beneficial for the fatigue assessment of load-carrying fillet welded joints fabricated by the normal welding technique in China and offer somereferences for the fatigue assessment of structural details with different possible failure modes.
S-N curve modeling method of Aluminum alloy welded joints based on the fatigue characteristics domain

Li Zou,Xinhua Yang,Jianrong Tan,Yibo Sun

DOI: https://doi.org/10.3221/IGF-ESIS.40.12

2017-01-01

Frattura ed Integrita Strutturale

Abstract:The scatter degree of the fatigue samples is reduced when the nodal force based structural method is used for steel welded joints, while it is still high for aluminum alloy welded joints. Statistical method and rough set theory is used to fatigue analysis so that fatigue characteristic domains are determined and S-N curves are fitted. Experiment results show that fatigue life of the aluminum alloy welded joints is under the influence of some key factors and the fatigue data with the same characteristics distribute in a relatively independent area. Accordingly, a novel S-N curve modeling method of aluminum alloy welded joints based on the fatigue characteristics domain is proposed. In the proposed method, the nodal force based structural stress method is used for stress calculation and neighborhood rough set theory is used for character extraction to obtain the key factors. Then fatigue characteristics domains are divided and S-N curves are fitted on each fatigue characteristics domain instead of on the whole domain so that a set of S-N curves are obtained. Statistical results show that selection of the S-N curve for the aluminum alloy welded joints according to different fatigue characteristic domain is more accurate.
Determination of the fatigue P-S-N curves – A critical review and improved backward statistical inference method

Cunhai Li,Shengchuan Wu,Jinyuan Zhang,Liyang Xie,Yanhui Zhang

DOI: https://doi.org/10.1016/j.ijfatigue.2020.105789

IF: 5.489

2020-10-01

International Journal of Fatigue

Abstract:To increase the prediction accuracy of small-number sample life data, improved backward statistical inference approach (ISIA) was formulated using the modified distribution coefficients while fitting the fatigue probabilistic S-N (P-S-N) curve. Based on the search path searching for fatigue parameters, the novel scheme captures the optimal coefficients that can efficiently correlate the life distribution and stress levels. The equivalent lives can be obtained through the conversion of fatigue life to the highest stress level. To acquire a realistic P-S-N curve of full-scale components, the life distribution effect of small-number samples can be considered when fitting curves. Results show that for a set of data with an accurate standard deviation at the first stress level, the predicted lifetime using the ISIA is approximately 8.7% of the conventional group method and is only 10.5% of the original backwards statistical inference method. Meanwhile, by comparing the predicted results with the fatigue life testing data of full-scale alloy steel EA4T axles, the accuracy of fatigue P-S-N curves by using ISIA is further confirmed. For the modern axle materials and welded structures widely used in railway vehicles, the newly-proposed ISIA can not only achieve a reliable fatigue life, particularly in the high cycle fatigue regime, but also provide a more conservative fatigue P-S-N curve than traditional fitting methods.

materials science, multidisciplinary,engineering, mechanical
Experimental and Numerical Investigation on Fatigue Performance of Non-Load-carrying Fillet Welded Joints

Liang Zong,Gang Shi,Yuan-Qing Wang,Zhong-Xian Li,Yang Ding

DOI: https://doi.org/10.1016/j.jcsr.2016.12.010

IF: 4.349

2016-01-01

Journal of Constructional Steel Research

Abstract:Fatigue performance of non-load-carrying fillet welded details was investigated by experimental and numerical approaches in this paper. Fatigue tests were conducted on 26 non-load-carrying cruciform fillet welded joints. 23 effective fatigue test data were acquired and experimental S-N curve was established. The test results are representative on reflecting the fatigue performance of the non-load-carrying fillet welded details fabricated in China and provide essential data for developing related design codes. In comparison with the test data, the design S-N curve in Eurocode3 is proved to be suitable in generally but does not have sufficient safety stock for this batch of specimens. Afterwards, 3D mix-mode fatigue crack growth simulation was developed based on four initial crack assumptions. Comparisons between the predicted fatigue lives and experimental fatigue lives were carried out. It is found that the line cold lap assumption with 0.1mm initial value can give the best prediction on the average experimental fatigue lives. Nevertheless, I-type line crack assumption with 0.01mm initial value can provide suitable prediction in line with the experimental S-N curves of 95% survival probability and therefore it is recommended to be taken for fatigue crack propagation analysis when no specific inspection information is available. The influence of misalignment on fatigue lives are also analyzed, which could provide useful reference for practical engineering projects.
A Fatigue Life Prediction Approach for Resistance Spot Welded Joints with Consideration of the Stress Ratio Effect

Hu Liu,Xin-Hao Huo,Ze-Hao Zhang,Wang-Kai Yan,Dao-De Zhang

DOI: https://doi.org/10.1007/s11665-024-09168-1

IF: 2.3

2024-01-25

Journal of Materials Engineering and Performance

Abstract:Fatigue lives of ST12 lap-shear resistance spot welded joints have been tested under the stress ratios of R = 0.4, 0.2 and 0.06. The experimental results reveal that fatigue lives are significantly affected by stress ratios. Subsequently, the growth rate curves for fatigue cracks on ST12 low carbon steel plates under the stress ratios of R = − 1.0, − 0.3, 0.2 are tested, respectively, and the d a /d N − Δ K eff curve of the material is derived by using the Newman's opening stress equation. Finally, with the findings of the study, a new approach for predicting fatigue lives of spot welded joints which can take the stress ratio effect into consideration is proposed. The accuracy of the approach has been verified using experimental data, which demonstrates good agreement of the fatigue lives from the predictions and the experimental measurements. These findings have important implications for understanding the spot welded joints with respect to their fatigue behaviors under cyclic loadings, particularly in scenarios where fatigue lives may be significantly impacted by stress ratios.

materials science, multidisciplinary
Probabilistic fatigue evaluation of notched specimens considering small sample properties under multiaxial loading

Yingbao He,Jianhui Liu,Jumei Lu,Jie Wang,Ruicheng Feng,Junqiang Ren

DOI: https://doi.org/10.1016/j.tafmec.2024.104316

IF: 4.374

2024-02-10

Theoretical and Applied Fracture Mechanics

Abstract:Probabilistic fatigue evaluation is the key to ensure the service integrity of large-sized mechanical equipment, but in practical engineering, the probabilistic fatigue models coupled with multiaxial stress conditions and small sample information characteristics are still insufficient. Accordingly, the virtual subsample augmentation method is effectively coupled with the improved Bootstrap method to propose a general probabilistic fatigue evaluation process. Specifically, the random sample regeneration method is first used to expand the small sample fatigue data, and then life distribution information under different stress levels is fused based on the backwards statistical inference method, the P-S-N curve is fitted with the integrated life dispersion information. Secondly, a new fatigue damage parameter based on the inhibition function is proposed to modify the P-S-N curve and predict fatigue life. Meantime, the multiaxial fatigue test of Q355(D) alloy steel with different notch sizes is carried out, and the model is verified in conjunction with existing fatigue test data of TC4-DT alloy and TC4 alloy. The results show that the proposed model has a certain universality for notched specimens, the modified stress field intensity method can accurately characterize the impact of notch and size effects on fatigue damage of specimens.

engineering, mechanical,mechanics
An Approach to Estimate the Low Cycle Fatigue Probabilistic Curves of PBF-LB/M 316L Steel from Small Size Datasets Using the Remora Optimization Algorithm

Yefeng Chen,Xiaowei Wang,Zhen Zhang,Dewen Zhou,Yong Jiang,Jian Weng,Frank Walther,Jianming Gong

DOI: https://doi.org/10.1016/j.ijfatigue.2024.108375

IF: 5.489

2024-01-01

International Journal of Fatigue

Abstract:The significant dispersion in fatigue properties is a prevalent attribute observed in metals manufactured by the Additive Manufacturing (AM). To ascertain the safety of components subjected to low cycle fatigue (LCF) loadings at a temperature of 550 degrees C, it is necessary to carry out a fatigue reliability assessment of AM metals. Nevertheless, the number of LCF life tests is limited owing to time-consuming nature of test and high total production cost of AM materials. Such a small size dataset cannot satisfy the criteria of the traditional reliability assessment method. This work aims to develop a novel method to evaluate the LCF reliability of 316L stainless steel manufactured by laser-based powder bed fusion of metals (PBF-LB/M) technology. Firstly, the Weibull model is coupled with the Coffin-Manson-Basquin relationship in order to characterize the dispersion of life data points at various strain levels. Secondly, reliability results from a small size dataset show a maximum relative error in fatigue life of less than 25 %, which is similar to results from a large size dataset and the traditional method using fatigue data from public sources. Among this step, the remora optimization algorithm is firstly applied to calculate the characteristic parameters of newly-proposed method. Thirdly, the LCF reliability of PBFLB/M 316L based on the small size dataset is evaluated. The N95% is equivalent to 44 % of N50%. Finally, the PBFLB/M 316L is compared with traditional 316L considering the reliability. The LCF properties of PBF-LB/M 316L is similar to the traditional 316L at 50 % reliability, however it's slightly worse at 95 % reliability.
Principle of Sample Polymerization and Method of P-S-N Curve Fitting

XIE Liyang,LIU Jianzhong

DOI: https://doi.org/10.3901/jme.2013.15.096

2013-01-01

Journal of Mechanical Engineering

Abstract:˖In sense of probability percentiles, there exists a correspondence between specimen fatigues lives associated with different cyclic stress levels.Based on such a correspondence, the principle to fit P-S-N curve with small sample test data is investigated, which related with information fusion techniques, and the method to establish P-S-N equation.By polymerizing fatigue life test data under different cyclic stress levels and integrating the life distribution information, small sample experiment data can be efficiently applied to acquire the necessary information to estimate the parameters of the probability distributions of fatigue lives associated with any stress levels.According to the relationship between life distribution and cyclic stress level, fatigue life test data at different stress levels can be equivalently converted to an arbitrarily specified baseline stress level, and the distribution of the equivalent lives is identical with that of the test data at the baseline stress level if the relationship is correct.With the mean life -stress level relationship fitted by small sample test data, the correct relationship between life standard deviation and stress level can be found by statistical test oriented perturbation technique.Test results illustrate that the P-S-N curves fitted by this method with 20-30 specimens are very close to those obtained by fitted by conventional method with 40-60 specimens.Key words˖P-S-N curve Small size sample Sample congregation Information fusion Equivalent life 0
Fatigue reliability assessment of welded joints in steel bridges considering multiple effects

叶肖伟,傅大宝,倪一清,黄启远,姜绍飞

2013-01-01

Abstract:A novel method for fatigue reliability assessment of welded joints in steel bridges is proposed by considering multiple effects in terms of the stress concentration phenomenon at the welded joint as well as the reduction of the effective cross-sectional area and the degradation of the fatigue behavior due to steel corrosion.The proposed method is applied to assess the fatigue reliability of a typical welded joint in the instrumented Tsing Ma Bridge using the long-term strain monitoring data.By exploring the stochastic characteristics of the hot spot stress range,the reduction model of the cross-sectional area,and the fatigue behavior degradation function of the welded joint,a fatigue reliability model considering multiple effects is developed in the framework of a continuous probabilistic formulation of Miner's damage cumulative rule.A standard daily stress spectrum accounting for highway traffic,railway traffic,and typhoon effects is derived by statistically analyzing the long-term strain monitoring data.A multi-modal Probability Density Function(PDF) of the standard daily stress spectrum is obtained by use of the method of finite mixture distributions in conjunction with a Genetic Algorithm-based(GA-based) mixture parameter estimation approach.A comparative study is conducted to investigate the effects of stress concentration and steel corrosion(i.e.,reduction of the effective cross-sectional area and degradation of the fatigue behavior) on the failure probability and reliability index versus the predicted fatigue life of the welded joint.The results show that the fatigue reliability of the welded joint is significantly influenced by the effects of stress concentration and steel corrosion.
Experimental study of fatigue behaviour of Q690qENH bridge weathering high-strength steel welded joints

Shuling Gao,Ning Li,Yiming Huang,Jiabao Yan,Lijun Yang

DOI: https://doi.org/10.1016/j.tws.2023.110954

IF: 5.881

2023-07-03

Thin-Walled Structures

Abstract:The Q690qENH weathering high-strength steel has a considerable potential for bridge engineering due to its superior mechanical strength, toughness, and corrosion resistance . To evaluate its performance under fatigue loads, the high-cycle fatigue behaviour of Q690qENH base metal and its welded joints is studied. A total of 68 specimens are tested to obtain their stress–fatigue life ( S−N ) curves. Results show that the fatigue strengths of the base metal, butt-welded joint, and cross-welded joint are greater than those specified in the ANSI/AISC 360-16, Eurocode 3-2005, and BS 7608-2014 design standards. The most suitable S−N curve for evaluating the fatigue properties of the Q690qENH base metal, butt-welded joint, and cross-welded joint was deemed to be that given by ANSI/AISC 360-16. New S−N curves were proposed for the base metal and butt-welded joint, whereas the S−N curve for the cross-welded joint remained unchanged as per the existing codes. Additionally, the cumulative fatigue damage behaviour of the butt-welded and cross-welded joints was analysed, and a safety threshold based on the ratcheting strain rate was established to provide early warning at 85%–95% of fatigue life. Through digital image correlation and fatigue fracture analysis, the cause of fatigue fracture in the welded joints was determined to be caused by stress concentration at the weld toe.

engineering, mechanical,mechanics, civil

Radiological cases of the month. Osteogenic sarcoma as a second malignant neoplasm in a child with retinoblastoma.

Low Cycle Fatigue Properties and Fracture Mechanism of Q345qC Steel and Its Welded Joint

Fatigue Testing in Welded Joint of 980- grade Steels

Research on the P‐S‐N Curve Fitting Method of Notched Specimens Considering Small Sample Properties

ESS-based Probabilistic Fatigue Life Assessment of Steel Bridges: Methodology, Numerical Simulation and Application

Three-Parameter P-S-N Curve Fitting Based on Improved Maximum Likelihood Estimation Method

Fatigue Analysis of Typical Welded Joints of Steel Bridges Using Effective Notch Stress Approach

Research on fatigue curve fitting methods based on the notch stress approach

A method for prediction of S-N curve of spot-welded joints based on numerical simulation

Experimental and Numerical Characterization of Low Cycle Fatigue and Creep Fatigue Behaviour of P92 Steel Welded Joint

PROBABILISTIC SPECIMEN PROPERTY-FATIGUE LIFE MAPPING AND P-S-N CURVE FITTING

Investigation on Fatigue Behaviour of Load-Carrying Fillet Welded Joints Based on Mix-Mode Crack Propagation Analysis

S-N curve modeling method of Aluminum alloy welded joints based on the fatigue characteristics domain

Determination of the fatigue P-S-N curves – A critical review and improved backward statistical inference method

Experimental and Numerical Investigation on Fatigue Performance of Non-Load-carrying Fillet Welded Joints

A Fatigue Life Prediction Approach for Resistance Spot Welded Joints with Consideration of the Stress Ratio Effect

Probabilistic fatigue evaluation of notched specimens considering small sample properties under multiaxial loading

An Approach to Estimate the Low Cycle Fatigue Probabilistic Curves of PBF-LB/M 316L Steel from Small Size Datasets Using the Remora Optimization Algorithm

Principle of Sample Polymerization and Method of P-S-N Curve Fitting

Fatigue reliability assessment of welded joints in steel bridges considering multiple effects

Experimental study of fatigue behaviour of Q690qENH bridge weathering high-strength steel welded joints