Abstract:The Haber–Bosch (HB) process is the primary chemical synthesis technique for industrial production of ammonia (NH3) for manufacturing nitrate-based fertilizer and as a potential hydrogen carrier. The HB process alone is responsible for over 2% of all global energy usage to produce more than 160 million tons of NH3 annually. Iron catalysts are utilized to accelerate the reaction, but high temperatures and pressures of atmospheric nitrogen gas (N2) and hydrogen gas (H2) are required. A great deal of research has aimed at increased performance over the last century, but the rate of progress has been slow. This Account focuses on determining the atomic-level reaction mechanism for HB synthesis of NH3 on the Fe catalysts used in industry and how to use this knowledge to suggest greatly improved catalysts via a novel paradigm of catalyst rational design.We determined the full reaction mechanism on the two most active surfaces for the HB process, Fe(111) and Fe(211)R. We used density functional theory (DFT) to predict the free-energy barriers for all 12 important reactions and the 34 most important 2 × 2 surface configurations. Then we incorporated the mechanism into kinetic Monte Carlo (kMC) simulations run for several hours of real time to predict turnover frequencies (TOFs). The predicted TOFs are within experimental error, indicating that the predicted barriers are within 0.04 eV of experiment.With this level of accuracy, we are poised to use DFT to improve the catalyst. Rather than forming bulk alloys with uniform concentration, we aimed at finding additives that strongly prefer near-surface sites so that minor amounts of the additive might lead to dramatic improvements. However, even for a single additive, the combinations of surface species and reactions multiplies significantly, with ∼48 reaction steps to examine and nearly 100 surface configurations per 2 × 2 site. To make it practical to examine tens of dopant candidates, we developed the hierarchical high-throughput catalysis screening (HHTCS) approach, which we applied to both the Fe(111) and Fe(211) surfaces. For HHTCS, we identified the most important 4 reaction steps out of 12 for the two surfaces to examine >50 dopant cases, where we required performance at each step no worse than for pure Fe. With HHTCS, the computational cost is about 1% of that for doing the full reaction mechanism, allowing us to do ≈50 cases in about 1/2 the time it took to do pure Fe(111). The new leads identified with HHTCS are then validated with full mechanistic studies.For Fe(111), we predict three high-performance dopants that strongly prefer the second layer: Co with a rate 8 times higher, Ni with a rate 16 times higher, and Si with a rate 43 times higher, at 400 °C and 20 atm. We also found four dopants that strongly prefer the top layer and improve performance: Pt or Rh 3 times faster and Pd or Cu 2 times faster. For Fe(211), the best dopant was found to be second-layer Co with a rate 3 times faster than that for the undoped surface.The DFT/kMC data were used to predict reshaping of the catalyst particles under reaction conditions and how to tune dopant content so as to maximize catalytic area and thus activity. Finally, we show how to validate our mechanistic modeling via a comparison between theoretical and experimental operando spectroscopic signatures.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.accounts.1c00789.Schematic depiction of the bcc surface structures here investigated also showing 4-fold binding sites (PDF)This article has not yet been cited by other publications.

Catalytic Behavior of K-doped Fe/MgO Catalysts for Ammonia Synthesis Under Mild Reaction Conditions

Ammonia Synthesis Via Nitrogen-Coupled Methane Conversion at Ambient Temperature and Plasma Conditions

Regulating Intermediate Adsorption and H2O Dissociation on a Diatomic Catalyst to Promote Electrocatalytic Nitrate Reduction to Ammonia

Barium-doped iron nanoparticles supported on MgO as an efficient catalyst for ammonia synthesis under mild reaction conditions

Highly Efficient K-Fe/C Catalysts Derived from Metal-Organic Frameworks Towards Ammonia Synthesis

Agglomeration Suppression of a Fe-Supported Catalyst and its Utilization for Low-Temperature Ammonia Synthesis in an Electric Field

Discovering the Remarkable Denox Activity and Anti-K Poisoning of MnFeOx/H-Beta Composite Catalyst

Fe-based Catalyst Derived from MgFe-LDH: Very Efficient Yet Simply Obtainable for Hydrogen Production Via Ammonia Decomposition

Reaction Mechanisms, Kinetics, and Improved Catalysts for Ammonia Synthesis from Hierarchical High Throughput Catalyst Design

Potassium Promoted Ferrocene/Graphene for Ammonia Synthesis

Fabrication of BaO-promoted Cobalt Catalyst Incorporated into Carbon Framework by Citric Acid Sol-gel Method for Ammonia Synthesis

High-ammonia selective metal-organic framework-derived Co-doped Fe/Fe<sub>2</sub>O<sub>3</sub> catalysts for electrochemical nitrate reduction

Elucidating the role of potassium addition on the surface chemistry and catalytic properties of cobalt catalysts for ammonia synthesis

Supported Fe catalysts prepared through layered double hydroxides for primary amine synthesis by reductive amination of carbonyl compounds

Mechanocatalytic Synthesis of Ammonia: State of the Catalyst During Reaction and Deactivation Pathway

Enhancing Ammonia Synthesis on Co3Mo3N via Metal Support Interactions on a Single‐crystalline MgO Support

Enhanced Photofixation of Dinitrogen to Ammonia over a Biomimetic Metal (Fe,Mo)-Doped Mesoporous MCM-41 Zeolite Catalyst under Ambient Conditions

Barium Hydride-Mediated Nitrogen Transfer and Hydrogenation for Ammonia Synthesis: A Case Study of Cobalt

Promotional effect of aluminum doping on the sulfated Fe2O3 catalyst in selective catalytic reduction of NO with NH3

NO hydrogenation to NH3 over FeCu/TiO2 catalyst with improved activity

A Graphene Oxide‐supported PdCu Catalyst for Enhanced Electrochemical Synthesis of Ammonia