Abstract:Advanced Li-ion batteries adopting new cathode chemistries are required for the successful widespread transition to electric vehicles (EVs) and renewable energy sources, aiming for high energy density, long cycle life, and good rate capability. Commercial candidates for EV batteries include Ni-rich Li(Ni x Mn y Co 1−x-y )O 2 (NMC) cathodes, with Ni:Mn:Co ratios of 8:1:1 (NMC811) and higher. These are favored because of their high specific capacity (~ 200 mAh g -1 )and reduced cobalt content. Despite all of the advantages, these materials suffer from a range of degradation modes, many of which are associated with the redox and crystallographic behavior at high states of charge. In particular, Ni-rich cathodes suffer from several limitations, such as rapid capacity fade in comparison to NMC stoichiometries with lower Ni content. In addition, they also have a lower onset voltage for oxygen release and subsequent surface reconstruction leading to the formation of spinel and rock salt phases which impede (de)lithiation and therefore the achievable capacity of the cell. 1 Crystallographic properties of electrode materials are intrinsically linked to the electrochemical performance of the cell. NMC materials suffer from anisotropic changes in the crystal structure during cycling which induces strain and leads to issues such as crack formation, expediting degradation. One method to tackle capacity fade is to switch to single-crystal morphologies (particle size 1-3 μm) which have better mechanical stability than conventional polycrystalline morphologies (secondary agglomerate particles ~ 10 μm made up of primary particles which are 100 nm – 1 μm in size) and have less propensity to form extensive rock-salt layers. It is thought that the single-crystal morphology helps to reduce stress in the material as the anisotropic stress in polycrystalline cathodes is concentrated at grain boundaries. However, there is still a limited understanding of the subtle mechanistic differences between the two materials during cycling. 2 A multi-scale approach is required to gain a more comprehensive understanding of the degradation mechanisms at play and how they initiate and propagate. In this work, synchrotron diffraction methods were employed at the crystal, particle and cell scale using a variety of techniques including in-situ Bragg Coherent Diffraction Imaging (BCDI), 3D-XRD and operando high-resolution XRD. Intra-particle, inter-particle and electrode level heterogeneities were observed during cycling, both in pristine and aged samples. It is believed that these heterogeneities accelerate the loss of performance at the cell level by inducing crack formation which can then be observed in X-ray computed tomography data acquired in simultaneous lab studies. The overarching goal of these investigations is to add to the understanding of complex degradation mechanisms for Ni-rich layered transition metal oxide cathodes, ultimately aiding in the informed development of future battery electrode materials. References: 1] Xu, C. et al., Phase Behaviour during Electrochemical Cycling of Ni‐Rich Cathode Materials for Li‐Ion Batteries. Adv. Energy Mater. 2021, 11, 2003404. 2] Yin, S. et al., Fundamental and solutions of microcracks in Ni-rich layered oxide cathode materials of lithium-ion batteries. Nano Energy, 2021, 83, 105854.

Insights into soft short circuit-based degradation of lithium metal batteries

Transient Short Circuit-Based Degradation of Lithium and Sodium Anode-Free Batteries

Detection, Analysis, and Behavior of Soft-Shorts in Solid-State Batteries

Impact of Low Temperature Exposure on Lithium-Ion Batteries: A Multi-Scale Study of Performance Degradation, Predictive Signals and Underlying Mechanisms

Nondestructively Visualizing and Understanding the Mechano‐Electro‐chemical Origins of “soft Short” and “creeping” in All‐Solid‐State Batteries

Multiscale correlative imaging reveals sequential and heterogeneous degradations in fast-charging batteries

Quantifying Heterogeneous Degradation Pathways and Deformation Fields in Solid State Batteries

Decoding Internal Stress‐Induced Micro‐Short Circuit Events in Sulfide‐Based All‐Solid‐State Li‐Metal Batteries via Operando Pressure Measurements

Dynamic Lithium Distribution upon Dendrite Growth and Shorting Revealed by Operando Neutron Imaging

Probing Degradation in Lithium Ion Batteries With On‐Chip Electrochemistry Mass Spectrometry

Voltage Noise Failure Induced by Li Dendritic Micro‐Penetration in All‐Solid‐State Li‐Metal Battery with Composite Solid Electrolyte

Identifying Pitfalls in Lithium Metal Battery Characterization

Fast Diagnosis of Failure Mechanisms and Lifetime Prediction of Li Metal Batteries

Early Failure of Lithium–Sulfur Batteries at Practical Conditions: Crosstalk between Sulfur Cathode and Lithium Anode

Diagnosing and correcting anode-free cell failure via electrolyte and morphological analysis

Ultrasonic assessment of aging in lithium metal pouch cells

Non-Invasive Detection of Lithium-Metal Battery Degradation

Understanding the Degradation Mechanisms of Lithium Ion Batteries Using in-Situ Multi-Scale Diffraction Techniques

Detrimental Effects of Chemical Cross-Talk in Rechargeable Lithium Metal Batteries

Visualising the Effect of Areal Current Density on the Performance and Degradation of Lithium Sulfur Batteries Using Operando Optical Microscopy

Li-ion Battery Separators, Mechanical Integrity and Failure Mechanisms Leading to Soft and Hard Internal Shorts