Abstract:Statement of problem: Implant-supported rehabilitations are an increasingly frequent practice to replace lost teeth. Before clinical application, all implant components should demonstrate suitable durability in laboratory studies, through fatigue tests. Objective: The purpose of this in vitro study was to evaluate the integrity and wear of implant components using SEM, and to assess the axial displacement of the implant–abutment assembly by Micro-CT, in different implant connections, after three distinct mechanical requests. Materials and methods: Four KLOCKNER implants (external connection SK2 and KL; and internal connection VEGA and ESSENTIAL) were submitted to three different mechanical requests: single tightening, multiple tightening, and multiple tightening and cyclic loading (500 N × 100 cycles). A total of 16 samples were evaluated by SEM, by the X-ray Bragg–Brentano method to obtain residual stresses, and scratch tests were realized for each surface and Micro-CT (4 control samples; 4 single tightening; 4 multiple tightening; 4 multiple tightening and cyclic loading). All dental implants were fabricated with commercially pure titanium (grade 3 titanium). Surface topography and axial displacement of abutment into the implant, from each group, were evaluated by SEM and Micro-CT. Results: In the manufacturing state, implants and abutments revealed minor structural changes and minimal damage from the machining process. The application of the tightening torque and loading was decisive in the appearance and increase in contact marks on the faces of the hexagon of the abutment and the implant. Vega has the maximum compressive residual stress and, as a consequence, higher scratch force. The abutment–implant distances in SK2 and KL samples did not show statistically significant differences, for any of the mechanical demands analyzed. In contrast, statistically significant differences were observed in abutment–implant distance in the internal connection implants Vega and Essential. Conclusions: The application of mechanical compression loads caused deformation and contact marks in all models tested. Only internal connection implants revealed an axial displacement of the abutment into the implant, but at a general level, a clear intrusion of the abutment into the implant could only be confirmed in the Essential model, which obtained its maximal axial displacement with cyclic loading.

Imaging Retinal Vascular Changes in Uveitis

Assessment of stress shielding around a dental implant for variation of implant stiffness and parafunctional loading using finite element analysis

Stress shielding at the bone-implant interface: influence of surface roughness and of the bone-implant contact ratio

Surface Treatments and Residual Stress: Assessing the Implications for Biocompatibility in Titanium Implants

SEM Analysis and Micro-CT Evaluation of Four Dental Implants after Three Different Mechanical Requests—In Vitro Study

Biomechanical Fatigue Behavior of a Dental Implant Due to Chewing Forces: A Finite Element Analysis

Design Factors of Ti-Base Abutments Related to the Biomechanics Behavior of Dental Implant Prostheses: Finite Element Analysis and Validation via In Vitro Load Creeping Tests

Influence of Restorative Material on the Distribution of Loads to the Bone in Hybrid Abutment Crowns-In Vitro Study

Influence of prosthetic index structures and implant materials on stress distribution in implant restorations: a three-dimensional finite element analysis

Influence of surface coatings on the stress distribution by varying friction contact at implant-bone interface using finite element analysis

Effect of Different Implant Designs on Strain and Stress Distribution under Non-Axial Loading: A Three-Dimensional Finite Element Analysis

A 3D Finite Element Analysis Model of Single Implant-Supported Prosthesis under Dynamic Impact Loading for Evaluation of Stress in the Crown, Abutment and Cortical Bone Using Different Rehabilitation Materials

Effect of different biocompatible implant materials on the mechanical stability of dental implants under excessive oblique load

Fatigue Design of Dental Implant Assemblies: A Nominal Stress Approach

Progesterone potentiating effect of Dipsacus mitis D. Don for its contraceptive action in hamster.

Influence of connection design and material properties on stress distribution and fatigue lifetime of zygomatic implants: A finite element analysis

Implant-Supported Fixed Partial Prostheses With Different Prosthetic Materials: A Three-Dimensional Finite Element Stress Analysis

Observations on the mechanism of hydroxylation of cyclophosphamide by rat liver microsomes: the metabolism of cyclophosphamide-4-d2.

Influence of prosthesis type and material on the stress distribution in bone around implants: A 3-dimensional finite element analysis

Clinical experience with docetaxel for Chinese breast cancer patients: Hematological toxicity profiles

Effect of different occlusal materials on peri-implant stress distribution with different osseointegration condition: A finite element analysis