Nursing and pre-registration nursing education under the spotlight again.

D. Jackson,J. Daly

DOI: https://doi.org/10.1016/J.COLEGN.2007.11.004

IF: 1.807

2008-02-01

Collegian

Abstract:

What problem does this paper attempt to address?

Laboratory and on-road testing for brake wear particle emissions: a review

Maria Luisa Feo,Marco Torre,Patrizio Tratzi,Francesca Battistelli,Laura Tomassetti,Francesco Petracchini,Ettore Guerriero,Valerio Paolini

DOI: https://doi.org/10.1007/s11356-023-29229-7

Abstract:Brake wear emission is a significant contributor to vehicle-related particulate matter, especially in areas with high traffic density and braking frequency. Only recently, non-exhaust emissions from car brake wear have been regulated under Euro 7 regulation, which introduces emission limits for both brake and tires. It also introduces a standard brake particle assessment procedure which includes sampling procedure and measurement techniques defined in the Global Technical Regulation on brakes from light-duty vehicles up to 3.5 t. Over the years, various experimental setups have been tried leading to non-comparable results. The brake wear particle emissions, expressed as emission factors, are mostly estimated as particle mass or particle number and described using different units (e.g., mg/stop brake, mg/km brake; particle number/cm3) making the comparison between studies very difficult. The aim of the present literature review is to present the state-of-the-art of different experimental methods tuned for assessing brake wear emissions, including electric vehicles. The experiments are carried in close, semi-closed, and open systems, and depending on the experimental design, different sampling methods are applied to reduce particle transport loss and guarantee the efficiency of the particle sampling. Driving condition (e.g., speed and applied pressure), formulation of brake materials, and friction temperature have been found to strongly affect the emission characteristics of brake particles, and this needs to be considered when designing study procedures. The findings reported in this review can be beneficial to policy makers and researchers.
Measurement and Analysis of Brake and Tyre Particle Emissions from Automotive Series Components for High-Load Driving Tests on a Wheel and Suspension Test Bed

Martin Kupper,Ludwig Schubert,Manfred Nachtnebel,Hartmuth Schröttner,Michael Peter Huber,Peter Fischer,Alexander Bergmann

DOI: https://doi.org/10.3390/atmos15040430

IF: 3.11

2024-03-30

Atmosphere

Abstract:A current challenge in realising clean road transport is non-exhaust emissions. Important advances regarding measurement systems, including well-defined characterisation techniques, as well as regulation, will be made in the next few years. In this work, we present the detailed results of particle emission analyses, consisting of aerosol (size distribution, particle number (PN), and mass (PM)) and electron microscopy (EM) measurements, under different load conditions on a test bed for a wheel suspension and brakes. Standard tyres and brakes from serial production were tested with a high-load driving cycle, while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS, and a GRIMM OPS. Furthermore, samples were analysed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with an SMPS, with peaks at 20nm and around 400nm. The results of an EM analysis of >1400 single particles from the electrostatic sampler match the PSD results. The EM analysis also showed ultrafine particles, mainly containing O, Fe, Si, Ba, Mg, and S, and also fractal particles with high-C fractions. Our results suggest, in agreement with the previously published literature, that particulate emissions are related to the brake disc temperature and occur in significant amounts above a threshold temperature.

environmental sciences,meteorology & atmospheric sciences
Gaseous emissions from brake wear can form secondary particulate matter

Anil Patel,Sneha Aggarwal,Lucas Bard,Olivier Durif,Micol Introna,Ana Teresa Juárez-Facio,Minghui Tu,Karine Elihn,Barbara Nozière,Ulf Olofsson,Sarah S. Steimer

DOI: https://doi.org/10.1038/s41598-024-74378-5

IF: 4.6

2024-10-07

Scientific Reports

Abstract:Road traffic is an important source of urban air pollutants. Due to increasingly strict controls of exhaust emissions from road traffic, their contribution to the total emissions has strongly decreased over time in high-income countries. In contrast, non-exhaust emissions from road vehicles are not yet legislated and now make up the major proportion of road traffic emissions in many countries. Brake wear, which occurs due to friction between brake linings and their rotating counterpart, is one of the main non-exhaust sources contributing to particle emissions. Since the focus of brake wear emission has largely been on particulate pollutants, little is currently known about gaseous emissions such as volatile organic compounds from braking and their fate in the atmosphere. This study investigates the oxidative ageing of gaseous brake wear emissions generated with a pin-on-disc tribometer, using an oxidation flow reactor. The results demonstrate, for the first time, that the photooxidation of gaseous brake wear emissions can lead to formation of secondary particulate matter, which could amplify the environmental impact of brake wear emissions.

multidisciplinary sciences
Unrecognized volatile and semi-volatile organic compounds from brake wear

V Perraud,D R Blake,L M Wingen,B Barletta,P S Bauer,J Campos,M J Ezell,A Guenther,K N Johnson,M Lee,S Meinardi,J Patterson,E S Saltzman,A E Thomas,J N Smith,B J Finlayson-Pitts

DOI: https://doi.org/10.1039/d4em00024b

2024-05-22

Abstract:Motor vehicles are among the major sources of pollutants and greenhouse gases in urban areas and a transition to "zero emission vehicles" is underway worldwide. However, emissions associated with brake and tire wear will remain. We show here that previously unrecognized volatile and semi-volatile organic compounds, which have a similarity to biomass burning emissions are emitted during braking. These include greenhouse gases or, these classified as Hazardous Air Pollutants, as well as nitrogen-containing organics, nitrogen oxides and ammonia. The distribution and reactivity of these gaseous emissions are such that they can react in air to form ozone and other secondary pollutants with adverse health and climate consequences. Some of the compounds may prove to be unique markers of brake emissions. At higher temperatures, nucleation and growth of nanoparticles is also observed. Regions with high traffic, which are often disadvantaged communities, as well as commuters can be impacted by these emissions even after combustion-powered vehicles are phased out.
A Practical Approach for On-Road Measurements of Brake Wear Particles from a Light-Duty Vehicle

Jon Andersson,Louisa J. Kramer,Michael Campbell,Ian Marshall,John Norris,Jason Southgate,Simon de de Vries,Gary Waite

DOI: https://doi.org/10.3390/atmos15020224

IF: 3.11

2024-02-14

Atmosphere

Abstract:Brake wear particles are generated through frictional contact between the brake disc or brake drum and the brake pads. Some of these particles may be released into the atmosphere, contributing to airborne fine particulate matter (PM2.5). In this study, an onboard system was developed and tested to measure brake wear particles emitted under real-world driving conditions. Brake wear particles were extracted from a fixed volume enclosure surrounding the pad and disc installed on the front wheel of a light-duty vehicle. Real-time data on size distribution, number concentration, PM2.5 mass, and the contribution of semi-volatiles were obtained via a suite of instruments sub-sampling from the constant volume sampler (CVS) dilution tunnel. Repeat measurements of brake particles were obtained from a 42 min bespoke drive cycle on a chassis dynamometer, from on-road tests in an urban area, and from braking events on a test track. The results showed that particle emissions coincided with braking events, with mass emissions around 1 mg/km/brake during on-road driving. Particle number emissions of low volatility particles were between 2 and 5 × 109 particles/km/brake. The highest emissions were observed under more aggressive braking. The project successfully developed a proof-of-principle measurement system for brake wear emissions from transient vehicle operation. The system shows good repeatability for stable particle metrics, such as non-volatile particle number (PN) from the solid particle counting system (SPCS), and allows for progression to a second phase of work where emissions differences between commercially available brake system components will be assessed.

environmental sciences,meteorology & atmospheric sciences
Wear and environmental aspects of composite materials for automotive braking industry

Vaclav Roubicek,Helena Raclavska,Dagmer Juchelkova,Peter Filip

DOI: https://doi.org/10.1016/j.wear.2007.09.006

IF: 4.695

2008-06-01

Wear

Abstract:Braking is accompanied with the release of a variety of particulates. More than 230 million vehicles are on the roads and over 16 million new vehicles are sold in the USA each year [1]. Brake linings are complex composites typically formulated of more than 10 constituents, and more than 3000 different materials were used in different brands [2]. Use of asbestos has been suppressed because of health implications [3], however, it is not clear what impact the currently used materials have. In this research, the collected wear debris as well as the friction layers were analyzed. The adopted SAE J2430 friction test is frequently used in the USA for evaluating the performance of brakes. Combination of light and electron microscopy supported by energy dispersive microanalysis, grazing angle X-ray diffraction, and atomic force microscopy allow successful analysis of released matter. It was shown that nanoparticles of newly formed materials are being released during wear process and it is suggested to initiate additional research addressing possible impact of these species on the environment. The released amounts of CO2 can be correlated with wear of brake lining materials.

engineering, mechanical,materials science, multidisciplinary
Direct measurement of brake and tire wear particles based on real-world driving conditions

Qijun Zhang,Tiange Fang,Zhengyu Men,Ning Wei,Jianfei Peng,Tianqiang Du,Xinfeng Zhang,Yao Ma,Lin Wu,Hongjun Mao

DOI: https://doi.org/10.1016/j.scitotenv.2023.167764

IF: 9.8

2023-10-13

The Science of The Total Environment

Abstract:With implementing vehicle emission control policies, tailpipe particulate emissions have been gradually controlled, and the relative contribution of non-tailpipe particulate emissions, such as brake and tire wear, has further increased. A unified and scientific method for sampling non-tailpipe particulate matter (PM) emissions is essential to improve the accuracy of the emission characteristics and factors. This study proposes a novel sampling method based on real-world driving conditions to obtain information on emissions and extract characteristic conditions for tire and brake pad wear. We extracted 200 representative braking segments for simulation experiments based on road type, initial and final velocities, temperature, and deceleration rate. Two standard test cycles to simulate the tire wear conditions of the front and rear wheels were constructed based on velocity, lateral, and vertical forces. Under the real-world driving condition test cycle, the emission factors of PM 2.5 and PM 10 for brake wear particles of passenger vehicles were 2.66 mg/km and 11.65 mg/km, respectively. In contrast, the emission factors of PM 2.5 and PM 10 for tire wear particles were 0.21 mg/km and 1.27 mg/km, respectively. Moreover, this study provides insights and basic data for localizing and improving the emission model, which can enhance its applicability and accuracy.

environmental sciences
Airborne Brake Wear Emissions from a Battery Electric Vehicle

Linda Bondorf,Lennart Köhler,Tobias Grein,Fabius Epple,Franz Philipps,Manfred Aigner,Tobias Schripp

DOI: https://doi.org/10.3390/atmos14030488

IF: 3.11

2023-03-02

Atmosphere

Abstract:Although traffic exhaust emissions in Europe have been drastically reduced, airborne particle emissions caused by brakes and tires are still increasing with the number of vehicles. The measurement of non-exhaust emissions is an emerging technological challenge. We present a custom measurement setup to investigate the brake- and tire-wear emissions of an in-use battery electric vehicle. A separate brake housing and HEPA ventilation enabled airborne brake wear emissions to be measured under realistic conditions without external influences. The emission tests on a chassis dynamometer included particle number concentrations and particle size distribution for diameters of 4 nm to 10 μm. Emission indices were determined for three driving cycles: WLTC Class 3b, WLTC Brake Part 10, and a real driving cycle. Further investigations focused on emission control through regenerative braking and brake coating. Driving with regenerative braking reduced emissions by up to 89.9%, which related to the concentration of particles in the ultrafine/fine size range. Hard-metal brake coating led to a further significant reduction in emissions of up to 78.9%. The results point the way to future RDE measurement of non-exhaust emissions and show the potential of regenerative braking and brake coating to reduce airborne brake wear emissions.

environmental sciences,meteorology & atmospheric sciences
Investigations of airborne tire and brake wear particles using a novel vehicle design

Manuel Löber,Linda Bondorf,Tobias Grein,Sven Reiland,Steffen Wieser,Fabius Epple,Franz Philipps,Tobias Schripp

DOI: https://doi.org/10.1007/s11356-024-34543-9

IF: 5.8

2024-08-30

Environmental Science and Pollution Research

Abstract:Non-exhaust emissions have become an increasingly important issue as their levels continue to rise and the health effects of particulate matter (PM) are more widely discussed. To address this issue, a vehicle demonstrator with integrated emission reduction of tires and brakes was developed as part of the Zero Emission Drive Unit Generation-1 (ZEDU-1) project. This novel concept includes the removal of tire road wear particles (TRWP) with a strong ventilation/filtering system and an enclosed multi-disk brake, making it a suitable tool for the investigation of non-exhaust emissions. Particle number (PN) and particle size distribution (PSD) measurements down to 2.5 nm were performed on a chassis dynamometer and on a test track. Due to the low background concentrations on the chassis dynamometer, it is possible to distinguish between tire and brake wear and to characterize even a small number of particle emissions. It could be shown that about 30 % less particles are emitted by the vehicle, when using the novel multi-disk brake instead of the conventional brake. The highest TRWP emissions were collected during acceleration and harsh braking. Characterization of the collected particles using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) revealed diverse particle shapes and differences between particles generated on the dynamometer and on a test track.

environmental sciences
Brake wear (nano)particle characterization and toxicity on airway epithelial cells in vitro

Chloé Puisney,Evdokia K. Oikonomou,Sophie Nowak,Alexandre Chevillot,Sandra Casale,Armelle Baeza-Squiban,Jean-François Berret

DOI: https://doi.org/10.48550/arXiv.1803.01426

2018-03-04

Applied Physics

Abstract:Particulate air pollution results from different sources, among which those related to road traffic have a significant impact on human health. Combustion-derived particles emitted by thermal engines have been incriminated and are now better controlled. In contrast, non-exhaust emission sources related to car wear and degradation processes are not yet regulated. Here we report on brake wear particles (BWP) harvested in two test facilities operating in France, providing samples from different braking systems and driving/testing conditions. Using a combination of light scattering, X-ray fluorescence, optical and electron microscopy, the particle size and elemental composition are revealed. The BWP are shown to be in the nano- to micrometer range and to have a low carbonaceous content (6%), iron and copper being the main components (> 40%). To evaluate the toxicity potential of its nano-sized fraction, brake wear nanoparticles are isolated by sonication, filtration and ultra-centrifugation techniques, leading to stable colloidal dispersions. A significant outcome of this study is that the nano-sized fraction represents 26% by mass of the initial BWP. Human bronchial epithelial cells (Calu-3) are used as relevant target cells to investigate their cytotoxicity. We observe a clear short-term loss of viability associated to reactive oxygen species generation, but with limited pro-inflammatory effects. On an actual cell-deposited mass-dose basis, the cytotoxicity of the nanosized fraction is similar to that of BWP, suggesting that the cytotoxicity is particle size independent. To conclude, brake wear dust contains substantial amount of metallic nanoparticles exhibiting toxicity for lung cells, and should warrant further consideration.
Assessing the brake particle emissions for sustainable transport: A review

Yachao Wang,Hang Yin,Zhengjun Yang,Sheng Su,Lijun Hao,Jianwei Tan,Xin Wang,Zhihui Niu,Yunshan Ge,Yachao Wang,Hang Yin,Zhengjun Yang,Sheng Su,Lijun Hao,Jianwei Tan,Xin Wang,Zhihui Niu,Yunshan Ge

DOI: https://doi.org/10.1016/j.rser.2022.112737

IF: 16.799

2022-10-01

Renewable and Sustainable Energy Reviews

Abstract:Particles emitted during braking account for a significant proportion of transport-related particles. The brake particles are still beyond supervision because no mandatory regulations were introduced to control the brake particle emissions. Many studies have been conducted about the brake particles, but the materials & methods used by these studies vary a lot, thus reducing the result comparability among these studies. This paper reviewed brake particle emissions from four aspects: experimental methods, emission characteristics, influencing factors, and future works. Six experimental methods corresponding to different application scenarios are summarized, and these methods require different modifications, skills, and expenses. Whatever the experimental methods, the sampling method needs careful design to reduce the particle transport loss and to ensure particle sampling efficiency. The reported brake particle emissions could exceed the sixth stage exhaust emission regulation (both EU and China), depending on the test procedures, friction materials, and data processing. The brake particle covers a broad size distribution (from a few nanometers to tens of microns), and more studies are needed about its physicochemical characteristics. The friction materials, system running-in, and friction temperature will significantly affect the brake particle emission characteristics, and these factors should be considered when designing the study procedure. The patterns about gaseous emission and non-brake particle emission need more attention, as these patterns might be helpful to understand the brake particle emission characteristics. Some filter&collection-based brake particle after-treatments have also been invented. Future studies should focus on the homogeneous test procedure, mechanism analysis, after-treatment, and non-airborne wear et al.

energy & fuels,green & sustainable science & technology
Investigation of Brake Emissions of Different Brake Pad Materials with Regard to Particle Mass (PM) and Particle Number (PN)

Andreas Paulus

DOI: https://doi.org/10.1007/978-3-662-59825-2_11

2019-01-01

Proceedings

Abstract:Non-exhaust PM10 emissions are coming increasingly into focus of both regulation and media coverage. This will in coming years pose a challenge to the mobility sector as a whole and to the automobile industry in particular. To master this challenge, an in depth knowledge of the underlying processes of particle generation and emission is needed. As a contribution to this effort, the present study investigates the influence of different friction materials and disc types on brake emissions. It show that a well-performed brake emission measurement on a brake dynamometer can provide valuable information about both basic influencing factors and material-specific emission behavior. The results clearly indicate a correlation between the mass of PM10 emissions and total wear as well as a temperature dependency of the number of emitted particles (PN emissions) for grey cast iron brake discs. It is shown that coated discs have the ability to significantly reduce PN emissions especially in the small particle size range. The presented measurement method and evaluation strategy enables future friction material development that is aiming at low emission brake systems.
A new method to assess vehicle airborne non-exhaust particles: Principle, application and emission evaluation

Yachao Wang,Jiachen Li,Hang Yin,Zhengjun Yang,Chongzhi Zhong,Jiaxin Sun,Yuekun Hu,Zhenguo Li,Yuankai Shao,Li Zhang,Tianqiang Du,Yunshan Ge

DOI: https://doi.org/10.1016/j.apenergy.2023.121942

IF: 11.2

2023-09-20

Applied Energy

Abstract:A method that could assess the whole vehicle non-exhaust particle (NEP) emission from the whole vehicle level was proposed by combining sealed housing with the chassis dynamometer. The intake and exhaust systems were connected to the out of the chamber to avoid possible effects on NEP emissions. The most distinguishing feature of the proposed method is the whole vehicle assessment of the NEP. Based on the proposed method, three vehicles were tested under various conditions. The results proved that the total NEP from the US06 cycle could be four orders of magnitude higher than that of the WLTC cycle due to the higher thermal load. The transient NEP concentration is highly associated with the friction pairs' temperature, and there are two critical temperatures respectively for volatile particles and solid particles. Mechanical friction-dominated test (WLTC) tends to produce larger particles, while thermal process-dominated tests (US06) tend to emit smaller particles. Solid particles occupy <10% of the total particles, and solid particle is dominated with the size at 10– 23 nm. The higher the brake temperature, the higher the solid particle emissions (both concentration and portion). NEP emission decreases when vehicle miles travelled increase. Total NEP number emission factors could be two orders of magnitude higher than the current PN limit for exhaust particles (6*10 11 #/km). The solid particle emission factor could also be ten times higher than the current PN limit. O and Fe element distribution matches well with the SEM image, which means the proposed method could successfully sample the brake particles. The carbon element weight is dominated by the organic carbon, which might mean that it's the mechanical abrasion dominate the carbon mass. The top 5 dominant element during ICP/MS analysis is Si, Na, Mg, Zn, and Al.

energy & fuels,engineering, chemical
Contributions of non-tailpipe emissions to near-road PM2.5 and PM10: A chemical mass balance study

L-W Antony Chen,Xiaoliang Wang,Brenda Lopez,Guoyuan Wu,Steven Sai Hang Ho,Judith C Chow,John G Watson,Qi Yao,Seungju Yoon,Heejung Jung,L.-W. Antony Chen,Steven S.H. Ho,Judith C. Chow,John G. Watson

DOI: https://doi.org/10.1016/j.envpol.2023.122283

IF: 8.9

2023-07-01

Environmental Pollution

Abstract:As the importance of non-tailpipe particles (NTP) over tailpipe emissions from urban traffic has been increasing, there is a need to evaluate NTP contributions to ambient particulate matter (PM) using representative source profiles. The Brake and Tire Wear Study conducted in Los Angeles, California in the winter of 2020 collected 64 PM2.5 and 64 PM10 samples from 32 pairs of downwind-upwind measurements at two near-road locations (I-5 in Anaheim and I-710 in Long Beach). These samples were characterized for inorganic and organic markers and, along with locally-developed brake wear, tire wear, and road dust source profiles, subject to source apportionment using the effective-variance chemical mass balance (EV-CMB) model. Model results highlighted the dominance of resuspended dust in both PM2.5 (23-33%) and PM10 (32-53%). Brake and tire wear contributed more to PM2.5 than tailpipe exhausts (diesel + gasoline) for I-5 (29-30% vs. 19-21%) while they were comparable for I-710 (15-17% vs. 15-19%). For PM10, the brake and tire wear contributions were 2-3 times the exhaust contributions. Different fleet compositions on and near I-5 and I-710 appeared to influence the relative importance of NTP and exhaust sources. The downwind-upwind differences in source contributions were often insignificant, consistent with small and/or nearly equal impacts of adjacent highway traffic emissions on the downwind and upwind sites. The utility of sole markers, such as barium and zinc, to predict brake and tire wear abundances in ambient PM is evaluated.

environmental sciences
Chemical Assessment of Real Driving Tire and Road Wear Particles in Urban and Suburban Seoul, Korea

Sunhee Mun,Hwansoo Chong,Yunsung Lim,Sangil Kwon

DOI: https://doi.org/10.3390/su162310395

IF: 3.9

2024-11-28

Sustainability

Abstract:Extensive research about non-exhaust fine particles from tires and brakes in vehicles has been reported, focusing on the significant effects on air pollution and human harm. Significant investigations are still needed in determining the cause of influence on the environment and human health. The regulations on emissions have been discussed in earnest, starting with the introduction of brake wear particle emission standards in Euro 7. Various indoor and outdoor experiments have been conducted, such as analysis of the amount of wear on tires and brakes, and analysis of the physical and chemical properties of fine particles, and the effect of non-exhaust fine wear particles on the atmosphere and human health, as fundamental data for the introduction of emission standards and the development of low-wear tires and brakes to meet regulations. Recently, international standardized indoor experimental methods for brakes have been announced, and indoor and outdoor experimental methods for tires have been continuously studied to develop international standardized methods. In particular, tire and road wear particles, including brake wear particles, are usually mixed with each other in the non-exhaust particles from a vehicle driving on real roads, and in-depth research is being performed on their accurate classification and characteristic analysis. In this study, the characteristics of the volatile organic compounds and marker substances for tire and tire and road wear particles were analyzed. A system was installed on the vehicle to collect non-exhaust wear fine particles from the vehicle running on two different roads, urban and suburban, of the Seoul area, and the proving ground road. The specific findings are as follows: (1) From the chemical analysis of the volatile organic compounds, high n-hexane and n-dodecane were measured in the tire–road-wear particles. (2) The volatile organic compound species in the PM2.5 (aerodynamic diameter ≤ 2.5 μm) increased as the vehicle velocity increased. (3) For the PM10 (aerodynamic diameter ≤ 10 μm), high volatile organic compound species were recorded at 40 km/h of the vehicle velocity. (4) This study also revealed that higher vinylcyclohexene and dipentene were measured in the particle size below 10 μm than those in PM2.5.

environmental sciences,environmental studies,green & sustainable science & technology
Dynamometric Investigation on Airborne Particulate Matter from Automobile Brake: Impact of Disc Materials on Brake Emission Factor

Mu Hyeok Jeong,Won Cheol Shin,Yoon-Suk Oh,Jungju Lee,Seung Hun Huh,Jae-Hwan Pee,Hyungjo Seo,Ho Jang,Jong-Young Kim

DOI: https://doi.org/10.3390/lubricants11120526

2023-12-11

Lubricants

Abstract:In this work, we evaluated the impact of disc rotors of gray cast iron (GCI), nitrocarburized (NC), and superhard ceramic-coated (SCC) GCI on the brake wear PM emissions of passenger vehicles using dynamometric measurements. The brake emission factor (BEF) of the SCC was greatly reduced by more than a factor of 1/5 compared with those for the GCI and NC for both low-steel and non-steel friction materials. Surface topological and microstructural analyses confirmed that more severe wear was pronounced for the NC rotor compared with the SCC, as evidenced by large concave pits in the wear tracks. Analysis of the size-classified airborne PM suggests that reduced micron-sized particles, which originated from the GCI disc, were responsible for the lower BEF due to the increased hardness of the SCC.
Heavy metals from non-exhaust vehicle emissions in urban and motorway road dusts

Ewa Adamiec,Elżbieta Jarosz-Krzemińska,Robert Wieszała

DOI: https://doi.org/10.1007/s10661-016-5377-1

IF: 3.307

2016-05-26

Environmental Monitoring and Assessment

Abstract:The main sources of non-exhaust vehicular emissions that contribute to road dust are tire, brake and clutch wear, road surface wear, and other vehicle and road component degradation. This study is an attempt to identify and investigate heavy metals in urban and motorway road dusts as well as in dust from brake linings and tires. Road dust was collected from sections of the A-4 motorway in Poland, which is part of European route E40, and from urban roads in Katowice, Poland. Dust from a relatively unpolluted mountain road was collected and examined as a control sample. Selected metals Cd, Cr, Cu, Ni, Pb, Zn, Fe, Se, Sr, Ba, Ti, and Pd were analyzed using inductively coupled plasma-mass spectrometry, inductively coupled plasma (ICP)-optical emission spectroscopy, and atomic absorption spectroscopy on a range of size-fractionated road dust and brake lining dust (<20, 20–56, 56–90, 90–250, and >250 μm). The compositions of brake lining and tire dust were also investigated using scanning electron microscopy-energy-dispersive spectroscopy. To estimate the degree of potential environmental risk of non-exhaust emissions, comparison with the geochemical background and the calculations of geo-accumulation indices were performed. The finest fractions of urban and motorway dusts were significantly contaminated with all of the investigated metals, especially with Ti, Cu, and Cr, which are well-recognized key tracers of non-exhaust brake wear. Urban dust was, however, more contaminated than motorway dust. It was therefore concluded that brake lining and tire wear strongly contributed to the contamination of road dust.

environmental sciences
New insights into reducing airborne particle emissions from brake materials: Grooved textures on brake disc surface

Ming-xue Shen,Han-xin Li,Jun-Hua Du,De-Hui Ji,Shao-peng Liu,Ye-long Xiao

DOI: https://doi.org/10.1016/j.triboint.2022.107721

IF: 5.62

2022-10-01

Tribology International

Abstract:Airborne particles from brake systems have been widely recognised as a great contributor of particulate matter (PM) in railway environments, such as micro- and nano-size airborne particles. Increasing attention is being paid to airborne particles due to their potential for adverse health effects. In the brake system, particulate matter and wear debris mostly come from the wear of brake pair materials. Reducing-friction and anti-wear effect can be achieved by means of a reasonable grooved texture. In this paper, evaluation of friction, wear and particle emission behaviour of commercial brake pads for high-speed trains were studied using a pin-on-disc tribometer. Effect of grooved textures on the characteristics of airborne particles and deposited debris particles, as well as the wear behaviour of brake materials, was investigated on the basis of the brake discs with different numbers and angles of grooved textures. Results show that the grooved texture on the brake disc can effectively restrain airborne brake particulate emissions, particularly particles in the size range of 1.0 μm ≤ d ≤ 5.0 μm. Compared with the brake discs with the grooved texture, the size of the abrasive particles generated in the non-textured test group become smaller, irregular agglomerates of wear debris are more easily formed, and the debris particles are mostly lamellar with smooth surfaces and sharp edges. The wear rate of the pins against the brake disc with the grooved texture slightly increases, but the surface wear of the brake discs is effectively mitigated. In comparison with the number of grooves, the angle of the grooved texture has a more significant effect on the particle emission and wear behaviour of the brake disc. Additionally, the brake disc with 6 grooves, as well as the angle of the grooves face the friction direction, exhibits the best comprehensive performance.

engineering, mechanical
Biological response of an in vitro human 3D lung cell model exposed to brake wear debris varies based on brake pad formulation

Hana Barosova,Savvina Chortarea,Pavlina Peikertova,Martin J D Clift,Alke Petri-Fink,Jana Kukutschova,Barbara Rothen-Rutishauser

DOI: https://doi.org/10.1007/s00204-018-2218-8

Abstract:Wear particles from automotive friction brake pads of various sizes, morphology, and chemical composition are significant contributors towards particulate matter. Knowledge concerning the potential adverse effects following inhalation exposure to brake wear debris is limited. Our aim was, therefore, to generate brake wear particles released from commercial low-metallic and non-asbestos organic automotive brake pads used in mid-size passenger cars by a full-scale brake dynamometer with an environmental chamber simulating urban driving and to deduce their potential hazard in vitro. The collected fractions were analysed using scanning electron microscopy via energy-dispersive X-ray spectroscopy (SEM-EDS) and Raman microspectroscopy. The biological impact of the samples was investigated using a human 3D multicellular model consisting of human epithelial cells (A549) and human primary immune cells (macrophages and dendritic cells) mimicking the human epithelial tissue barrier. The viability, morphology, oxidative stress, and (pro-)inflammatory response of the cells were assessed following 24 h exposure to ~ 12, ~ 24, and ~ 48 µg/cm2 of non-airborne samples and to ~ 3.7 µg/cm2 of different brake wear size fractions (2-4, 1-2, and 0.25-1 µm) applying a pseudo-air-liquid interface approach. Brake wear debris with low-metallic formula does not induce any adverse biological effects to the in vitro lung multicellular model. Brake wear particles from non-asbestos organic formulated pads, however, induced increased (pro-)inflammatory mediator release from the same in vitro system. The latter finding can be attributed to the different particle compositions, specifically the presence of anatase.
Light-Duty Vehicle Brake Emission Factors

Barouch Giechaskiel,Theodoros Grigoratos,Panagiota Dilara,Traianos Karageorgiou,Leonidas Ntziachristos,Zissis Samaras

DOI: https://doi.org/10.3390/atmos15010097

IF: 3.11

2024-01-12

Atmosphere

Abstract:Particulate Matter (PM) air pollution has been linked to major adverse health effects. Road transport still contributes significantly to ambient PM concentrations, but mainly due to the non-exhaust emissions from vehicles. For the first time worldwide, limits for non-exhaust emissions have been proposed by the European Union for the upcoming Euro 7 step. For these reasons, interest in brake emissions has increased in the past few years. Realistic emission factors are necessary to accurately calculate the contribution of brake emissions to air pollution but also to estimate the emissions reduction potential of new or existing technologies and improved brake formulations. This paper reviews emission factors from light-duty vehicles reported in the literature, with a focus on those that followed the recently introduced Global Technical Regulation (GTR 24) methodology on brakes in light-duty vehicles. Reduction efficiencies of non-asbestos organic (NAO) pads, brake dust filters, ceramic discs, coated discs, and regenerative braking are also discussed. Finally, the emission factors are compared with roadside measurements of brake emissions and emission inventories worldwide. The findings of this study can be used as an input in emission inventories to estimate the contribution of brakes to air pollution.

environmental sciences,meteorology & atmospheric sciences

Nursing and pre-registration nursing education under the spotlight again.

Laboratory and on-road testing for brake wear particle emissions: a review

Measurement and Analysis of Brake and Tyre Particle Emissions from Automotive Series Components for High-Load Driving Tests on a Wheel and Suspension Test Bed

Gaseous emissions from brake wear can form secondary particulate matter

Unrecognized volatile and semi-volatile organic compounds from brake wear

A Practical Approach for On-Road Measurements of Brake Wear Particles from a Light-Duty Vehicle

Wear and environmental aspects of composite materials for automotive braking industry

Direct measurement of brake and tire wear particles based on real-world driving conditions

Airborne Brake Wear Emissions from a Battery Electric Vehicle

Investigations of airborne tire and brake wear particles using a novel vehicle design

Brake wear (nano)particle characterization and toxicity on airway epithelial cells in vitro

Assessing the brake particle emissions for sustainable transport: A review

Investigation of Brake Emissions of Different Brake Pad Materials with Regard to Particle Mass (PM) and Particle Number (PN)

A new method to assess vehicle airborne non-exhaust particles: Principle, application and emission evaluation

Contributions of non-tailpipe emissions to near-road PM2.5 and PM10: A chemical mass balance study

Chemical Assessment of Real Driving Tire and Road Wear Particles in Urban and Suburban Seoul, Korea

Dynamometric Investigation on Airborne Particulate Matter from Automobile Brake: Impact of Disc Materials on Brake Emission Factor

Heavy metals from non-exhaust vehicle emissions in urban and motorway road dusts

New insights into reducing airborne particle emissions from brake materials: Grooved textures on brake disc surface

Biological response of an in vitro human 3D lung cell model exposed to brake wear debris varies based on brake pad formulation

Light-Duty Vehicle Brake Emission Factors