Connexin36 distribution in putative CO2-chemosensitive brainstem regions in rat

I. Solomon

DOI: https://doi.org/10.1016/j.resp.2003.09.004

IF: 2.821

2003-12-16

Respiratory Physiology & Neurobiology

Abstract:

What problem does this paper attempt to address?

Color Stability, Physical Properties and Antifungal Effects of ZrO2 Additions to Experimental Maxillofacial Silicones: Comparisons with TiO2

Mazen Alkahtany,Mark W. Beatty,Fahd Alsalleeh,Thomas M. Petro,Bobby Simetich,You Zhou,Dennis Feely,Grigoris Polyzois

DOI: https://doi.org/10.3390/prosthesis5030064

2023-09-08

Prosthesis

Abstract:(1) Background: Color changes, physical degradation, and fungal infections are challenges to the longevity of maxillofacial polydimethylsiloxane (PDMS) elastomers. This study aimed to evaluate color changes, physical properties, and antifungal properties of PDMS loaded with ZrO2 and TiO2 submicron- and nano-sized particles. (2) Methods: A 1% weight of 40 nm or 200 nm diameter ZrO2 or TiO2 nanoparticles was mixed into PDMS with 2% functional intrinsic yellow pigment and polymerized. Control materials contained 13% weight 200 nm silica. Samples were exposed to 3000 h of UVB radiation (200 μW/cm2) or darkness. Color parameters L*a*b* and ∆Eab*, ultimate tensile strength, strain, elastic modulus, and Shore A hardness were measured. Candida albicans growth was measured using XTT and confocal microscopy, and data were analyzed with the Dunnett test (p < 0.01). (3) Results: TiO2 200 nm showed the least color change after 3000 h of UVB radiation, followed by TiO2 40 nm (p < 0.05). The silica-containing control group was superior in all physical property measurements due to higher additive content (p < 0.05). TiO2-containing materials exhibited significantly lower C. albicans growth (p < 0.01) than those loaded with ZrO2 or SiO2. (4) Conclusions: TiO2 nanoparticles of 40 nm and 200 nm, when added to pigmented PDMS at 1% weight, provided the best resistance to color change and significantly lowered C. albicans activity compared to silica- and zirconia-filled elastomers. Particle size differences rendered minor differences for most properties. The incorporation of low-level submicron- and nano-sized TiO2 particles has the potential to improve color stability and antifungal activity in silicones designated for maxillofacial prostheses and may be extended to denture reline applications.
Surface roughness of pigmented and non-pigmented maxillofacial silicone elastomer before and after artificial aging

Mohammed Tahir Abdalqadir,Znar Saeed,Bruska Azhdar

DOI: https://doi.org/10.1088/2053-1591/ad1a60

IF: 2.025

2024-01-05

Materials Research Express

Abstract:Maxillofacial prostheses are frequently composed of silicone elastomers. The rough surface of the silicone material can lead to the accumulation of microorganisms, irritation of the surrounding soft tissue, and progression of some microsites into mechanical failure and color deterioration. This in vitro study aimed to compare the surface roughness of M511 heat-vulcanized maxillofacial silicone before and after artificial aging. Eighty disk-shaped specimens were prepared and divided equally among the five experimental groups based on pigmentation, with 16 samples in each group. Colorless specimens were prepared without adding any pigments. The four study groups were prepared using different pigments (red, blue, yellow, and their mixture). Half of the specimens in each group were tested before aging, whereas the other half were tested after 750 h of artificial aging. The surface roughness was measured using atomic force microscopy (AFM) and the silicone bonds and pigments were observed using Fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR). Data were compared between groups using two-way analysis of variance, independent sample t-test, and Tukey's post hoc test, with p < 0.05 statistically significant. FTIR-ATR showed no differences between the pre- and post-aging groups, with similar peaks. Surface roughness significantly increased in the colorless, blue, and mixed pigment groups (p < 0.001). In contrast, surface roughness significantly decreased in the yellow and red pigment groups (p ≤ 0.001). Therefore, the induced aging considerably impacted the surface topography of the maxillofacial silicone. The pigment type and distribution in the silicone matrix affect the surface roughness. AFM analysis is a simple and straightforward method for assessing the surface roughness at the nanometer level.

materials science, multidisciplinary
Effect of Particle Size of Nano-Oxides on Color Stability and Mechanical Properties of Maxillofacial Silicone Elastomers: An In Vitro Study

Ashika S Mohan,Manju V,Anna Serene Babu,Krishnapriya V N

DOI: https://doi.org/10.11607/ijp.6593

Abstract:Purpose: To evaluate the physical and mechanical properties of maxillofacial silicone elastomers following the incorporation of a specific particle size and concentration of nano-titanium dioxide (TiO2) and nano-zinc oxide (ZnO). Materials and methods: Nano-TiO2 and nano-ZnO of 20-nm and 40-nm particle sizes and in 1% and 2% concentrations were chosen. Silicone elastomer samples were prepared according to the manufacturer's recommendations. The nano-oxides were incorporated via hand spatulation. The samples were subsequently tested for hardness and color stability and were then subjected to aging in an aging chamber for 1,008 hours, following which they were again evaluated for hardness, color stability, and surface roughness. Results: A significant change was noted in the physical and mechanical properties post-aging in all the groups. The samples with nano-TiO2 of 40-nm particle size/2% concentration had the highest hardness, while color stability and surface roughness were higher in samples with nano-TiO2 of 20-nm particle size/1% and 2% concentrations, respectively. Conclusion: It can be concluded that 20-nm nano-TiO2 particles best maintain the ideal properties of maxillofacial silicone elastomers and can potentially be used as alternative opacifiers when mixed with A-2186 maxillofacial silicone elastomers.
Assessment of the color stability of two silicone elastomers for maxillofacial prostheses upon exposure to cold beverages

Anshul Chugh,Mariko Hattori,Marwa A Aboelez,Yuka I Sumita,Noriyuki Wakabayashi,Marwa A. Aboelez,Yuka I. Sumita

DOI: https://doi.org/10.2334/josnusd.23-0360

2024-01-01

Journal of Oral Science

Abstract:PURPOSE: This study investigated the color stability of different commercially available silicone materials for facial prostheses upon exposure to everyday beverages. It was hypothesized that the beverages would not alter the color of the silicone under conditions simulating daily exposure.METHODS: Sixty specimens were fabricated using two materials - VST-50 and Silfy - and exposed to commercially available cold mineral water, tea, or coffee. Specimen color was evaluated on days 1 and 15. The color was measured with a spectrophotometer based on CIELab system and color differences were calculated as ΔE. Statistical analysis was performed using the Kruskal-Wallis test and Mann-Whitney U test.RESULTS: The mean ΔE values after 15 days of exposure to mineral water, cold green tea, and coffee were 1.016, 3.480, and 3.636 for VST-50 and 0.440, 0.798, and 1.425 for Silfy, respectively. Both materials showed significant differences in color, and VST-50 showed a greater color change than Silfy, especially for coffee.CONCLUSION: Pigmented silicone elastomers have low color stability, leading to an overall color change in silicone prostheses when exposed to pigmented beverages. Color changes in such prostheses can be mitigated by selecting materials with better color stability to extend their longevity.

materials science, biomaterials,dentistry, oral surgery & medicine
Titanium Dioxide/Polysiloxane Composites: Preparation, Characterization and Study of Their Color Stability Using Thermochromic Pigments

Evangelia Papachristou,Dimitrios Korres,Diomi Mamma,Dimitris Kekos,Petroula A. Tarantili,Gregory Polyzois

DOI: https://doi.org/10.3390/jcs6070195

2022-07-02

Journal of Composites Science

Abstract:In order to improve thermomechanical, antibacterial and temperature-controlled color-response performance of polydimethylsiloxane (PDMS) in maxillofacial prostheses, the incorporation of titania (TiO2) nanoparticles and thermochromic pigments (TCP) into PDMS was examined. The thermal transitions of TiO2/PDMS nanocomposites, investigated by differential scanning calorimetry (DSC), remain almost unaffected, while an increase of the crystallinity of PDMS was recorded in specimens with higher titania concentrations. The incorporation of titania improves the thermal stability, as it was revealed by thermogravimetric analysis (TGA), as well as the tensile properties of the reinforced elastomer. Nanocomposites with 10 wt% titania presented antibacterial activity against Escherichia Coli, leading to 72% reduction of the bacterial colony after 3 h of exposure. Specimens colored with red TCP (0.2 and 0.6 wt%) showed significant color change at a lower temperature (−20 °C) in comparison with that at an ambient temperature, especially at lower TCP concentration (0.2 wt%). Accelerating aging experiments, consisting of repeated cycles of combined exposure to UV-radiation and damp heating, of PDMS colored with TCP showed poor color stability of the specimens, from the first hours of exposure. The addition of titania to polysiloxane specimens works as an opacifier providing a positive effect on the color stability of the examined thermochromic pigment.
Effect of nanoparticles on color stability and mechanical and biological properties of maxillofacial silicone elastomer: A systematic review

Nithin Kumar Sonnahalli,Ramesh Chowdhary

DOI: https://doi.org/10.4103/jips.jips_429_19

Abstract:Aim: The aim of this systematic review was to evaluate the effect of addition of various nanoparticles into maxillofacial silicone elastomer on color stability and mechanical and biological properties of the silicone elastomer. Settings and design: This systematic review was conducted in accordance with the Preferred Reporting Items for Systematic Reviews and Meta-Analyses guidelines(PRISMA). Materials and methods: The electronic database search in MEDLINE/PubMed was based on population (silicone elastomer), intervention (nanoparticles), comparison (unreinforced silicone elastomer with nanoparticle-reinforced silicone elastomer), outcome (color stability and mechanical, physical, and biological properties), i.e., PICO framework. The key words used are ("maxillofacial silicone" OR "silicone elastomer" OR "facial silicone") AND ("nanoparticles" OR "Nano-oxides") AND ("colour stability" OR "Hardness," "tensile strength" OR "tear strength" OR "antifungal activity"). Results: The database search resulted in 2099 studies, of which 2066 articles were excluded as they were irrelevant, duplicates, and data were not available. The remaining 33 full-text articles were assessed for eligibility, out of which 2 articles were in Chinese language, 3 articles were thesis documents, and 8 were review articles. A total of 12 articles were excluded and the remaining 20 articles were included. One article was yielded by hand search of references of included studies. A total of 21 studies were included in the present systematic review. Conclusion: With the available evidence in the literature, it can be concluded that addition of nanoparticles at various concentrations may improve the physical and mechanical properties and color stability of the prosthesis made from the silicone elastomers.
Biocompatibility profile of aged pigmented and non‐pigmented silicone elastomer for combined maxillofacial defects

Eman M. Saleh,Faten S. Mohamed,Radwa A. Mehanna,Marwa M. Essawy,Ingy S. Soliman

DOI: https://doi.org/10.1111/jopr.13873

2024-05-26

Journal of Prosthodontics

Abstract:Purpose To assess the biocompatibility of platinum silicone elastomer A‐2000 used in combined maxillofacial defects prosthesis, after being deteriorated by an accelerated aging process resembling both the extra and intraoral environment. This assessment was done indirectly on human‐derived dermal and gingival tissues. Materials and Methods One hundred eight samples of room‐temperature vulcanized A‐2000 platinum silicone were equally divided into extrinsically pigmented and non‐pigmented groups to replicate combined maxillofacial defects. Accelerated aging was applied to pigmented samples to mimic extra‐ and intra‐oral conditions, while non‐aged counterparts served as controls. After isolating human cell lineages, dermal and gingival fibroblasts were indirectly exposed to silicone sample media. Cytotoxicity to cultured fibroblasts was assessed via MTT assay. Statistical significance was determined by repeated measures of one‐way ANOVA (p < 0.01), evaluating cytotoxicity on dermal and gingival fibroblasts. Results MTT assay showed increased cytotoxicity in pigmented silicon samples subjected to extraoral aging compared to non‐aged counterparts (p < 0.01). Non‐pigmented silicon, modeling intraoral conditions, exhibited cytotoxicity after 48 h (p < 0.05). Both aged and non‐aged silicon extracts equally sensitized gingival fibroblasts at 72 h (p 0.05, except at 24 h, r = 0.2), with accelerated aging showing minimal impact on the pigmentation effect (p > 0.05). Conclusion The retrieved diminished cellular metabolic activity of platinum silicone elastomer was in an acceptable clinical range, pointing out the importance of periodic assessments of the maxillofacial prosthesis for replacement depending on aging and cytotoxic harmful cellular responses.

dentistry, oral surgery & medicine
Serum and urinary beta-hexosaminidase as markers of heavy drinking.

P. Kärkkäinen

Alcohol and Alcoholism

Abstract:Serum and urinary beta-hexosaminidase (SHEX and UHEX) were determined in 32 alcoholic men admitted to inpatient detoxification treatment for seven days, and in 27 teetotallers. On the admission SHEX was increased in 68.8% and UHEX in 81.3% and after seven days of abstinence the corresponding percentages were 37.5 (SHEX) and 71.9 (UHEX). During the treatment SHEX decreased significantly while UHEX did not. On the admission to the treatment UHEX correlated positively with SHEX (r = 0.54; P less than 0.01). The results suggest that UHEX may be a more sensitive marker of heavy drinking than SHEX. Furthermore UHEX stays longer elevated than SHEX.
Color stability of precolored and extrinsically colored monolithic multilayered polychromatic zirconia: Effects of surface finishing and aging

Feras M. Abounassif,Amal Alfaraj,Thuraya Gadah,Chao‐Chieh Yang,Tien‐Min G. Chu,Wei‐Shao Lin

DOI: https://doi.org/10.1111/jopr.13875

2024-06-25

Journal of Prosthodontics

Abstract:Purpose To explore the impact of zirconia types, coloring methods, and surface finishing on the color stability of monolithic multilayered polychromatic zirconia after artificial aging, including thermocycling and simulated toothbrushing. Materials and Methods Eighty square‐shaped zirconia samples were divided into 2 types (M3Y‐TZP and M6Y‐PSZ), further categorized based on coloring methods (precolored and extrinsically colored) and surface finishing techniques (mechanical polishing or glazing). The color stability was assessed using the CIEDE2000 formula. Artificial aging was simulated via thermocycling and toothbrushing. All samples were analyzed with a spectrophotometer to determine the post‐aging color changes (ΔE00). The ΔE00 were interpreted and classified using the 50:50% perceptibility threshold (PT) and the 50:50% acceptability threshold (AT). Comparisons between groups for ΔE00 differences were performed using three‐way ANOVA, with pairwise comparisons facilitated by Fisher's protected least significant difference test, α = 0.05. Results The study results indicated significant impacts of zirconia type, coloring method, and surface finishing on color stability. The M6Y groups experienced significantly greater color changes (6.61 ± 1.63) compared to the M3Y groups (3.40 ± 2.24), p < 0.0001. For both types of zirconia, extrinsically colored samples exhibited significantly higher ΔE00 when mechanically polished (p = 0.004). However, surface finishing had no significant effect on ΔE00 in precolored samples of either zirconia material (p = 1.000). The evaluation and categorization of ΔE00 variations indicated that nearly all color changes in the M6Y groups, regardless of being precolored, extrinsically colored, polished, or glazed, were deemed extremely unacceptable (Grade 1). In contrast, the M3Y groups showed more acceptable results, with the majority of color changes classified as moderately unacceptable (Grade 3). Conclusions The color stability of multilayered polychromatic zirconia is influenced by the type of material, extrinsic coloring, and the chosen surface treatment post‐artificial aging. The translucent 6Y‐PSZ exhibited lower color stability, especially with only mechanical polishing. For the fabrication of M3Y‐TZP and 6Y‐PSZ monolithic multilayered polychromatic zirconia restorations, extrinsic coloring should be paired with glazing to maintain color stability. Conversely, in the absence of extrinsic coloring, both glazing and mechanical polishing are effective in preserving color stability.

dentistry, oral surgery & medicine
Impact of Nanoparticle Addition on the Surface and Color Properties of Three-Dimensional (3D) Printed Polymer-Based Provisional Restorations

Maram A. AlGhamdi,Fatimah M. Alatiyyah,Rawan F. Almedarham,Zainab H. Al Dawood,Farah Y. Alshaikhnasser,Shaymaa Y. Alboryh,Soban Q. Khan,Reem Abualsaud,Mohammed M. Gad

DOI: https://doi.org/10.3390/nano14080665

IF: 5.3

2024-04-11

Nanomaterials

Abstract:This study aimed to evaluate and compare the impact of additives such as ZrO2 and SiO2 nanoparticles (ZrO2NP or SiO2NP) on the hardness, surface roughness, and color stability of 3D printed provisional restorations. Two hundred samples in total were printed using 3D printed resins (ASIGA, and NextDent). Each resin was modified with ZrO2NPs or SiO2NPs in two different concentrations (0.5 wt% and 1 wt%), while one group was kept unmodified (n = 10). Disc-shaped (15 × 2.5 mm) samples were designed and printed in accordance with the manufacturer’s recommendation. Printed discs were evaluated for color changes through parameters CIELAB 2000 system (ΔE00), hardness using Vickers hardness test, and surface roughness (Ra) using a noncontact profilometer. After calculating the means and standard deviations, a three-way ANOVA and Tukey post hoc test were performed at α = 0.05. The addition of ZrO2NPs or SiO2NPs to ASIGA and NextDent resins significantly increased the hardness at a given level of concentration (0.5% or 1%) in comparison with pure (p 0.05). The highest hardness value was detected in 1% ZrO2NPs with 29.67 ± 2.3. The addition of ZrO2NPs or SiO2NPs had no effect on the Ra (p > 0.05), with 1% ZrO2NPs showing the highest value 0.36 ± 0.04 μm with NextDent resin. ZrO2NPs induced higher color changes (∆E00), ranging from 4.1 to 5.8, while SiO2NPs showed lower values, ranging from 1.01 to 1.85, and the highest mean ∆E00 was observed in the 1% ZrO2NPs group and NextDent resin. The incorporation of ZrO2NPs and SiO2NPs in 3D printed provisional resins increased the hardness without affecting the surface roughness. The optical parameters were significantly affected by ZrO2NPs and less adversely affected by SiO2NPs. Consequently, care must be taken to choose a concentration that will improve the materials’ mechanical performance without detracting from their esthetic value.

materials science, multidisciplinary,nanoscience & nanotechnology,physics, applied,chemistry
Evaluation of the color stability of three maxillofacial silicone materials after exposure to beverages: An in vitro study

Anshul Chugh,Mariko Hattori,Cheewin Towithelertkul,Yuka I Sumita,Noriyuki Wakabayashi

DOI: https://doi.org/10.1016/j.heliyon.2024.e25529

IF: 3.776

2024-01-30

Heliyon

Abstract:Purpose: Oral cancer often requires treatments like surgical intervention, involving surgical resection of lips and other facial parts. For those patients, prosthetic rehabilitation following surgery promotes social reintegration. This study explores the color stability of various commercially available silicone materials for facial prostheses when exposed to everyday beverages like coffee and tea. The hypothesis is that these beverages can induce color changes in silicones, simulating conditions of daily use. Material and methods: A total of 90 specimens were fabricated. There were 30 specimens deefor each of 3 nonpigmented silicone elastomers: Silfy, A-2186-F and VST-50 and were immersed in tea or coffee at drinking temperature and evaluated for color changes at time points of 0 h, 1 h, and 6 h. The color was measured with a colorimeter that used the CIE L*a*b* system and the color change ΔΕ was calculated to quantify the color change. Statistical analysis was performed by using the Kruskal-Wallis test, the Mann-Whitney U test, and the Wilcoxon signed-rank Test. The threshold for statistical significance was P < .05. Results: Color change was observed for each of the silicones exposed to the beverages (P < .05). The value of ΔE was significantly higher for A-2186-F compared with VST-50 and Silfy (P < .05 in all beverages at 6 h). The color of the elastomers progressively changed while immersed in the beverages over 6 h. The change in color was significantly greater for coffee compared with tea (P < .05). Conclusions: The color stability of nonpigmented silicone elastomers is inherently low, which contributes to the overall color change of silicone prostheses when they are exposed to beverages that contain pigments. The elastomer A-2186-F had greatest values of ΔE among the materials tested. Color changes of silicone prostheses can be lessened by selecting materials with consideration of color stability to improve their longevity and extend their period of use.
Coloring Multilayer Zirconia May Affect Its Optical and Mechanical Properties

S.M. Čokić,M. Li,S. Huang,J. Vleugels,B. Van Meerbeek,F. Zhang

DOI: https://doi.org/10.1177/00220345241271211

2024-10-06

Journal of Dental Research

Abstract:Journal of Dental Research, Ahead of Print. The coloring process of monolithic dental zirconia caused considerable debate on the possible effects of different coloring methods. The main objective of this study was to investigate the influence of pigments in 3 multilayer 5-mol% yttria partially stabilized zirconia (5Y-PSZ) disks (Lava Esthetic A2 [Zr-AGG_A2] and Bleach [Zr-AGG_BL], both 3M Oral Care, and Katana STML A2 [Zr-NoAGG], Kuraray Noritake). The influence of pigment addition on the translucency parameter (TP00), fracture toughness, Vickers hardness, biaxial strength, and hydrothermal stability was assessed and correlated with the microstructure and phase composition. The pigment composition and distribution were evaluated by light and fluorescence microscopy, electron probe microanalysis, and nano–scanning electron microscopy. The chemical and phase composition and aging behavior were assessed using X-ray fluorescence and X-ray diffraction, respectively, while the aging sensitivity of the pigments was evaluated using micro-Raman spectroscopy. In contrast to Zr-NoAGG, possessing a typical 5Y-PSZ microstructure, the pigment additions in both Zr-AGG_A2/BL zirconia resulted in large yellow and blue fluorescent Er-, Hf-, and Al-containing agglomerates composed of small grains (0.57 μm and 0.38 μm, respectively, vs. 0.92 μm for the surrounding grains) with lower Y2O3 content. Zr-AGG_A2 had the lowest aging resistance, with transformation degradation occurring exclusively within the pigment agglomerates. All zirconia grades had a high Y2O3 content (4.2%–5.7 mol%) tetragonal ZrO2 phase and a high (42%–55 wt%) cubic ZrO2 phase content. Although no statistical differences were measured for hardness and toughness, Zr-NoAGG had a significantly higher TP00, higher flexural strength, and lower mechanical reliability compared to both Zr-AGG_A2/BL zirconia. The rare-earth oxide-containing zirconia agglomerates that were added as pigments to the multilayered monolithic Zr-AGG_A2/BL zirconia are the cause for their lower optical and mechanical properties and reduced aging resistance.

dentistry, oral surgery & medicine
In Vitro Assessment of Artificial Aging on the Antifungal Activity of PMMA Denture Base Material Modified with ZrO2 Nanoparticles

Shorouq Khalid Hamid,Lujain Ali Alghamdi,Faris A. Alshahrani,Soban Q. Khan,Asif Matin,Mohammed M. Gad

DOI: https://doi.org/10.1155/2021/5560443

2021-05-13

International Journal of Dentistry

Abstract:The antifungal effect of zirconium dioxide nanoparticles (ZrO2NPs) incorporated into denture base material has been inadequately investigated; additionally, to the authors’ knowledge, no studies have assessed the influence of artificial aging on the antifungal activity of these particles. Methodology. Heat-polymerized acrylic resin disks were fabricated and divided into four groups (0%, 1%, 2.5%, and 5% ZrO2NPs by weight). Antifungal activity was assessed using the direct culture and disk diffusion methods. Surface roughness and contact angles were measured using a profilometer and a goniometer, respectively. The artificial aging procedure was performed by repeating all tests at 7, 14, and 30 days following 2 rounds of thermocycling. Data were analyzed using ANOVA and Tukey’s post-hoc test ( p < 0.05 ). Results. The addition of ZrO2NPs significantly decreased the adhesion of Candida albicans with and without artificial aging procedures ( p < 0.001 ), while the disk diffusion methods did not reveal inhibition zones. ZrO2NP-modified specimens displayed significantly higher surface roughness compared to specimens in the control group ( p < 0.05 ) and showed the same behaviors with artificial aging procedures. The contact angle was significantly decreased in all modified groups in comparison to the control group ( p < 0.05 ). Conclusion. The addition of ZrO2NPs to polymethylmethacrylate denture base material reduced the adhesion of Candida albicans with a long-term antifungal effect. With the addition of ZrO2NPs, contact angles were decreased and surface roughness was increased; 1% was the most appropriate concentration. Clinical significance. The addition of ZrO2NPs to denture base material confers a long-term antifungal effect and could be used as a possible method for preventing and treating denture stomatitis.
Color Modifications of a Maxillofacial Silicone Elastomer under the Effect of Cigarette Smoke

Anca Irina Gradinariu,Alexandru-Constantin Stoica,Alexandra Bargan,Carmen Racles,Carmen Gabriela Stelea,Victor Vlad Costan

DOI: https://doi.org/10.3390/ma17164089

IF: 3.4

2024-08-19

Materials

Abstract:Although it is known (from the observations of medical professionals) that cigarette smoke negatively affects maxillofacial prostheses, especially through staining/discoloration, systematic research in this regard is limited. Herein, the color modifications of M511 maxillofacial silicone, unpigmented and pigmented with red or skin tone pigments, covered with mattifiers, or with makeup and mattifiers, and directly exposed to cigarette smoke, were investigated by spectrophotometric measurements in the CIELab and RGB color systems. The changes in color parameters are comparatively discussed, showing that the base silicone material without pigmentation and coating undergoes the most significant modifications. Visible and clinically unacceptable changes occurred after direct exposure to only 20 cigarettes. By coating and application of makeup, the material is more resistant to color changes, which suggests that surface treatments provide increased protection to adsorption of the smoke components. The dynamic water vapor sorption (DVS) measurements indicate a decrease of the sorption capacity in pigmented versus unpigmented elastomers, in line with the changes in color parameters.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
The changing pathogenesis of aspergilloma or "fungus ball".

E. Bardana

DOI: https://doi.org/10.1016/S0022-5347(17)49176-2

1984-09-01

Abstract:
Effects of Aging on the Mechanical Properties of Dental Pigmented 3Y-Tzp Ceramics

Yuanfu Yi,Ning Wen,Den Bin,Longquan Shao,Chen Wang,Jiemo Tian

DOI: https://doi.org/10.4028/www.scientific.net/amr.177.136

2010-01-01

Advanced Materials Research

Abstract:The purpose of this study was to investigate the structure, mechanical and low temperature aging properties of colored dental zirconia ceramics. Colored 3Y-TZP zirconia dental zirconia ceramics were made by mixing colorants and their combinations into a 3Y-TZP powder, the green body were compacted at 200MPa, presinter at 1050°C and densely sintered at 1500°C for 2h. Specimens were subjected to an accelerated aging test carried out in an autoclave in steam at 134°C, 2bar, for 4hs. XRD was used to identify the crystal phases, three-point bending strength were tested before and after aging according to the ISO 6872 standard, polished and aging specimens were observed by Atomic Force Microscopy (AFM) to evaluate surface microstructure. Tetragonal-to-monoclinic phase transformation was detected for both uncolored and colored specimens, the relative content of monoclinic phase was increased with the prolonged aging time. Aging had no significant negative effects on flexural strength on colored 3Y-TZP. The nucleation and growth of monoclinic phase were detected by AFM in surface of both colored and uncolored zirconia.
Evaluating the effect of barium titanate nanofiller addition on the thermal conductivity and physio-mechanical properties of maxillofacial silicone

Yasir M Kareem,Thekra I Hamad,Matheel AL-Rawas

DOI: https://doi.org/10.26477/jbcd.v36i2.3674

2024-06-15

Journal of Baghdad College of Dentistry

Abstract:Background: Silicone elastomers have been extensively used as the most acceptable material in the manufacturing of maxillofacial and other kinds of prosthetic devices. The durability of maxillofacial prostheses depends on the material chosen, the patient's attitude and feelings regarding the prosthesis, and how they perform for specific needs. Aims: This study aimed to investigate the influence of adding barium titanate (BaTiO3) nanoparticles on the mechanical and physical characteristics of room-temperature-vulcanized (RTV) VerSilTal (VST-50) maxillofacial silicone elastomer, including thermal conductivity, tear strength, and water absorption and solubility. Materials and methods: 0.5 wt% and 0.75 wt% BaTiO3 nanoparticles were added to RTV VST-50 platinum silicone elastomer. Ninety specimens were prepared and divided into three main groups: one control group and two experimental groups (0.5 and 0.75 wt%). The collected data were statistically analyzed by one-way ANOVA and Tukey (HSD) test (significant level at P ≤ 0.05). The homogeneity and normal distribution of data were assessed by Levene's and Shapiro Wilk's tests, respectively. Result: Both experimental groups showed a remarkable increase in tear strength, thermal conductivity, and water absorption compared with the nonadditive control group. For solubility, the group of 0.5 wt% additive showed an insignificant increase, whereas the group of 0.75 wt% showed a significant increase compared with the control group. Conclusion: The addition of BaTiO3 nanoparticles to RTV VST-50 enhanced the thermal conductivity and tear strength. Water absorption and solubility were also increased, but the values were clinically insignificant. FTIR revealed no chemical interaction between BaTiO3 and silicone. FE-SEM showed the uniform scattering of BaTiO3 inside the silicone matrix.
Effect of Bisoctrizole on Ultraviolet (UV) Absorption Properties of Silicone and Effect on Surface Roughness - An In Vitro Study

Widyan Abbas Ahmed,Bayan Saleem Khalaf

DOI: https://doi.org/10.4103/ijdr.ijdr_703_23

2024-04-01

Abstract:Background: Premature degradation is the problem of maxillofacial silicones, significantly affected by ultraviolet exposure, contributing to silicones photodegradation. Degradation necessitates frequent replacement of prostheses that increase the total cost of rehabilitation. Aims: This study evaluated the effect of bisoctrizole on the ultraviolet absorption properties of silicone material and the stability of this absorption over time. Also, the bisoctrizole effect on the surface roughness of silicone was evaluated. Methods: There were 60 prepared specimens of room temperature-vulcanising maxillofacial silicone equally divided into two groups according to the conducted tests: ultraviolet absorption test and the surface roughness test. Each group was further subdivided into groups of 10 specimens based on the weight concentration of the ultraviolet (UV) absorber added: 0%, 1% and 2%. The UV absorbance of coloured specimens was measured before and after artificial weathering for 100 and 200 hours. Repeated-measures analysis of variance (ANOVA) was applied for UV absorption results, and one-way ANOVA was applied for the roughness test results to test the changing significances. Result: Bisoctrizole incorporation led to a highly significant improvement in ultraviolet absorption in all groups, maintaining a high level even after subjecting the specimens to artificial weathering. Furthermore, the addition resulted in a significant increase in surface roughness as the concentration of bisoctrizole increased. Conclusion: Despite the surface roughness changes, bisoctrizole demonstrated efficacy as a UV absorber for maxillofacial silicone, making it valuable for applications such as maxillofacial prosthetics that require UV protection.
In Vitro Evaluation of Color and Surface Roughness Changes of Polyetheretherketone, Monolithic Zirconia, and Resin Nanoceramics Exposed to Staining Liquids

E H Demir Sevinç,C B Inal,C Aydin

DOI: https://doi.org/10.4103/njcp.njcp_259_24

2024-07-01

Abstract:Background: This study aims to investigate color stability and surface roughness of polyetheretherketone (PEEK), zirconia, and hybrid ceramics while stored in different liquids. Methods: A total of 240 specimens were prepared from monolithic zirconia, PEEK, and hybrid ceramics. All specimens were polished using rubber sets with different grain sizes. Color parameters (L*, a*, b*) were measured three times using a dental spectrophotometer in standard D65 lightning. Each group was divided into eight different groups to be kept in eight different solutions as distilled water, cola, red wine, tea, coffee, heptane, citric acid, and 50% ethanol. Specimens were held in solutions at 37°C for 12 days. Color measurements were repeated, and color change (ΔE) was calculated using the CIE Lab formula. Results: The color difference of PEEK specimens was found above the clinically acceptable limit; however, color differences for monolithic zirconia produced by coffee were found within the clinically acceptable limits. ZR and HC specimens' color change values were found between threshold values (1<ΔE < 3.3). The differences observed in surface roughness levels amongst the ZR specimens could be caused by the polishing instrument and procedure. Conclusion: The color change of the materials was within acceptable limits, whereas the surface roughness increased more than 0.2 µm. Especially cola, heptane, and red wine significantly increased the mean surface roughness.
The Effect of Chemical Disinfectants on Maxillofacial Silicone With the Addition of Silver Nanoparticles: An Original Research

Vedant Pathak,Seema R Kambala,Tanvi Jaiswal,Anjali Bhoyar,Mithilesh Dhamande

DOI: https://doi.org/10.7759/cureus.66484

2024-08-08

Cureus

Abstract:Background and objective Silicone has emerged as the most widely accepted material for facial prosthesis fabrication. However, silicone materials have certain limitations. Several techniques have been investigated to lessen the degradation of the polymer, such as the use of nanoparticles and nano-oxides, etc. In this study, we aimed to evaluate the effect of various chemical disinfectants on color stability, hardness, and surface roughness of maxillofacial silicone, after the addition of silver nanoparticles. Materials and methods This was an in vitro study carried out in the Department of Prosthodontics, Sharad Pawar Dental College and Hospital; 80 samples of maxillofacial silicone incorporated with silver nanoparticles (in a concentration of 20 ppm) were fabricated in a mold of 3 x 10 mm dimension disc. The samples were then tested for surface roughness (using a digital roughness tester), Shore A hardness (using a durometer), and color stability (using a spectrophotometer). The samples were then classified into four groups according to various disinfectants used: sodium hypochlorite (1% w/w), chlorhexidine gluconate (0.2%), and neutral soap, and distal water was deemed the control group. After 48 hours, the samples underwent retesting to assess for changes in readings under the same parameters (i.e., surface roughness, Shore A hardness, and color stability) to obtain results, i.e., the samples were tested after fabrication, before immersion, and 48 hours after immersion in disinfectants. Results When taking into account the surface roughness, the maximum roughness value was observed in the sodium hypochlorite group and the least roughness value in distilled water (mean % change of 38.359 to negligible change in the distilled water group). As for the Shore A hardness, the maximum hardness value was seen in the sodium hypochlorite group and the least hardness value in distilled water (mean % change of 15.780 to 2.125 in distilled water). Regarding color stability, the maximum increase in color values was seen in the sodium hypochlorite group (mean: 2.4) followed by the neutral soap group (mean: 1.653); the chlorhexidine gluconate group (mean: -0.287) showed the maximum decrease in color value from the initial to the final phase. Conclusions Based on our findings, surface roughness altered the most when samples were immersed in 1% sodium hypochlorite disinfectant and the least when samples were immersed in neutral soap disinfectant. Shore A hardness altered the most when samples were immersed in 1% sodium hypochlorite disinfectant, but altered the least when samples were immersed in neutral soap disinfectant. Color stability altered the most when samples were immersed in neutral soap disinfectant, but altered the least when samples were immersed in 0.2% chlorhexidine gluconate. Disinfection with neutral soap seems to lead to fewer changes in physical properties (i.e., surface roughness and Shore A hardness) and hence is recommended as a disinfectant for silicone prosthesis. However, our study also showed that 0.2% chlorhexidine gluconate had the least effect on the parameter of color stability, and hence it could be the disinfectant of choice for prostheses with high esthetic requirements.

Connexin36 distribution in putative CO2-chemosensitive brainstem regions in rat

Color Stability, Physical Properties and Antifungal Effects of ZrO2 Additions to Experimental Maxillofacial Silicones: Comparisons with TiO2

Surface roughness of pigmented and non-pigmented maxillofacial silicone elastomer before and after artificial aging

Effect of Particle Size of Nano-Oxides on Color Stability and Mechanical Properties of Maxillofacial Silicone Elastomers: An In Vitro Study

Assessment of the color stability of two silicone elastomers for maxillofacial prostheses upon exposure to cold beverages

Titanium Dioxide/Polysiloxane Composites: Preparation, Characterization and Study of Their Color Stability Using Thermochromic Pigments

Effect of nanoparticles on color stability and mechanical and biological properties of maxillofacial silicone elastomer: A systematic review

Biocompatibility profile of aged pigmented and non‐pigmented silicone elastomer for combined maxillofacial defects

Serum and urinary beta-hexosaminidase as markers of heavy drinking.

Color stability of precolored and extrinsically colored monolithic multilayered polychromatic zirconia: Effects of surface finishing and aging

Impact of Nanoparticle Addition on the Surface and Color Properties of Three-Dimensional (3D) Printed Polymer-Based Provisional Restorations

Evaluation of the color stability of three maxillofacial silicone materials after exposure to beverages: An in vitro study

Coloring Multilayer Zirconia May Affect Its Optical and Mechanical Properties

In Vitro Assessment of Artificial Aging on the Antifungal Activity of PMMA Denture Base Material Modified with ZrO2 Nanoparticles

Color Modifications of a Maxillofacial Silicone Elastomer under the Effect of Cigarette Smoke

The changing pathogenesis of aspergilloma or "fungus ball".

Effects of Aging on the Mechanical Properties of Dental Pigmented 3Y-Tzp Ceramics

Evaluating the effect of barium titanate nanofiller addition on the thermal conductivity and physio-mechanical properties of maxillofacial silicone

Effect of Bisoctrizole on Ultraviolet (UV) Absorption Properties of Silicone and Effect on Surface Roughness - An In Vitro Study

In Vitro Evaluation of Color and Surface Roughness Changes of Polyetheretherketone, Monolithic Zirconia, and Resin Nanoceramics Exposed to Staining Liquids

The Effect of Chemical Disinfectants on Maxillofacial Silicone With the Addition of Silver Nanoparticles: An Original Research