Abstract:To investigate the effect of heat loss reduction due to thermal insulator and thermal interface resistance due to multi-layer structure in order to improve the efficiency of a thermoelectric device, a thermoelectric concrete brick was fabricated using a unileg n-type CaMnO 3 thermoelectric module inside. CaMnO 3 thermoelectric materials were synthesized by starting materials CaCO 3 and MnO 2 to produce a unileg n-type CaMnO 3 module. Thermoelectric concrete brick consisted of two types: I-layer brick (one layer of concrete thermal insulator) and III-layer brick (three layers of different concrete insulators). The occurring temperature difference, electric current and voltage on the CaMnO 3 module and thermoelectric concrete brick were measured in closed and open circuits. The temperature difference, thermal distribution, and output voltage when applying constant temperatures of 100, 200 and 400 °C were measured. Computer simulations of the Finite Element Method (FEM) were performed to compare with the experimental results. The trends of the temperature difference and the output voltage from the experimental and computer simulations were in good agreement. The results of the temperature difference during the hotter side temperature of 200 °C exhibited the temperature difference along the vertical direction of the thermoelectric concrete bricks for both types of the III-layer brick of 172 °C and the I-layer brick of 132 °C are larger than that of the CaMnO 3 TEG module without using a thermal concrete insulator of 108 °C. The thermoelectric concrete bricks of the III-layer brick type of 27.70 mV displayed output voltage results being higher than those of the I-layer brick of 26.57 mV and the CaMnO 3 TEG module without using a thermal concrete insulator of 24.35 mV. Thermoelectric concrete brick of the III-layer brick type displayed higher electric generation power than the I-layer brick and the CaMnO 3 TEG module. Additionally, the results exhibited the capability of thermoelectric concrete brick in the III-layer brick model for electric generation power based on the temperature difference. The TEG concrete brick of I-layer concrete covering the series–parallel combination circuit of 120 modules of the unileg n-type CaMnO 3 was constructed and then embedded on the outer surface of the furnace. During the maximum hotter side temperature of 580 °C of the concrete brick, the temperature difference between the hotter side and the cooler side of the brick occurred at 365 °C and the maximum output voltage was obtained at 581.7 mV.

A large-sized thermoelectric module composed of cement-based composite blocks for pavement energy harvesting and surface temperature reducing

Recent advances in thermoelectric technology to harvest energy from the pavement

Enhanced thermoelectric performance of low carbon cement-based composites by reduced graphene oxide

Enhancing thermal conductivity of cement-based composites by optimizing pores and adding pitch-based carbon fibers for pavement cooling

Significant Improvement in Thermoelectric Properties of Carbon-Reinforced Cementitious Composites Achieved by Regulating the Graphitization Degree of Expanded Graphite

Synergistic optimization of thermoelectric performance in cementitious composites by lithium carbonate and carbon nanotubes

Fabrication and thermoelectric conversion of thermoelectric concrete brick with buried unileg N-type CaMnO3 thermoelectric module inside

Solar energy harvesting pavements on the road: comparative study and performance assessment

Enhancing the thermoelectric characteristics of thermoelectric cement matrix composites by (Ca0.87Ag0.1La0.03)3Co4O9 binary metal oxide

Performance analysis of thermally and non-conductive cement mortar prepared from waste iron scraps and magnetite sand

Boosting power factor of thermoelectric cementitious composites by a unique CNT pretreatment process with low carbon content

Numerical simulation of a novel pavement integrated photovoltaic thermal (PIPVT) module

Design and performance of a modular 1 kilowatt-level thermoelectric generator for geothermal application at medium-low temperature

Development of two-dimensional nano Mts/SA phase change materials for self-adjusting temperature of pavement

Mixed “Ionic-Electronic” Thermoelectric Effect of Reduced Graphene Oxide Reinforced Cement-Based Composites

Building the cooling roads with high thermal conductivity pavements to relieve urban heat island effect

Experimental Study to Analyze Feasibility of a Novel Panelized Ground-Source Thermoelectric System for Building Space Heating and Cooling

Ionic Thermoelectric Effect and Mechanism of Cement-Based Materials

Study of self-synthesised phase change composite materials (PCCM) in porous cement concrete (PCC) for sustainable urban pavement

Electrical Resistivity and Joule Heating Characteristics of Cementitious Composites Incorporating Multi-Walled Carbon Nanotubes and Carbon Fibers

Thermoelectric properties of cement composite analogues from first principles calculations