Abstract:As a potential candidate for the next generation of high-temperature alloys, refractory high entropy alloys (RHEAs) have excellent mechanical properties and thermal stability, especially for high-temperature applications, where the processing of RHEAs plays a critical role in engineering applications. In this work, the wire electrical discharge machining (WEDM) performance of WNbMoTaZrx (x = 0.5, 1) RHEAs was investigated, as compared with tungsten, cemented carbide and industrial pure Zr. The cutting efficiency (CE) of the five materials was significantly dependent on the melting points, while the surface roughness (Ra) was not. For the RHEAs, the CE was significantly affected by the pulse-on time (ON), pulse-off time (OFF) and peak current (IP), while the surface roughness was mainly dependent on the ON and IP. The statistical analyses have shown that the CE data of RHEAs have relatively-smaller Weibull moduli than those for the Ra data, which suggests that the CE of RHEAs can be tuned by optimizing the processing parameters. However, it is challenging to tune the surface roughness of RHEAs by tailoring the processing parameters. Differing from the comparative materials, the WEDMed surfaces of the RHEAs showed dense spherical re-solidified particles at upper recast layers, resulting in larger Ra values. The proportion of the upper recast layers can be estimated by the specific discharge energy (SDE). Following the WEDM, the RHEAs maintained the main BCC1 phase, enriched with the W and Ta elements, while the second BCC2 phase in the Zr1.0 RHEA disappeared. Strategies for achieving a better WEDMed surface quality of RHEAs were also proposed and discussed.

Microstructure and Mechanical Properties of Novel High-Strength, Low-Activation Wx(TaVZr)100-x (x = 5, 10, 15, 20, 25) Refractory High Entropy Alloys

Microstructure and Mechanical Properties of High-Specific-Strength (TiVCrZr)100−xWx (x = 5, 10, 15 and 20) Refractory High-Entropy Alloys

Microstructures and mechanical properties of TiZrHfNbTaWx refractory high entropy alloys

Microstructures and mechanical properties of Ta–Nb–Zr–Ti–Al refractory high entropy alloys with varying Ta/Ti ratios

The Microstructures, Mechanical Properties, and Deformation Mechanism of B2-Hardened NbTiAlZr-Based Refractory High-Entropy Alloys

Microstructures and mechanical properties of novel MoTaVW refractory high-entropy alloys

Excellent room-temperature tensile ductility in as-cast Ti37V15Nb22Hf23W3 refractory high entropy alloys

Experimental and DFT Investigations of AlNbTiVZr High Entropy Alloys with Excellent Mechanical Properties

Microstructure and mechanical performances of novel multi-phase refractory high entropy alloys in Ti-Zr-V-Mo fabricated by vacuum arc melting

On the WEDM of WNbMoTaZr x (x = 0.5, 1) Refractory High Entropy Alloys

A single-phase Ti3Zr1.5NbVAl0.25 refractory high entropy alloy with excellent combination of strength and toughness

Microstructure Modification and Ductility Improvement for TaMoNbZrTiAl Refractory High Entropy Alloys via Increasing Ti Content

Microstructure and Mechanical Properties of TaNbVTiAlx Refractory High-Entropy Alloys

A single-phase V0.5Nb0.5ZrTi refractory high-entropy alloy with outstanding tensile properties

Effect of Zr on the as-cast microstructure and mechanical properties of lightweight Ti2VNbMoZrx refractory high-entropy alloys

Microstructures and Mechanical Properties of TixNbMoTaW Refractory High Entropy Alloys

Mechanical properties and oxidation behavior of NbMoTaW x refractory high entropy alloys

Composition control and heat treatment effect on characteristics of ZrNbTaHf x refractory high entropy alloys

Enhanced ductility in hot compression tests by tailoring microstructure in the refractory high-entropy alloys MoNbTaTiV Zr

Ductile Ti1.5ZrNbAl0.3 refractory high entropy alloy with high specific strength

Intrinsic factors responsible for brittle versus ductile nature of refractory high-entropy alloys