Abstract:The evolution of phase composition and mechanical properties and the formation of oxide layers on Fe40–xNiCoCrAlx (x = 5 and 10 at.%) alloys in long-term oxidation at 900 and 1000°C were studied. In the initial cast state, depending on the aluminum content and valence electron concentration, the alloys contain only an fcc solid solution (VEC = 8 e/a) or a mixture of fcc and bcc phases (VEC = = 7.75 e/a). Thin continuous oxide scales containing Cr2O3 and NiCr2O4 spinel formed on the surface of both alloys oxidized at 900°C for 50 h. A further increase in the annealing time to 100 h leads to the formation of aluminum oxide Al2O3 in the scale on the Fe30Ni25Co15Cr20Al10 alloy, having high protective properties. An increase in the oxidation temperature to 1000°C results in partial failure of the protective layer on the alloy with 10 at.% Al. Long-term holding at 900°C (100 h) + 1000°C (50 h) does not change the phase composition of the Fe35Ni25Co15Cr20Al5 alloy matrix, being indicative of its high thermal stability. In the two-phase Fe30Ni25Co15Cr20Al10 alloy, the quantitative ratio of solid solutions sharply changes: the amount of the bcc phase increases from 4 to 54 wt.% and its B2-type ordering is observed. The mechanical characteristics of the starting alloys and those after long-term high-temperature annealing were determined by automated indentation. The hardness (HIT) and elastic modulus (E) of the cast Fe35Ni25Co15Cr20Al5 alloy are equal to 2 and 147 GPa, respectively, and decrease to 1.8 and 106 GPa after a series of long-term annealing operations. The Fe30Ni25Co15Cr20Al10 alloy shows the opposite dependence: HIT increases from 2.5 in the initial state to 3.1 GPa after annealing and E decreases from 152 to 134 GPa. This indicates that the Fe30Ni25Co15Cr20Al10 alloy is promising as a high-temperature oxidation-resistant and creep-resistant material.

High-Temperature Annealing of Cermet Materials Based on Ti–C–NiCr

Effect of High-Temperature Annealing on the Structure and Properties of a Composite Material Based on TiC/TiB2/Ti3SiC2

Phase and crystallite size analysis of (Ti1-xMox)C-(Ni,Cr) cermet obtained by mechanical alloying

High-temperature Tribological Properties of a Novel AlFeCoNiCr-Cr3C2 Cermet Coatings

Development of composite materials based on TiN - Mo cermets during thermochemical pressing

Preparation and oxidation kinetics behavior of bulk Cr3C2-20 wt % Ni cermets

MECHANICAL PROPERTIES OF TiC-Ni PRODUCED BY SHS AT ROOM AND HIGH TEMPERATURES

Influence of annealing temperature on the structure and properties of Ti3AlC2 coatings by FCVA method

High-Temperature Oxidation Behavior of a Polycrystalline Ti2SnC Ceramic

Effect of carbon content and cooling rate on the microstructure and hardness of TiC-Fe-Cr-Mo cermets

Annealing of a (Hf0.2Ta0.2Ti0.2Nb0.2Zr0.2)C high-entropy ceramic up to 2100 °C: In-situ removal of oxide impurities and microstructural modification

Tuning microstructure for superb mechanical properties in a Ti(C,N)-(WMoTaNbTi)C-Ni/Co cermets via change sintering temperature

Cr3C2–20%Ni Cermets Prepared by High Energy Milling and Reactive Sintering, and Their Mechanical Properties

Thermal properties of spark plasma sintered Inconel 625 modified by titanium zirconium mixed carbide

Influence Of Substrate Preheating On The Structural And Phase Composition Of A Nickel-Based Cermet Coating

Microstructure and Mechanical Properties of TiC Reinforced NbC-Ni4VC4Mo2C Cermets

Influence of TaC content on microstructure and mechanical performance of Ti(C,N)-based cermets fabricated by mechanical activation and subsequent in situ carbothermal reduction

Structural State of High-Entropy Fe40–xNiCoCrAlx Alloys in High-Temperature Oxidation

Investigation of MXenes Oxidation Process during SPS Method Annealing

Thermal Stability of Microstructure and Hardness of Cold-Sprayed cBN/NiCrAl Nanocomposite Coating

Behaviors in Oxidation at 1100°C of an Equimolar CoNiFeMnCr High-Entropy Alloy and of its Versions Moderately Added with HfC or TaC Carbides