Abstract:Superior properties of titanium alloy Ti-6Al-4V over many other materials like higher strength to weight ratio, ability to maintain strength at elevated temperatures (around 500 degrees C) and ability to resist against corrosion in severe environmental conditions have made them as an excellent choice for using them in many aerospace and biomedical industrial applications. But the properties which had made them an ideal choice for most practical applications severely hinders their machinability and therefore is renowned as difficult to machine material. The low thermal conductivity of titanium alloys does not allow the generated heat to dissipate away quickly and thus results in chemical reaction with cutting tool materials at higher temperatures. Several researchers have tried to reduce tool-chip interface temperature, increase tool life and surface quality with carbide tools by applying different cutting fluids like water based emulsions flood cooling, oil flood coolant, minimum quantity lubrication MQL and various liquid nitrogen LiN cryogenic cooling techniques and has found some advantages of MQL & LiN cooling in terms of not only in improved surface roughness & tool life but also in controlling the hazardous environmental impact by eliminating the use of hazardous and expensive traditional flood coolant equipment. Moreover the thrust for higher quality and productivity has directed the attention of researchers on using super hard cutting tool materials for machining of titanium alloys. Super hard cutting tool like polycrystalline diamond PCD, Poly Cubic Boron Nitride PCBN and Binderless CBN inspite of their higher cost has many advantages over carbide tools like higher thermal conductivity, lower wear rate and high hot strength. Studies have shown that PCD tools can give better tool life and surface roughness as compared to carbide and PCBN tools. The studies on evaluating the effectiveness of PCD insert in high speed end milling of titanium alloy has not yet considered the effect of different types of cooling strategies. Therefore there is need to study the effectiveness of PCD tools in various wet cutting conditions and find optimal coolant which can help to increase tool life and can provide better surface quality and therefore this study is specifically designed to address above mentioned issues. Four different type of coolants "water based flood cooling, oil based flood coolant, MQL and LIN cryogenic cooling technique has been applied and their effect on tool-chip interface temperature, tool edge temperature, cutting forces and stresses acting on tool edge are observed using Finite element, FE numerical simulations. FE numerical simulations are widely employed in academic research field because it provides fast & reliable results and thus eliminates expensive experimentation costs which otherwise is always required. Results have shown that the LiN cooling technique has shown clear advantages over MQL and flood coolant techniques in terms of temperature near the tool rake face and in reducing cutting forces and stresses acting on cutting edge. Therefore from the study it can be concluded that LiN cooling can be used for machining of titanium alloys with PCD inserts for getting maximum productivity and part quality.

Research on Cutting Layer Characteristics of Superalloy under High-Pressure Cooling

Reaserch on Mechanism and Experimental of Chip Breaking During High Pressure Cooling Turning of Superalloys with PCBN Tool

Experimental Study on Cutting Force and Tool Wear of PCBN Tools in High-speed Turning Nickel-based Superalloy

Finite Element Analysis of High Temperature Alloy Cutting Process Based on Abaqus

Evaluating the Effectiveness of PCD Tools on Machinability of Titanium Alloy Ti-6Al-4V in High Speed End Milling under Various Wet Cutting Conditions

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Research on PCBN Tool Dry Cutting GCr15

Performance and wear mechanisms of coated PCBN tools in high-speed turning superalloy GH4202

Tool wear and surface integrity in liquid nitrogen clean cutting of cobalt-based superalloy GH605 with AlTiN coated tools

Cutting Performance and Wear/Damage Characteristics of PCBN Tool in Hard Milling

Tool Wear and Surface Integrity of γ-TiAl Cryogenic Coolant Machining at Various Cutting Speed Levels

Analysis of the material removal and heat transfer during internal cooling grinding of GH4169

Analysis of tool wear and cutting characteristics in milling of powder metallurgy nickel-based superalloy by various coatings

A review on cutting tool technology in machining of Ni-based superalloys

Mechanical Properties and Microstructure Evolution During Dynamic Compression and Cutting of Nickel-Based Superalloys

Tool wear evolution and its influence on cutting performance during milling ultra-high-strength steel using different cooling conditions

Tool Wear Mechanism and Grinding Performance for Different Cooling-Lubrication Modes in Grinding of Nickel-Based Superalloys

Green Cutting of Superalloys as Water Vapor Cooling and Lubricating

Study on Surface Integrity Modeling and Cutting Parameter Optimization of Superalloy in High-speed Finish Milling

Preliminary Experimental Study on Effect of Cutting Fluid on Milled Surface Quality of Iron-Base Superalloy

Wear and Failure Mechanisms of SiAlON Ceramic Tools During High-Speed Turning of Nickel-Based Superalloys