Abstract:In machining, heat concentration is generated at the surface contact between the tool and workpiece. This is the effect of hard frictions at the shear cutting plane to remove hard and brittle materials. The highly adhesive behavior of aluminum alloy 6061-T6 is more severe in higher cutting temperature, which may affect tool failures such as flank wear, tool chip and built-up edge, particularly on the edge of cutting inserts during the process. As a result, this may lead to the rough surface and low-dimensional accuracy of the machined parts. Realizing that metal-cutting industry players are demanding high-quality products with better surface finish and dimensional accuracy led to this study. Aluminum alloy 6061-T6 is a standard alloy used in automotive, aerospace and food packaging due to good hardness, high strength-to-weight ratio, resistance to corrosion and weldability. In order to address this problem, a newly developed metal working fluid which is SiO2-Al2O3-ZrO2 tri-hybrid nanofluid is applied in the cutting zone to achieve a good surface finish of the machined parts and lowering the cutting temperature. This study is the first attempt to enhance machining performance, particularly at high-speed machining, by employing a combination of tri-hybrid nanofluids and a minimum quantity lubricant technique. Industrial standards include uncoated tungsten carbide and CVD TiCN-Al2O3 carbide used during machining of aluminum alloy 6061-T6. The minimum quantity lubricant method is an alternative in supplying the lubricant into the machining zone due to flood machining and conventional fluid possess safety, health, economic and environmental effects. In this study, the experimental data were analyzed statistically using analysis of variance and response surface methodology. The responses studied were reduced significantly when tri-hybrid nanoparticles present at the cutting interface with higher MQL flow rate and concentration. There are two-factor interactions which are significant to the responses studied. Therefore, the combinations of MQL and excellent tri-hybrid nanofluids characteristics have enhanced between 16 and 76% of surface roughness and the cutting temperature, respectively, which is very promising in the future.

Preliminary Experimental Study on Effect of Cutting Fluid on Milled Surface Quality of Iron-Base Superalloy

Effect of cutting fluids on corrosion properties and turning surface quality of Fe-based superalloy

The effect of cutting fluids applied in metal cutting process

Research On The Cutting Fluid Effect On Cutting Force And Surface Roughness In Rotor Milling

Experimental Investigation on Machinability of Aluminum Alloy during Dry Micro Cutting Process Using Helical Micro End Mills with Micro Textures

Effect of different cooling and lubrication strategies on milling performance of ultra-high strength steel

Effects of SiO2-Al2O3-ZrO2 Tri-hybrid Nanofluids on Surface Roughness and Cutting Temperature in End Milling Process of Aluminum Alloy 6061-T6 Using Uncoated and Coated Cutting Inserts with Minimal Quantity Lubricant Method

Study on friction reduction performance of granular flow lubrication during the milling of Inconel 718 superalloy

Study on Surface Integrity Modeling and Cutting Parameter Optimization of Superalloy in High-speed Finish Milling

Experimental Study On The Effects Of Coolants On Surface Quality And Mechanical Properties Of Micromilled Thin-Walled Elgiloy

Predicting the Effects of Cutting Fluid on Machining Force, Temperature and Residual Stress Using Analytical Method.

The Effect of Superheated Water Vapor as Coolant and Lubricant on Chip Formation of Difficult-to-Cut Materials in Green Cutting

Effect of micro-textured morphology with different wettabilities on tool cutting performance

Investigation of friction in end-milling of Ti-6Al-4V under different green cutting conditions

Research on Difficult‐cut‐material in Cutting with Application of Water Vapor As Coolant and Lubricant

Study on milling surface quality of superalloy GH4145

Cooling/Lubrication Performance of Dry and Supercritical CO2-Based Minimum Quantity Lubrication in Peripheral Milling Ti-6Al-4V

Study of different cutting fluids effect on the coupling characteristics of milling noise-vibration and surface roughness of TA2 pure titanium

Molecular Dynamics Simulation Study on the Influence of the Abrasive Flow Process on the Cutting of Iron-Carbon Alloys (α-Fe)

Cutting condition effects on microstructure and mechanical characteristics of Ni-based superalloys—a review

Investigation of machinability in milling of Inconel 718 with solid Sialon ceramic tool using supercritical carbon dioxide (scCO<sub>2</sub>)-based cooling conditions