Systemic Lupus Erythematosus T Cell Studies in a Peptide-Induced Model of and Betty Diamond

M. Khalil,K. Inaba,R. Steinman,J. Ravetch,B. Diamond

Abstract:

What problem does this paper attempt to address?

Simultaneous Use of Nitrate and Calcium Peroxide to Control Sulfide and Greenhouse Gas Emission in Sewers

Guijiao Zhang,Gaowu Wang,Yongchao Zhou,David Z. Zhu,Yiping Zhang,Tuqiao Zhang

DOI: https://doi.org/10.1016/j.scitotenv.2022.158913

2023-01-01

Abstract:The sewer system is a significant source of hydrogen sulfide (H2S) and greenhouse gases which has attracted extensive interest from researchers. In this study, a novel combined dosing strategy using nitrate and calcium peroxide (CaO2) was proposed to simultaneously control sulfide and greenhouse gases, and its performance was evaluated in laboratory-scale reactors. Results suggested that the addition of nitrate and CaO2 improved the effectiveness of sulfide control. And the combination index method further proved that nitrate and CaO2 were synergistic in controlling sulfide. Meanwhile, the combination of nitrate and CaO2 substantially reduced greenhouse gas emissions, especially the carbon dioxide (CO2) and methane (CH4). The microbial analysis revealed that the combined addition greatly stimulated the accumulation of nitrate reducing-sulfide oxidizing bacteria (NR-SOB) that participate in anoxic nitrate-dependent sulfide oxidation, while the abundance of heterotrophic denitrification bacteria (hNRB) was reduced significantly. Moreover, the presence of oxygen and alkaline chemicals generated by CaO2 facilitated the inhibition of sulfate-reducing bacteria (SRB) activities. Therefore, the nitrate dosage was diminished significantly. On the other hand, the generated alkaline chemicals promoted CO2 elimination and inhibited the activities of methanogens, leading to a decrease of CO2 and CH4 fluxes, which facilitated elimination of greenhouse effects. The intermittent dosing test showed that the nitrate and CaO2 could be applied intermittently for sulfide removal. And the chemical cost of intermittent dosing strategy was reduced by 85 % compared to the continuous dosing nitrate strategy. Therefore, intermittent dosing nitrate combined with CaO2 is probably an effective and economical approach to control sulfide and greenhouse gases in sewer systems.
Control Sulfide and Methane Production in Sewers Based on Free Ammonia Inactivation.

Zhiqiang Zuo,Yarong Song,Daheng Ren,He Li,Ying Gao,Zhiguo Yuan,Xia Huang,Min Zheng,Yanchen Liu

DOI: https://doi.org/10.1016/j.envint.2020.105928

IF: 11.8

2020-01-01

Environment International

Abstract:Emissions of hydrogen sulfide and methane are two of the major concerns in sewers, causing corrosion, odour and health problems. This study proposed a new free ammonia (FA)-based approach for controlling the biological production of sulfide and methane in sewers. This is based on the discovery that the FA contained in urine wastewater is strongly biocidal to anaerobic sewer biofilms. Long-term operation of two laboratory sewer reactors, with one being dosed with urine wastewater and the other being dosed with raw sewage as a control, revealed the effectiveness of the proposed FA approach. The results showed that dosing of real urine wastewater at FA concentration of 154 mg NH3-N/L with exposure for 24 h immediately reduced over 80% sulfide and methane in the experimental sewer reactor, while the time for recovering 50% sulfide and methane production were 6 days and 28 days, respectively. It also showed that intermittent dosing with an interval time of 5–15 days reduced around 60% sulfide on average. As suggested by community analysis, the remaining sulfide might be produced by a sulfate-reducing bacterial genus Desulfobulbus. Collectively, urine is a part of municipal sewage, and thus separation and re-dosing of the urine wastewater into the sewer for sulfide and methane control should enable the minimization of operational costs and environmental impacts, compared with the previous dosing of chemicals.
Combination of Nitrate and Sodium Nitroprusside Dosing for Sulfide Control with Low Carbon Source Loss in Sewer Biofilm Reactors

Guijiao Zhang,Zhi Yang,Yongchao Zhou,David Z. Zhu,Yiping Zhang,Tong Yu,Adam Shypanski

DOI: https://doi.org/10.1016/j.jhazmat.2021.127527

IF: 13.6

2022-01-01

Journal of Hazardous Materials

Abstract:Nitrate has been widely used in sewer systems for sulfide control. However, significant chemical consumption and the loss of carbon source were observed in previous studies. To find a feasible and cost-effective control strategy of the sulfide control, the effect of nitrate combined with sodium nitroprusside (SNP) dosage strategy was tested in lab-scale sewer biofilm reactors. Results showed that nitrate and SNP were strongly synergistic, with 30 mg N/L nitrate and 20 mg/L SNP being sufficient for sulfide control in this study. While large amount of nitrate alone (100 mg N/L) is required to achieve the same sulfide control effectiveness. Meanwhile, the nitrate combined with SNP could reduce the organic carbon source loss by 80%. Additionally, the high-throughput sequencing results showed that the relative abundance of autotrophic, nitrate reducing-sulfide oxidizing bacteria genera (a-NR-SOB) such as Arcobacter and Sulfurimonas was increased by around 18%, while the heterotrophic, nitrate-reducing bacteria (hNRB) such as Thauera was substantially reduced. It demonstrated that the sulfide control was mainly due to the a-NR-SOB activity under the nitrate and SNP dosing strategy. The microbial functional prediction further revealed that nitrate and SNP promoted the dissimilatory nitrate reduction process which utilizes sulfide as an effective electron donor. Moreover, economic assessment indicated that using the combination of nitrate and SNP for sulfide control in sewers would lower the chemical costs by approximately 35% compared with only nitrate addition.
Nitrite Production from Urine for Sulfide Control in Sewers

Min Zheng,Zhiqiang Zuo,Yizhen Zhang,Yujia Cui,Qian Dong,Yanchen Liu,Xia Huang,Zhiguo Yuan

DOI: https://doi.org/10.1016/j.watres.2017.05.048

IF: 12.8

2017-01-01

Water Research

Abstract:Most commonly used methods for sewer sulfide control involves dosing chemical agents to wastewater, which incurs high operational costs. Here, we propose and demonstrate a cost-effective and environmentally attractive approach to sewer sulfide control through urine separation and its subsequent conversion to nitrite prior to intermittent dosage to sewers. Urine collected from a male toilet urinal was fed to laboratory-scale sequencing batch reactors. The reactors stably converted roughly 50% of the nitrogen in urine to nitrite, with high abundance (at 17.46%) of known ammonia-oxidizing bacteria (AOB) of the genus Nitrosomonas, and absence (below detection level) of typical nitrite-oxidizing bacteria of the genus Nitrospira, according to 454 pyrosequencing analysis. The stable nitrite production was achieved at both relatively high (1.0-2.0 mg/L) and low (0.2-0.3 mg/L) dissolved oxygen concentrations. Dosing tests in laboratory-scale sewer systems confirmed the sulfide control effectiveness of free nitrous acid generated from urine. Life cycle assessment indicated that, compared with commodity chemicals, nitrite/free nitrous acid (FNA) production from urine for sulfide control in sewers would lower the operational costs by approximately 2/3 and greenhouse gas (GHG) emissions by 1/3 in 20 years. (C) 2017 Elsevier Ltd. All rights reserved.
Nitrite-dependent Microbial Utilization for Simultaneous Removal of Sulfide and Methane in Sewers

Zhiqiang Zuo,Yaxin Xing,Xi Lu,Tao Liu,Min Zheng,Miao Guo,Yanchen Liu,Xia Huang

DOI: https://doi.org/10.1016/j.wroa.2024.100231

IF: 7.5

2024-01-01

Water Research X

Abstract:Chemicals are commonly dosed in sewer systems to reduce the emission of hydrogen sulfide (H2S) and methane (CH4), incurring high costs and environmental concerns. Nitrite dosing is a promising approach as nitrite can be produced from urine wastewater, which is a feasible integrated water management strategy. However, nitrite dosing usually requires strict conditions, e.g., relatively high nitrite concentration (e.g., ∼200 mg N/L) and acidic environment, to inhibit microorganisms. In contrast to “microbial inhibition”, this study proposes “microbial utilization” concept, i.e., utilizing nitrite as a substrate for H2S and CH4 consumption in sewer. In a laboratory-scale sewer reactor, nitrite at a relatively low concentrations of 25–48 mg N/L was continuously dosed. Two nitrite-dependent microbial utilization processes, i.e., nitrite-dependent anaerobic methane oxidation (n-DAMO) and microbial sulfide oxidation, successfully occurred in conjunction with nitrite reduction. The occurrence of both processes achieved a 58 % reduction in dissolved methane and over 90 % sulfide removal in the sewer reactor, with microbial activities measured as 15.6 mg CH4/(L·h) and 29.4 mg S/(L·h), respectively. High copy numbers of n-DAMO bacteria and sulfide-oxidizing bacteria (SOB) were detected in both sewer biofilms and sediments. Mechanism analysis confirmed that the dosed nitrite at a relatively low level did not cause the inhibition of sulfidogenic process due to the downward migration of activity zones in sewer sediments. Therefore, the proposed “microbial utilization” concept offers a new alternative for simultaneous removal of sulfide and methane in sewers.
Experimental Study on Volatile Sulfur Compound Inhibition Using a Single-Chamber Membrane-Free Microbial Electrolysis Cell

Pang Yao,Gu Tianfeng,University of Alberta,Yu Zhiguang,Zhou Yongchao,Zhu David Z.,Zhang Yiping,Zhang Tuqiao

DOI: https://doi.org/10.1007/s11356-020-09325-8

IF: 5.8

2020-01-01

Environmental Science and Pollution Research

Abstract:Odor emissions from sewer systems and wastewater treatment plants have attracted much attention due to the potential negative effects on human health. A single-chamber membrane-free microbial electrolysis cell was proposed for the removal of sulfides in a sewer system. The feasibility of the use of volatile sulfur compounds and their removal efficiency in liquid and headspace gas phases were investigated using synthetic wastewater with real sewer sediment and Ru/Ir-coated titanium electrodes. The results indicate that hydrogen sulfide and volatile organic sulfur compounds were effectively inhibited in the liquid phase upon electrochemical treatment at current densities of 1.55, 2.06, and 2.58 mA/cm2, and their removal rates reached up to 86.2–100%, except for dimethyl trisulfide, the amount of which increased greatly at 1.55 mA/cm2. In addition, the amount of volatile sulfur compounds in the headspace decreased greatly; however, the total theoretical odor concentration was still high, and methanethiol and ethanethiol greatly contributed to the total strength of the odor concentration due to their low odor threshold concentrations. The major pathway for sulfide removal in the single-chamber membrane-free microbial electrolysis cell is biotic oxidation, the removal rate of which was 0.4–0.5 mg/min, 4–5 times that of indirect electrochemical oxidation.
Effects of Intermittent Chemical Dosing on Volatile Sulfur Compounds in Sewer Headspace

Guijiao Zhang,Tianfeng Gu,Yongchao Zhou,David Z. Zhu,Yiping Zhang

DOI: https://doi.org/10.4491/eer.2021.091

2022-01-01

Environmental Engineering Research

Abstract:Volatile sulfur compounds (VSCs), including hydrogen sulfide (H2S) and volatile organic sulfide compounds (VOSCs), can be produced in sewer systems causing sewer odor problems. In this study, the effects of intermittently dosing ferric iron, hydrogen peroxide, and nitrate on H2S and VOSCs in sewer headspace were investigated. In order to characterize the composition of VSCs, an HC-3 trace sulfur analyzer and gas chromatograph (GC) equipped with a triple quadrupole-type mass spectrometry (MS) apparatus were used to determine the VSCs. The results indicated that the effect of intermittent addition of 40 mg/L ferric iron or 40 mg/L hydrogen peroxide is limited for VSCs inhibition. The H2S and VOSCs concentrations increased significantly in the late-stage experiments, even around 20% and 30% respectively higher than the initial average concentrations. However, the intermittent addition of 40 mg N/L nitrate has a relatively stable control effect of H2S and VOSCs which maintaining 60% removal rate. Moreover, methyl mercaptan (MeSH) was the most abundant compound of the total VOSCs released and the results of the theoretical odor concentration study also indicate MeSH is the main VOSC causing the significant odor problem. Therefore, more attention should be focused on the VOSCs which have extremely low odor threshold.
Simultaneous Control of Sulfide and Methane in Sewers Achieved by a Physical Approach Targeting Dominant Active Zone in Sediments

Daheng Ren,Zhiqiang Zuo,Yaxin Xing,Penghui Ji,Tong Yu,David Zhu,Yanchen Liu,Xia Huang

DOI: https://doi.org/10.1016/j.watres.2021.118010

IF: 12.8

2022-01-01

Water Research

Abstract:Sewer sediments not only induce sewer blockages, but also contributes to significant sulfide and methane productions in gravity sewer systems. Chemical control of sulfide and methane production is extremely expensive. This study aims to propose a novel physical control approach-intermittent surface sediment flushing to synchronously address sediment-induced multiple issues. The proposed approach was established investigating the suppression and recovery characteristics of sulfidogenic and methanogenic activities of sediments including the in-situ activity analysis by using the diffusive gradients in thin films (DGT). The results showed that similar to 70% of total sulfide and methane production in sediments was contributed by surface sediments (0-1.5 cm), which could be easily flushed away by a low shear stress (<0.1 N/m(2)). Surface sediment flushing resulted in an immediate reduction in sulfidogenic and methanogenic activities, which both required about one week to recover to 50% of the maximum. These novel insights hopefully provide a feasible approach, i.e. , intermittent surface sediment flushing, to effectively reduce sulfide and methane production in sewers. Compared with chemical dosing methods, the proposed approach, which has no chemical input, greatly reduces operating cost and environment impact. Moreover, intermittent surface flushing is expected to keep sediment thickness within a certain range to alleviate sewer blockage.
Sulfide Elimination by Intermittent Nitrate Dosing in Sewer Sediments

Yanchen Liu,Chen Wu,Xiaohong Zhou,David Z. Zhu,Hanchang Shi

DOI: https://doi.org/10.1016/j.jes.2014.06.038

IF: 6.9

2014-01-01

Journal of Environmental Sciences

Abstract:The formation of hydrogen sulfide in biofilms and sediments in sewer systems can cause severe pipe corrosions and health hazards, and requires expensive programs for its prevention. The aim of this study is to propose a new control strategy and the optimal condition for sulfide elimination by intermittent nitrate dosing in sewer sediments. The study was carried out based on lab-scale experiments and batch tests using real sewer sediments. The intermittent nitrate dosing mode and the optimal control condition were investigated. The results indicated that the sulfide-intermittent-elimination strategy by nitrate dosing is advantageous for controlling sulfide accumulation in sewer sediment. The oxidation–reduction potential is a sensitive indicator parameter that can reflect the control effect and the minimum N/S (nitrate/sulfide) ratio with slight excess nitrate is necessary for optimal conditions of efficient sulfide control with lower carbon source loss. The optimal control condition is feasible for the sulfide elimination in sewer systems.
Enhanced mechanistic insights and performance optimization: Controlling methane and sulfide in sewers using nitrate dosing strategies

Yan Chen,Yaxin Xing,Zhiqiang Zuo,Guangming Jiang,Hongping Min,Dingding Tang,Peng Liang,Xia Huang,Yanchen Liu

DOI: https://doi.org/10.1016/j.scitotenv.2023.167580

IF: 9.8

2023-11-05

The Science of The Total Environment

Abstract:Nitrate has been used for nearly 80 years as a chemical to control problematic gases in the sewer system. However, few studies have explored simultaneous control in biofilm and sediment using different strategies. Here, we introduced a nitrate dosing method involving an initial high shock followed by low level dosing, tested at two distinct frequencies in a lab-scale sewer reactor <110 days. Long-term investigation revealed that the more frequent 20 min interval dosing slightly surpassed the 1 h interval method when applying the same hourly dose of 30 mg N/L (sulfide control: 98.3 ± 1.7 % vs 97.9 ± 1.5 %; methane control: 89.8 ± 4.5 % vs 83.4 ± 6.7 %). 16 s rRNA gene amplicon sequencing revealed biofilm detachment and sediment stratification, which can be attributed to the differing effects of nitrate dosing on biofilm and sedimentary microbial interactions. Dominant bacteria such as Thauera and Thiobacillus performed autotrophic denitrification and nitrate-reducing sulfide-oxidation in conjunction with methane oxidizers. These microbes collaboratively control sulfide and methane emissions from sediment. Our findings suggest that nitrate supports the diversity and versatility of their metabolism in the sewer system.

environmental sciences
Characteristics and Mechanism of Dimethyl Trisulfide Formation During Sulfide Control in Sewer by Adding Various Oxidants

Tianfeng Gu,Peiying Tan,Yongchao Zhou,Yiping Zhang,David Zhu,Tuqiao Zhang

DOI: https://doi.org/10.1016/j.scitotenv.2019.04.131

2019-01-01

Abstract:The addition of chemical agents to control the production of hydrogen sulfide (H2S) is currently the principal technology used to control odor emissions from sewers. In this study, laboratory reactors were used to investigate the change in dimethyl trisulfide (DMTS) concentrations when dosing with oxidant to control sulfide in sewers. Our results show that the intermittent addition of oxidant leads to sulfide regeneration and increased DMTS formation. Additional experiments were conducted to investigate the processes that result in the formation of DMTS. The results indicate that the polysulfide produced after oxidant addition was a key intermediate in DMTS production. Enzymatic methylation of polysulfide was an important process in DMTS formation. Dimethylsulfoxide (DMSO) was observed in the reactor when oxidant was again added but it was reduced to DMTS when the oxidant was depleted. There are side-effects of adding oxidant, and alternative control measures for volatile sulfur compounds (VSCs) need to be investigated further.
In-situ Advanced Oxidation of Sediment Iron for Sulfide Control in Sewers

Yanchen Liu,Zhiqiang Zuo,He Li,Yaxin Xing,Dong Cheng,Miao Guo,Tao Liu,Min Zheng,Zhiguo Yuan,Xia Huang

DOI: https://doi.org/10.1016/j.watres.2023.120077

IF: 12.8

2023-01-01

Water Research

Abstract:Sulfide control is a significant problem in urban sewer management. Although in-sewer dosing of chemicals has been widely applied, it is prone to high chemical consumption and cost. A new approach is proposed in this study for effective sulfide control in sewers. It involves advanced oxidation of ferrous sulfide (FeS) in sewer sediment, to produce hydroxyl radical (.OH) in-situ, leading to simultaneous sulfide oxidation and reduction of microbial sulfate-reducing activity. Long-term operation of three laboratory sewer sediment reactors was used to test the effectiveness of sulfide control. The experimental reactor with the proposed in-situ advanced FeS oxidation substantially reduced sulfide concentration to 3.1 +/- 1.8 mg S/L. This compares to 9.2 +/- 2.7 mg S/L in a control reactor with sole oxygen supply, and 14.1 +/- 4.2 mg S/L in the other control reactor without either iron or oxygen. Mechanistic investigations illustrated the critical role of .OH, produced from the oxidation of sediment iron, in regulating microbial communities and the chemical sulfide oxidation reaction. Together these results demonstrate that incorporating the advanced FeS oxidation process in sewer sediment enable superior perfor-mance of sulfide control at a much lower iron dosage, thereby largely saving chemical use.
A Biological Strategy for Sulfide Control in Sewers: Removing Sulfide by Sulfur-Oxidizing Bacteria.

Xin Yuan,Yiquan Sun,Dong Ni,Zhenwen Xie,Yanyan Zhang,Sun Miao,Linjun Wu,Xin Xing,Jiane Zuo

DOI: https://doi.org/10.1016/j.jenvman.2023.119237

IF: 8.7

2023-01-01

Journal of Environmental Management

Abstract:Sulfide produced from sewers is considered one of the dominant threats to public health and sewer lifespan due to its toxicity and corrosiveness. In this study, we developed an environmentally friendly strategy for gaseous sulfide control by enriching indigenous sulfur-oxidizing bacteria (SOB) from sewer sediment. Ceramics acted as bio-carriers for immobilizing SOB for practical use in a lab-scale sewer reactor. 16 S rRNA gene sequences revealed that the SOB consortium was successfully enriched, with Thiobacillus, Pseudomonas, and Alcaligenes occupying a dominant abundance of 64.7% in the microbial community. Metabolic pathway analysis in different acclimatization stages indicates that microorganisms could convert thiosulfate and sulfide into elemental sulfur after enrichment and immobilization. A continuous experiment in lab-scale sewer reactors confirmed an efficient result for sulfide removal with hydrogen sulfide reduction of 43.9% and 85.1% under high-sulfur load and lowsulfur load conditions, respectively. This study shed light on the promising application for sewer sulfide control by biological sulfur oxidation strategy.
Improving contaminant removal and inhibiting CH4 and H2S emissions from septic tanks: Nitrified human urine as a source of electron acceptor

Zhenchao Gao,Zhongguo Zhang,Qingyun Li,Haoyuan Wu,Mengyu Wang,Xiujun Tian,Aimin Wang,Jiuyi Li

DOI: https://doi.org/10.1016/j.scitotenv.2024.175410

2024-08-08

Abstract:Septic tanks are widely adopted in decentralized household wastewater treatment systems serving billions of people globally. Due to the lack of effective electron acceptors, insufficient nutrient removal and the emission of harmful gases, e. g. H2S, CH4, etc., are the common drawbacks. In the present work, we attempted to supplement nitrite into septic tanks as an electron acceptor, via nitrifying human urine source-separated from blackwater, to overcome these drawbacks. Partial or complete nitritation of source-separated urine was achieved in a sequencing batch reactor. The addition of nitrified urine into septic tanks improved organic and nitrogen removals in blackwater up to 90 % and 70 %, respectively. The emission of harmful gases from the septic tanks was stably diminished, with more than 75 % of CH4, CO2 and H2S reductions. Nitrite addition significantly reduced the abundance of hydrogenotrophic methanogens in septic tanks. Though the activity of sulfate-reducing bacteria recovered after the initial inhibition upon nitrite addition, the bio-generated H2S was retained in water since the increased wastewater pH after nitrite addition promoted the disassociation of H2S in aqueous solution.
Free Nitrous Acid-Based Suppression of Sulfide Production in Sewer Sediments: In-situ Effect Mechanism

Zhiqiang Zuo,Min Zheng,Jian Chang,Daheng Ren,Xia Huang,Zhiguo Yuan,Yanchen Liu

DOI: https://doi.org/10.1016/j.scitotenv.2020.136871

IF: 9.8

2020-01-01

The Science of The Total Environment

Abstract:Sulfide production control in gravity sewer sediments is more complex and difficult due to the greater spatial complexity of biological processes as a result of the abundant microflora inside the sediments. In this study, a promising and cost-effective free nitrous acid (FNA)-based suppression strategy for sulfide production in sewer sediments was proposed. Novel in-situ measurement methods were implemented by incorporating the diffusive gradients in thin films (DGT) technique and high-resolution dialysis (HR-Peeper) with microbial characterization analysis along the vertical sediment profile to examine the effect mechanism of the FNA-based inhibition process on sulfide production in the sediments. The results revealed that the FNA-based exposure strategy could effectively suppress the sulfidogenic activity across the whole shallow active layer (approximately 0.5 cm below the surface) in the sediments. An initial high FNA concentration up to 2.5 mg HNO2-N/L was required to maintain a critical inhibition level (24-h average concentration > 0.2 mg HNO2-N/L) across the whole active sediment zone. The FNA concentration decreased sharply deeper than 0.5 cm with a significant pH increase, resulting in FNA inactivation only reducing the microbial live/total ratio and shifting the microbial community structure near the sediment surface. Maintaining a low pH is the critical factor for the FNA-based suppression strategy of the sulfidogenic activity in the shallow sediment zone.
In Situ Exploration of the Sulfidogenic Process at the Water-Sediment Interface in Sewers: Mechanism and Implications

Zhiqiang Zuo,Zheng Sun,Yizhen Zhang,Moran Wang,Daheng Ren,Siqi Li,Zhiguo Yuan,Yanchen Liu,Xia Huang

DOI: https://doi.org/10.1021/acsestengg.0c00163

IF: 7.1

2020-01-01

ACS ES&T Engineering

Abstract:Corrosion and odor induced by sulfidogenic processes is a worldwide issue in environmental engineering. This study focuses on a neglected, but critical process, sulfidogenic conversion at the water-sediment interface, to optimize the prediction and control of sulfide in sewers. A novel in situ, high-resolution measurement method based on the diffusive gradients in thin films technique was established for the first time for use in sewer systems. The results showed that, at a critical shear velocity (i.e., similar to 0.07 m/s), the key factor dominating sulfidogenic activity in the surface layer of sediment (i.e., similar to 1 cm) switched to substrate diffusion resistance at the water-sediment surface. An increase in shear velocity from 0 to similar to 0.07 m/s significantly activated the sulfidogenic process in this layer. The spatial variation in the functional microbial community further confirmed the sediment profile of sulfidogenic activity. A sewer model incorporating the substrate diffusion process at the water-sediment interface was developed and verified, which revealed the characteristic response of the diffusive boundary layer thickness at the water-sediment interface to shear velocity. The maximum sulfide production rates (k(H2S)) under varying water quality and shear velocity conditions were successfully simulated, improving the model's predictive accuracy in gravity sewers. This study has certain engineering significance for optimizing sulfide prediction and control in sewers.
Control of Ammonification of Source-separated Urine

Kang-ning XU,Tao XIE,Xiang-hui WANG,Chi ZHANG,Ji-yun LI,Cheng-wen WANG

DOI: https://doi.org/10.19853/j.zgjsps.1000-4602.2014.19.005

2014-01-01

Abstract:Urine source separation has been considered to be a sustainable alternative for the traditional sewerage system.However,scaling on urine-collecting pipes and loss of nitrogen and phosphorus during urine ammonification limited the promotion and application of the new technique.Therefore,control of ammonification was investigated in laboratory scale,and the effect on scaling potential was analyzed.The results showed that low temperature of 5 ℃ could completely inhibit the ammonification process and the scaling potential in 25 d but with low operability.Further,the scaling potential was immediately increased although alkaline p H could inhibit the urine ammonification.Finally,dosing of urease inhibitor n BPT was found to be a possible approach to control urine ammonification.Dosage of0.75% was suggested for controlling ammonification for 3 d while dosage of 1.5% was suggested for 7 d.
Rapid Dynamic Quantification of Sulfide Generation Flux in Spatially Heterogeneous Sediments of Gravity Sewers

Zhiqiang Zuo,Daheng Ren,Longkai Qiao,He Li,Xia Huang,Yanchen Liu

DOI: https://doi.org/10.1016/j.watres.2021.117494

IF: 12.8

2021-01-01

Water Research

Abstract:Compared with anaerobic pressure sewers, gravity sewers have much more complex operational conditions, such as anaerobic/aerobic spatial variations along variable structures of the pipe network. This greatly complicates the prediction of sulfide generation from spatially heterogeneous sewer sediments. This study proposes a novel quantitative approach for rapidly estimating the sulfide generation flux by understanding the sulfidogenic conversion under complex sewer conditions. Significant anaerobic/aerobic spatial variations were the most critical factor affecting the sulfide production in residential gravity sewers. The dynamic aeration-related process stimulated the growth of sulfide-oxidizing bacteria (SOB) in the surface zone, while the sulfidogenic and methanogenic zone moved into deeper layers. A detailed mechanism model incorporating dynamic alternative anaerobic/aerobic transformation was developed to predict apparent sulfide production, as well as the microscale spatial profiles of chemicals and microbial communities in sediments. The model was evaluated to establish a rapid quantitative approach that only depended on a few key parameters (e.g., flow velocity, pipe diameter, slope, mean hydraulic depth and sulfate concentration), which can provide an important basis for estimating different sulfide generation fluxes under various sewer factors. The identification of sulfide generation hotspots will greatly help determine how to economically control sulfide generation by chemical dosing or pipe structural modification.
Long-term field test of an electrochemical method for sulfide removal from sewage

Ilje Pikaar,Eugena Li,René A. Rozendal,Zhiguo Yuan,Jürg Keller,Korneel Rabaey

DOI: https://doi.org/10.1016/j.watres.2012.03.013

IF: 12.8

2012-06-01

Water Research

Abstract:Corrosion caused by hydrogen sulfide leads to significant costs for the rehabilitation or replacement of corroded sewer pipes. Conventional methods to prevent sewer corrosion normally involve the dosing of significant amounts of chemicals with the associated transport and storage costs as well as considerable maintenance and control requirement. Recently, a novel chemical free method for sulfide abatement based on electrochemical sulfide oxidation was shown to be highly effective for the removal of sulfide from synthetic and real sewage. Here, we report on the electrochemical removal of sulfide using Ta/Ir and Pt/Ir coated titanium electrodes under simulated sewer conditions during field trials. The results showed that sulfide can successfully be removed to levels below the normal target value at the end of a simulated rising main (i.e. <1mg/L). A coulombic efficiency for dissolved oxygen generation of ≈ 60% was obtained and was independent of the current density. Scaling of the electrode and the membrane was observed in the cathode compartment and as a result the cell potentials increased over time. The cathode potentials returned to their original potential after switching the polarity every two days, but a more frequent switching would be needed to reduce the energy requirements of the system. Accelerated lifetime experiments indicated that a lifetime of 6.0 ± 1.9 years can be expected under polarity switching conditions at a pH of 14 and significantly longer at lower pH values. As operating the system without switching simplifies construction as well as operation, the choice whether to switch or not will in practice depend on operational cost (higher/lower energy) versus capital cost (reactor and peripherals). Irrespective of the approach, our study demonstrates that electrochemical sulfide control in sewer systems may be an attractive new option.

environmental sciences,engineering, environmental,water resources
Regulating the Dechlorination and Methanogenesis Synchronously to Achieve a Win-Win Remediation Solution for Γ-Hexachlorocyclohexane Polluted Anaerobic Environment.

Jie Cheng,Shuyao Li,Xueling Yang,Xiaowei Huang,Zhijiang Lu,Jianming Xu,Yan He

DOI: https://doi.org/10.1016/j.watres.2021.117542

IF: 12.8

2021-01-01

Water Research

Abstract:The wish for rapid degradation of chlorinated organic pollutants along with the increase concern with respect to greenhouse effect and bioenergy methane production have created urgent needs to explore synchronous regulation approach. Microbial electrolysis cell was established under four degressive cathode potential settings (from -0.15V to -0.60V) to regulate γ-hexachlorocyclohexane (γ-HCH) reduction while CH4 cumulation in this study. The synchronous facilitation of γ-HCH reduction and CH4 cumulation was occurred in -0.15V treatment while the facilitation of γ-HCH reductive removal together with the inhibition of CH4 cumulation was showed in -0.30V treatment. Electrochemical patterns via cyclic voltammetry and morphological performances via scanning electron microscopy illustrated bioelectrostimulation promoted redox reactions and helped to construct mature biofilms located on bioelectrodes. Also, bioelectrostimulated regulation pronouncedly affected the bacteria and archaeal communities and subsequently assembled distinctly core sensitive responders across bioanode, biocathode and plankton. Clostridum, Longilinea and Methanothrix relatively accumulated in the plankton, and Cupriavidus and Methanospirillum, and Perimonas and Nonoarcheaum in biocathode and bioanode, respectively; while Pseudomonas, Stenotrophomonas, Methanoculleus and Methanosarcina were diffusely enriched. Microbial interactions in the ecological network were more complicated in -0.15V and -0.30V cathodic potential treatments, coincident with the increasement of γ-HCH reduction. The co-existence between putative dechlorinators and methanogens was less significant in -0.30V treatment when compared to that in -0.15V treatment, relevant with the variations of CH4 cumulation. In all, this study firstly corroborated the availability to synchronously regulate γ-HCH reductive removal and methanogenesis. Besides, it paves an advanced approach controlling γ-HCH reduction in cooperation with CH4 cumulation, of which to achieve γ-HCH degradation facilitation along with biogas (CH4) production promotion with -0.15V cathode potential during anaerobic γ-HCH contaminated wastewater digestion, or to realize γ-HCH degradation facilitation with the inhibition of CH4 emission with -0.30V cathode potential for an all-win remediation in γ-HCH polluted anaerobic environment such as paddy soil.

Systemic Lupus Erythematosus T Cell Studies in a Peptide-Induced Model of and Betty Diamond

Simultaneous Use of Nitrate and Calcium Peroxide to Control Sulfide and Greenhouse Gas Emission in Sewers

Control Sulfide and Methane Production in Sewers Based on Free Ammonia Inactivation.

Combination of Nitrate and Sodium Nitroprusside Dosing for Sulfide Control with Low Carbon Source Loss in Sewer Biofilm Reactors

Nitrite Production from Urine for Sulfide Control in Sewers

Nitrite-dependent Microbial Utilization for Simultaneous Removal of Sulfide and Methane in Sewers

Experimental Study on Volatile Sulfur Compound Inhibition Using a Single-Chamber Membrane-Free Microbial Electrolysis Cell

Effects of Intermittent Chemical Dosing on Volatile Sulfur Compounds in Sewer Headspace

Simultaneous Control of Sulfide and Methane in Sewers Achieved by a Physical Approach Targeting Dominant Active Zone in Sediments

Sulfide Elimination by Intermittent Nitrate Dosing in Sewer Sediments

Enhanced mechanistic insights and performance optimization: Controlling methane and sulfide in sewers using nitrate dosing strategies

Characteristics and Mechanism of Dimethyl Trisulfide Formation During Sulfide Control in Sewer by Adding Various Oxidants

In-situ Advanced Oxidation of Sediment Iron for Sulfide Control in Sewers

A Biological Strategy for Sulfide Control in Sewers: Removing Sulfide by Sulfur-Oxidizing Bacteria.

Improving contaminant removal and inhibiting CH4 and H2S emissions from septic tanks: Nitrified human urine as a source of electron acceptor

Free Nitrous Acid-Based Suppression of Sulfide Production in Sewer Sediments: In-situ Effect Mechanism

In Situ Exploration of the Sulfidogenic Process at the Water-Sediment Interface in Sewers: Mechanism and Implications

Control of Ammonification of Source-separated Urine

Rapid Dynamic Quantification of Sulfide Generation Flux in Spatially Heterogeneous Sediments of Gravity Sewers

Long-term field test of an electrochemical method for sulfide removal from sewage

Regulating the Dechlorination and Methanogenesis Synchronously to Achieve a Win-Win Remediation Solution for Γ-Hexachlorocyclohexane Polluted Anaerobic Environment.