Latinos on Race and Ethnicity : Alcoff , Corlett , and Gracia

Susana Nuccetelli,Ofelia M. Schutte,O. Bueno

Abstract:

What problem does this paper attempt to address?

Study on interface modification and tribological properties of MCMB-SiC self-lubricating composites

Jialin Bai,Shijie Huang,Xiumin Yao,Xuejian Liu,Zhengren Huang

DOI: https://doi.org/10.1016/j.triboint.2024.109253

IF: 5.62

2024-01-10

Tribology International

Abstract:Mesocarbon microbead-silicon carbide (MCMB-SiC) composites are promising candidates for mechanical seals of nuclear reactor main pumps due to their adaptability to severe environments. However, the weak bonding strength between MCMB and SiC matrix causes an unstable dry friction coefficient, which limits its further development. Herein, the interface-modified MCMB-SiC composites were prepared by hot-pressing sintering using liquid vinyl hydrido polycarbosilane (VHPCS) coated raw material powder for the first time. The pyrolytic VHPCS was loaded on the surface of MCMB particles. The effects of VHPCS content on the microstructure, mechanical properties, and dry tribological properties of MCMB-SiC composites were systematically studied. The results show that the MCMB-SiC composites with 1 wt% VHPCS (MS-P1) had good comprehensive mechanical properties. Meanwhile, compared to MCMB-SiC composites without VHPCS (MS-P0), MS-P1 exhibited improved dry friction properties, with a dry friction coefficient (μ) reduced by ∼25% (0.18) and a wear rate (W R ) reduced by ∼35% (7.69 ×10 −7 mm 3 ·N −1 ·m −1 ). It was considered to be due to the nano-SiC grains generated by VHPCS after sintering improved the interface strength between MCMB and SiC matrix, which inhibited the detachment of hard SiC particles during the friction process. In addition, sufficient C-Si-O lubricating film can fill the pits, which acts as a self-healing effect. This study provides an effective route to improve the tribological properties of MCMB-SiC self-lubricating composites with high carbon content.

engineering, mechanical
A Study of Tribological Performance and Tribo-Induced Graphitization of Meso-Carbon Microbeads

Cui Xiaohao,Li Shenghua,Jin Yuansheng,Song Huaihe

DOI: https://doi.org/10.1023/A:1021717000880

2003-01-01

Tribology Letters

Abstract:The tribological behavior of meso-carbon microbead (MCMB) powders of micron sizes extracted from heat-treated coal tar pitches was monitored on an Optimal SRV tribotester at 300 °C and 250N when blended as special boundary lubrication improvers into a pentaerythritol base oil. Structures of the original MCMB were revealed with TEM to be of layers of various sizes governed by the heat-treatment intensity in the manufacturing process. Raman spectroscopic analyses of the worn areas of steel tribomate indicated that the MCMB with richer initial ordered structures would be beneficial to the tribological transformation. A deduced correlation of the measured size of the yielded graphitic microcrystallites and the calculated friction heat-treatment intensity ( W ) justified the ease of the tribological transformation of the more ordered initial structures of MCMB.
Tribological properties of reaction-formed graphite/SiC composites under water-lubricated conditions

Peng Su,Rong Xue,Qianhui Qin,Meixia Cai,Jiping Wang,Hongyan Xia,Zhichao Xiao

DOI: https://doi.org/10.1016/j.ceramint.2024.02.235

IF: 5.532

2024-02-01

Ceramics International

Abstract:Graphite/SiC composites with excellent tribological properties and chemical stability are ideal bearing materials for use in water-lubricated conditions. The composites can be fabricated rapidly by reactive melt infiltration (RMI) with near-net advantages. However, maintaining an adequate carbon content in the matrix after the violent reaction between carbon and liquid silicon is the critical requirement for wear rate and more stable friction coefficient. In this study, a carbon-composite-powder (PFC@G) constructed of graphite particles and glassy carbon derived from phenolic resin, was used as the main carbon source with a larger size (∼200 μm) to improve the carbon content of the graphite/SiC composites. The tribological properties of the composites were measured by a block-on-ring tribometer under water-lubricated conditions. The weight ratio of phenolic resin to graphite particles was adjusted to manipulate the microstructure of PFC@G, which can affect the carbon content of the composites in the course of RMI. The composites with high carbon content (34.47 vol%) were successfully fabricated when the weight ratio is 0.8, which exhibited the most outstanding tribological properties with low friction coefficient (∼0.014) and wear rate (∼10−6 mm3 N−1m−1) at a load of 15 N.

materials science, ceramics
Enhancement of Tribological Properties in Siliconized Graphite Via Hierarchically Hybrid SiC/C Composite

Zilin Li,Zhaowei Zhu,Xianglong Yu,Kai Li,Zixi Wang,Zezhao Zhang,Yuming Wang

DOI: https://doi.org/10.1016/j.pnsc.2020.12.014

IF: 4.269

2021-01-01

Progress in Natural Science Materials International

Abstract:This study aims to investigate tribological properties in a siliconized graphite (СГ-П-0.5) and hierarchically hybrid SiC/C composites at the load ranging from 10-40 N under dry air/water lubrication conditions. A feasible liquid silicon infiltration (LSI) was used to fabricate the SiC/C composites. Morphology and phase identification of two materials were characterized and analyzed by scanning electron microscope (SEM) and energy dispersive spectrometer (EDS). An image feature extraction was used to post-process the data of wear test, further to gain the wear properties of the samples. The results demonstrated that a lower coefficient of friction (COF) and wear rate can be achieved in the LSI SiC composites than that in the sample of СГ-П-0.5. Both COF decreased under water-lubricated conditions, compared with that under the dry air lubrication. The excellent tribological properties in two materials can be due mainly to the microstructure of the СГ-П-0.5 sample, showing much more graphite and Si dispersed on the matrix. The СГ-П-0.5 sample indicated the typical oxidative wear mechanism, whereas, the sample of LSI SiC demonstrated the combined oxidative and fatigue wear. This finding can provide a promising new siliconized graphite materials for ceramic rolling bearings.
Fabrication and mechanical properties of in situ prepared mesocarbon microbead/carbon nanotube composites

Bin Wu,Zhi Wang,Qian Ming Gong,Huai He Song,Ji Liang

DOI: https://doi.org/10.1016/j.msea.2007.10.070

2008-01-01

Abstract:Carbon nanotubes (CNTs)-doped mesophase spherules were prepared from coal tar pitch blended with CNTs by in situ method after heat-treated at 420°C for 120–150min. Mesocarbon microbead/carbon nanotube (MCMB/CNT) composite blocks were successfully obtained after compaction and calcination. The morphology and microstructure of the composites indicate that the added CNTs enhance the nucleation and restrict the growth and coalescence of the mesophase spherules. The relatively higher flexural strength of 146MPa and compressive strength of 439MPa were obtained with CNTs content of about 2–5wt.%, while excess amount of CNTs over 10% led to mechanical property deterioration because of CNTs agglomeration. The strengthening effect of proper CNTs addition is attributed to voids reduction and reinforced interstitial substance between the microbeads. It is also indicated that better dispersion of more CNTs with large lengths in the matrix would offer more space to enhance mechanical properties of MCMB/CNT composites.
Effect of Oxidative Stabilization on the Sintering of Mesocarbon Microbeads and A Study of Their Carbonization

Ke Shen,Zheng-Hong Huang,Junhe Yang,Wanci Shen,Feiyu Kang

DOI: https://doi.org/10.1016/j.carbon.2011.03.044

IF: 10.9

2011-01-01

Carbon

Abstract:Graphite artifacts were prepared using mesocarbon microbeads (MCMBs) with two different extents of oxidation, lightly oxidized MCMBs (M-LO) and highly oxidized MCMBs (M-HO). Cold isostatic pressing at 200MPa was used in the formation process. Physical properties of the obtained artifacts prepared with two raw materials are quite different, the reason can be found in their pyrolysis behavior and sintering behavior. Thermogravimetry–mass spectrometer results show that H2, CH4, CO2 and H2O are the common gaseous products, however, between 400 and 600°C the M-LO may generate lightweight hydrocarbon component which was confirmed by thermogravimetry–infrared spectroscopy. A remarkable difference between the flexural strength of M-LO and M-HO was explained by the microstructure evolution observed with in situ scanning electron microscopy. For M-LO, cracks are mainly transgranular, giving little chance for interconnection, while in M-HO, cracks are mainly intergranular and may connect to form long cracks. A mechanism of crack formation caused by inhomogeneous shrinkage was proposed.
Effect of Carbon in Fabrication Al-SiC Nanocomposites for Tribological Application

Bartosz Hekner,Jerzy Myalski,Tomasz Pawlik,Małgorzata Sopicka-Lizer

DOI: https://doi.org/10.3390/ma10060679

2017-06-21

Abstract:Aluminium-based hybrid composites are a new class of advanced materials with the potential of satisfying the demands in engineering applications. This paper describes the effects of carbon addition on the formation and properties of AMC with SiC nanoparticles reinforcement. The composites were produced via mechanical alloying followed by hot pressing. Three forms of carbon, graphite (GR), multiwalled carbon nanotubes (CNTs), and, for the first time, glassy carbon (GC), were used for the hybrid composites manufacturing and compared with tribological properties of Al-SiC composite without carbon addition. GC and CNTs enhanced formation of Al-SiC composite particles and resulted in a homogeneous distribution of reinforcing particles. On the other hand, GR addition altered mechanochemical alloying and did not lead to a proper distribution of nanoparticulate SiC reinforcement. Hot pressing technique led to the reaction between Al and carbon as well as SiC particles and caused the formation of Al₄C₃ and γ-Al₂O₃. The subsistence of carbon particles in the composites altered the predominant wear mechanisms since the wear reduction and the stabilization of the friction coefficient were observed. GC with simultaneous γ-Al₂O₃ formation in the hybrid Al-SiC(n)-C composites turned out to be the most effective additive in terms of their tribological behaviour.
Microstructure, mechanical and tribological properties of multilayer grapheme reinforced WC-10Ni 3 Al prepared by microwave sintering

Ji Lu,Siwen Tang,Lingyan Tang,Meilian Gao,Qian Liu,Qiulin Niu

DOI: https://doi.org/10.1016/j.jmrt.2023.09.116

IF: 6.267

2023-09-19

Journal of Materials Research and Technology

Abstract:The multilayer graphene (MLG) reinforced WC-10Ni 3 Al cemented carbide was prepared by microwave sintering. The effects of the sintering temperature and MLG content on the microstructure and mechanical properties of the WC-10Ni 3 Al cemented carbide were investigated. The promotion effect and strengthening mechanism of MLG on WC-10Ni 3 Al by microwave sintering were explored. The tribological properties of WC-10Ni 3 Al and Ti6Al4V(TC4) were studied, and the wear mechanism of WC-10Ni 3 Al was revealed. The experiment result show that the WC-10Ni 3 Al-0.5 wt.% MLG sample sintered at 1450°C had its greatest mechanical properties with a relative density of 96.9%, hardness of 1430 HV, flexural strength of 1410 MPa and fracture toughness of 15.7 MPa·mm 1/2 , which were 4.2%, 12.2%, 24.4%, and 29.6% greater than those of the sample without MLG added, respectively. The reinforcing and toughening mechanisms of adding MLG in WC-10Ni 3 Al samples consist of fine crystal strengthening, crack bridging and deflection, MLG pulling out and bridging. The results of friction experiment show that the friction coefficient and wear rate of the WC-10Ni 3 Al samples were lower than those of YG8 (WC-8 wt. % Co cemented carbide). The WC-10 Ni 3 Al-0.5 wt.% MLG sample obtained the lowest friction coefficient of 0.35 and the lowest wear rate of 1.69 × 10 -5 mm 3 N -1 m -1 . A stable solid lubrication film was produced on the friction surface of the WC-10Ni 3 Al samples, which was conducive to reducing the breakage and wear of WC grains. MLG can enhance the stability of solid lubrication film and reduce its friction coefficient.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Effect of sintering temperature on microstructure and tribological properties of copper/graphite composites doped with Ti3AlC2 particles

Yuanming Su,Feng Jiang,Feifei Wu,Mengjun Long

DOI: https://doi.org/10.1016/j.mtcomm.2024.108136

IF: 3.8

2024-03-01

Materials Today Communications

Abstract:Copper/graphite composites have received much attention in engineering applications due to their excellent thermal, electrical and self-lubricating properties. However, their mechanical and wear resistance properties are usually limited by the brittleness of graphite and the poor interfacial bond between graphite and copper. Harder particles can be used to reinforce composites to increase their mechanical properties and wear resistance. In this paper, copper/graphite composites added with Ti3AlC2 particles were prepared by rapid hot press sintering. Studies were conducted to find out how the sintering temperature affected the composites' phase composition, morphology, hardness, relative density, and friction properties. The results showed that the relative density and hardness of the composites increased and then decreased with increasing sintering temperature. Besides, the findings indicated that Al atoms started to diffuse out of Ti3AlC2 and into the Cu matrix around 800 °C, leading to the in-situ formation of TiCx and Cu(Al) alloys. When the sintering temperature exceeded 850 °C, Ti3AlC2 decomposed essentially completely. In comparison to other similar prior findings (the wear rate was ∼1 ×10−4 mm3·N−1·m−1), the copper/graphite composites prepared in this work shown improved wear resistance. Among them, the lowest wear rate (1.942 × 10−5 mm3·N−1·m−1) was obtained at a sintering temperature of 900 °C, with a relative density of 98.41%, a hardness of 75.67 HV and an average coefficient of friction of 0.15. This will help to further broaden the application areas of copper/graphite composites.

materials science, multidisciplinary
The Excellent Anti-Wear and Friction-Reducing Performance of Magnesium Silicate Hydroxide/graphite Nanocomposite (MSH-C) As a Lubricant Additive

Kai Wang,Qiuying Chang,Kai Gao,Bin Wang,Rongqin Gao,Qingqing Yan

DOI: https://doi.org/10.1115/1.4066304

2024-01-01

Journal of Tribology

Abstract:In this paper, MSH-C and MSH-GO composites were prepared by doping MSH with micron-sized few-layer graphene oxide (∼10 um) and nanoscale graphite (∼300 nm), respectively, during the hydrothermal synthesis process. Octadecyltrimethoxysilane (ODTMS) was used as a surfactant to disperse these two types of additives into the fully formulated oil. Tribological tests demonstrated that MSH-C exhibits much more superior tribological properties when compared to MSH-GO. The findings reveal that the oil sample containing 0.5 wt% MSH-C can effectively reduce wear volume (by approximately 26.4%) as compared to fully formulated oil and that the friction coefficient is decreased to ∼0.02. SEM, Raman, FIB-TEM, and TOF-SIMS characterizations and molecular dynamics simulation were used to investigate the tribological mechanism. A tribo-film composed of two layers of different compositions was formed on the worn surface of MSH-C, indicating the synergistic effect of MSH and graphite.
Microstructure, mechanical properties and wear behavior of Mg matrix composites reinforced with Ti and nano SiC particles

Hossein Ahmadian,Tianfeng Zhou,A. Alansari,A. Senthil Kumar,A. Fathy,M. Elmahdy,Qian Yu,Guo Weijia

DOI: https://doi.org/10.1016/j.jmrt.2024.07.125

IF: 6.267

2024-07-26

Journal of Materials Research and Technology

Abstract:This study examines the mechanical properties and wear mechanisms of magnesium (Mg) metal matrix composites reinforced with titanium (Ti) and silicon carbide (SiC) particles. Three different composite formulations were investigated: Mg-30 wt% Ti (A), Mg-25 wt% Ti-5 wt.% SiC (NB), Mg-20 wt% Ti-10 wt% SiC (NC), and Mg-15 wt% Ti-15 wt% SiC (ND). These composites were fabricated through ball milling and spark plasma sintering (SPS). The incorporation of SiC particles significantly enhanced grain refinement and phase formation within the composites. Density analysis revealed that the actual densities of the composites were lower than the theoretical values, with Composite A exhibiting the highest actual density of 2.15 g/cm3 and the lowest porosity of 16.31%. The introduction of SiC particles increased porosity, with Composite NB displaying the highest porosity at 30.58%. Hardness testing indicated that Composite NC, containing 10 wt% SiC, achieved the highest hardness of 137 HV. In contrast, Composite ND, with 15 wt% SiC, showed a reduced hardness of 115 HV, attributed to increased porosity and potential SiC particle agglomeration. Wear behavior was evaluated using a pin-on-disc tribometer. Weight loss measurements indicated that Composite A had the lowest weight loss (1.1–2.1 mg), while Composite NB experienced the highest weight loss (2.8–8.3 mg) due to increased porosity. Composite NC demonstrated a balance with moderate weight loss (2.0–3.8 mg). The coefficient of friction (COF) varied with SiC content and applied loads (2, 4, and 8 N), with Composite A demonstrating the lowest COF values (2.3–2.8) and stable performance across different loads. Composite NB exhibited higher COF values (3.5–4) and significant fluctuations due to elevated porosity and the presence of SiC particles. Composite NC showed better wear resistance and more stable COF values (2.5–2.9) compared to NB and ND.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Mechanical and Tribological Behaviors of Hot-Pressed SiC/SiCw-Y2O3 Ceramics with Different Y2O3 Contents

Shaohua Zhang,Jinfang Wang,Meng Zhang,Longqi Ding,Huijun Chan,Xiyu Liu,Fengqing Wu,Zhibiao Tu,Ling Shao,Nengyong Ye,Sheng Dai,Liu Zhu,Shichang Chen

DOI: https://doi.org/10.3390/coatings13050956

IF: 3.236

2023-05-20

Coatings

Abstract:Sintering additives are commonly used to reduce the conditions required for densification in composite ceramics without compromising their performances simultaneously. Herein, SiC/SiCw-Y2O3 composite ceramics with 10 vol.% SiC whiskers (SiCw) and different Y2O3 contents (0, 2.5, 5, 7.5, and 10 vol.%) were fabricated by hot-pressed sintering at 1800 °C, and the effects of Y2O3 content on the microstructure, mechanical properties, and tribological behaviors were investigated. It was found that the increased Y2O3 content can promote the densification of SiC/SiCw-Y2O3 composite ceramics, as evidenced by compact microstructure and increased relative density. The Vickers hardness, fracture toughness, and flexural strength also increased when Y2O3 content increased from 2.5 vol.% to 7.5 vol.%. However, excessive Y2O3 (10 vol.%) aggregated around SiC and SiCw weakens its positive effect. Furthermore, the Y2O3 additive also reduces the coefficient of friction (COF) of SiC/SiCw-Y2O3 composite ceramics, the higher the Y2O3 content, the lower the COF. The wear resistance of SiC/SiCw-Y2O3 composite ceramics is strongly affected by their microstructure and mechanical properties, and as-sintered SiC ceramic with 7.5 vol.% Y2O3 (Y075) shows the optimal wear resistance. The relative density, Vickers hardness, fracture toughness, and flexural strength of Y075 are 97.0%, 21.6 GPa, 7.7 MPa · m1/2, and 573.2 MPa, respectively, the specific wear rate of Y075 is 11.8% of that for its competitor with 2.5 vol.% Y2O3.

materials science, multidisciplinary,physics, applied, coatings & films
Interface enhancement of carbon nanotube/mesocarbon microbead isotropic composites

Shen Ke,Zhang Qiang,Huang Zheng-Hong,Yang Junhe,Yang Guangzhi,Shen Wanci,Kang Feiyu

DOI: https://doi.org/10.1016/j.compositesa.2013.09.008

2014-01-01

Abstract:Carbon nanotubes (CNTs) are incorporated into mesocarbon microbead (MCMB)-derived isotropic graphite to improve their mechanical properties. CNTs are homogenously distributed on the MCMB surface by acid-treatment and mechanical mixing. The composites are prepared by cold isostatic pressing, carbonization, and graphitization. The mechanical properties and isotropy ratios of the CNT/MCMB composites are determined by four-point bend tests and thermal expansion measurements, respectively. The addition of CNTs improves the flexural strength by ca. 20%, while keeps a low isotropy ratio. CNTs dispersed on particle interfaces improve the interfacial strength, this reinforcing mechanism is confirmed by a fracture mode analysis with scanning electron microscope.
Effect of the amount of SiC particles on the microstructure, mechanical and wear properties of FeMnCoCr high entropy alloy composites

Yan-ling Gu,Meng-ling Yi,Yang Chen,Jian Tu,Zhi-ming Zhou,Jin-ru Luo

DOI: https://doi.org/10.1016/j.matchar.2022.112300

IF: 4.537

2022-11-01

Materials Characterization

Abstract:Ceramic particle reinforced high entropy (HEA) alloy composites have attracted considerable attention due to their excellent combination of strength, ductility, and wear resistance. In this work, the high entropy alloy composites (Fe50Mn30Co10Cr10 matrix) with the different SiC contents (0.1, 0.5, 1, and 3 vol%) were fabricated by arc melting. The effect of SiC content on microstructure characteristics, mechanical and wear properties of Fe50Mn30Co10Cr10 composites were studied. The results showed that SiC stabilized the γ phase and refined the grain sizes. In addition, the number of ε variants were decreased with refined grain sizes. The composite with 1 vol% SiC optimized the combination of ultimate tensile strength and ductility, which is attributed to grain-boundary strengthening, twin boundary strengthening, dispersion strengthening and load-bearing strengthening. Simultaneously, the optimized composite with 1 vol% SiC displayed the best wear friction ability, in which the proper SiC content played a key role in carrying load during friction.

materials science, multidisciplinary,metallurgy & metallurgical engineering, characterization & testing
Nano-Magnesium Silicate Hydroxide/Crumpled Graphene Balls Composites, a Novel Kind of Lubricating Additive with High Performance for Friction and Wear Reduction

Tong Zhang,Jianguo Zhao,Jin Zhang,Shanshan Zhang,Jingwei Li,Shijie Li,Xinyu Li,Jie Zhang

DOI: https://doi.org/10.3390/ma13173669

IF: 3.4

2020-08-19

Materials

Abstract:In this study, crumpled graphene balls (CGB), a kind of nano-material, was used as an additive to improve the tribological properties of base oil. Nano-magnesium silicate hydroxide (MSH)/CGB composites were prepared by ultrasound-assisted liquid-phase exfoliation. The loading of MSH significantly increased the number of pleats and reduced the lamellar thickness of CGB. Then, in order to improve the compatibility with the base oil, the MSH/CGB composites were decorated with oleic acid and stearic acid to get modified lipophilic composites (ML-MSH/CGB). The ML-MSH/CGB were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM). In addition, the tribological properties of the ML-MSH/CGB in base oils were investigated using a ball-on-disc setup tribometer. It indicated that the fantastic tribological behavior of the ML-MSH/CGB in base oil may contribute to a smaller and extremely wrinkled laminated structure. Furthermore, the base oil with 0.005 wt% ML-MSH/CGB composites exhibited the best anti-friction effect, and its average friction coefficient, wearing capacity and wear scar diameter were reduced by 25.4%, 22.1% and 16.7%, respectively. The introduction of ML-MSH/CGB composed materials is an excellent strategy to optimize the friction performance of lubricating oil.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Influence of structure parameters on the tribological properties of MoB/Cu laminated composites

Haisheng Li,Yefei Li,Qiaoling Zheng,Huicong Zhao,Dawei Yi,Yihui Wang,Peipei He,Yanan Chen

DOI: https://doi.org/10.1016/j.wear.2024.205549

IF: 4.695

2024-08-19

Wear

Abstract:Strong-bonding MoB/Cu laminated(MCL) composites are fabricated by the hot-press method at 1030 °C for 1 h under 20 MPa pressure. In this study, the microstructure, tribological properties, and elemental microanalysis are systematically investigated. The structure parameters of laminated composites play a key role in the properties of friction and wear resistance. The average friction coefficient is below 0.3 and the wear rate is almost one order of magnitude lower when the measured ratio of copper thickness to MoB thickness is below 4, compared with the sample whose λ equals 13. The primary phases of MCL are Al 2 O 3 , Cu(Al), and MoB. They helped the lubricating film to form on the worn surface during the wear process. These tribo-films effectively moderate the wear while safeguarding the metal matrix.

engineering, mechanical,materials science, multidisciplinary
Homogenous and Highly Isotropic Graphite Produced from Mesocarbon Microbeads

Ke Shen,Zheng-Hong Huang,Wanci Shen,Junhe Yang,Guangzhi Yang,Suyuan Yu,Feiyu Kang

DOI: https://doi.org/10.1016/j.carbon.2015.06.034

IF: 10.9

2015-01-01

Carbon

Abstract:Mesocarbon microbeads (MCMBs) are attractive precursors for high-density, high-strength polycrystalline graphite due to their self-sintering capability. They have the shape of a standard sphere and stack in a completely random orientation during compaction, thereby leading to an isotropic texture. In this paper, MCMB-based graphite shows better isotropic property than commercial nuclear graphite, as demonstrated by a coefficient of thermal expansion-based isotropy ratio of 1.00. It was found that variations in apparent density within block are approximately 2–5% in graphitized artifacts. The variation of flexural strength within block is small, revealing excellent homogeneity of MCMB-based graphite. Density distribution measurement indicates that artifacts produced in the same batch also have low variation from block to block. Furthermore, the flexural strength of this material is greatly influenced by heat treatment temperature and mean particle size. The fracture mechanism is also shown by a detail examination of fracture surfaces. These results may help to gain a better understanding of MCMB-based graphite.
High-pressure synthesis and performance analysis of WC-cBN-MoS2 self-lubricating ceramic composites

Jiakun Wu,Haikuo Wang,Zhicai Zhang,Chao Wang,Zhiqiang Hou,Shun Wan,Dazhuan Wu,Xiaoping Ouyang

DOI: https://doi.org/10.1016/j.ijrmhm.2022.105989

IF: 4.804

2023-01-01

International Journal of Refractory Metals and Hard Materials

Abstract:WC-cBN-MoS2 self-lubricating ceramics were synthesized by using high pressure and high temperature sintering method. An analytical model of the self-lubricating properties has been developed to reveal the interrelationship between mechanical and self-lubricating properties. The influence of mechanical and self-lubricating properties of ceramics on the wear rate were analyzed. Self-lubricating performance optimization criterion are proposed accordingly. It was found that MoC, WS2 can be formed during sintering, which can ensure self-lubricating and low temperature sintering properties. Adhesive wear is the main wear mechanism, the extent of which varies with the content of self-lubricating components. The high modulus of elasticity is the main reason for the excellent self-lubricating and mechanical properties of composites. The well-sintered WC-cBN-MoS2 bulks present an excellent self-lubricating property with a hardness of 26.3 GPa and fracture toughness of 10.5 MPa·m1/2, which is improved at least by 52% and 46% respectively compared with the traditional self-lubricating ceramics.

materials science, multidisciplinary,metallurgy & metallurgical engineering
WEAR PROPERTIES OF ALUMINUM MATRIX COMPOSITES REINFORCED BY GRAPHENE ENCAPSULATED SiC NANOPARTICLES

S. GUO,J. B. GAO,X. M. DU,G. S. FANG,H. T. QI,N. LI,G. ZHANG,,,,,,,

DOI: https://doi.org/10.15251/djnb.2021.161.249

2021-01-01

Digest Journal of Nanomaterials and Biostructures

Abstract:Graphene encapsulated SiC nanoparticles reinforced aluminum matrix composites were prepared by high energy ball-milling and hot-press sintering methods. The effect of graphene content on microstructure and wear properties of composites was investigated. The results show that the graphene sheets successfully encapsulates SiC nanoparticles to form a composite reinforcement phase under the condition of the graphene content of 1 wt.%. SiC nanoparticles encapsulated with graphene predominantly are homogeneously distributed on the grain boundaries of Al matrix. The interface between graphene and Al matrix is sharpand no Al-C compound is formed on the interface. The increase of the reinforcement phase reduces the wear performance of the composite material. The main wear mechanisms of aluminum-based composite materials are the combination of delamination wear and abrasive wear. As the graphene content increases, the wear mechanism changes from abrasive wear to delamination wear.

materials science, multidisciplinary,nanoscience & nanotechnology
Study on the tribological properties of MoB/Cu laminated composite materials fabricated by hot-pressing process

Haisheng Li,Yefei Li,Qiaoling Zheng,Huicong Zhao,Yiran Wang,Su Zhang,Zhiyun Zhang,Pengjun Yang,Yimin Gao

DOI: https://doi.org/10.1016/j.matlet.2024.136500

IF: 3

2024-04-22

Materials Letters

Abstract:This work presents a novel method for fabricating MoB/Cu laminated composite materials which are distinguished by their strong interlayer bonding and unique microstructure. MoB ceramic layer can obviously improve the friction and wear properties of Cu matrix composites. The tribological properties on cross-sections of MoB/Cu laminated composite are studied with GCr15 (a typical high-carbon chromium bearing steel) ball as counterpart under dry friction conditions. When the friction angle is less than 30°, the wear rate (∼0.4974 × 10 -4 mm 3 /(N·m)) is reduced substantially by about 85 % compared to pure copper. The coefficient of friction of the composite ranges from 0.182 to 0.223 at a friction angle from 0° to 90°. A dense lubricating oxide film is formed during the friction process, effectively slowing down the adhesive wear and increasing the friction and wear resistance. After XPS (X-ray photoelectron spectroscopy) analysis, the main components of the lubricating film generated during the friction process are MoO 3 , B 2 O 3 , Al 2 O 3 , CuO, and Fe 2 O 3 .

materials science, multidisciplinary,physics, applied

Latinos on Race and Ethnicity : Alcoff , Corlett , and Gracia

Study on interface modification and tribological properties of MCMB-SiC self-lubricating composites

A Study of Tribological Performance and Tribo-Induced Graphitization of Meso-Carbon Microbeads

Tribological properties of reaction-formed graphite/SiC composites under water-lubricated conditions

Enhancement of Tribological Properties in Siliconized Graphite Via Hierarchically Hybrid SiC/C Composite

Fabrication and mechanical properties of in situ prepared mesocarbon microbead/carbon nanotube composites

Effect of Oxidative Stabilization on the Sintering of Mesocarbon Microbeads and A Study of Their Carbonization

Effect of Carbon in Fabrication Al-SiC Nanocomposites for Tribological Application

Microstructure, mechanical and tribological properties of multilayer grapheme reinforced WC-10Ni 3 Al prepared by microwave sintering

Effect of sintering temperature on microstructure and tribological properties of copper/graphite composites doped with Ti3AlC2 particles

The Excellent Anti-Wear and Friction-Reducing Performance of Magnesium Silicate Hydroxide/graphite Nanocomposite (MSH-C) As a Lubricant Additive

Microstructure, mechanical properties and wear behavior of Mg matrix composites reinforced with Ti and nano SiC particles

Mechanical and Tribological Behaviors of Hot-Pressed SiC/SiCw-Y2O3 Ceramics with Different Y2O3 Contents

Interface enhancement of carbon nanotube/mesocarbon microbead isotropic composites

Effect of the amount of SiC particles on the microstructure, mechanical and wear properties of FeMnCoCr high entropy alloy composites

Nano-Magnesium Silicate Hydroxide/Crumpled Graphene Balls Composites, a Novel Kind of Lubricating Additive with High Performance for Friction and Wear Reduction

Influence of structure parameters on the tribological properties of MoB/Cu laminated composites

Homogenous and Highly Isotropic Graphite Produced from Mesocarbon Microbeads

High-pressure synthesis and performance analysis of WC-cBN-MoS2 self-lubricating ceramic composites

WEAR PROPERTIES OF ALUMINUM MATRIX COMPOSITES REINFORCED BY GRAPHENE ENCAPSULATED SiC NANOPARTICLES

Study on the tribological properties of MoB/Cu laminated composite materials fabricated by hot-pressing process