Abstract:Plasticized poly(lactic acid) (PLA)/poly(butylene succinate) (PBS) blend-based films containing chitin nanofibrils (CN) and calcium carbonate were prepared by extrusion and compression molding. On the basis of previous studies, processability was controlled by the use of a few percent of a commercial acrylic copolymer acting as melt strength enhancer and calcium carbonate. Furthermore, acetyl n-tributyl citrate (ATBC), a renewable and biodegradable plasticizer (notoriously adopted in PLA based products) was added to facilitate not only the processability but also to increase the mechanical flexibility and toughness. However, during the storage of these films, a partial loss of plasticizer was observed. The consequence of this is not only correlated to the change of the mechanical properties making the films more rigid but also to the crystallization and development of surficial oiliness. The effect of the addition of calcium carbonate (nanometric and micrometric) and natural nanofibers (chitin nanofibrils) to reduce/control the plasticizer migration was investigated. The prediction of plasticizer migration from the films’ core to the external surface was carried out and the diffusion coefficients, obtained by regression of the experimental migration data plotted as the square root of time, were evaluated for different blends compositions. The results of the diffusion coefficients, obtained thanks to migration tests, showed that the CN can slow the plasticizer migration. However, the best result was achieved with micrometric calcium carbonate while nanometric calcium carbonate results were less effective due to favoring of some bio polyesters’ chain scission. The use of both micrometric calcium carbonate and CN was counterproductive due to the agglomeration phenomena that were observed.

Constrained amorphous interphase in plasticized poly(lactic acid): Composition and tensile elastic modulus estimation

Influence of moulding processing on poly (lactic acid) (PLA) semi-crystalline properties

Role of the plasticizers on the crystallization of PLA and its composites with mesoporous MCM-41

The mesophase of PLA in binary materials with ATBC and in composites with ATBC and mesoporous MCM-41

Improved Impact Properties in Poly(lactic acid) (PLA) Blends Containing Cellulose Acetate (CA) Prepared by Reactive Extrusion

Dependence of the crystal structure on the d-units amount in semi-crystalline poly(lactic acid)

Mechanical Properties and Non-Isothermal Crystallization Kinetics of Polylactic Acid Modified by Polyacrylic Elastomers and Cellulose Nanocrystals

Effect of Plasticization/Annealing on Thermal, Dynamic Mechanical, and Rheological Properties of Poly(Lactic Acid)

Quantitative Nanomechanical Investigation on Deformation of Poly(lactic acid)

Thermal and Mechanical Properties of Polylactide Toughened with A Butyl Acrylate-Ethyl Acrylate-Glycidyl Methacrylate Copolymer

Stretch-induced crystalline structural evolution and cavitation of poly(butylene adipate-ran-butylene terephthalate)/poly(lactic acid) immiscible blends

Mechanical properties of 3D printed polylactic acid elements: Experimental and numerical insights

Crystal polymorphism of polylactide and its composites by X-ray diffraction study

Sustainable Micro and Nano Additives for Controlling the Migration of a Biobased Plasticizer from PLA-Based Flexible Films

The Influence of Epoxy Functionalized Acrylate Particles on the Properties of Plasticized Pla Blown Films

Structure and Property of Epoxy-Functionalized Acrylic Rubber Toughened Polylactide

Mechanical properties of CF-reinforced PLA parts manufactured by fused deposition modeling

Investigating the large strain compression properties of PLA parts manufactured by FDM using experiments and constitutive modeling

Synthesis of novel L-lactic acid-based plasticizers and their effects on the flexibility, crystallinity, and optical transparency of poly(lactic acid)

Tuning the mechanical and thermomechanical properties through the combined effect of crosslinking and annealing in poly(lactic acid)/acrylonitrile‐EPDM‐styrene blends

Toughening of polylactide with epoxy-functionalized methyl methacrylate–butyl acrylate copolymer