[Maxillary sinusitis].

M. Takayama,M. Tomita

Abstract:

What problem does this paper attempt to address?

Nonlinear Finite-Element Analysis of the Seismic Behavior of RC Column–Steel Beam Connections with Shear Failure Mode

Yuchen Tao,Weijian Zhao,Jiangpeng Shu,Yuanzhang Yang

DOI: https://doi.org/10.1061/(asce)st.1943-541x.0003132

2021-01-01

Journal of Structural Engineering

Abstract:RC column-steel beam (RCS) systems, a novel type of hybrid structure, have been used widely in recent decades owing to their excellent seismic performance and simple fabrication process. However, due to the effects of variable strengthening configurations on force-transfer mechanisms, the mechanical behavior of RCS connections has not been fully understood by existing experimental studies. This paper proposes a reliable finite-element model of RCS connections and investigated the effects of different strengthening configurations and design parameters on the seismic performance and shear mechanism. A detailed three-dimensional finite-element model was developed and validated against previously obtained experimental results, including load-displacement relationships and cracking patterns. Parametric studies based on the validated model were conducted. The studies showed that the axial load ratio significantly affects the failure mode and ductility of the connection. The load-carrying capacity of the connection is enhanced significantly when the concrete strength is increased. Furthermore, additional yield capacity of steel plates and transverse reinforcements has limited effects on crack propagation and strain state when adequate resistance can be provided.
Experimental study and numerical simulation of seismic performance of stiffened thin steel plate shear walls considering the effect of vertical load on frame column

FU Bo,HONG Qi,JING Ting,SUN Hao,TONG Gen-shu

DOI: https://doi.org/10.6052/j.issn.1000-4750.2022.02.0146

2023-01-01

Abstract:An experimental research was conducted on seismic behavior of stiffened thin steel plate shear walls (SPSWs) considering the effect of vertical load on frame column. Two full-scale rectangular concrete-filled steel tube columns-stiffened thin steel plate shear specimens were tested under low-cycle reverse load. The design of specimens considers two cases of vertical stiffeners with equal spacing and variable spacing. The test results show that the specimens have good ductility and energy consumption capacity when the frame columns are subjected to high axial pressure. The ultimate drift angle of the specimens reaches 1/30. The plastic deformation of the specimens is mainly manifested as the out-of-plane buckling, which satisfies the design concept of “strong column and weak beam”. The arrangement of the stiffeners has no obvious influence on the seismic performance of the specimens. The nonlinear finite element method is further used to study the influence of initial defects and axial compression ratio on the lateral resistance performance of the specimen. The analysis results show that the initial defect distribution mode of the wall and the out-of-plane deflection amplitude have little effect on the pushover curve of the specimens. When the axial compression ratio of the frame column is greater than 0.7, the bearing capacity and deformation capacity of the specimens are reduced. Based on the shear control failure characteristics of the specimens, the calculation method of the specimen’s shear capacity is given. The calculated value is in good agreement with the finite element simulation value, and it is conservative than the experimental value.
Experimental Investigation on Performance of Cantilever CFRP-wrapped Circular RC Columns under Lateral Low-Velocity Impact

Dade Lai,Cristoforo Demartino,Jinjun Xu,Jing Xu,Yan Xiao

DOI: https://doi.org/10.1016/j.compstruct.2020.112143

IF: 6.3

2020-01-01

Composite Structures

Abstract:The main goal of this study is to investigate the effectiveness of seismic retrofit using CFRP wrapping in reducing the damage and preventing the failure of RC bridge piers under vehicular impacts. This paper reports the results of an experimental investigation on the performance of cantilever CFRP-wrapped circular RC columns under lateral low-velocity impact. To this aim, a total of nine 1/3-scale cantilever columns without axial load, comprising three types of shear-deficient RC columns with different reinforcement layout, were tested in a horizontal collision facility at two different impact velocities. The columns were tested in plain configuration (0 plies) and two wrapped configurations with 2 and 4 plies of CFRP. Generally, for plain columns, brittle shear-type damage was observed. Larger damage was obtained by increasing the impact velocity and decreasing the amount of transverse reinforcements while the variation of the amount of longitudinal steel bars has a negligible effect. The experimental results demonstrate that seismic retrofit using CFRP can provide an effective solution to convert the failure mechanism under lateral impact loading, from shear- to flexural-dominated, with a reduction of the impact damage. This strategy has a beneficial effect given sufficient bending capacity of the plain RC column.
EXPERIMENTAL STUDY ON THE SEISMIC BEHAVIOR OF CFST RECTANGULAR COLUMN TO H-SECTION STEEL BEAM CONNECTIONS WITH EXTERNAL STIFFENERS

FU Bo,WANG Yan-chao,TONG Gen-shu

DOI: https://doi.org/10.6052/j.issn.1000-4750.2019.08.0474

2020-01-01

Abstract:In view of the decreasing trend of column widths in steel residential buildings, a new type of concrete filled rectangular steel tubular column-H-section steel beam connections with external stiffeners is proposed. The diaphragm is removed in this connection. Pseudo-static tests of seven new joint specimens were carried out. The test parameters were the section of the steel beam and the thickness and the height of the long side of the external stiffeners. The failure modes, hysteretic curves, skeleton curves, strength, stiffness degradation, strength degradation, ductility and energy dissipation capacity of the joints were studied. The test results show that there were three failure modes of this new joint, namely, tensile failure of beam flange, weld failure between beam flange and external stiffener, and column wall failure near the external stiffener. The ductility coefficient was 2.17 to 3.67, the equivalent viscous damping coefficient was 0.2 to 0.3, and the average drift ratio was 1/49. The seismic performance of the joint met the requirements of strong joints and weak members. Increasing the thickness or the height of the long side of the external stiffeners can increase the strengths of the joints. The premature cracking of the beam flange, the welding seam between beam flange and external stiffener, or the column wall will reduce the ductility and energy dissipation capacity of the joints. It is proposed that the connection coefficient should be 1.4 when checking the ultimate strength of the column wall and joint weld. The strengthening or weakening measures on the flange at the beam ends can be taken to ensure that the new joints have a sufficient plastic deformation capacity.
Seismic-design-oriented Classification of Structures and Members and Structure Influence Coefficient

TONG Gen-shu

DOI: https://doi.org/10.3321/j.issn:1673-2049.2007.03.013

2007-01-01

Abstract:Based on the analysis of ductility,damping,post-yield stiffness,energy-dissipating capacity,hysteretic curve shape,effecting on SDOF system under seismic,a systematic classification of earthquake-resistant structures,members,sections and structure influence coefficient closely related to the classification were proposed.For coordinating to concept of minor shock seismic force,and considering good ductility of steel structure,much cutting to seismic action,seismic ductility adjustment coefficient was introduced and supported to classification of structures and members.
Displacement-based Seismic Design Method for Square CFT Columns

Xiaoyong Mao,Yan Xiao

DOI: https://doi.org/10.3969/j.issn.1007-6069.2007.04.007

2007-01-01

Abstract:Displacement-based seismic design method of concrete filled square tubular columns has been researched in this paper. The key problems such as equivalent stiffness and damping ratio, the detail design procedure of CFT columns and the main factors related with CET columns are summarized. Results show that stiffness of the second stage has little effect to hysteretic damping ratio.The thickness of steel tube and the displacement ductility of the CFT columns are both increased as increasing axial loading ratio, the thickness of steel tube and yield moment are both decreased as increasing the section dimension of the CFT columns.
Analysis on design parameters of seismic performance based on damage for recycled aggregate concrete-filled steel tube column

Xianggang Zhang,Dapeng Deng,Jianhui Yang

DOI: https://doi.org/10.1108/ijsi-04-2019-0029

2019-09-12

International Journal of Structural Integrity

Abstract:Purpose The purpose of this paper is to establish the horizontal displacement angle limit values under different performance level, use damage as the quantitative index of performance level and determine the design principle of the RACFST column for performance-based seismic fortification target based on the damage. Design/methodology/approach The paper is based on the seismic performance test of the RACFST column. Findings First, three-level seismic are introduced into the performance design foundation of the RACFST column. Second, the performance level of the RACFST column is divided into five grades: normal use, temporary use, use after repair, life safety and prevention of collapse. Third, the seismic performance targets of RACFST columns are divided into four categories: unacceptable situation, basic performance target, important performance target and special performance target. Originality/value The initial damage of the recycled aggregate occurs in the process of crushing and screening, and the damage evolution and development of the RACFST column occur under cyclic load. This is one of the problems that should not be avoided in the design of the seismic performance of the RACFST column. New levels are introduced in the performance design foundation of the RACFST column.
Seismic performance design of energy-dissipated structure system based on damage control and time-varying damping ratio

Wang Bao-shun,Hao-xiang He,Yan Wei-ming

DOI: https://doi.org/10.1016/j.soildyn.2021.106996

IF: 4

2021-12-01

Soil Dynamics and Earthquake Engineering

Abstract:The installation of energy dissipation devices on building structures can significantly reduce seismic damage. A brief review of first, second and third generation performance-based seismic design (PBSD) theories, and a comparative analysis of existing PBSD methods for energy-dissipated structure systems confirms that design methods based on force, displacement, and energy are inadequate. A more comprehensive approach is the damage-based design method, which can evaluate the seismic performance of structures. However, due to the lack of an analytical relationship between the additional equivalent damping ratio (AEDR) of dampers and the damage degree of the main structure, the current performance design method can only predict the expected damage via an iterative adjustment analysis of damper's design parameters. The authors addressed this problem by analyzing the damage mechanism of the energy-dissipated structure system's core area from the perspective of energy dissipation. It is established an analytical relationship between the AEDR and the damage index of the main structure with dampers via a damage model based on the energy difference ratio and the time-varying AEDR calculation of dampers subjected to ground motions. With this new approach to seismic vulnerability analysis, the performance design flow of the seismic structure system is based on damage control. A case study verifies the accuracy of the damage-degree based AEDR calculation. The proposed damage-based method effectively controls the damage degree of the main structure to the expected damage target. This method is compatible with the displacement-based design method, and which also enriches the research contents of structural seismic design and damage analysis in the third generation PBSD.

geosciences, multidisciplinary,engineering, geological
Design theory of earthquake-resilient prefabricated column foot joint with lateral force-resisting energy-consuming device

Zi-Qin Jiang,Xiao-Feng Yang,Ai-Lin Zhang,Xing-Shang Hua,Xin Chen

DOI: https://doi.org/10.1016/j.jcsr.2022.107439

IF: 4.349

2022-11-01

Journal of Constructional Steel Research

Abstract:Based on the design concepts of damage control and concentrated energy consumption of key energy-consuming components, this paper puts forward an earthquake-resilient prefabricated column foot joint. Expounds the structural composition, advantages and seismic design requirements of this new type column foot joint in detail. After comprehensively considering the mechanical mechanism of the column foot joint, the load-bearing capacity correction coefficient and the height ratio of lateral force-resisting shear member (LRSM) inflection point are introduced, and the design theory is established accordingly, including the dimension of LRSMs, the number of connecting bolts and the stiffness of connecting beams. The rationality and applicability of the proposed design theory are verified by 18 groups of 90 finite element models, and several test specimens. The research shows that the design theory proposed in this paper can accurately predict the yield load and initial stiffness of the new type column foot joint, and effectively control the bolt slip time and the connecting beam failure time. The new column foot joint designed according to this design theory has excellent bearing capacity and ductility. The plastic damage of this joint can be basically controlled on the lateral force-resisting energy-consuming device (LRECD), which has the premise of earthquake-resilient.

construction & building technology,engineering, civil
Seismic behaviour of pre-damaged RC columns strengthened with CFRP grid/sprayed ECC jackets subjected to horizontal reversed cyclic loading and constant axial force

Xiao-bo Cao,Wen-wei Wang,Xiao Tan,Ya-fei Zhang

DOI: https://doi.org/10.1016/j.cscm.2024.e02948

IF: 4.934

2024-07-01

Case Studies in Construction Materials

Abstract:A new seismic repair method for reinforced concrete columns, which uses carbon fiber reinforced polymer (CFRP) grids and sprayed engineered cementitious composite (ECC) to form a composite reinforcement jacket, was proposed to improve the seismic performance of concrete columns damaged by earthquakes. Five specimen columns with 250 mm × 250 mm cross section and 1160 mm height were prepared and four different damage degree (no-damage, minor damage, moderate damage and severe damage) was controlled by the comparative specimen under the same amplitude-increasing lateral loading protocol and constant axial load. The pre-damaged columns were repaired and strengthened with three layers of CFRP grids and 25 mm thickness of sprayed ECC. The repaired columns were tested to failure and the effectiveness of the repairing schemes was evaluated by comparing load-carrying capacities, ductility, and energy dissipation. Based on the OpenSees seismic analysis software, a finite element model has been proposed to predict the seismic performance of the strengthened columns. The experimental results showed that the yield load, peak load, and ultimate load of the strengthened RC columns with no damage and slightly damage have significantly increased compared to the control specimen, with an increase range of 15% to 18%. For moderately damaged and severely damaged strengthened columns, the increase in the three characteristic load values is very small, or even reduced. Except for the severely damaged strengthened column, the ductility and energy consumption of other specimens have been improved to varying degrees. The analysis results indicated that the simulated values are in good agreement with the experimental ones, and the established finite element analysis model can be used to predict the seismic performance of strengthened columns.

construction & building technology,materials science, multidisciplinary,engineering, civil
Seismic Design Methodology Based on Damage Mechanism Control for Reinforced Concrete Structures

曲哲,叶列平

DOI: https://doi.org/10.14006/j.jzjgxb.2011.10.003

2011-01-01

Abstract:Damage mechanism control is an effective way of enhancing the seismic performance of building structures,where system design,demand analysis and member design are the three essential aspects.A brief review of the development history of seismic structural systems in the sense of damage mechanism control is followed by the proposal of a damage mechanism control-based seismic design methodology which incorporates a two-phase design procedure.In the first phase,linear elastic analysis is used to determine the strength demand for potentially inelastic members.And in the second phase,equivalent linear analysis is used to quantitatively determine the deformability demands for potentially inelastic members and strength demands for other members in order to achieve the desirable damage mechanism.These demands form the basis for the proportioning and section design of each structural member.An example of reinforced concrete ductile moment-resisting frame is provided to demonstrate the implementation of the proposed design method.Nonlinear dynamic analysis is conducted to evaluate its effectiveness.Results show that the proposed method can better ensure the desirable damage mechanism.
Seismic vulnerability of prefabricated reinforced concrete frame structure based on local outsource steel tube bolted column–column connection

Jiaolei Zhang,Jin Li,Qi Liang,Shufeng Li,Dawei Yuan

DOI: https://doi.org/10.1177/1369433220968453

2020-11-03

Advances in Structural Engineering

Abstract:In this paper, the seismic performance of a prefabricated frame structure with a local outsource steel tube bolted column–column connect is evaluated from the perspective of seismic vulnerability theory. Firstly, a simplified model of the prefabricated frame structure was constructed and validated by experiments. Then, a six-story prefabricated reinforced concrete frame structure (PRCS) and a cast-in-situ reinforced concrete frame structure (CRCS) were designed as examples to get the increment dynamic analysis (IDA) of the structure under 12 ground motions, and the two-parameter damage model was used as the structural requirement index. As a traditional structural requirement index-the maximum inter-storey drift angle cannot accurately describe the mechanism of structural damage. Therefore, two types of damage models are compared and analyzed. In addition, in order to evaluate the damage of frame structure effectively, a new damage index weighted combination method is proposed, and its feasibility is verified. Finally, the IDA curve and vulnerability curve with Kunnath two-parameter damage model and the maximum inter-story displacement angle as the requirement index are drawn. The results show that the two-parameter damage model is more accurate than the maximum inter-storey drift angle model in evaluating the seismic performance of the PRCS and CRCS. It shows that the maximum inter-story displacement angle model can overestimate the collapse resistance of the PRCS by 60.7% on average, and the collapse resistance of the CRCS by 75.67% on average. The seismic performance of the CRCS is better than that of the PRCS as the seismic intensity increases. Although the seismic performance of fabricated columns is similar to that of cast-in-place columns, there is still a certain gap in the seismic performance of frame structures.

construction & building technology,engineering, civil
Seismic performance evaluation of a novel resilient steel frame with self-centering rocking columns and replaceable energy-dissipating connections for low-rise structures

Jiawang Liu,Canxing Qiu,Xiuli Du,Hang Liu

DOI: https://doi.org/10.1016/j.engstruct.2024.117580

IF: 5.582

2024-02-05

Engineering Structures

Abstract:To promote the seismic resilience of structures, minimizing both seismic damage and repair time is an effective way. Toward this goal, this paper proposes a novel resilient steel frame (RSF). The kernel structural components are the self-centering (SC) rocking columns and the replaceable energy-dissipating (ED) connections. The SC rocking columns equipped with shape memory alloy slip friction dampers (SMASFDs) reduce residual deformation and plastic damage of column bases, whereas the ED connections using shaped fuse steel plates mainly dissipate the input seismic energy . To demonstrate the seismic response characteristics, the numerical model of a three-story RSF is developed in OpenSees. The model is firstly validated by experimental results and then its seismic performance evaluations are carried out using three suites of earthquake ground motions associated with three seismic hazard levels. An equivalent conventional steel frame (CSF) with ED connections and rigid column bases is introduced as the counterpart. Incremental dynamic analysis (IDA) is conducted to obtain samples of the demand. Based on the IDA data, the joint fragility curves are generated using the joint probability density functions , taking into account the coupling relationship between the maximum and residual drift. The analysis results show that the RSF exhibits comparable maximum interstory drift and lower residual interstory drift, compared with the CSF. The introduction of the SC rocking column effectively protects the column from yielding and mitigates the residual deformation of the replaceable ED connections, therefore improving the reparability and seismic resilience of the structural system.

engineering, civil
Numerical simulation of seismic behavior of earthquake damaged rc columns strengthened with frp

LI Shuo,ZHAO Zuo-zhou

DOI: https://doi.org/10.6052/j.issn.1000-4750.2022.01.0061

2023-01-01

Abstract:Based on appropriate constitutive models of materials, undamaged and un-strengthened, undamaged but FRP strengthened, and FRP strengthened pre-damaged RC columns are numerically simulated and analyzed by ABAQUS. The reasonable pre-damage simulation method is proposed, and the model change interaction method is adopted to simulate the demolishment and replacement of severely damaged concrete and FRP strengthening. Numerical simulation results are basically consistent with the experimental results. On this basis, the numerical simulation results of three kinds of RC columns are compared. It is found that: the lateral stiffness and bearing capacity of FRP strengthened severely damaged RC columns cannot be fully restored, and the effects of different damage degrees and different FRP strengthening measurements need to be considered. RC columns with different damage degrees and strengthening methods are studied. The results show that the longitudinal and transverse FRP composite reinforcement is effective for the specimens with moderate seismic damage. The repair and replacement of severely damaged peripheral concrete is the key to the performance of FRP strengthened pre-damaged RC columns. Compared with transverse FRP strengthening, the effect of longitudinal and transverse FRP combination reinforcement is better.
Research on design method of end stiffening ribs for square UHPCFHSST columns

Zicheng Yu,Yunfan Li,Juan Zhang,Zhi Luo,Jingkai Qin,Guofeng Du

DOI: https://doi.org/10.1016/j.jcsr.2024.108599

IF: 4.349

2024-03-15

Journal of Constructional Steel Research

Abstract:This study explores the design strategies for end stiffening ribs in square ultra-high-performance concrete-filled high-strength steel tube (UHPCFHSST) columns. It considers the axial compression ratio (0.1, 0.15, 0.2) and stiffener height (360 mm, 483 mm, 965 mm), and performs quasi-static test on 8 square UHPCFHSST columns with end ribs to evaluate their seismic performance. Then, the length, height, width, and number of stiffeners are extended by ABAQUS, enabling a thorough quantitative analysis of their impact on the structure's seismic performance. The equations for calculating the horizontal bearing capacity and displacement ductility of square UHPCFHSST columns were derived from the test results and finite element expansion analysis. The results of test and finite element analysis demonstrated that the specimens exhibited a compression-flexure failure mode, with plastic deformation and cumulative damage primarily concentrated in the web area of the column base. The increase in axial compression ratio enhances energy dissipation ability, but leads to stiffness degradation and reduced ductility. Additionally, the peak loads initially increased and then decreased with increasing axial load. The increase in the height, width, and number of stiffening ribs is proportional to the peak load, accumulated energy dissipation and ductility. As the length of the stiffening ribs increased, peak load, accumulated energy dissipation, and ductility initially increased and then decreased. It was also found that the calculated results of the proposed equation aligned well with the test, ABAQUS, and related literature data. Square UHPCFHSST columns with end stiffening ribs can be a viable option for usage in high seismic intensity areas.

construction & building technology,engineering, civil
Dynamic performance and cross-level damage criteria of strengthened reinforced concrete frames with VE energy dissipation braces

Yao-Rong Dong,Zhao-Dong Xu,Zhen-Hua He,Yeshou Xu,Xing-Huai Huang,Jia-Xuan He,Yang Yang

DOI: https://doi.org/10.1080/15376494.2022.2114047

2022-08-26

Mechanics of Advanced Materials and Structures

Abstract:Based on the low cost and superior damping performance of viscoelastic dampers, the new structural system strengthened with viscoelastic energy dissipation braces (VEDB) is proposed to upgrade the reinforced concrete frame structures with insufficient seismic capability. For the dynamic performance researches and damage evolution predictions of this structure system during earthquakes, the dynamic performance of six RCFs (reinforced concrete frames) and six VEFs (another six special reinforced concrete frames with VEDB) are studied under sinusoidal wide frequency range loading excitation horizontally. On this basis, the qualitative and quantitative relations on the damage growing at the material-level and the member-level performance deteriorating about the frame structures are conducted. Furthermore, the empirical calculation model on the cross-level damage evolution of VEFs are established and verified. Finally, a set of useful and robust cross-level judgment criteria for damage performance rates is proposed. The research found that, the installation of VEDB can significantly improve the load bearing capacity, the lateral stiffness and the energy dissipation capacity of the structures. The damage pattern of the structures is improved by VEDB, and it ensures the design criteria of "strong joints and weak members." The empirical calculation model on the cross-level damage evolution and judgment criteria for damage performance rates proposed in this paper are useful and stable in practical engineering.

materials science, multidisciplinary,mechanics, composites, characterization & testing
Seismic performance and damage properties of flexure–shear critical RC columns with various loading cycles

Qin Zhang,Ming-Hui Chen,Wen-Jie Li,Xiang-Lin Gu,Jin-Xin Gong,Zhang, Qin

DOI: https://doi.org/10.1007/s10518-023-01736-5

IF: 4.556

2023-07-07

Bulletin of Earthquake Engineering

Abstract:An experimental study was conducted to investigate the effects of loading cycles on seismic behaviors and damage properties of flexure–shear critical reinforced concrete columns. Two sets of circular columns (including eight specimens) with different shear span ratios were tested under quasi-static loads with various numbers of loading cycles, namely 0 (i.e., monotonic loading), 3, 10, and 20 cycles. The failure modes, load-deformation curves, ductility, and energy dissipation capacities of the flexure–shear critical columns with various loading cycles were explored. The test results revealed that the flexure–shear failures of columns were more likely to occur with an increase in loading cycles, as evidenced by intensified shear effects and cumulative damage effects induced by cyclic loading. The study examined that the ultimate deformation was the most crucial factor that affects the damage properties of the flexure–shear critical columns. The ultimate displacements diminished with the loading cycles increasing and reduced by 38%, 50%, and 62% when the loading cycles increased from 0 to 3, 10, and 20 cycles, respectively. Additionally, the damage properties of the flexure–shear critical columns were also pertinent to cumulative energy dissipation. The cumulative energy dissipation of the column specimens significantly increased after yielding and rose in proportion to the loading cycles. Two analytical models were proposed for the evaluation of equivalent viscous damping and seismic damage index in flexure–shear columns, which considered the effects of the number of loading cycles. These models could better provide an optimal analysis of the energy dissipation capacities and damage properties for flexure–shear critical columns subjected to seismic excitations, respectively.

geosciences, multidisciplinary,engineering, geological
A Performance-Based Design Approach for Rectangular Concrete-Filled Steel Tube (RCFT) Frames under Seismic Loading

Cenk Tort,Jerome F. Hajjar

DOI: https://doi.org/10.1061/40944(249)57

2007-10-10

Abstract:Performance of buildings under seismic loading is often decided based on damage states observed in the structural and non-structural members. The type and extent of damage states exhibit a wide range depending on the structural system resisting the earthquake loading. While developing performance-based design methodologies, it is critical to provide computational tools to assess the available capacity of structural members corresponding to various performance-levels (e.g., Immediate Occupancy, Life Safety). In this paper the progression of local damage states (e.g., concrete crushing, steel yielding) of rectangular concrete-filled steel tube (RCFT) members and the effect of local damage states on the structural performance of composite RCFT frames was investigated using a new distributed plasticity finite element formulation. The computational findings of the detailed structural performance, particularly the interaction of the local damage states, were compared with experiments, as well as to damage indices of RCFT members and frames proposed by. Adopting the local damage states as the main design parameters, a performance-based design methodology is introduced and illustrated for the RCFT beam-columns of a three-story composite RCFT frame.
Performance-based-plastic-design of damage-control steel MRFs equipped with self-centring energy dissipation bays

Ke Ke,Xuhong Zhou,Huanyang Zhang,Michael C.H. Yam,Lihua Guo,Yonghui Chen

DOI: https://doi.org/10.1016/j.jcsr.2022.107230

IF: 4.349

2022-05-01

Journal of Constructional Steel Research

Abstract:Driven by the demand of producing novel seismic resilient structures, this study focused on steel moment resisting frames equipped with superelastic shape memory alloy (SMA) connections in the self-centring energy dissipation bays, and the emphasis was given to a direct-iterative design method for performance-based-plastic-design of the system under earthquake motions. Utilising the equivalent single-degree-of-freedom (SDF) oscillator which may reasonably quantify the dynamic responses of a multi-storey structure, an inelastic structural seismic demand model motivated by nonlinear spectral analyses was developed, and the statistic features were accounted. As the theoretical basis of the design philosophy, the seismic energy equilibrium equation of the structure was correlated with structural arrangement and earthquake motion characteristics. Then, a stepwise plastic design methodology enabling practising engineers to search for a feasible design strategy was proposed. Three prototype structures were developed following the proposed method, and finite element models of the systems were developed. The adequacy of the modelling techniques was verified by the test database, and the sufficiency of the hysteretic model of the structure was also justified. The seismic responses of the prototype structures were estimated by nonlinear static and dynamic analyses. The analysis data pool confirmed that the prototype structures were able to achieve the damage-control objective by limiting the maximum interstorey drifts below the prescribed deformation threshold, and inelastic actions were concentrated in the self-centring energy dissipation bays.

construction & building technology,engineering, civil
Numerical simulation and seismic performance analysis of sacrificial-energy dissipation beam-column joint

Xinlei Jin,Wenjie Liao,Yuan Tian,Linlin Xie,Xinzheng Lu

DOI: https://doi.org/10.1016/j.engstruct.2023.116979

IF: 5.582

2023-01-01

Engineering Structures

Abstract:To enable secondary energy-dissipating components to actively attract and dissipate seismic energy, a new type of sacrificial-energy dissipation beam-column joint (SEDJ) was proposed for frame structures. During strong earthquakes, the post-yield strength of the SEDJ was actively weakened by the shear failure of the bolts, and the friction between the friction plates and metal plate ensured that the SEDJ could fully dissipate the seismic energy. Meanwhile, the adjacent column and beam components remained elastic after the earthquake, so as to achieve the purpose of protecting the main beam and column components. Based on finite element analysis of the SEDJ using a solid element model, the expected seismic performance of the SEDJ was verified through displacement-controlled monotonic and cyclic loading tests. The peak strength Fu and post-yield strength Fr of the SEDJ could be controlled by adjusting the shear strength of the bolts and the preload of the friction plate and metal plate connecting bolts. Furthermore, the effectiveness of the SEDJ was evaluated by applying it to a three-story steel frame structure, and a parametric analysis was conducted. The results indicate that appropriately and actively reducing the post-yield strength of the SEDJ, with Fr/Fu equal to 0.3, provides the most favorable effect on improving the plastic dissipation energy distribution of the beam and column components and reducing the damage to the bottom column under strong earthquakes. Meanwhile, the structure meets the requirements of inter-story drift under design basis earthquakes and the collapse resistance under maximal considered earth-quakes. The SEDJ only requires the replacement of the bolts and friction plates after the earthquake. Therefore, this study can provide new ideas for designing seismic-resilient structures.

[Maxillary sinusitis].

Nonlinear Finite-Element Analysis of the Seismic Behavior of RC Column–Steel Beam Connections with Shear Failure Mode

Experimental study and numerical simulation of seismic performance of stiffened thin steel plate shear walls considering the effect of vertical load on frame column

Experimental Investigation on Performance of Cantilever CFRP-wrapped Circular RC Columns under Lateral Low-Velocity Impact

EXPERIMENTAL STUDY ON THE SEISMIC BEHAVIOR OF CFST RECTANGULAR COLUMN TO H-SECTION STEEL BEAM CONNECTIONS WITH EXTERNAL STIFFENERS

Seismic-design-oriented Classification of Structures and Members and Structure Influence Coefficient

Displacement-based Seismic Design Method for Square CFT Columns

Analysis on design parameters of seismic performance based on damage for recycled aggregate concrete-filled steel tube column

Seismic performance design of energy-dissipated structure system based on damage control and time-varying damping ratio

Design theory of earthquake-resilient prefabricated column foot joint with lateral force-resisting energy-consuming device

Seismic behaviour of pre-damaged RC columns strengthened with CFRP grid/sprayed ECC jackets subjected to horizontal reversed cyclic loading and constant axial force

Seismic Design Methodology Based on Damage Mechanism Control for Reinforced Concrete Structures

Seismic vulnerability of prefabricated reinforced concrete frame structure based on local outsource steel tube bolted column–column connection

Seismic performance evaluation of a novel resilient steel frame with self-centering rocking columns and replaceable energy-dissipating connections for low-rise structures

Numerical simulation of seismic behavior of earthquake damaged rc columns strengthened with frp

Research on design method of end stiffening ribs for square UHPCFHSST columns

Dynamic performance and cross-level damage criteria of strengthened reinforced concrete frames with VE energy dissipation braces

Seismic performance and damage properties of flexure–shear critical RC columns with various loading cycles

A Performance-Based Design Approach for Rectangular Concrete-Filled Steel Tube (RCFT) Frames under Seismic Loading

Performance-based-plastic-design of damage-control steel MRFs equipped with self-centring energy dissipation bays

Numerical simulation and seismic performance analysis of sacrificial-energy dissipation beam-column joint