Aqueous humor turnover rates in the cat. II. Effect of ouabain and chlorothiazide.

F. Macri,R. Dixon,D. Rall

1966-08-01

Abstract:Ouabain produced a dose-related inhibition in turnover rate of intracamerally administered "•C-labeled inulin. Chlorothiazide, even in high doses, had no detectable effects. No significant correlations were found between the turnover rate and IOP, anterior chamber volume, or femoral artery blood pressure.

What problem does this paper attempt to address?

Biofuels Production from Catalytic Cracking of Palm Oil Using Modified HY Zeolite Catalysts over A Continuous Fixed Bed Catalytic Reactor

I. Istadi,Teguh Riyanto,Luqman Buchori,Didi D. Anggoro,Andre W. S. Pakpahan,Agnes J. Pakpahan

DOI: https://doi.org/10.14710/ijred.2021.33281

2020-11-06

International Journal of Renewable Energy Development

Abstract:The increase in energy demand led to the challenging of alternative fuel development. Biofuels from palm oil through catalytic cracking appear as a promising alternative fuel. In this study, biofuel was produced from palm oil through catalytic cracking using the modified HY zeolite catalysts. The Ni and Co metals were impregnated on the HY catalyst through the wet-impregnation method. The catalysts were characterized using X-ray fluorescence, X-ray diffraction, Brunauer–Emmett–Teller (BET), Pyridine-probed Fourier-transform infrared (FTIR) spectroscopy, and Scanning Electron Microscopy (SEM) methods. The biofuels product obtained was analyzed using a gas chromatography-mass spectrometry (GC-MS) method to determine its composition. The metal impregnation on the HY catalyst could modify the acid site composition (Lewis and Brønsted acid sites), which had significant roles in the palm oil cracking to biofuels. Ni impregnation on HY zeolite led to the high cracking activity, while the Co impregnation led to the high deoxygenation activity. Interestingly, the co-impregnation of Ni and Co on HY catalyst could increase the catalyst activity in cracking and deoxygenation reactions. The yield of biofuels could be increased from 37.32% to 40.00% by using the modified HY catalyst. Furthermore, the selectivity of gasoline could be achieved up to 11.79%. The Ni and Co metals impregnation on HY zeolite has a promising result on both the cracking and deoxygenation process of palm oil to biofuels due to the role of each metal. This finding is valuable for further catalyst development, especially on bifunctional catalyst development for palm oil conversion to biofuels.
Catalytic deoxygenation of palm oil over metal phosphides supported on palm fiber waste derived activated biochar for producing green diesel fuel

Napat Kaewtrakulchai,Masayoshi Fuji,Apiluck Eiad-Ua

DOI: https://doi.org/10.1039/d2ra03496d

IF: 4.036

2022-09-14

RSC Advances

Abstract:Palm oil conversion into green diesel by catalytic deoxygenation (DO) is one of the distinctive research topics in biorefinery towards a bio-circular-green economic model to reduce the greenhouse gas emissions. In this study, palm fiber waste was explored as an alternative precursor for the preparation of activated biochar as a support material. A new series of nickel phosphide (Ni–P) and iron phosphide (Fe–P) catalysts supported on palm fiber activated biochar (PFAC) was synthesized by wetness impregnation, and extensive characterization was performed by several techniques to understand the characteristics of the supported metal phosphide catalysts prior to palm oil deoxygenation for producing of green diesel (C 15 –C 18 hydrocarbons). The PFAC support exhibited suitable physicochemical properties for catalyst preparation, such as high carbon content, and high porosity ( S BET of 1039.64 m 2 g −1 with V T of 0.572 cm 3 g −1 ). The high porosity of the catalyst support (PFAC) significantly promotes the metal phosphide nanoparticle dispersion. The DO of palm oil was tested in a trickle bed down flow reactor under hydrogen atmosphere. The outstanding catalytic performance of supported Ni–P and Fe–P catalysts provided an impressive liquid hydrocarbon yield between 63.37 and 79.65% with the highest green diesel selectivity of 62.64%. Decarbonylation (DCO) and decarboxylation (DCO 2 ) are the main pathways for the relative phosphide catalysts as presented by the high number of C n −1 atoms (C 15 and C 17 hydrocarbons). In addition, metal phosphide/PFAC catalysts could achieve great potential application as a promising alternative catalyst for biofuel production via deoxygenation for large-scale operation owing to their excellent catalytic activity, simple preparation, and utilization of sustainable resources.

chemistry, multidisciplinary
Conversion of palm fatty acid distillate to bio-jet fuel-range hydrocarbons over bimetallic NiCo/SBA-15-NH 2 catalyst

Darfizzi Derawi,Noor Azira Abdul Razak,Nasiha Sakinah Saadon,Najihah Abdul Bar,Yun Hin Taufiq-Yap

DOI: https://doi.org/10.1016/j.fuel.2024.133192

IF: 7.4

2024-09-21

Fuel

Abstract:The study revealed a successfully production of bio-jet fuel-range hydrocarbons from PFAD via hydrogen-free and solventless deoxygenation reaction over bimetallic NiCo/SBA-15-NH 2 catalyst. The NiCo/SBA-15-NH 2 catalyst showed reduced surface area and pore volume (393.93 m 2 /g and 0.39 cm 2 /g), respectively after the impregnation of Ni and Co metals. The XRD and XRF analysis confirmed the presence of Ni and Co elements in the catalyst, while demonstrating that the hexagonal structure of the SBA-15 support remained intact during the wet impregnation process. The NiCo/SBA-15-NH 2 catalyst also showed presence of weak and strong acid sites due to the existence of both –NH 2 and Ni-Co promoters. Indeed, HRTEM analysis revealed the distribution of Ni-Co metals on the surface of the catalyst support, hence increased the catalytic active sites. Therefore, the catalytic activity for the NiCo/SBA-15-NH 2 was evaluated via an optimization study at various reaction parameters, including temperature (270 °C, 300 °C, 315 °C, and 330°C), catalyst loading (0, 5, and 10 wt%), and reaction time (60–360 min). The results indicated that the highest yield of hydrocarbons (C8-C20) (83 %) and bio-jet selectivity (88 %) were achieved using a 5 % catalyst loading at 330°C for 300 min. This study provides valuable insights into the synthesis and catalytic performance of bimetallic NiCo/SBA-15-NH 2 catalysts for the production of bio-jet fuel from PFAD.

energy & fuels,engineering, chemical
Preparation of Ni/ZSM-5 and Mo/ZSM-5 catalysts for hydrotreating palm oil into biojet fuel

Wega Trisunaryanti,Karna Wijaya,Aulia Meylida Tazkia

DOI: https://doi.org/10.21924/cst.9.1.2024.1442

2024-07-16

Communications in Science and Technology

Abstract:With the increasing demand for fuel for global usage and CO2 emissions, greener alternatives are needed, especially in biojet fuel production. Catalyst preparation involves the impregnation of Ni and Mo metals into H-ZSM-5 using a dry impregnation method with spray deposition, resulting in Ni/ZSM-5 and Mo/ZSM-5 catalysts. Catalyst characterization utilizes FT-IR, XRD, SAA, SEM-EDX, XRF, and NH3-TPD instruments. The activity and selectivity tests of the catalysts were conducted in the hydrotreating of palm oil using Ni/ZSM-5 monolayer, Ni/ZSM-5 bilayer, Mo/ZSM-5 monolayer, Mo/ZSM-5 bilayer, as well as Ni/ZSM-5 bottom-layer and Mo/ZSM-5 top-layer arrangements. The result showed double-layer Ni/ZSM-5 as the best catalyst in activity and selectivity in producing biojet fuel fractions with consecutive conversion, selectivity, and yield of 29.71%, 84.76%, and 24.34%, respectively. The layers of catalyst affected the catalytic activity and selectivity, resulting in a higher yield.
Impact of Pt/Al-MCM-41 Catalyst Metal/Acid Ratio in Hydrocracking of Bio-Alkanes for Bio-Jet Fuel Production

Meizhen Lu,Libo Peng,Qinglong Xie,Yong Nie,Xuejun Liu,Jianbing Ji,Huajun Dong

DOI: https://doi.org/10.3969/j.issn.1003-0174.2018.05.010

2018-01-01

Abstract:The development of renewable liquid biofuel is a crucial route to increase the energy supply and reduce the pollutant emission.The catalysts were tested in the hydrocracking of bio-alkanes,produced from biodiesel hydrodeoxygenation for producing the bio-jet fuel.The ratio of metal sites to acid sites(CPt/CA)on Pt/Al-MCM-41 bifunctional catalyst was important to both the catalyst activity and product selectivity.Catalysts with different metal/acid ratios were prepared on Al-MCM-41 support with Si/Al ratio of 10 using various platinum loadings.Both the hydrocracking activity and selectivity to kerosene increased with the increasing in CPt/CA ratio in the range of 0.182 ～ 0.338.However,too high metal/acid ratio could cause the agglomeration of platinum particles,resulting in the waste of catalyst and reduction of catalyst activity and selectivity to kerosene.The optimal CPt/CA ratio was 0.203,under which the bio-alkanes conversion,kerosene yield and kerosene/gasoline ratio could reach 98.7％,47.0％ and 1.12,respectively.
Hydrocracking of Bio-Alkanes over Pt/Al-MCM-41 Mesoporous Molecular Sieves for Bio-Jet Fuel Production

Meizhen Lu,Xuejun Liu,Yongqiang Li,Yong Nie,Xianghong Lu,Dongshun Deng,Qinglong Xie,Jianbing Ji

DOI: https://doi.org/10.1063/1.4962561

IF: 2.847

2016-01-01

Journal of Renewable and Sustainable Energy

Abstract:Bi-functional catalysts consisting of platinum on aluminosilicate MCM-41 materials with Si/Al ratios between 10 and 30 were prepared via direct mixed-gel synthesis. The catalysts were tested in the hydrocracking of bio-alkanes, produced from biodiesel hydrodeoxygenation and composed of n-hexadecane and n-octadecane, for the production of bio-jet fuel. The effects of temperature, pressure, weight hourly space velocity (WHSV), and H2/n-paraffin weight ratio on bio-alkanes conversion and product distribution were examined. The conversion was found to be dependent on the acid strength of the catalyst supports which were proportional to the Al content. However, the catalyst selectivity decreased with the increasing Al content. The optimal Si/Al ratio, temperature, pressure, WHSV, and H2/n-paraffin weight ratio were determined to be 20, 330 °C, 2 MPa, 1 h−1, and 0.20, respectively. Under these conditions, the bio-alkanes conversion and kerosene/gasoline ratio in the product reached 65.62% and 1.96, respectively.
Hydrocracking of Palm Oil to Jet Biofuel over Different Zeolites

Tao Li,Jun Cheng,Rui Huang,Weijuan Yang,Junhu Zhou,Kefa Cen

DOI: https://doi.org/10.1016/j.ijhydene.2016.09.013

IF: 7.2

2016-01-01

International Journal of Hydrogen Energy

Abstract:The aim of this study is to develop zeolite catalysts to produce jet biofuel from palm oil. Different Ni-loaded zeolites were tested as catalysts in the conversion of palm oil into jet biofuels with high alkane and low arene content. Five zeolite catalyst, were tested: Ni/SAPO-34, Ni/MCM-41, Ni/HY, Ni/SAPO-11 and Ni/Hbeta. Characterization was performed by X-ray diffraction, NH3-temperature-programmed desorption. The Ni/SAPO-34 catalyst exhibited the highest alkane selectivity (65%) and lowest arene selectivity (11%). The jet biofuel yield under catalysis increased from 21.1 to 42.0% when the reaction temperature was increased from 370 to 390 degrees C. The alkane content of the jet biofuel increased from 71 to 80% and the arene content decreased from 29 to 20%, when the weight ratio of Si/Al in the Ni/HY catalyst was reduced from 11 to 5, but the levels were almost unchanged as the nickel content was increased from 5 to 20%. (C) 2016 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.
Single-step catalytic deoxygenation of palm feedstocks for the production of sustainable bio-jet fuel

Elaine Siew Kuan Why,Hwai Chyuan Ong,Hwei Voon Lee,Wei-Hsin Chen,N. Asikin-Mijan,Mahendra Varman,Wen Jing Loh

DOI: https://doi.org/10.1016/j.energy.2021.122017

IF: 9

2022-01-01

Energy

Abstract:The production of jet fuel from renewable source (i.e., biomass) has been improving since the past few years. In Malaysia, palm-based biomass is being widely studied for the production of transportation fuels due to its abundant supply. Hence, this study focused on the production of bio-jet fuel from different types of palm oil (e.g., palm-based waste cooking oil, palm olein, palm kernel oil) through deoxygenation process. Several types of deoxygenation catalysts (e.g., CaO, Zeolite, V2O5, Pd/C, TiO2) were selected to investigate the efficiency of jet fuel-based hydrocarbon production under condition of 400 °C for 2 h with different catalyst loading (e.g., 0 wt%, 5 wt%, 6 wt%, 7 wt%, 8 wt%, 9 wt% and 10 wt%). The physico-chemical properties of yielded liquid fuel were tested by using GC-MS analyses, as well as density, kinematic viscosity, cloud point, pour point, smoke point, flash point and final boiling point. The deoxygenation of PKO over Pd/C at 8 wt% yielded the highest molar concentration of 96% liquid product (e.g., n-paraffins, isoparaffins, olefins, naphthenes, aromatic) and 73% of jet paraffins selectivity (C8–C16) under 400 °C for 2 h. In addition, the physicochemical properties of palm-based liquid fuel are complied with standard Jet A-1 fuel, in accordance to ASTM standards. The low temperature fluidity, combustion characteristics, and fuel volatility of this liquid product were comparable to Jet A-1 fuel.

energy & fuels,thermodynamics
A Facile Molecular Precursor Route to Metal Phosphide Nanoparticles and Their Evaluation As Hydrodeoxygenation Catalysts

Susan E. Habas,Frederick G. Baddour,Daniel A. Ruddy,Connor P. Nash,Jun Wang,Ming Pan,Jesse E. Hensley,Joshua A. Schaidle

DOI: https://doi.org/10.1021/acs.chemmater.5b02140

IF: 10.508

2015-01-01

Chemistry of Materials

Abstract:Metal phosphides have been identified as a promising class of materials for the catalytic upgrading of bio-oils, which are renewable and potentially inexpensive sources for liquid fuels. Herein, we report the facile synthesis of a series of solid, phase-pure metal phosphide nanoparticles (NPs) (Ni2P, Rh2P, and Pd3P) utilizing commercially available, air-stable metal phosphine complexes in a one-pot reaction. This single-source molecular precursor route provides an alternative method to access metal phosphide NPs with controlled phases and without the formation of metal NP intermediates that can lead to hollow particles. The formation of the Ni2P NPs was shown to proceed through an amorphous Ni-P intermediate, leading to the desired NP morphology and metal-rich phase. This low-temperature, rapid route to well-defined metal NPs is expected to have broad applicability to a variety of readily available or easily synthesized metal phosphine complexes with high decomposition temperatures. Hydrodeoxygenation of acetic acid, an abundant bio-oil component, was performed to investigate H-2 activation and deoxygenation pathways under conditions that are relevant to ex situ catalytic fast pyrolysis (high temperatures, low pressures, and near-stoichiometric H-2 concentrations). The catalytic performance of the silica-supported metal phosphide NPs was compared to the analogous incipient wetness (IW) metal and metal phosphide catalysts over the range 200-500 degrees C. Decarbonylation was the primary pathway for H-2 incorporation in the presence of all of the catalysts except NP-Pd3P, which exhibited minimal productive activity, and IW-Ni, which evolved H-2. The highly controlled NP-Ni2P and NP-Rh2P catalysts, which were stable under these conditions, behaved comparably to the IW-metal phosphides, with a slight shift to higher product onset temperatures, likely due to the presence of surface ligands. Most importantly, the NP-Ni2P catalyst exhibited H-2 activation and incorporation, in contrast to IW-Ni, indicating that the behavior of the metal phosphide is significantly different from that of the parent metal, and more closely resembles that of noble metal catalysts.
Jet Fuel Range Hydrocarbons Production Through Competitive Pathways of Hydrocracking and Isomerization over HPW-Ni/MCM-41 Catalyst

Ze Zhang,Jun Cheng,Yanxia Zhu,Hao Guo,Weijuan Yang

DOI: https://doi.org/10.1016/j.fuel.2020.117465

IF: 7.4

2020-01-01

Fuel

Abstract:To promote hydrocracking and isomerization activities of bifunctional catalyst for the conversion of methyl palmitate into jet biofuel, phosphotungstic acid (HPW) loaded on Ni/MCM-41 catalyst enhanced strong acidity to strengthen conversion pathways of hydrocracking and isomerization. In the bifunctional catalytic system, Ni catalyzed hydrodeoxygenation and dehydrogenation of methyl palmitate to produce 1-pentadecene, while acid sites catalyzed further conversion of 1-pentadecene to produce jet fuel range hydrocarbons. Quantum chemistry calculation showed that activation energy in chemisorption process of 1-pentadecene onto acid sites significantly reduced from 203.9 kJ/mol with MCM-41 to 81.6 kJ/mol with HPW. Since bond order of beta-scission site in 1-pentadecene over HPW was 0.93% lower than that over MCM-41, and Hirshfeld atomic charge of carbenium ion in 1-pentadecene over HPW (0.0722) was much higher than that over MCM-41 (0.0473), HPW showed better catalytic activities than MCM-41 in both hydrocracking and isomerization processes. The overall selectivity of jet biofuel increased to 86.1% with 47.1% n-alkane selectivity and 8.3% iso-alkane selectivity, due to improved strong acid density from 0.563 to 0.730 mmol/g over 20% HPW-Ni/MCM-41 catalyst.
Improving the Bio-Oil Quality via Effective Pyrolysis/Deoxygenation of Palm Kernel Cake over a Metal (Cu, Ni, or Fe)-Doped Carbon Catalyst

Panya Maneechakr,Surachai Karnjanakom

DOI: https://doi.org/10.1021/acsomega.1c02999

IF: 4.1

2021-07-22

ACS Omega

Abstract:Waste palm kernel cake (WPKC) is being utilized as a biomass feedstock for the sustainable production of catalysts/supports and bio-oil fuels. Herein, metal (Cu, Ni, and/or Fe)-doped carbon catalysts were prepared using conventional impregnation and pyrolysis methods. The physicochemical properties of the as-prepared catalysts were analyzed. According to the obtained results, the catalyst acidity was highly increased with the increase in the metal loading amount on a carbon support, leading to a better performance for deoxygenation/aromatization. A maximum yield of bio-oil from WPKC pyrolysis was achieved up to ∼60% under optimum conditions determined via statistical designs. From the results of bio-oil compositions, 15%Ni loading on activated carbon exhibited the best performance of about 72% for the production of hydrocarbon compounds. Monoaromatic hydrocarbons such as benzene, toluene, and xylenes (BTXs) could be reduced via condensation and polymerization with the increase of the Ni-loading amount. Moreover, the catalytic performance of the selected 15%Ni-carbon catalyst was also compared with those of commercial catalysts zeolite and alumina, and the results showed that the 15% metal-doped carbon catalyst presented much better stability/reusability for five times with less reduction of the hydrocarbon yield in the upgraded bio-oil. This research provided an eco-friendly strategy for the low-cost production of bio-oil fuel with a high quality/yield from waste biomass pyrolysis.This article has not yet been cited by other publications.

chemistry, multidisciplinary
Highly efficient catalytic pyrolysis of biomass vapors upgraded into jet fuel range hydrocarbon-rich bio-oil over a bimetallic Pt–Ni/γ-Al2O3 catalyst

Yunwu Zheng,Jida Wang,Donghua Li,Can Liu,Yi Lu,Xu Lin,Zhifeng Zheng

DOI: https://doi.org/10.1016/j.ijhydene.2021.06.082

IF: 7.2

2021-08-01

International Journal of Hydrogen Energy

Abstract:Catalytic pyrolysis is an effective method for converting biomass to value-added chemicals. However, the development of cost-effective catalysts remains a major challenge. In this study, a highly efficient bimetallic Pt–Ni catalyst (Pt to Ni ratio = 0:1, 2:1, 1:1, 1:2, 1:0) was fabricated and used for catalytic biomass pyrolysis upgrading into hydrocarbon-rich bio-oil with pyrolysis-gaschromatography × gaschromatography/mass spectrometry (Py-GC∗ GC/MS). The product yield and selectivity of upgraded bio-oil, thermal properties, kinetic and deactivation mechanisms were also determined to investigate the reaction mechanism. It was determined that Pt addition strengthened the NiO and alumina interaction and improved nickel dispersion, promoting CO hydrogenation. Bimetallic catalysts had a higher stability and activity owing to synergistic action of platinum and nickel on γ-Al2O3, and the surface oxygen vacancies were derived from the electron transfer of Pt to Ni and the higher number of super acid-base sites, which inhibited coke deposition. In addition, the higher valence Pt (Pt2+) in the catalyst was favorable for decarboxylation and hydrodecarbonylation reactions. Various metal ratios were employed, and the Pt–Ni/Al = 1:2 catalyst exhibited an excellent catalytic performance, achieving highest peak areas of desired hydrocarbons and aromatic hydrocarbons at 52.67% and 40.25%, respectively, and the lowest peak area of deposited coke at 7.26%, along with a 13.98% weightloss rate.

energy & fuels,electrochemistry,chemistry, physical
Pyrolysis of Palm Fronds Waste into Bio-Oil and Upgrading Process Via Esterification-Hydrodeoxygenation Using Cu–Zn Metal Oxide Catalyst Loaded on Mordenite Zeolite

Ahmad Nasir Pulungan,Ronn Goei,Fauziyah Harahap,Lisnawaty Simatupang,Cicik Suriani,Saharman Gea,Muhammad Irvan Hasibuan,Junifa Layla Sihombing,Alfred Iing Yoong Tok

DOI: https://doi.org/10.1007/s12649-023-02153-0

2023-05-14

Waste and Biomass Valorization

Abstract:Bio-oil from the pyrolysis of palm fronds waste has potential to be used as an alternative fuel. However, due to its poor physicochemical properties, it requires further treatment to improve its overall quality. In this study, the conversion of palm fronds waste into bio-oil was carried out using the semi-fast pyrolysis at 500 °C and continued with esterification and hydrodeoxygenation (HDO). Metal oxides of Cu and Zn with a zeolite carrier mordenite (Mor) were used as bifunctional catalysts in the HDO reaction performed in a fixed-bed system reactor with temperature variations (250, 300, and 350 °C) for 2 h. Upgraded bio-oil (UBO) products at optimum conditions were analyzed for their physicochemical properties. In the pyrolysis process, the highest bio-oil conversion of 46.3% was obtained at a sample size of 60 mesh with the main component of furan compounds (46.31%). In the upgrading process through the esterification pretreatment, the optimum condition of HDO was determined to be at 300 °C, this can be seen from the high yield of liquid phase products produced on each catalyst (Mor; 89.85%, and CuO-ZnO/Mor; 88.25%). The physicochemical properties of upgraded bio-oil obtained under optimum conditions showed an increase in the quality of bio-oil with a decrease in water content (up to 23%), an increase in higher heating value (HHV) (up to 14.67% in CuO-ZnO/Mor). It is known that HDO with CuO-ZnO/Mor catalyst has a higher selectivity than Mor catalyst in converting aromatic hydrocarbon compounds such as methyl cyclohexane which is a potential component of a fuel.

environmental sciences
Bifunctional CaCO3/HY Catalyst in the Simultaneous Cracking-Deoxygenation of Palm Oil to Diesel-Range Hydrocarbons

Rosyad Adrian Febriansyar,Teguh Riyanto,I. Istadi,Didi D. Anggoro,Bunjerd Jongsomjit

DOI: https://doi.org/10.17509/ijost.v8i2.55494

2022-12-28

Indonesian Journal of Science and Technology

Abstract:Palm oil is a promising raw material for biofuel production using the simultaneous catalytic mechanism of the bifunctional cracking-deoxygenation reactions. Through the cracking-deoxygenation process, the chains of palmitic acid and oleic acid in the palm oil were converted to diesel-range hydrocarbons. The combination effects of CaCO3 and HY zeolite enhanced the bifunctional catalytic cracking-deoxygenation of palm oil into biofuel, because of the increasing acid and basic sites in the catalysts due to the synergistic roles of CaCO3 and HY. The introduction of CaCO3 on HY zeolite generated both a strong acid and strong basic sites simultaneously on the designed catalyst, which supports the bifunctional mechanisms of hybrid cracking-deoxygenation, respectively. The CaCO3 impregnated on the HY catalyst has a synergistic and bifunctional effect on the catalyst supporting cracking-deoxygenation reaction mechanisms as mentioned previously. The deoxygenation reaction required the bifunctional strong acid and strong basic sites on the CaCO3/HY catalyst through decarboxylation, decarbonylation, and hydrodeoxygenation reaction mechanisms. Meanwhile, the cracking reaction pathway was supported by the strong acid sites generated on the CaCO3/HY catalyst. In other words, the high acidity strength promotes diesel selectivity, whereas the high strength of basicity leads to the deoxygenation reaction.
Hydrocracking optimization of palm oil to bio-gasoline and bio-aviation fuels using molybdenum nitride-bentonite catalyst

Hasanudin Hasanudin,Wan Ryan Asri,Muhammad Said,Putri Tamara Hidayati,Widia Purwaningrum,Novia Novia,Karna Wijaya

DOI: https://doi.org/10.1039/d2ra02438a

IF: 4.036

2022-01-01

RSC Advances

Abstract:In this study, molybdenum nitride-bentonite was successfully employed for the reaction of hydrocracking of palm oil to produce a bio-gasoline and bio-aviation fuel.

chemistry, multidisciplinary
Catalytic Deoxygenation of Palm Oil Over Iron Phosphide Supported on Nanoporous Carbon Derived from Vinasse Waste for Green Diesel Production

Phetcharat Nenyoo,Peerawat Wongsurakul,Worapon Kiatkittipong,Napat Kaewtrakulchai,Atthapon Srifa,Apiluck Eiad-Ua,Suttichai Assabumrungrat

DOI: https://doi.org/10.1021/acsomega.4c05000

IF: 4.1

2024-10-01

ACS Omega

Abstract:The vinasse waste was effectively converted to nanoporous carbon (NPC) via hydrothermal carbonization with potassium hydroxide (KOH) activation. The nanoporous carbon (NPC) exhibited a maximum surface area of 1018 m2/g and it was utilized as a catalyst for the conversion of palm oil into green diesel fuel. The supported NPC catalyst was fabricated via a wet impregnation technique, where finely distributed iron phosphide (FeP) particles were cemented. The FeP/NPC catalyst was evaluated for its...

chemistry, multidisciplinary
Catalytic pyrolysis of coconut oil with Ni/SBA-15 for the production of bio jet fuel

Aldo Miro de Medeiros,Karoline de Sousa Castro,Mayara Lopes Gundim de Macêdo,Aruzza Mabel de Morais Araújo,Djalma Ribeiro da Silva,Amanda Duarte Gondim

DOI: https://doi.org/10.1039/d2ra00866a

2022-03-31

Abstract:Catalytic pyrolysis of vegetable oil is one of the potential routes to convert oil to drop-in biofuels, known as renewable hydrocarbons. In this paper, we explored catalytic pyrolysis of coconut oil using SBA-15 impregnated with Ni in proportions of 1% to 5% to produce sustainable aviation fuel. The catalysts were synthesized, calcined and then characterized by XRD, FTIR, SEM, and EDS. In order to better understand the behavior of this process, thermal and kinetic studies were carried out by thermogravimetry. The TG curves of vegetable oil with (10%) and without catalysts were obtained at heating rates of 5, 15 and 20 °C min-1, in the temperature range between 30 and 600 °C. The kinetic parameters were calculated by the Ozawa-Flynn-Wall (OFW) and Kissinger-Akahira-Sunose (KAS) methods. In the kinetic study, lower heat rates promoted higher conversions and the KAS model suits the process. The results calculated for the OC sample using the two kinetic models showed an increase in the E a energy as the conversion progressed to a certain point. Catalytic pyrolysis experiments were performed in a one-stage tubular reactor at 500 °C with a catalyst loading of 10 wt% on the basis of mass of oil. The catalyst with 5% Ni showed greater presence of hydrocarbons and greater formation of water, indicating that the deoxygenation process occurred through decarbonylation. With this, the present study was successful in the development of methodologies for obtaining hydrocarbons with a composition close to that of drop-in fuels, compared to the process carried out with vegetable oil in the absence of catalysts.
Compositional dependence of Co- and Mo-supported beta zeolite for selective one-step hydrotreatment of methyl palmitate to produce bio jet fuel range hydrocarbons

Su-Un Lee,Tae-Wan Kim,Kwang-Eun Jeong,Sungjune Lee,Min Cheol Shin,Chul-Ung Kim

DOI: https://doi.org/10.1039/d2ra06938e

IF: 4.036

2023-01-18

RSC Advances

Abstract:For producing a drop-in bio jet fuel, one-step hydrotreatment, which includes deoxygenation, isomerization and cracking in one step, is essential to overcome the typical biofuel drawbacks due to high oxygen content, out of jet fuel range hydrocarbons, and low isomerization degree. Herein, Co- or/and Mo-supported Beta(25) zeolites with various Co/Mo ratios were prepared as transition metal-supported zeolite catalysts without the need for sulfidation of conventional transition metal catalysts. Based on the catalyst characterization, the Co/Mo ratio alters the metal phase with the appearance of CoMoO 4 and the altered Co metal phase strongly influences the acidic properties of Beta(25) by the formation of Lewis (L) acid sites with different strengths as Co 3 O 4 and CoMoO 4 for strong and weak L acid sites, respectively. The catalytic activities were investigated for hydrotreatment of methyl palmitate as a biofuel model compound of fatty acid methyl esters. Primarily, Co is required for deoxygenation and Mo suppresses overcracking to enhance the yield of jet fuel range hydrocarbons. The Co/Mo ratio plays an important role to improve the C 8 –C 16 selectivity by modifying the acidic properties to inhibit excessive cracking. Co 5 Mo 10 /Beta(25) achieved the best catalytic performance with the conversion of 94.2%, C 8 –C 16 selectivity of 89.7 wt%, and high isomer ratio of 83.8% in organic liquid product. This unique modification of acidic properties will find use in the design of optimal transition metal-supported zeolite catalysts for selective one-step hydrotreatment to produce bio jet fuel range hydrocarbons.

chemistry, multidisciplinary
Nickel Supported Parangtritis Beach Sand (PP) Catalyst for Hydrocracking of Palm and Malapari Oil into Biofuel

Muh. Siddik Ibrahim,Wega Trisunaryanti,Triyono Triyono

DOI: https://doi.org/10.9767/bcrec.17.3.15668.638-649

2022-09-23

Abstract:Nickel supported Parangtritis beach sand (PP) catalyst for hydrocracking of palm and malapari oil into biofuel has been conducted. The impregnation process of Nickel (Ni) metal on PP was carried out through the dry impregnation method (blending) using a precursor salt of NiCl2.6H2O with variations of Ni metal as much as 10 and 15 wt% of PP which produced Ni(A) and Ni(B) catalysts. Each catalyst was tested for activity and selectivity through the hydrocracking process of oil into biofuel using a semi-batch system reactor at a temperature of 450 oC, a hydrogen gas flow rate of 20 mL/minute for 2 hours, and a weight ratio of 1:200 catalyst:feed (w/w). The results showed that the Ni(A)/PP catalyst had the highest activity and selectivity with the yield of liquid products and the total biofuel fraction (biohydrocarbons) obtained from hydrocracking of palm oil of 68.50 and 49.87 wt%, respectively. Ni(A)/PP catalyst has a total acidity, surface area, and crystal size of 0.051 mmol/g, 4.44 m2/g, 25.86 nm, respectively. The reusability test of the Ni(A)/PP catalyst in the hydrocracking process of palm oil into biofuel after the third use resulted in a liquid product and the total biofuel fraction obtained was 64.20 and 41.46 wt%, respectively. The yield of liquid product and the total fraction of biofuel (biohydrocarbon) in hydrocracking malapari oil were 66.10, 47.83 wt%, respectively. Copyright © 2022 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).
Upgrading biomass-derived pyrolysis bio-oil to bio-jet fuel through catalytic cracking and hydrodeoxygenation: A review of recent progress

Pooya Lahijani,Maedeh Mohammadi,Abdul Rahman Mohamed,Farzad Ismail,Keat Teong Lee,Ghazaleh Amini

DOI: https://doi.org/10.1016/j.enconman.2022.115956

IF: 10.4

2022-09-15

Energy Conversion and Management

Abstract:Biomass-to-liquid thermochemical routes are the leading green alternatives for producing sustainable hydrocarbon fuels in the near future, including bio-jet fuel. Fast pyrolysis is among the most prospective approaches for converting waste biomass, including agricultural wastes and forestry residues, into liquid fuels. However, despite its maturity, pyrolysis-derived bio-oil bears a poor quality, attributed to the presence of numerous oxygenated compounds and high water content, making it chemically unstable, viscous, and corrosive, with a low heating value. Such inferior properties exclude the direct use of bio-oil as a drop-in fuel, and extensive upgrading is required before it could be utilized as a kerosene fraction and/or blend. Two catalytic post-treatment approaches have shown to be most promising for upgrading bio-oil and refining it to a finished product; catalytic cracking of fast pyrolysis vapor and hydrodeoxygenation. This review focuses on the conversion of biomass-derived bio-oil, excluding triglyceride-based oils, into jet fuel range hydrocarbon through catalytic cracking (associated with catalytic fast pyrolysis) and hydroprocessing (hydrogenation and hydrodeoxygenation), according to the most recent literature efforts. It provides an in-depth overview of the challenges and most recent progress in upgrading real pyrolysis bio-oil to bio-jet fuel through these two routes, emphasizing the conversion pathways. Due to the complex composition of raw bio-oil, very few studies have been devoted to mechanistic aspects of raw bio-oil upgrading, and most studies have been focused on individual model compounds. Hence, research opportunities remain open for extensive studies on real bio-oil upgrading to bio-jet fuels.

energy & fuels,thermodynamics,mechanics

Aqueous humor turnover rates in the cat. II. Effect of ouabain and chlorothiazide.

Biofuels Production from Catalytic Cracking of Palm Oil Using Modified HY Zeolite Catalysts over A Continuous Fixed Bed Catalytic Reactor

Catalytic deoxygenation of palm oil over metal phosphides supported on palm fiber waste derived activated biochar for producing green diesel fuel

Conversion of palm fatty acid distillate to bio-jet fuel-range hydrocarbons over bimetallic NiCo/SBA-15-NH 2 catalyst

Preparation of Ni/ZSM-5 and Mo/ZSM-5 catalysts for hydrotreating palm oil into biojet fuel

Impact of Pt/Al-MCM-41 Catalyst Metal/Acid Ratio in Hydrocracking of Bio-Alkanes for Bio-Jet Fuel Production

Hydrocracking of Bio-Alkanes over Pt/Al-MCM-41 Mesoporous Molecular Sieves for Bio-Jet Fuel Production

Hydrocracking of Palm Oil to Jet Biofuel over Different Zeolites

Single-step catalytic deoxygenation of palm feedstocks for the production of sustainable bio-jet fuel

A Facile Molecular Precursor Route to Metal Phosphide Nanoparticles and Their Evaluation As Hydrodeoxygenation Catalysts

Jet Fuel Range Hydrocarbons Production Through Competitive Pathways of Hydrocracking and Isomerization over HPW-Ni/MCM-41 Catalyst

Improving the Bio-Oil Quality via Effective Pyrolysis/Deoxygenation of Palm Kernel Cake over a Metal (Cu, Ni, or Fe)-Doped Carbon Catalyst

Highly efficient catalytic pyrolysis of biomass vapors upgraded into jet fuel range hydrocarbon-rich bio-oil over a bimetallic Pt–Ni/γ-Al2O3 catalyst

Pyrolysis of Palm Fronds Waste into Bio-Oil and Upgrading Process Via Esterification-Hydrodeoxygenation Using Cu–Zn Metal Oxide Catalyst Loaded on Mordenite Zeolite

Bifunctional CaCO3/HY Catalyst in the Simultaneous Cracking-Deoxygenation of Palm Oil to Diesel-Range Hydrocarbons

Hydrocracking optimization of palm oil to bio-gasoline and bio-aviation fuels using molybdenum nitride-bentonite catalyst

Catalytic Deoxygenation of Palm Oil Over Iron Phosphide Supported on Nanoporous Carbon Derived from Vinasse Waste for Green Diesel Production

Catalytic pyrolysis of coconut oil with Ni/SBA-15 for the production of bio jet fuel

Compositional dependence of Co- and Mo-supported beta zeolite for selective one-step hydrotreatment of methyl palmitate to produce bio jet fuel range hydrocarbons

Nickel Supported Parangtritis Beach Sand (PP) Catalyst for Hydrocracking of Palm and Malapari Oil into Biofuel

Upgrading biomass-derived pyrolysis bio-oil to bio-jet fuel through catalytic cracking and hydrodeoxygenation: A review of recent progress