Group B streptococcal cellulitis-adenitis in a previously normal child.

H. M. Feder,K. Pae

DOI: https://doi.org/10.1097/00006454-199209000-00019

1992-09-01

Abstract:

What problem does this paper attempt to address?

Experimental study on the thermal performance of a solar air heater integrated with multi-geometry arrangements over the absorber plate

Vijayakumar Rajendran,Harichandran Ramasubbu,Jaya Venkatesh Rajarathinam,Ramanan Pichandi

DOI: https://doi.org/10.1007/s11356-022-18830-x

Abstract:A solar air heater (SAH) is investigated experimentally by employing multi-geometry arrangements over the absorber plate. In the current work, the absorber plate is designed with rectangular ribs, slits, and cylinders. For the proposed system, this multi-geometry arrangement serves as an artificial roughness (baffles). Different airflow rates of 0.01, 0.02, 0.03, and 0.04 kg/s are used in the experiment. The results of this experiment are compared to those of a conventional SAH to assess the improvement. Compared to a conventional SAH, the proposed system has higher thermal efficiency, energy gain, and minimal top loss. The highest thermal efficiency and energy gain are observed at a mass flow rate of 0.04 kg/s. Increasing the mass flow rate increases the system's performance. For the analyzed flow rates, the average thermal efficiency of a SAH with multi-geometry baffle is 40.8%, 58.2%, 68.2%, and 77.4%. For the same flow rates, it is 12.8%, 10.2%, 12.3%, and 13.5% higher than a conventional SAH. For the same examined air flow rates, the suggested air heater gains 31.9%, 21%, 19.2%, and 20.8% more energy than conventional SAH. Significant decreases in top losses are reported up to 8.1%, 7.3%, 7.2%, and 6.5%, respectively for the specified flow rates.
Investigation on energy, economic, and environmental aspects of double-pass solar air heater

Rajendran Vijayakumar,Ramalingam Vignesh Kumar,Petchimuthu Madhu

DOI: https://doi.org/10.1007/s11356-024-33786-w

IF: 5.8

2024-06-01

Environmental Science and Pollution Research

Abstract:Numerous research studies have found that a double-pass solar air heater (DPSAH) performs better than a single-pass solar air heater (SAH). This suggested study aims to evaluate the performance of a DPSAH setup in Southern Tamil Nadu, India. Several artificial roughness features have been incorporated into the solar black-coated absorber plate for this examination. Broken ribs with semi-circular and semi-polygonal shapes are used and explicitly tested on the absorber plate. Next, the efficiency of these rib designs is contrasted with a typical flat plate DPSAH. These studies also employ three different mass flow rates (0.01 kg/s, 0.02 kg/s, and 0.03 kg/s), enabling a thorough assessment of the DPSAH system's performance at each rate. These studies' findings demonstrate that adding artificial roughness to the solar collector plate has a beneficial effect on the turbulence of fluid flows. As a result, this innovation increases the double-pass solar air heater's (DPSAH) heat transfer rate. It is noteworthy that compared to the DPSAH with flat plates, both rib designs perform better. It is important to remember that the semi-polygonal ribs function better than the semi-circular ones. The average efficiency values for the semi-polygonal rib structure are 17.1%, 18.7%, and 19.1% greater than those seen for flat plates. These efficiency values are additionally 4.4%, 7.4%, and 8.7% higher than those attained with the semi-circular rib topologies at flow rates of 0.01 kg/s, 0.02 kg/s, and 0.03 kg/s, respectively. The study goes into considerable detail on how particular rib patterns can be advantageous economically and environmentally.

environmental sciences
Experimental analysis of a solar air heater using waste mild steel chips as a sensible heat storage material

Harjyoti Das,Pooja Dutta,Partha Pratim Dutta,Pradyumna Kumar Choudhury

DOI: https://doi.org/10.1007/s11356-024-35415-y

IF: 5.8

2024-11-04

Environmental Science and Pollution Research

Abstract:Heat storage materials improve the utility of solar air heaters (SAHs) after sunset. This study investigates an improved solar air heater (SAH) performance with baffles and waste mild steel chips as sensible heat storage (SHS) materials. Comparative experimental natural convection heat transfer studies were performed with four different improved air heater setups under similar solar radiation conditions. These setups consist of a flat collector plate (I), a baffled plate collector (II), a flat plate collector with SHS (III) and a baffled plate collector with SHS (IV) respectively. Setups I, II, III and IV were obtained by modifying the same air heater enclosure and each experiment was replicated for three similar sunny days. During the periods, the solar radiation varied in the range of 556–934 W/m 2 . The maximum thermal efficiencies found for setups I, II, III and IV were 18.76%, 22.40%, 27.21% and 28.22% respectively under natural convection. The highest average useful energy rate was produced by setup IV, followed by setups III, II and I. After sunset, setups III and IV were able to deliver warm air for an extended period of 1 h, 18 min and 1 h, 42 min, respectively. It was found that setups III and IV had sensible thermal energy storage reserves of 0.38 kJ and 0.53 kJ, respectively. The storage efficiencies found for setups III and IV were 60.25% and 70.89%, respectively. Among the four setups, setup IV boasts the most economical energy cost at 1.39 ₹/kWh and having the least payback period of 1 year 4 months. As a result, the employment of baffles and waste mild steel chips as SHS in a flat plate SAH not only presents a method for harvesting waste for efficient heat retention, but it also effectively uses solar energy for beneficial uses.

environmental sciences
Energy and exergy experimental analysis for innovative finned plate solar air heater

Abdullah Alrashidi,Ahmed A. Altohamy,M.A. Abdelrahman,Ismail M.M. Elsemary

DOI: https://doi.org/10.1016/j.csite.2024.104570

IF: 6.268

2024-05-29

Case Studies in Thermal Engineering

Abstract:In this current experimental study, a flat absorber plate of a solar air heater (SAH) with innovative straight interrupted fins arranged in a V-shaped pattern is analyzed using energy and exergy approaches, as the literature clearly shows that the low rate of heat transfer of flat plate SAH remains a source of concern for energy experts. The aluminum finned absorption plate was designed, manufactured, and tested during the summer in Saudi Arabia, examining the effect of changing the SAH tilt angle of θ = 0°, θ = 10°, θ = 20°, and θ = 30°. The study found that tilting the SAH at θ = 10°, θ = 20°, and θ = 30° increases the hot air exit temperature by 7.5 %, 15.7 %, and 12.5 %, respectively, compared to the horizontal position at θ = 0°. Tilting the SAH to θ = 20° increased absorbed solar radiation and air draft, resulting in 38.2 % SAH energy efficiency, 26.4 % exergy efficiency, and a 1.36 sustainability index that increased by 5.5 %, 12.8 % and 3.8 % compared to the horizontal position θ = 0°.

thermodynamics
Gastrointestinal hormones: environmental cues for Fasciola hepatica?

M. Sukhdeo,S. C. Sukhdeo

DOI: https://doi.org/10.1017/S0031182000062144

1989-04-01

Parasitology

Abstract:SUMMARY The effects of pharmacological concentrations of several gastrointestinal hormones on the rate of sucker activity and the frequency and the amplitude of spontaneous longitudinal muscle contractions have been examined in adult Fasciola hepatica. Caerulein and serum decrease the rate of oral sucker activity; motilin decreases and CCK–PZ increases ventral sucker activity when compared to controls. Caerulein, serum and motilin significantly inhibit the frequency of contractions while bile, caerulein and motilin decrease the amplitude of contractions. These results suggest that F. hepatica can recognize and respond to certain gastrointestinal hormones and there may be adaptive value in these behavioural responses.
Numerical analysis of a solar air heater with offset transverse ribs placed near the absorber plate

Jay Shankar Prasad,Aparesh Datta,Sirshendu Mondal

DOI: https://doi.org/10.1016/j.renene.2024.120608

IF: 8.7

2024-05-09

Renewable Energy

Abstract:Solar air heater (SAH) is used to convert readily available solar energy into useful thermal energy. Several studies have been conducted with different roughness elements on the absorber plate. However, study with ribs which are placed slightly above the heated plate, termed as offset transverse ribs, are still scant in the literature. Such study would explain the effect of flow between the ribs and the absorber plate on heat transfer augmentation in a SAH. With this objective a 2-D numerical study is performed here by solving steady RANS equations with RNG k−ɛ turbulence model. The effect of offset transverse ribs on heat transfer, pressure drop and thermal enhancement factor ( TEF ) is investigated. The geometrical parameters, such as, relative gap ( α ), relative height ( β ) and relative pitch ( λ ) are varied in the range of 0.0–0.045, 0.015 to 0.09, and 0.0333 to 0.1, respectively. The performance of SAH is evaluated on the basis of highest enhancement in relative Nusselt number ( NuR/Nu ) and thermal enhancement factor ( TEF ). A slight gap between the ribs and the absorber plate ( α = 0.0075) is observed to yield better thermal performance than that for the attached ribs ( α = 0). The maximum enhancement in NuR/Nu is found to be 1.52 for α = 0.0075. However, increasing the gap (i.e., α ) prevents the flow reattachment with the absorber plate. Increase in rib height, on the other hand, is found to be more effective in heat transfer enhancement, but with a price of a significant enhancement in pressure drop. This leads to a reduction in the overall performance of SAH. Increment in pitch distance, however, reduces the enhancement in both Nusselt number and friction factor. By considering these three parameters, the highest TEF is found to be 1.042 for α=0.0075 , β=0.030 , and λ=0.0333 at Re equal to 13000. Finally, correlations for NuR and fR are derived as a function of the parameters investigated for helping the design of SAHs.

energy & fuels,green & sustainable science & technology
Effect of the baffle's type on thermal performance of solar air heaters

Yuan Chang,Yibing Xue,Geng Geng

DOI: https://doi.org/10.1016/j.csite.2024.104580

IF: 6.268

2024-05-24

Case Studies in Thermal Engineering

Abstract:To determine the optimal baffle's type (longitudinal and transverse baffles) and the number of baffles, two computational fluid dynamics (CFD) models for solar air heaters (SAHs) were developed by using "ANSYS Fluent" software. The computational results closely aligned with the experimental data. As the width of the air channel in SAHs with transverse baffles was narrower than in those with longitudinal baffles under the same number of baffles, the heat transfer coefficient of SAHs with transverse baffles was greater than those with longitudinal baffles. Thus, for the airflow rate ( m ̇ ) range of 0.013 kg s −1 to 0.078 kg s −1 , SAHs with transverse baffles exhibited 2.34 %–6.97 % higher collection efficiency compared to those with longitudinal baffles. An analysis of the impact of the number of transverse baffles ( N ) on the flow and heat transfer characteristics in SAHs revealed that both the size and intensity of the vortex zones increased with an increase in N , thereby influencing the heat transfer between the air and the absorber plate. Specifically, among the studied values of N (2, 4, 6, and 8), at = 0.026 kg s −1 , N = 4 achieved the peak effective efficiency at 54.32 %. Conversely, for m ̇ = 0.039 kg s −1 , 0.052 kg s −1 , 0.065 kg s −1 , and 0.078 kg s −1 , the highest effective efficiency was observed at N = 6, with values of 60.03 %, 63.78 %, 64.39 %, and 64.38 %, respectively.

thermodynamics
Impact of corrugated duct and heat storage element on the performance of a low-cost solar air heater under forced air circulation: an experimental study

Beno Wincy Winsly,Joseph Sekhar Santhappan,Murugan Paradesi Chockalingam

DOI: https://doi.org/10.1007/s11356-024-33491-8

IF: 5.8

2024-05-02

Environmental Science and Pollution Research

Abstract:The need to address global warming issues and international policies has placed a greater emphasis on the development of solar energy utilization systems. Intensive study is necessary to expand solar energy applications, as solar energy potential varies widely. This study investigates the thermal and thermohydraulic performance of a modified flat plate solar air heater (FSAH) to assess the effects of using corrugated aluminium duct and sand heat storage elements (HSE) in various combinations. The different arrangements selected for the experimental investigation are the FSAH, FSAH with corrugated aluminium duct (FSAH-C), FSAH with a sand heat storage element (FSAH-S), and FSAH with a combined use of corrugated aluminium duct and a sand heat storage element (FSAH-CS). The materials used for fabrication are low-cost and readily available in the study area. The results indicate that the sand bed enhanced the thermal performance by acting as the thermal heat storage medium, which could also supply heat for a short duration after non-sunny hours, and the corrugated aluminium duct enhanced the surface area and allowed the air to pass twice inside the SAH. We observed that the SAHs with sensible heat storage had a higher top loss compared to the FSAH-S configuration. The average thermal efficiency of the FSAH-CS configuration was 59.17%, which is 8.81%, 5.72%, and 10.95% higher than FSAH-S, FSAH-C, and FSAH, respectively. Furthermore, this configuration achieved an exit temperature of 64.5 °C. The proposed system has a thermohydraulic efficiency of 59.14%, which is not significantly different from the average thermal efficiency. Therefore, the suggested system verifies its ability to function without requiring substantial external power.

environmental sciences
Thermal performance evaluation of a solar air heater integrated with helical tubes carrying phase change material

Abhishek Saxena,Nitin Agarwal,Erdem Cuce

DOI: https://doi.org/10.1016/j.est.2020.101406

IF: 9.4

2020-08-01

Journal of Energy Storage

Abstract:In this present work, the efforts have been made to improve the efficiency of solar air heater (SAH). For this, total two models have been developed. There is one reference model SAH-A and one modified model SAH-B which is integrated with paraffin wax as a low cost energy storage material. Furthermore, model SAH-B is further modified into a new model SAHC which is integrated with a specific mixture of paraffin wax and Granular coarbon powder (GCP). For better heat storage capacity of the aforesaid energy materials, helical tube of copper made has been considered as a container. Both the models of air heater (SAH-B and SAHC) have been experimentally tested on natural and forced convection under the climatic conditions of Moradabad city, India. Results show that SAH- C is better over SAH-A and SAH-B in performance comparison. Thermal efficiency of SAHC is found to be 79.10%, whereas it is found around 57.41% for SAH-B and around 50% for SAH-A. The other major parameter is heat transfer coefficient and for SAHC it is found to be 411.05 W/m2K, whereas it is found around 389 W/m2K for SAH-B and around 249.19 W/m2K for SAH-A. The maximum exhaust temperature of SAHC is reported to be 52.5 °C, whereas it is observed around 46.9 °C for SAH-B and about to be 44.7 °C for SAH-A. The main parameters of the present work summarizes that the model SAHC is an economic and optimum model for space heating, timber seasoning, drying operations etc. The total cost of the best configured SAHC model is only $67.

energy & fuels
Experimental Study of the Effect of Porous Media on the Performance of Single-Pass Solar Air Heater

Asmaa Mohammed Hameed,Akeel Abbas Mohammed,Emad Kamil Hussain

DOI: https://doi.org/10.37934/arfmts.121.1.2738

2024-09-15

Journal of Advanced Research in Fluid Mechanics and Thermal Sciences

Abstract:Solar energy is harnessed to heat the air, which is then utilised for warming greenhouses and drying crops. Solar air heaters may readily increase their performance using an absorbent plate design with a front pass of steel wools. This kind of SAH has been investigated and compared to a conventional flat absorbent plate. Steel wool, a cost-effective and permeable substance, possesses excellent heat conductivity, and it can be utilised in ongoing initiatives to enhance convection and thermal efficiency. The analysis in this research is based on data from experiments, focusing on the single-pass SAH technique and considering two scenarios: traditional system and porous system, with air mass flow rates of 0.015 Kg/s and 0.035 Kg/s. The experimental findings show that employing porous materials increases the exhaust temp by 12.28% and 21.32 % form of air 0.015 and 0.035 Kg/s, respectively. Moreover, the solar radiation readings for non-porous and porous medium SAHs were recorded as 905.32-912.92 and 979.04-945.6 W/m2, respectively, at 1:30 p.m. Furthermore, thermal efficiency is between 33.29 % and 64.36 % in the porous scenarios and between 30.12% and 57.36% for non-porous cases. Porous media increases the thermal efficiency by 10 % and mass flow rate by 14 %.
Dialysis search filters for PubMed, Ovid MEDLINE, and Embase databases.

Arthur V. Iansavichus,R. Haynes,Christopher W. C. Lee,N. Wilczynski,A. Mckibbon,Salimah Z. Shariff,P. Blake,R. Lindsay,Amit X. Garg,Amit X. Garg

DOI: https://doi.org/10.2215/CJN.02360312

2012-10-01

Abstract:BACKGROUND AND OBJECTIVES Physicians frequently search bibliographic databases, such as MEDLINE via PubMed, for best evidence for patient care. The objective of this study was to develop and test search filters to help physicians efficiently retrieve literature related to dialysis (hemodialysis or peritoneal dialysis) from all other articles indexed in PubMed, Ovid MEDLINE, and Embase. DESIGN, SETTING, PARTICIPANTS, & MEASUREMENTS A diagnostic test assessment framework was used to develop and test robust dialysis filters. The reference standard was a manual review of the full texts of 22,992 articles from 39 journals to determine whether each article contained dialysis information. Next, 1,623,728 unique search filters were developed, and their ability to retrieve relevant articles was evaluated. RESULTS The high-performance dialysis filters consisted of up to 65 search terms in combination. These terms included the words "dialy" (truncated), "uremic," "catheters," and "renal transplant wait list." These filters reached peak sensitivities of 98.6% and specificities of 98.5%. The filters' performance remained robust in an independent validation subset of articles. CONCLUSIONS These empirically derived and validated high-performance search filters should enable physicians to effectively retrieve dialysis information from PubMed, Ovid MEDLINE, and Embase.
Thermal Performance Factor of Impinging Jet‐Angled Corrugated Solar Air Heaters

Aneeq Raheem,Waseem Siddique,Khalid Waheed,Imran Aziz,Irfan Javed,Kamran Qureshi,Muhammad Zaki,Muhammad Tabish Raheem,Muhammad Muneeb Yaseen

DOI: https://doi.org/10.1002/ente.202301140

IF: 4.149

2024-03-17

Energy Technology

Abstract:Solar air heaters (SAHs) are one the common applications of solar energy but they have generally low efficiency. To increase their efficiency, a novel impinging‐corrugated SAH is proposed and numerically investigated over a range of Reynolds numbers, jet‐to‐target plate distance, corrugation angle, and various jet profiles. These promising designs will effectually modify the traditional tendencies in renewable energy. Solar energy is a clean and sustainable source of power generation. There are various industrial and domestic applications of Solar Air Heaters (SAHs), but their low thermal efficiency poses a challenge. To improve thermal efficiency, a novel‐angled corrugated jet‐impinging channel has been proposed for the absorbing plate of SAHs. A numerical study has been performed for four different arrangements of jets, i.e., single circular, single square, 2 × 2 square, and 3 × 3 square jet array with four channels, i.e., 30°, 45°, 60°, and 90° corrugated over the Reynolds number range of 1600–2700 for the jet to target plate range of 4.9–15. It is observed that multiple jets impinging increases the heat transfer significantly. The optimization has been performed by instigating the parametric study. Flow and thermal profiles are studied. The 45° corrugated target plate with 3 × 3 multiple jet impingement, 4.9 jet‐to‐target plate distance, and 2700 Reynolds number is chosen to have the best thermal efficiency. A Thermal Performance Factor of around 8 was achieved as compared to the base case.

energy & fuels
Analysis of solar air heaters based on computational fluid dynamics

Chinmaya Mund,Sushil Kumar Rathore,Ranjit Kumar Sahoo

DOI: https://doi.org/10.1007/s10973-023-12855-1

IF: 4.755

2024-02-18

Journal of Thermal Analysis and Calorimetry

Abstract:The energy requirement of the world will keep on rising, and fossil fuels have been increasingly used in this regard. The use of fossil fuels brings about different sets of problems like climate change, greenhouse gas emissions, etc. So, a desperate need for an alternative source of energy which can be cheap and sustainable is being felt. Renewable forms of energy are environment friendly and can be looked into for our energy needs. Among renewable forms of energy, solar energy is free and extensively obtainable. This paper reviews solar air heater (SAH) that utilizes solar energy to provide medium temperature air output. The main disadvantage of SAH is its low efficiency. So, researchers have used different ways to improve its efficiency. This paper looks into the numerical methods and new techniques implemented by investigators to numerically model a SAH while organizing their results in a tabular form. Subsequently, the study analyses the thermal performance of SAH in terms of thermohydraulic performance parameter (THPP) and organizes their results in tabular form. The maximum THPP achieved among the cases studied was from Jouybari and Lundstrom (Energy 190:116437, 2020) and equalled 5.5. Finally, the current study will provide researchers with a quick view of the turbulence models used by investigators along with information on the number of grids to gauge the computational power required for the study and concludes with few key points on the subjects that can be further explored.

chemistry, physical, analytical,thermodynamics
Experimental Study of Reverse Flow Solar Air Heater Having Perforation and Delta Wing on Absorber Plate

Sohan Lal Sharma,Ajoy Debbarma

DOI: https://doi.org/10.1002/ente.202301246

IF: 4.149

2024-01-18

Energy Technology

Abstract:A new design of solar air heater (SAH) (perforation and delta wing (DW) on absorber) is presented experimentally. Thermo‐hydraulic performance is carried out for different attack angles (α = 15°, 30°, 45°, 60°, and 75°) of DW. It shows better thermal and thermohydraulic performance (THP) as compared to plane SAH. The maximum value of THP is equal to 3.06, for an attack angle of 75° at Re of 4000. fThe traditional solar air heater (SAH) has poor thermal performance due to low heat transfer coefficient. Artificial roughness, flow passage alteration, absorber modification, etc. can enhance it. Thus, an experimental investigation is performed to study the thermohydraulic characteristics of a reverse flow SAH with perforated absorber and delta wing (DW) structure. The present study investigates the effect of attack angle (15°–75°) at constant streamwise pitch (35 mm), transverse pitch (70 mm), height (h), and width (w) of DW 20 mm, under Reynolds number (Re) ranging from 4000 to 20 000. The perforation index (PI = ADW/Aap) for inline and staggered arrangements are 9.52 and 4.76, respectively. The results indicate that the concept of perforated absorber and DW leads to enhanced heat transfer, reduced pressure drops, and enhanced utilization of solar energy. The Nusselt number (Nu), friction factor (f), and thermohydraulic performance enhance about 6.6, 9.4, and 3.06 times, respectively, at attack angle 75o for inline arrangement of DW over the smooth duct. Thermohydraulic performance of reversed‐flow SAH is compared with previously published works, and it highlights that the full‐length inline and staggered arrangement of the DW offers the most significant improvements in heat transfer and friction factor.

energy & fuels
Energetic, exergetic and enviro-economic analysis of parallel pass jet plate solar air heater with artificial roughness

M. M. Matheswaran,T. V. Arjunan,D. Somasundaram

DOI: https://doi.org/10.1007/s10973-018-7727-4

IF: 4.755

2018-09-18

Journal of Thermal Analysis and Calorimetry

Abstract:In this work, the thermal performance of single-pass double-duct jet plate solar air heater with various designs of artificial roughness is analyzed by developing a mathematical model. The influence of artificial roughness designs on the performance of the solar air heater is analyzed based on energy and exergy basis, and the results are compared with single-pass single-duct jet plate solar air heater. Further, year-around enviro-economic analysis is carried out for artificial roughness design providing the better performance. The results show that single-pass double-duct jet plate solar air heater with arc-shaped rib roughness produces highest energetic and exergetic efficiency. The results are compared with single-pass single-duct jet plate solar air heater in the form of energetic and exergetic efficiency enhancement ratios, annual overall energy and exergy gain and amount of carbon credit earned. The mathematical model has been validated with analytical and experimental results available in the literature with acceptable deviation. On the basis of numerical calculations, it has been concluded that single-pass double-duct jet plate solar air heater improves annual usual energy and exergy gain by 111.7% and 185.6%, respectively. Further, it reduces 2.11 times of production of CO2 mitigation per year and enhances the revenue of annual carbon credit by 2.85 times.

chemistry, physical, analytical,thermodynamics
An experimental investigation of the performance of new design of solar air heater (tubular)

Hamdy Hassan,Saleh Abo-Elfadl,M.F. El-Dosoky

DOI: https://doi.org/10.1016/j.renene.2019.11.112

IF: 8.7

2020-05-01

Renewable Energy

Abstract:An experimental work on the performance of new design of solar air heater (SAH) called tubular solar heater (TSAH) is investigated experimentally. In this design, the flat absorber plate of the flat solar air heater (FSAH) is replaced by adjacent tubes at the same direction of the airflow through the SAH. Two SAHs (FSAH and TSAH) having the same dimensions and materials except their absorbers are constructed to compare their performance at different airflow rates through the SAHs. Results reveal that the TSAH has higher efficiency, output power, and outlet air temperature and lower top heat loss compared to FSAH. Moreover, it is found that the efficiency of the presented TSAH is greater than the efficiency of the studied previous SAHs designs. TSAH achieves a maximum rise of 13.2 °C for the outlet air temperature from the SAH compared to FSAH at inlet air mass flow rate 0.025 kg/s to the SAHs. The average daily TSAH efficiency is about 83.6%, 76.3% and 59.8% at air mass flow rate 0.075, 0.05 and 0.025 kg/s, respectively with an increase of 132.6%, 58.6%, and 43.5%, respectively compared to FSAH. The daily top heat loss of TSAH decreases by about 10% compared to FSAH.

energy & fuels,green & sustainable science & technology
Heat transfer Enhancement of Impinging Jet-Corrugated Solar Air Heaters

Aneeq Raheem,Waseem Siddique,Khalid Waheed,Imran Aziz,Irfan Javed,Muhammad Numan Iqbal,Tareq Salameh,Kamran Qureshi,Numan Iqbal

DOI: https://doi.org/10.1115/1.4064503

2024-01-16

Journal of Solar Energy Engineering

Abstract:Abstract Solar Air Heater (SAH) is one of many applications of solar energy, but it has low thermal performance. To cater to this issue, a novel corrugated jet-impinging channel has been proposed for the absorbing plate of SAHs. The Nusselt number, pressure loss pumping power, and friction factor were computed by experimental and numerical studies for three different arrangements of jets i.e., 1×1 square, 2×2, and 3×3 jet array with three target plates i.e., smooth, trapezoidal, and sinusoidal corrugated plates over the Reynolds number range of 1740–2700 and jet-to-target plate spacing of 5.1–14.6. It was observed that jet-to-target plate distance and multiple jets impinging can affect the heat transfer enhancement significantly. An optimization study has been performed using the statistical Taguchi method. The optimum value of Nusselt number was found for the trapezoidal corrugated target plate, with 3×3 multiple jet impingement, jet-to-target plate distance of 5.1, and Reynolds number value of 2700 while the optimum value of friction factor was found for 3×3 jet impingement. CFD and experimental data are found to be in good agreement. An increase of 11 times was observed in Thermal Performance Factor as compared to the base case. Trapezoidal corrugation seems to be the effective profile for SAHs.

energy & fuels,engineering, mechanical
Role of Artificial Roughness in the Performance Improvement of Solar Air Heaters

Navneet Arya,Rajneesh Kumar,Varun Goel

DOI: https://doi.org/10.1007/978-981-16-2648-7_23

2021-08-08

Abstract:Solar radiation is a free, abundant, and clean source of thermal energy. A solar air heater (SAH) is a simple device which acts as a heat exchanger in a way that it extracts thermal energy from the solar radiation. There are various applications in which SAH is used such as space heating and crop drying. As the performance of SAH is low due to less heat transfer coefficient of air which acts as a working fluid in SAHs. Among different techniques, artificial roughness is considered to be the best technique for improving the performance of SAH. Providing roughness element in the direction of flow will help in creating local turbulence which helps in augmenting the heat transfer. Due to increase in turbulence, friction also increases in the flow channel. So, roughness may be provided in such a manner that no significant rise in friction takes place. A lot of roughness geometries were investigated experimentally, numerically to see the impact of roughness elements on heat transfer and friction. The impact of roughness elements on the performance of SAH has been studied for roughness geometry using computational fluid dynamics (CFD). It is a powerful numerical tool which can be utilized to study the flow structure near roughness elements in solar air heaters. This chapter provides the comprehensive information about the different cross-sectional roughness elements, and the effect of these roughness elements on the performance of SAH has also been discussed.
Heat transfer performance and flow characteristics of solar air heaters with inclined trapezoidal vortex generators

Hui Xiao,Zhimin Dong,Zhichun Liu,Wei Liu

DOI: https://doi.org/10.1016/j.applthermaleng.2020.115484

IF: 6.4

2020-10-01

Applied Thermal Engineering

Abstract:Solar air heaters (SAHs) are widely used devices for solar energy utilization at low temperature. The low convective heat transfer performance limits the energy conversion efficiency. This paper was aimed at investigating the flow characteristics and heat transfer enhancement mechanism, thermal hydraulic performance, and energy conversion efficiency of the SAH fitted with novel inclined trapezoidal vortex generators (ITVGs). The heat transfer performance and flow characteristics of a simplified unit were obtained by numerical simulation. A pair of longitudinal swirls were found close to both sides of each ITVG and the shape of vortex was rectangular in the front view. In the range of this paper, the order of overall thermal hydraulic performance for four different arrangements was listed as: upwind aligned (A1) > mixed staggered (A4) > upwind staggered (A2) > downwind aligned (A3). Furthermore, the A1 arrangement was applied to study the thermal hydraulic performance by altering parameters b/pt, e/H, and pl/H with Reynolds number ranging from 6000 to 18000. The range of Nu/Nu0, f/f0, EEC, and R3 were 1.24-3.71, 1.39-11.8, 0.26-0.98 and 1.11-1.89, respectively. On this basis, energy and exergy efficiency evaluations were carried out on the practical SAH integrated by sixteen basic units. The energy efficiency and exergy efficiency could be maximally enhanced by 24% and 31% compared with the smooth SAH, respectively.

energy & fuels,engineering, mechanical,thermodynamics,mechanics
Enhanced performance assessment of an integrated evacuated tube and flat plate collector solar air heater with thermal storage material

Magda K. El-Fakharany,Aly-Eldeen A. Abo-Samra,A.M. Abdelmaqsoud,S.A. Marzouk

DOI: https://doi.org/10.1016/j.applthermaleng.2024.122653

IF: 6.4

2024-04-01

Applied Thermal Engineering

Abstract:The solar air heater incorporating flat plate solar collectors is a straightforward system suitable for domestic use. Nonetheless, it faces challenges with lower thermal efficiency, especially when applied to moderate-temperature purposes. This study aimed to enhance the solar air heater performance by integrating an evacuated tube collector with a flat plate collector and incorporating paraffin C20-C33 as thermal storage material. Inside the flat plate solar collector, the phase change material (paraffin C20-C33) is placed under the absorber surface where the copper air pipes are immersed. Different parameters like outlet temperature, temperature rise, heat gain, thermal efficiency, and pressure drop have been analyzed and discussed for varying weather conditions and mass air flow rates. Also, the system performance is compared by using phase change material (paraffin C20-C33) and without it. The experimental results show that the innovative design achieves higher efficiency, temperature output, and operation hours compared to the standard SAHs. In the presented SAH, the maximum air outlet temperature reached 119 °C at a flow rate of 0.015 kg/s. The maximum ratios of temperature rise to solar radiation at mass air flow rates 0.015, 0.02, and 0.025 kg/s were about 28 %, 26 %, and 25.5 % without PCM and 31 %, 28.5 %, and 27.6 % with PCM, respectively. The average daily thermal efficiency reached the highest values of 47.46 %, 56.12 %, and 64.53 % at air mass flow rates of 0.015, 0.02, and 0.025 kg/s respectively with PCM. The increase in the ratio of accumulated useful energy to average solar radiation through the day was found at 16 %, 14 %, and 13 % with PCM at 0.015, 0.02, and 0.025 kg/s respectively compared to the one without PCM. This developed solar air heater shows promising potential for various applications such as drying and industrial process heating.

energy & fuels,engineering, mechanical,thermodynamics,mechanics

Group B streptococcal cellulitis-adenitis in a previously normal child.

Experimental study on the thermal performance of a solar air heater integrated with multi-geometry arrangements over the absorber plate

Investigation on energy, economic, and environmental aspects of double-pass solar air heater

Experimental analysis of a solar air heater using waste mild steel chips as a sensible heat storage material

Energy and exergy experimental analysis for innovative finned plate solar air heater

Gastrointestinal hormones: environmental cues for Fasciola hepatica?

Numerical analysis of a solar air heater with offset transverse ribs placed near the absorber plate

Effect of the baffle's type on thermal performance of solar air heaters

Impact of corrugated duct and heat storage element on the performance of a low-cost solar air heater under forced air circulation: an experimental study

Thermal performance evaluation of a solar air heater integrated with helical tubes carrying phase change material

Experimental Study of the Effect of Porous Media on the Performance of Single-Pass Solar Air Heater

Dialysis search filters for PubMed, Ovid MEDLINE, and Embase databases.

Thermal Performance Factor of Impinging Jet‐Angled Corrugated Solar Air Heaters

Analysis of solar air heaters based on computational fluid dynamics

Experimental Study of Reverse Flow Solar Air Heater Having Perforation and Delta Wing on Absorber Plate

Energetic, exergetic and enviro-economic analysis of parallel pass jet plate solar air heater with artificial roughness

An experimental investigation of the performance of new design of solar air heater (tubular)

Heat transfer Enhancement of Impinging Jet-Corrugated Solar Air Heaters

Role of Artificial Roughness in the Performance Improvement of Solar Air Heaters

Heat transfer performance and flow characteristics of solar air heaters with inclined trapezoidal vortex generators

Enhanced performance assessment of an integrated evacuated tube and flat plate collector solar air heater with thermal storage material