Failure to diagnose anemia in medical inpatients.

A. Karnad,J. Dilorio,J. Wright

DOI: https://doi.org/10.1016/0002-9343(87)90029-5

1987-04-01

Abstract:

What problem does this paper attempt to address?

Thermoelectric Properties of Topological Insulator Lanthanum Phosphide Via First-Principles Study

Yu Zhou,Wang-Li Tao,Zhao-Yi Zeng,Xiang-Rong Chen,Qi-Feng Chen

DOI: https://doi.org/10.1063/1.5043170

IF: 2.877

2019-01-01

Journal of Applied Physics

Abstract:We systematically investigate the thermoelectric properties of lanthanum phosphide (LaP) using first-principles calculations together with the Boltzmann transport theory. The dynamic stability of LaP is confirmed based on phonon dispersion. The different atomic masses of La and P atoms lead to an acoustic-optical bandgap that prohibits scattering between acoustic and optical phonon modes. The lattice thermal conductivity κl is 3.19 W/mK at room temperature, which is less than that of LaAs because of the smaller group velocities and the larger Grüneisen parameter. The calculated phonon-mode contribution to κl, scattering rate, and mean free path may provide significant guidance to further theoretical and experimental research. The power factor reaches 0.012 W m−1 K−2 at a carrier concentration of 1.05×1020cm−3, which is comparable to the power factor of the typical thermoelectric material Bi2Te3. This reasonable power factor and thermal conductivity suggest that LaP is a promising thermoelectric material. The dependence of the figure of merit ZT on carrier concentration n and temperature T indicates that a high ZT can be obtained by increasing the temperature and tuning the carrier concentration.
First-Principles Calculations on Thermoelectric Properties of Layered Transition Metal Phosphides MP2 (M = Ni, Pd, Pt)

Heng-yu Yang,Guofeng Xie,Xue-Liang Zhu,Wu-Xing Zhou,Ning Xu

DOI: https://doi.org/10.1007/s11664-021-08774-2

IF: 2.1

2021-02-12

Journal of Electronic Materials

Abstract:Very recently, a stable structure of layered transition metal phosphides MP2 (M = Ni, Pd and Pt) has been discovered. This study reveals that these three materials are semiconductor materials with a direct band gap (0.5–0.85 eV) and also have very high hole and electron mobility. The electron mobility of the PtP2 monolayer is surprisingly as high as 14.4 × 104 cm2 V−1 s−1. Based on their excellent electronic properties, herein we predict the thermoelectric (TE) performance of MP2 monolayers by using first-principles and Boltzmann transport equation. The calculation results show that the single-layer NiP2, PdP2 and PtP2 have low lattice thermal conductivity 7.6 W m−1 K−1, 9.0 W m−1 K−1 and 17.8 W m−1 K−1 at room temperature, respectively, which is mainly caused by the small phonon group velocity, low relaxation time, high Grüneisen parameter and large phonon scattering phase space. Because of the ultra-high carrier mobility and the highly degenerate band structure, MP2 monolayers have large Seebeck coefficient, and the value of PdP2 reaches up to 283 μV K−1 at 300 K. The good phonon and electrical transport properties give the MP2 monolayers a high TE figure of merit (ZT). The maximum ZT of NiP2 and PdP2 monolayers at 500 K is 1.52 (p-type) and 1.95 (n-type), respectively, and the corresponding concentration of maximum ZT MP2 monolayers is around 1011 cm−2. Overall, our work indicates that the MP2 monolayers are the promising candidates in TE applications.

engineering, electrical & electronic,materials science, multidisciplinary,physics, applied
Exceptional Thermoelectric Performance Enabled by High Carrier Mobility and Intrinsically Low Lattice Thermal Conductivity in Phosphide Cd 3 P 2

Lizhu Fan,Kunling Peng,Zizhen Zhou,Yanci Yan,Chen Ran,Honghui Wang,Guang Han,Bin Zhang,Xu Lu,Guoyu Wang,Xiaoyuan Zhou

DOI: https://doi.org/10.1021/acs.chemmater.1c03619

IF: 10.508

2022-02-10

Chemistry of Materials

Abstract:A novel thermoelectric Cd3P2 is obtained via regulating carrier concentrations. Ultrahigh carrier mobilities over 1500 cm2 V–1 s–1 are observed at room temperature, which is attributed to small band effective mass and confirmed by the electronic structure calculation. Meanwhile, the intrinsically low lattice thermal conductivity below 1.0 W m–1 K–1 in the investigated temperature range is found due to the complex crystal structure and low sound velocity. Combined with high mobility and low thermal conductivity, a peak zT of 0.91 at 673 K and an excellent average zT of 0.57 over 300–673 K are obtained in Cd3P2-based compounds, which are record-high values among phosphides. This study highlights the potential of exploring high-performance novel thermoelectric materials in compounds with high carrier mobility.

materials science, multidisciplinary,chemistry, physical
High Performance Thermoelectric Materials Based on Metal Organic Coordination Polymers Through First‐principles Band Engineering

Jahanzeb Khan,Yunpeng Liu,Tianqi Zhao,Hua Geng,Wei Xu,Zhigang Shuai

DOI: https://doi.org/10.1002/jcc.25639

2018-01-01

Journal of Computational Chemistry

Abstract:Metal organic coordination polymers (MOCPs) provide an intriguing platform to design functional thermoelectric materials through modifying metal atoms, organic ligands, etc. Based on density functional theory (DFT) coupled with Boltzmann transport theory, the thermoelectric properties of several MOCPs, which is designed by intercalating organic linkers ranging from benzene to pentacene between two inorganic units, have been investigated. We found that the interplay of d orbital of Ni atom and π orbitals of the organic linkers play an important role in band engineering and then thermoelectric efficiency. Combining the high conductivity for π orbitals of organic ligands and high Seebeck coefficient of the d orbital of Ni atom, such intercalated MOCPs provide new way to design high performance thermoelectric materials. © 2018 Wiley Periodicals, Inc.
Excellent Thermoelectric Performance in Alkali Metal Phosphides M P (M = Na and K) With Phonon-Glass Electron-Crystal Like Behaviour

Xinji Xu,Weiyu Zhou,Wei Zhan,Ziyi Pan,Hao Huang,Geng Li,Shuming Zeng,Yusong Tu

DOI: https://doi.org/10.1039/d4cp02117g

IF: 3.3

2024-08-26

Physical Chemistry Chemical Physics

Abstract:Identifying ideal thermoelectric materials presents a formidable challenge due to the intricate coupling relationship between thermal conductivity and power factor. Here, based on first-principles calculations, along with self-consistent phonon theory and the Boltzmann transport equation, we theoretically investigate the thermoelectric properties of alkali metal phosphides M P (M = Na and K). The evident 'avoided crossing' phenomenon indicates the phonon glass behavior of M P (M = Na and K). Due to the strong lattice anharmonicity induced by alkali metal elements, accounting for quartic anharmonic corrections, the lattice thermal conductivities of Na P and K P at room temperature are merely 0.25 and 0.12 Wm K , respectively. Furthermore, the high degeneracy and 'pudding-mold-type' band structure lead to high p-type in M P (M = Na and K). At 300 K, the p-type power factors ( ) of Na P and K P can reach 3.90 and 0.80 mW/mK , respectively. The combination of ultralow and high leads to excellent thermoelectric figure of merit ( ) values of 1.70 (3.38) and 1.18 (2.13) for p-type Na P and K P under optimal doping concentration at 300K (500K), respectively, surpassing traditional thermoelectric materials. These findings demonstrate that M P (M = Na and K) exhibits behavior similar to phonon-glass electron crystals, thereby indicating a direction for the search for high-performance thermoelectric materials.

chemistry, physical,physics, atomic, molecular & chemical
Thermoelectric Transport Properties of Metal Phosphide XLiP (X = Sr,Ba).

Xingzhu Yuan,Yinchang Zhao,Jun Ni,Sheng Meng,Zhenhong Dai

DOI: https://doi.org/10.1088/1361-648x/acb983

2023-01-01

Journal of Physics Condensed Matter

Abstract:Metal phosphides are stable and have excellent electrical characteristics, their high thermal conductivity has prevented them from being used as thermoelectric materials. In this paper, the thermoelectric transport properties of XLiP (X = Sr Ba) are investigated on the basis of first-principles calculations, Boltzmann transport equation and self-consistent phonon theory. In addition, we also consider the effect of quartic anharmonicity on the thermal transport properties and lattice dynamics of SrLiP and BaLiP. The strong anharmonicity of the two compounds make the lattice thermal conductivity decrease rapidly with the increase of temperature. At 300 K, the lattice thermal conductivity of SrLiP and BaLiP on the a(b)-axis is only 2.98 and 2.93 Wm−1K−1, respectively. Due to its excellent electron transport properties, it has greater conductivity in the a(b) axis. Finally, due to the energy pocket and anisotropy at the bottom of the conduction band, the n-type maximum ZT values of trapped SrLiP and BaLiP on the a(b) axis are 0.87 and 0.94 at 900 K, respectively. The high thermoelectric performance of both compounds encourages further studies on the thermoelectric properties of metal phosphides.
Enhanced Thermoelectric Efficiency Via Orthogonal Electrical and Thermal Conductances in Phosphorene.

Ruixiang Fei,Alireza Faghaninia,Ryan Soklaski,Jia-An Yan,Cynthia Lo,Li Yang

DOI: https://doi.org/10.1021/nl502865s

IF: 10.8

2014-01-01

Nano Letters

Abstract:Thermoelectric devices that utilize the Seebeck effect convert heat flow into electrical energy and are highly desirable for the development of portable, solid state, passively powered electronic systems. The conversion efficiencies of such devices are quantified by the dimensionless thermoelectric figure of merit (ZT), which is proportional to the ratio of a device's electrical conductance to its thermal conductance. In this paper, a recently fabricated two-dimensional (2D) semiconductor called phosphorene (monolayer black phosphorus) is assessed for its thermoelectric capabilities. First-principles and model calculations reveal not only that phosphorene possesses a spatially anisotropic electrical conductance, but that its lattice thermal conductance exhibits a pronounced spatial-anisotropy as well. The prominent electrical and thermal conducting directions are orthogonal to one another, enhancing the ratio of these conductances. As a result, ZT may reach the criterion for commercial deployment along the armchair direction of phosphorene at T = 500 K and is close to 1 even at room temperature given moderate doping (∼2 × 10(16) m(-2) or 2 × 10(12) cm(-2)). Ultimately, phosphorene hopefully stands out as an environmentally sound thermoelectric material with unprecedented qualities. Intrinsically, it is a mechanically flexible material that converts heat energy with high efficiency at low temperatures (∼300 K), one whose performance does not require any sophisticated engineering techniques.
Strong Electron–Phonon and Phonon–Phonon Interactions Lead to High Thermoelectric Performances in Lead Phosphorene Via Symmetry Breaking

Ao Wu,Yujie Xia,Yiming Zhang,Lei Peng,Hezhu Shao,Yan Cen,Heyuan Zhu,Hao Zhang

DOI: https://doi.org/10.1002/adts.202300226

2023-01-01

Advanced Theory and Simulations

Abstract:Understanding the full electron-phonon and phonon-phonon interaction effects in semiconductors is crucial for tuning electronic and phonon transport properties with the purpose to the enhancement of thermoelectric performances. In this work, based on the detailed investigations on 2D lead phosphorene (PbP) by using the first-principle calculations, it is demonstrated that, in & alpha;-$\alpha -$, & beta;-$\beta -$, and & gamma;-$\gamma -$PbP, the electron-phonon interactions are significantly stronger than conventional group-IV monolayers such as silicene by five orders in magnitude, and intravalley scatterings dominate over the intervalley scattering due to less degenerate band extrema near Fermi level. Based on the selection-rule analysis, it is found that the symmetry breaking in the janus & gamma; phase compared to the higher-symmetry & alpha; phase allows fewer symmetry operations, leading to more allowed scattering channels for electrons and phonons, subsequently suppressing the electron and phonon transport in & gamma;-$\gamma -$PbP. Due to the low Debye temperatures, and strong four-phonon interactions, the lattice thermal conductivities at room temperature in these monolayers are sharply decreased. Finally, it is found that the maximum thermoelectric figure of merits for these three monolayers reach 0.90/0.24/1.25 at room temperature, respectively. This work not only paves the way for the promising applications of PbP monolayers in thermoelectric devices, but also suggests that symmetry breaking and strong high-order phonon-phonon interactions are crucial to identifying excellent thermoelectric materials. The work highlights the dominance of intravalley scattering over intervalley scattering in electron relaxation times. Group theory analysis reveals restrictions on certain phonons in assisting electron transition, resulting in improved carrier mobility in a-PbP. Ultra-low lattice thermal conductivities are observed in PbP monolayers. Promising thermoelectric figure of merit values are predicted for PbP monolayers at room temperature.image
Metal halide thermoelectrics: prediction of high-performance CsCu2I3

Jong Woong Park,Young-Kwang Jung,Aron Walsh

DOI: https://doi.org/10.1103/PRXEnergy.2.043004

2023-05-19

Abstract:Thermoelectric devices can directly convert waste heat into electricity, which makes them an important clean energy technology. The underlying materials performance can be evaluated by the dimensionless figure of merit ZT. Metal halides are attractive candidates due to their chemical flexibility and ease of processing; however, the maximum ZT realized (ZT = 0.15) falls far below the level needed for commercialization (ZT > 1). Using a first-principles procedure we assess the thermoelectric potential of copper halide CsCu2I3, which features 1D Cu-I connectivity. The n-type crystal is predicted to exhibit a maximum ZT of 2.2 at 600 K along the b-axis. The strong phonon anharmonicity of this system is shown by locally stable non-centrosymmetric Amm2 structures that are averaged to form the observed centrosymmetric Cmcm space group. Our work provides insights into the structure-property relations in metal halide thermoelectrics and suggests a path forward to engineer higher-performance heat-to-electricity conversion.

Materials Science,Computational Physics
Prediction of the High Thermoelectric Performance of Pnictogen Dichalcogenide Layered Compounds with Quasi-One-Dimensional Gapped Dirac-like Band Dispersion

Masayuki Ochi,Hidetomo Usui,Kazuhiko Kuroki

DOI: https://doi.org/10.1103/PhysRevApplied.8.064020

2017-12-20

Abstract:Thermoelectric power generation has been recognized as one of the most important technologies, and high-performance thermoelectric materials have long been pursued. However, because of the large number of candidate materials, this quest is extremely challenging, and it has become clear that a firm theoretical concept from the viewpoint of band-structure engineering is needed. In this study, we theoretically demonstrate that pnictogen-dichalcogenide layered compounds, which originally attracted attention as a family of superconductors and have recently been investigated as thermoelectric materials, can exhibit very high thermoelectric performance with elemental substitution. In particular, we clarify a promising guiding principle for materials design and find that LaOAsSe$_2$, a material that has yet to be synthesized, has a powerfactor that is six times as large as that of the known compound LaOBiS$_2$ and can exhibit a very large $ZT$ under some plausible assumptions. This large enhancement of the thermoelectric performance originates from the quasi-one-dimensional gapped Dirac-like band dispersion, which is realized by the square-lattice network. Our study offers one ideal limit of the band structure for thermoelectric materials. Because our target materials have high controllability of constituent elements and feasibility of carrier doping, experimental studies along this line are strongly awaited.

Materials Science
Electronic structure and thermoelectric prospects of phosphide skutterudites

Marco Fornari,David J. Singh

DOI: https://doi.org/10.1103/physrevb.59.9722

IF: 3.7

1999-04-15

Physical Review B

Abstract:The prospects for high thermoelectric performance in phosphide skutterudites are investigated based on first-principles calculations. We find that stoichiometric CoP3 differs from the corresponding arsenide and antimonide in that it is metallic. As such, the band structure must be modified if high thermopowers are to be achieved. In analogy to the antimonides it is expected that this may be done by filling with La. Calculations for LaFe4P12 show that a gap can in fact be opened by La filling, but that the valence band is too light to yield reasonable p-type thermopowers at appropriate carrier densities; n-type La-filled material may be more favorable.

physics, condensed matter, applied,materials science, multidisciplinary
Achieving ZT > 1 in Cu and Ga Co-doped Ag 6 Ge 10 P 12 with Superior Mechanical Performance and Its Fundamental Physical Properties toward Practical Thermoelectric Device Applications

Hiromasa Namiki,Masahiro Kobayashi,Yasuhiro Nishikawa,Yumiko Miyake,Masashi Sasaki,Naoki Tachibana

DOI: https://doi.org/10.1021/acsami.4c12963

IF: 9.5

2024-10-02

ACS Applied Materials & Interfaces

Abstract:Recently, phosphorus-based compounds have emerged as potential candidates for thermoelectric materials. One of the key challenges facing this field is to achieve ZT > 1, which is the benchmark for thermoelectric device applications. In this study, it is demonstrated that the thermoelectric performance of environmentally friendly Ag(6)Ge(10)P(12) is enhanced by co-doping Cu and Ga. The mechanical properties, coefficient of linear thermal expansion, work function, and compatibility factor are...

materials science, multidisciplinary,nanoscience & nanotechnology
Room Temperature High Thermoelectric Performance of Bi-based Full-Heusler Compounds Cs Rb3−xBi with Strong Anharmonicity

Shuming Zeng,Qian Shen,Lei Fang,Zonglin Gu,Jinpeng Yang,Geng Li,Yusong Tu,Jun Ni

DOI: https://doi.org/10.1016/j.ijheatmasstransfer.2023.124628

IF: 5.2

2023-01-01

International Journal of Heat and Mass Transfer

Abstract:Bismuth-based compounds have been identified as a class of promising candidates for the realization of high-performance thermoelectrics, derived from their exceptional electrical conductivity and intrinsic low lattice thermal conductivity κL. Here, we employed first-principles calculations, self-consistent phonon theory, and compressive sensing technique in conjunction with the Boltzmann transport equation to investigate the anharmonic thermoelectric properties of full-heusler bismuth compounds CsxRb3−xBi. As the Cs content increases, the κL of CsxRb3−xBi decreases due to impurity scattering effects, and then increases. Among them, at 300 K, Rb3Bi has the largest κL of 0.69 Wm−1K−1, while Cs2RbBi has the smallest κL of 0.45 Wm−1K−1, both of which are lower than the κL of traditional bismuth-based thermoelectric materials. The ultralow κL originates from the strong lattice anharmonicity. In addition, the coexistence of high dispersion and flat band edges leads to high thermoelectric power factor at optimal doping concentration. As a result, the largest thermoelectric figure of merit ZT values of 2.59 (4.19) at 300 (500) K were obtained for CsRb2Bi at optimal hole doping level. These findings suggest that CsxRb3−xBi compounds are superior for thermal management and thermoelectric applications.
Two-dimensional metal-organic frameworks with high thermoelectric efficiency through metal ion selection

Yuping He,Catalin D Spataru,Francois Léonard,Reese E Jones,Michael E Foster,Mark D Allendorf,A Alec Talin

DOI: https://doi.org/10.1039/c7cp03310a

2017-07-26

Abstract:Two-dimensional (2D) materials have attracted much attention due to their novel properties. An exciting new class of 2D materials based on metal-organic frameworks (MOFs) has recently emerged, displaying high electrical conductivity, a rarity among organic nanoporous materials. The emergence of these materials raises intriguing questions about their fundamental electronic, optical, and thermal properties, but few studies exist in this regard. Here we present an atomistic study of the thermoelectric properties of crystalline 2D MOFs X3(HITP)2 with X = Ni, Pd or Pt, and HITP = 2,3,6,7,10,11-hexaiminotriphenylene, using both ab initio transport models and classical molecular dynamics simulations. We find that these materials have a high Seebeck coefficient and low thermal conductivity, making them promising for thermoelectric applications. Furthermore, we explore the dependence of thermoelectric transport properties on the atomic structure by comparing the calculated band structure, band alignment, and electronic density of states of the three 2D MOFs, and find that the thermoelectric transport properties strongly depend on both the interaction between the ligands and the metal ions, and the d orbital splitting of the metal ions induced by the ligands. This demonstrates that selection of the metal ion is a powerful approach to control and enhance the thermoelectric properties. Interestingly we reveal an unexpected effect where, unlike for electrons, the thermal and electrical current may not be equally carried by the holes, leading to a significant deviation from the Wiedemann-Franz law. The results of this work provide fundamental guidance to optimize the existing 2D MOFs, and to design and discover new families of MOF-like materials for thermoelectric applications.
High Thermoelectric Performance of a Novel Γ-Pbsnx2 (X = S, Se, Te) Monolayer: Predicted Using First Principles

Changhao Ding,Zhifu Duan,Nannan Luo,Jiang Zeng,Wei Ren,Liming Tang,Keqiu Chen

DOI: https://doi.org/10.3390/nano13091519

IF: 5.3

2023-01-01

Nanomaterials

Abstract:Two-dimensional (2D) group IV metal chalcogenides are potential candidates for thermoelectric (TE) applications due to their unique structural properties. In this paper, we predicted a 2D monolayer group IV metal chalcogenide semiconductor γ-PbSn2 (X = S, Se, Te), and first-principles calculations and Boltzmann transport theory were used to study the thermoelectric performance. We found that γ-PbSnX2 had an ultra-high carrier mobility of up to 4.04 × 103 cm2 V−1 s−1, which produced metal-like electrical conductivity. Moreover, γ-PbSn2 not only has a very high Seebeck coefficient, which leads to a high power factor, but also shows an intrinsically low lattice thermal conductivity of 6–8 W/mK at room temperature. The lower lattice thermal conductivity and high power factors resulted in excellent thermoelectric performance. The ZT values of γ-PbSnS2 and γ-PbSnSe2 were as high as 2.65 and 2.96 at 900 K, respectively. The result suggests that the γ-PbSnX2 monolayer is a better candidates for excellent thermoelectric performance.
First‐Principles Study of the Effects of High‐Order Anharmonicity on the Thermal Transport Properties and Thermoelectric Effects in the Lattice Dynamics of 12 New Full–Heusler Compounds X2YTe (X = Na, K, Rb, Cs; Y = Zn, Cd, Hg)

Yue Wang,Yinchang Zhao,Jun Ni,Zhenhong Dai

DOI: https://doi.org/10.1002/adfm.202410983

IF: 19

2024-10-18

Advanced Functional Materials

Abstract:First‐principles calculations are employed to investigate 12 Full–Heusler compounds X2YTe. The results showed that anharmonicity decreases with increasing X atom mass, while for Y atoms, the trend is reversed. This suggests a competition between and SRs. Introducing higher‐order anharmonicity explained this anomaly, allowing us to deduce the 4ph SRs intensity across the materials. This led to extremely low κL. With the naturally high PF of Full–Heusler compounds, we achieved groundbreaking results, surpassing the long‐standing ZT value limit of 3. In this study, advanced first‐principles calculations combined with self‐consistent phonon theory and the Boltzmann transport equation are used to assess the thermoelectric properties of novel Full–Heusler materials X2YTe (X = Na, K, Rb, Cs; Y = Zn, Cd, Hg). These materials exhibit low formation energies, facilitating synthesis under standard conditions. This analysis showed that lattice anharmonicity increases with the atomic mass of X and decreases with the atomic mass of Y due to the rattling effect of Y atoms. Significant rattling effects are identified, prompting the inclusion of higher‐order anharmonic effects. By renormalizing the phonon spectrum and accounting for three‐phonon and four‐phonon scattering, the mechanisms behind the low lattice thermal conductivity in these compounds is uncovered. The combination of low lattice thermal conductivity and high power factors resulted in remarkable thermoelectric figure of merit values at optimal doping concentrations and temperatures. Notably, except for Na2ZnTe and Na2HgTe, all other materials surpassed the long‐standing figure of merit record of less than 3, with Rb2ZnTe achieving a figure of merit of 8.11 at 700 K with an n‐type doping concentration of 2 × 1019. The inclusion of spin‐orbit coupling led to less than a 10% reduction in the thermoelectric figure of merit, underscoring the superior thermoelectric performance of these materials.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Potential thermoelectric materials $\mathrm{CsMI_3}$ (M=Sn and Pb) in perovskite structures from the first-principles calculations

San-Dong Guo,Jian-Li Wang

DOI: https://doi.org/10.48550/arXiv.1605.08886

2016-05-28

Abstract:The thermoelectric properties of halide perovskites $\mathrm{CsMI_3}$ (M=Sn and Pb) are investigated from a combination of first-principles calculations and semiclassical Boltzmann transport theory by considering both the electron and phonon transport. The electronic part is performed using a modified Becke and Johnson (mBJ) exchange potential, including spin-orbit coupling (SOC), while the phonon part is computed using generalized gradient approximation (GGA). It is found that SOC has remarkable detrimental effect on n-type power factor, while has a negligible influence in p-type doping, which can be explained by considering SOC effect on conduction and valence bands. Calculated results show exceptionally low lattice thermal conductivities in $\mathrm{CsSnI_3}$ and $\mathrm{CsPbI_3}$, and the corresponding room-temperature lattice thermal conductivity is 0.54 $\mathrm{W m^{-1} K^{-1}}$ and 0.25 $\mathrm{W m^{-1} K^{-1}}$. At 1000 K, the maximal figure of merit $ZT$ is up to 0.63 and 0.64 for $\mathrm{CsSnI_3}$ and $\mathrm{CsPbI_3}$ with scattering time $\tau$=$10^{-14}$ s, and the peak $ZT$ is 0.49 and 0.41 with $\tau$=$10^{-15}$ s. These results make us believe that $\mathrm{CsMI_3}$ (M=Sn and Pb) in perovskite structures may be potential thermoelectric materials.

Materials Science
Chemical trends in the high thermoelectric performance of the pyrite-type dichalcogenides: ZnS2, CdS2 and CdSe2

Tiantian Jia,Jesús Carrete,Georg K.H. Madsen,Yongsheng Zhang,Suhuai Wei

DOI: https://doi.org/10.48550/arXiv.2005.05916

2022-03-07

Abstract:The thermoelectric properties of the three pyrite-type IIB-VIA2 dichalcogenides (ZnS2, CdS2 and CdSe2) are systematically investigated and compared with those of the prototype ZnSe2 in order to optimize their thermoelectric properties. Using the phonon Boltzmann transport equation, we find that they all have ultralow lattice thermal conductivities. By analyzing their vibrational properties, these are attributed to soft phonon modes derived from the loosely bound rattling-like metal atoms and to strong anharmonicities caused by the vibrations of all atoms perpendicular to the strongly bound nonmetallic dimers. Additionally, by correlating those properties along the series, we elucidate a number of chemical trends. We find that heavier atom masses, larger atomic displacement parameters and longer bond lengths between metal and nonmetal atoms can be beneficial to the looser rattling of the metal atoms and therefore lead to softer phonon modes, and that stronger nonmetallic dimer bonds can boost the anharmonicities, both leading to lower thermal conductivities. Furthermore, we find that all three compounds have complex energy isosurfaces at valence and conduction band edges that simultaneously allow for large density-of-states effective masses and small conductivity effective masses for both p-type and n-type carriers. Consequently, the calculated thermoelectric figures of merit (ZT), can reach large values both for p-type and n-type doping. Our study illustrates the effects of rattling-like metal atoms and localized nonmetallic dimers on the thermal transport properties and the importance of different carrier effective masses to electrical transport properties in these pyrite-type dichalcogenides, which can be used to predict and optimize the thermoelectric properties of other thermoelectric compounds in the future.

Applied Physics,Materials Science
Two-dimensional Mo1-xB2 with ordered metal vacancies obtained for advanced thermoelectric applications based on first-principles calculations

Jie Pu,Ziyu Hu,Xiaohong Shao

DOI: https://doi.org/10.1039/d4cp00319e

IF: 3.3

2024-05-05

Physical Chemistry Chemical Physics

Abstract:The study and development of high thermoelectric properties is crucial for the next generation of microelectronic and wearable electronics. Derived from the recently experimental realization layers in transition metal molybdenum and boride, we report the theoretical realization of advanced thermoelectric properties in two-dimensional (2D) transition metal borides Mo1-xB2 (x=0, 0.05, 0.10, 0.125, 0.15)-based defects sheets. The introducing of metal vacancies results in stronger d-p exchange interactions and hybridization between the Mo-d and B-p atoms. Meanwhile, the ordered metal vacancies enabled transition metal borides (n-type Mo0.9B2) widening the d-bandwidth and rising the d-band center, leading to a relatively high carrier mobility of 3262 cm2V−1s−1 and the twice conductivity greater than bug free n-type MoB2 layer, which indicates that of presenting good electronic and thermal transport properties. Further, the thermoelectric performance investigations exhibit that the maximum ZT up to 3.29, which is superior to currently reported 2D materials. The modulation of defect engineering suggests that the 2D transition metal boride sheets with ordered metal vacancies have promising applications in microelectronics, wearable electronics and thermoelectric devices.

chemistry, physical,physics, atomic, molecular & chemical
First-Principles Thermoelectric Study of SrMgSi and CaMgGe Zintl-Phase Compounds

Jinfeng Yang,Zhaoyu Yang,Xiaonan Wang,Yuxiang Chen,Yongze Xu,Bo Zou,Yuli Yan,Huarui Sun

DOI: https://doi.org/10.1021/acsaem.3c01260

IF: 6.4

2023-07-20

ACS Applied Energy Materials

Abstract:Zintl-phase semiconductor materials with low intrinsic lattice thermal conductivity have been the target of study for thermoelectric (TE) applications. Herein, we report Zintl-phase TiNiSi-type SrMgSi and CaMgGe with calculated low intrinsic lattice thermal conductivity (κL) values of 2.52 and 1.90 W/m·K at room temperature, respectively. The low κL is mainly due to the strong lattice anharmonicity, which originates from the weak bonding of cations in the anionic network, and strong optical-acoustic phonon coupling. Additionally, the high band degeneracy results in good electrical properties, and excellent ZT values of ∼2.83 (n-type, 500 K) and 3.09 (n-type, 500 K) are predicted for SrMgSi and CaMgGe, respectively. The theoretical study provides a valuable direction for exploring Zintl-phase materials for efficient TE power conversion.

materials science, multidisciplinary,chemistry, physical,energy & fuels

Failure to diagnose anemia in medical inpatients.

Thermoelectric Properties of Topological Insulator Lanthanum Phosphide Via First-Principles Study

First-Principles Calculations on Thermoelectric Properties of Layered Transition Metal Phosphides MP2 (M = Ni, Pd, Pt)

Exceptional Thermoelectric Performance Enabled by High Carrier Mobility and Intrinsically Low Lattice Thermal Conductivity in Phosphide Cd 3 P 2

High Performance Thermoelectric Materials Based on Metal Organic Coordination Polymers Through First‐principles Band Engineering

Excellent Thermoelectric Performance in Alkali Metal Phosphides M P (M = Na and K) With Phonon-Glass Electron-Crystal Like Behaviour

Thermoelectric Transport Properties of Metal Phosphide XLiP (X = Sr,Ba).

Enhanced Thermoelectric Efficiency Via Orthogonal Electrical and Thermal Conductances in Phosphorene.

Strong Electron–Phonon and Phonon–Phonon Interactions Lead to High Thermoelectric Performances in Lead Phosphorene Via Symmetry Breaking

Metal halide thermoelectrics: prediction of high-performance CsCu2I3

Prediction of the High Thermoelectric Performance of Pnictogen Dichalcogenide Layered Compounds with Quasi-One-Dimensional Gapped Dirac-like Band Dispersion

Electronic structure and thermoelectric prospects of phosphide skutterudites

Achieving ZT > 1 in Cu and Ga Co-doped Ag 6 Ge 10 P 12 with Superior Mechanical Performance and Its Fundamental Physical Properties toward Practical Thermoelectric Device Applications

Room Temperature High Thermoelectric Performance of Bi-based Full-Heusler Compounds Cs Rb3−xBi with Strong Anharmonicity

Two-dimensional metal-organic frameworks with high thermoelectric efficiency through metal ion selection

High Thermoelectric Performance of a Novel Γ-Pbsnx2 (X = S, Se, Te) Monolayer: Predicted Using First Principles

First‐Principles Study of the Effects of High‐Order Anharmonicity on the Thermal Transport Properties and Thermoelectric Effects in the Lattice Dynamics of 12 New Full–Heusler Compounds X2YTe (X = Na, K, Rb, Cs; Y = Zn, Cd, Hg)

Potential thermoelectric materials $\mathrm{CsMI_3}$ (M=Sn and Pb) in perovskite structures from the first-principles calculations

Chemical trends in the high thermoelectric performance of the pyrite-type dichalcogenides: ZnS2, CdS2 and CdSe2

Two-dimensional Mo1-xB2 with ordered metal vacancies obtained for advanced thermoelectric applications based on first-principles calculations

First-Principles Thermoelectric Study of SrMgSi and CaMgGe Zintl-Phase Compounds