Opioids at Cape Cod

B. Cox

DOI: https://doi.org/10.1038/298790A0

IF: 64.8

1982-08-26

Nature

Abstract:

What problem does this paper attempt to address?

Composition of the dissolved organic matter produced during in situ burning of spilled oil

Aprami Jaggi,Jagoš R. Radović,Lloyd R. Snowdon,Stephen R. Larter,Thomas B.P. Oldenburg

DOI: https://doi.org/10.1016/j.orggeochem.2019.103926

IF: 3.623

2019-12-01

Organic Geochemistry

Abstract:In situ burning is often used as a response method for oil slicks in the marine environment. This process however forms viscous tar-like residues that either float on the surface or sink through the water column, introducing organic species into the water phase. The interaction of this burn residue with the water phase also introduces dissolved organics into the water column. In this study, we conducted laboratory-scale experiments to characterize and compare the organic species entering the water phase from the petrogenic (fresh oil) and pyrogenic (burnt oil) input during oil spills. The oil and water-soluble organics were characterized using ultra-high-resolution mass spectrometry (FTICR-MS). The results show that burning strongly increases concentrations of oil-related constituents entering the water phase, due to transformation reactions producing oxidized organic species with higher water solubility. The pyrogenic water-soluble organics also showed a higher percentage of unsaturated compounds relative to the petrogenic fraction. The effect of these highly unsaturated and oxygenated organic species on oil spill fate and their ecosystem impacts is currently unknown.
Impact of wind on in-situ burning behavior of spilled oil on open water

Depeng Kong,Hanbing Yang,Xu He

DOI: https://doi.org/10.1016/j.jlp.2020.104147

IF: 3.916

2020-05-01

Journal of Loss Prevention in the Process Industries

Abstract:Spilled oil may cause serious environmental pollution and ecological destruction. Thus, an efficient oil spill response is essential to reduce and minimize the impacts seen from an oil spill. In-situ burning (ISB) has been proven to be one of the most convenient and efficient treatment methods for oil spills on sea. When in-situ burning operation is carried out on sea, the wind is usually available. Spilled oil pool fire flame will be blown to tilt with an angle from the vertical direction and the flame length will be stretched. This effect of flame on downstream will be significantly enhanced. It may even cause the burning of spilled oil out of control or hazard the operators near site. Therefore, it is meaningful to study the burning behavior of oil pool fire on open water under wind.A small-scale oil pool fire on open water experiment system was designed, which could simulate the boundary conditions of sea surface ISB. A series of experiments were carried out to study the effects of oil pool diameter, oil layer thickness and wind speed on fire flame length and flame tilt angle. Flame characteristics and temperature of burning system were recorded. This study observes burning behavior to evolve from short pool fire to long declining phase which transient through boilover stage. Dimensionless flame length in pool fire stage increases with wind speed. As expected the flame tilt is strongly influenced by wind speed, tilt angle increase with wind speed. The observed experimental behavior is captured as improvement in the flame length and flame tilt angle models.This study helped better understanding fire behavior in evolving environmental conditions, and the most importantly developed model would help guide better assessment of fire mitigation strategies.

engineering, chemical
Occupational exposure to air pollutants emitted from in situ burning of offshore oil spills: a large-scale field study

Marta Szwangruber,Ingrid Gjesteland,Bjørg Eli Hollund,Liv-Guri Faksness,Ingrid Christina Taban,Frode Engen,Jan Willie Holbu,Hilde Dolva,Magne Bråtveit

DOI: https://doi.org/10.5603/IMH.2022.0001

Abstract:Background: In-situ burning (ISB) could be an effective cleanup method during spills. This study aims to study occupational exposure to pollutants emitted from offshore, large-scale ISB-experiments among personnel on vessels involved in ISB. Materials and methods: Six experimental ISBs after release of 4.2-6 m3 crude or refined oils were performed. Air measurements on three vessels were taken of particulate matter (PM) of different size fractions, polycyclic aromatic hydrocarbons (PAH) and volatile organic compounds (VOC). Results: One vessel was located upwind (about 80-140 m) from the burning oil while two work boats were positioned 200-400 m downwind. One of the work boats moved back and forth transverse to the smoke plume while the other followed the edge of the smoke plume downwind. During the burn period (28-63 min) the range of mean concentrations of PM2.5 particles in the closest work boat downwind from the burn (0.068-0.616 mg/m3) was considerably higher than in the upwind vessel (0.0198-0.029 mg/m3) and in the work boat moving downwind at the edge of the visible smoke (0.007-0.078 mg/m3). The particles were mainly in the PM<1 fraction. In the work boat closest to the burn the mean concentration of particulate PAH and VOC was 0.046-0.070 ng/m3 and < limit of detection -17.1 ppm, respectively. Conclusions: The mean PM2.5 levels in the closest vessel varied between 4 and 41 times higher than the 24-hour Norwegian Air Quality Criteria for the general population, indicating that the particulate exposure may impose a health risk for personnel up to 400 m downwind from an ISB. Exposure to VOC and PAH among crew on board vessels both upwind and downwind from the burning was low during these conditions. However, it is recommended that crew on vessels close to and downwind of smoke plumes from oil fires should use half-masks with P3 filters.
MESOSCALE EXPERIMENTS HELP TO EVALUATE IN-SITU BURNING OF OIL SPILLS1

David D. Evans,William D. Walton,Howard R. Baum,Kathy A. Notarianni,Edward J. Tennyson,Peter A. Tebeau

DOI: https://doi.org/10.7901/2169-3358-1993-1-755

1993-03-01

International Oil Spill Conference Proceedings

Abstract:ABSTRACT Burning of spilled oil has distinct advantages over other cleanup countermeasures. It offers the potential to convert rapidly large quantities of oil into its primary combustion products, carbon dioxide and water, with a small percentage of other unburned and residue byproducts. Disadvantages include the dispersal of the combustion products into the air. Mesoscale and laboratory experiments have been conducted to measure the burning characteristics of crude oil fires. Measurements on crude oil pool fires from 0.4 m to 17.2 m in effective diameter were made to obtain data on the rate of burning, heat release rate, composition of the combustion products, and downwind dispersion of the products. The smaller experiments were performed in laboratories at the National Institute of Standards and Technology and the Fire Research Institute in Japan; and the larger ones at the U. S. Coast Guard Fire Safety and Test Detachment in Mobile, Alabama. From these experiments, the value for surface regression rate of a burning crude oil spill was found to be 0.055 mm/s. A major concern for public safety is the content and extent of the smoke plume from the fires. Smoke yield, the fraction of the oil mass burned that is emitted as particulate, was found to be 13 percent. A large-eddy simulation calculation method for smoke plume trajectory and smoke particulate deposition developed by NIST showed that the smoke particulate deposition from a 114 m2 burn would occur in striations over a long, slender area 3.2 km wide and 258 km downwind of the burn.
Effect of carbon-based nanoparticles on the ignition, combustion and flame characteristics of crude oil droplets

Gurjap Singh,Mehdi Esmaeilpour,Albert Ratner

DOI: https://doi.org/10.1016/j.energy.2020.117227

IF: 9

2020-04-01

Energy

Abstract:<p>The use of in-situ burning (ISB) as a clean-up response in the event of an oil spill has generated controversy because of unburned hydrocarbons and products of incomplete combustion left behind on an ISB site. These substances threaten marine life, both in the ocean and on the ocean floor. Treating crude oil as a multicomponent liquid fuel, this manuscript investigates the effect of carbon-based nanomaterials, acetylene black (AB) and multi-walled carbon nanotube (MWNT), on the combustion and flame characteristics of crude sourced from the Bakken formation (ND, USA). Sub-millimeter droplets of colloidal suspensions of Bakken crude and nanomaterials at various particle loadings were burned, and the process was captured with CMOS and CCD cameras. The resulting images were post-processed to generate burning rate, ignition delay, total combustion time, and flame stand-off (FSR) ratio data for the various crude suspensions. A maximum combustion rate enhancement of 39.5% and 31.1% was observed at a particle loading of 0.5% w/w acetylene black nanoparticles and 0.5% w/w multi-walled carbon nanotubes, respectively. Generally, FSR for pure Bakken was noted as larger than for Bakken with nanoparticle additives. These results are expected to spur further investigations into the use of nanomaterials for ISB crude oil clean-ups.</p>

energy & fuels,thermodynamics
Mechanisms and streams for processing of "what" and "where" in auditory cortex.

J. Rauschecker,B. Tian

DOI: https://doi.org/10.1073/PNAS.97.22.11800

2000-10-24

Abstract:The functional specialization and hierarchical organization of multiple areas in rhesus monkey auditory cortex were examined with various types of complex sounds. Neurons in the lateral belt areas of the superior temporal gyrus were tuned to the best center frequency and bandwidth of band-passed noise bursts. They were also selective for the rate and direction of linear frequency modulated sweeps. Many neurons showed a preference for a limited number of species-specific vocalizations ("monkey calls"). These response selectivities can be explained by nonlinear spectral and temporal integration mechanisms. In a separate series of experiments, monkey calls were presented at different spatial locations, and the tuning of lateral belt neurons to monkey calls and spatial location was determined. Of the three belt areas the anterolateral area shows the highest degree of specificity for monkey calls, whereas neurons in the caudolateral area display the greatest spatial selectivity. We conclude that the cortical auditory system of primates is divided into at least two processing streams, a spatial stream that originates in the caudal part of the superior temporal gyrus and projects to the parietal cortex, and a pattern or object stream originating in the more anterior portions of the lateral belt. A similar division of labor can be seen in human auditory cortex by using functional neuroimaging.
In situ burning via towed boom of oil spilled at sea

George Carrier,Francis Fendell,Jay Mitchell,G CARRIER,F FENDELL,J MITCHELL

DOI: https://doi.org/10.1016/0010-2180(92)90091-3

IF: 4.4

1992-09-01

Combustion and Flame

Abstract:Operational guidance for the efficient use of combustion in the cleanup of a surface oil film, formed as a result of a spill at sea, is sought by approximate analysis. In remediation by burning, the spilled oil itself provides the energy for its cleanup. Attention is focused on situations holding relative ly far from the source of the spill and/or relatively long after the spill: the oil is taken to have so dispersed that the thickness of the film is on the order of a few millimeters. Under such conditions, the oil film is unlikely to burn without the use of multiple towed booms, each boom spreading its already-ignited, localized fire to continuously collected, previously unignited portions of the oil film. A simple, quasisteady, two-dimensional analysis suggests efficient values for the tow speed and the tow-line length as functions of such parameters as the oil density, oil-film thickness, oil burn/evaporation rate, etc. The analysis leads to specific suggestions for apparently unreported laboratory experiments that may be informative prior to at-sea operation.

energy & fuels,engineering, chemical, mechanical,thermodynamics, multidisciplinary
Proof of concept study for in-situ burn application using conventional containment booms - Design of Burning Tongue

Lin Zhao,Cosan Daskiran,Douglas A Mitchell,Paul D Panetta,Michel C Boufadel,Tim J Nedwed

DOI: https://doi.org/10.1016/j.jhazmat.2022.129403

2022-10-05

Abstract:In situ burning (ISB) hasn't been widely used for offshore oil spill response for various reasons. We present a feasibility study for a new ISB method - the Burning Tongue (BT) concept. We conducted scaled experiments in the Ohmsett wave tank to demonstrate its feasibility. We produced a 35-m long "tongue" of burnable oil (average oil thickness 4.2 mm - above the thickness needed for ISB) by towing a conventional boom (with a 12″ (0.3 m) deep skirt) partially filled with crude oil and then released the oil through a 6″ (0.15 m) wide opening at the apex. We found that the boom movement produced a convergence zone just downstream that kept released oil thick and also pulled oil that entrained under the boom skirt into the thick "tongue" of oil. CFD modeling was performed to explain the flow hydrodynamics and the formation of the convergence zone, which indicates the phenomenon is universal. We used small harbor boom only partially filled with oil for this study and believe that a full-scale marine boom filled with oil would achieve an even thicker "burning tongue." The BT concept could make ISB more widely used for oil spill response in offshore areas.
Experimental study for flame base drag and burning efficiency of spilled crude oil during in-situ burning on water

Depeng Kong,Xu He,Hanbing Yang,Zhen Zhang

DOI: https://doi.org/10.1016/j.psep.2019.08.006

IF: 7.8

2019-11-01

Process Safety and Environmental Protection

Abstract:In-situ burning (ISB) has been proven to be a practical way to clean oil on water. The burning behavior of spilled oil is strongly influenced by wind. The flame characteristics of flame base drag and burning efficiency affected by wind speed have been studied through a series of experiments in this study. The wind speeds varied from 0.5 m/s to 2.0 m/s and the inside diameters of the oil pools made from quartz glass were 40 mm, 90mm and 140mm. The variation of fuel vapor density was considered in the dimensionless model for predicting flame base drag length. The proposed formula was shown to correlate with the data of different pool diameters and wind speeds non-dimensionally by Froude number, fuel-air density ratio and the dimensionless heat release rate. The study helped to better understand the fire behavior under wind conditions, and most importantly the developed model would help guide better assessment of the burning in ISB operation.

engineering, environmental, chemical
Caged gene-inducer spatially and temporally controls gene expression and plant development in transgenic Arabidopsis plant.

Ken-ichiro Hayashi,K. Hashimoto,Naoyuki Kusaka,A. Yamazoe,H. Fukaki,M. Tasaka,H. Nozaki

DOI: https://doi.org/10.1016/J.BMCL.2006.01.103

IF: 2.94

2006-05-01

Bioorganic & Medicinal Chemistry Letters

Abstract:
Comparative clinical study of coumadin sodium and dicumarol in patients with thromboembolic diseases.

C. Shapiro,R. Lisker,A. Lichtman,A. M. Josephson

DOI: https://doi.org/10.1016/0002-8703(58)90256-4

IF: 5.099

American Heart Journal

Abstract:
Modification of cardiac sodium current by intracellular application of cAMP

H. Muramatsu,T. Kiyosue,M. Arita,T. Ishikawa,H. Hidaka

DOI: https://doi.org/10.1007/BF00374682

Pflügers Archiv

Abstract:
Chemical signatures of polycyclic aromatic hydrocarbons in the emissions from in situ oil burns

Fang Yin,Chen Gao,Zhibo Song,Yuling Han,Zhiwei He,Li Zhang,Penghao Su,Daolun Feng,Tao Yang,Jie Fu

DOI: https://doi.org/10.1016/j.marpolbul.2022.114194

Abstract:This study characterized the parent and alkylated polycyclic aromatic hydrocarbons (PAHs) in gaseous and particulate emissions from the in situ burning (ISB) of oils. The experimental results indicate that the burning of the heavy oil produced the most PAH emissions because of its longest burning time. In addition, the parent PAHs mainly exist in the particulate phase, while alkylated PAHs mostly accumulate in the gaseous phase. In particular, the diagnostic-ratios of PAHs with great stability in both gaseous and particulate emissions from ISB are identified by comparing the laboratory and field data. The presences of bell-, slope- and V-shaped distribution patterns of alkylated PAHs in the emissions precisely indicate their sources to be petrogenic and pyrogenic processes occurring during ISB. The formation of 2-methylanthracene during ISB is confirmed. The overall findings are expected to provide a prospective protocol to characterize PAH pollution from ISB emissions in case of oil spills.
In-Situ Burning for Oil Spills in Arctic Waters: State-of-the-Art and Future Research Needs

Stephen Potter,Ian Buist

DOI: https://doi.org/10.1007/978-1-4020-8565-9_5

2008-01-01

Abstract:In-situ burning is one of the few practical options for removing oil spilled in ice-covered waters. In many instances in-situ burning, combined with surveillance and monitoring, may be the only response possible. As with all countermeasures in any environment, the suitability of burning a particular spill depends on the characteristics of the spilled oil and how the oil behaves in the particular ice conditions. There is an extensive body of knowledge concerningin-situ burning of oil in ice situations, beginning with laboratory, tank and field studies in the mid-1970s in support of drilling in the Canadian Beaufort Sea.In-situ burning research has been conducted primarily in Canada, Norway and the United States. This paper serves as a review of the subject, incorporating recent research results, summarizing the following topics:The basic requirements and processes involved with in-situ burningTrade-offs associated with burning in ice-covered watersHow oil spill behavior in various ice conditions controls in-situ burningThe application of burning in various common ice situations andKey equipment requirements.
TEXAS MARSH BURN: REMOVING OIL FROM A SALT MARSH USING IN SITU BURNING

Manuel F. Gonzalez,Gabriel A. Lugo

DOI: https://doi.org/10.7901/2169-3358-1995-1-39

1995-02-01

International Oil Spill Conference Proceedings

Abstract:ABSTRACT Frequently coastal marsh is burned to enhance regrowth; but rarely is it burned to remove spilled oil. On January 7, 1992, a 40.64 cm crude oil pipeline ruptured causing a spill in a salt marsh. Four days later, in an unprecedented cleanup coordinated by Exxon Pipeline Company and the Texas General Land Office, 1,150 barrels of South Texas crude was ignited and removed, minimizing environmental damage to Copano Bay, Chiltipin Creek, and the surrounding wetlands. This cleanup had been made difficult by inclement weather and heavy rainfall that saturated the marsh. Ingress and egress had damaged the marsh and was discontinued. Conventional mechanical cleanup techniques had been used with minimal success. Alternative methods like bioremediation, low pressure flooding, and peat moss applications were considered, but proved unfeasible. The unified command system then made an application for a permit to burn and gained approval. Seventy-six hours into the event, a successful test burn was conducted; one day later, the majority of the oil was ignited. It maintained a full burn for 21 hours, self-extinguished, and later was re-ignited for further removal. Emerging technologies such as in-situ burning are additional implements in the oil spill responder's toolbox. In Texas, burning helped save a marsh.
Effect of spilled diluted bitumen on chemical air-water exchange in boreal lake limnocorrals

Leslie J Saunders,Jose L Rodriguez-Gil,Sawyer S Stoyanovich,Linda E Kimpe,Mark L Hanson,Bruce P Hollebone,Diane M Orihel,Jules M Blais

DOI: https://doi.org/10.1016/j.chemosphere.2021.132708

IF: 8.8

Chemosphere

Abstract:Following spills into water, petroleum oils can spread widely and produce surface slicks. Resulting slicks may impede volatilization and possibly increase chemical persistence in water. While the influence of oil films on chemical air-water exchange has been examined through theoretical and laboratory studies, field studies have not been conducted to assess the relevance of these effects following actual oil spill events. Here we evaluated the effect of diluted bitumen (dilbit) experimentally spilled in limnocorrals installed in a boreal lake on the volatilization of sulfur hexafluoride (SF6), a non-reactive volatile tracer gas. Dilbit spills were monitored over 70 days and SF6 was introduced twice (after 7 and 48 days) to evaluate the influence of spilled dilbit on the loss of SF6 from water. Volatilization rate constants of SF6 (kVOL) significantly decreased by up to 80% with increasing total dilbit spill cover. Using a theoretical equation, decreases in kVOL were largely explained by a reduction in open water area where chemical exchange across the air-water interface occurs. Apparent effects of the slick on SF6 mass transfer were estimated to be smaller by comparison (20%).To account for this reduction in volatilization, oil spill fate models should include a correction to consider the impact of spill cover on the air-water exchange of organic chemicals.
ADVANTAGES AND DISADVANTAGES OF BURNING SPILLED OIL

Alan A. Allen,Ronald J. Ferek

DOI: https://doi.org/10.7901/2169-3358-1993-1-765

1993-03-01

International Oil Spill Conference Proceedings

Abstract:ABSTRACT The full potential for in situ burning as a controlled oil spill response technique is a subject of growing interest throughout the world. Information now available from burning oil during accidental fires, war-related fires in Kuwait, spillage from the Exxon Valdez, and controlled test burns, permits an objective and comprehensive assessment of both the positive and negative aspects of in situ burning. A thorough analysis has been made of direct and indirect impacts and concerns typically associated with the decision, to burn or not to burn. These factors, together with the comparative costs of various response techniques, have been identified and described to provide spill control planners and response organizations with a means of assessing the potential use of burning to clean up offshore oil spills.
Role of Wettability Alteration in Enhanced Oil Recovery by In Situ Combustion: A Comprehensive Experimental and Modeling Study

Xing Jin,Wanfen Pu,Yongqiang Chen,Yuanyuan Bai,Shuai Zhao

DOI: https://doi.org/10.1021/acs.energyfuels.3c04181

IF: 4.6541

2024-01-17

Energy & Fuels

Abstract:In situ combustion (ISC) is a primary technique used to enhance oil recovery in heavy oil reservoirs. By performing controlled burning of the oil in place, the heavy oil is expected to be lighter and easier to flow. Conventional studies mainly considered the viscosity reduction during this process. This ISC process may change the fluid-rock wettability. However, the role of wettability alteration is not well investigated during ISC. To fill this knowledge gap, we performed ISC and measured the dynamic surface wettability changes under different combustion temperatures. Furthermore, relative permeability curves were interpolated to quantify the effects of wettability changes in heavy oil recovery during ISC. This study revealed wettability change during ISC. As the temperature increases, the contact angle decreases. At firing temperatures of 200, 300, 400, and 500 °C, the rock wettability changed to hydrophilicity, with a stronger hydrophilicity observed at higher temperatures. However, at 200 °C, the hydrophilicity was not strong. This was due to the low-temperature oxidation of the crude oil at the combustion temperature of 200 °C, and the oxidized oil was attached to the rock surface, causing the rock wettability to become hydrophobic. Numerical simulation results demonstrated that the transition from oil-wet to strong hydrophilic wettability is favorable for oil recovery, resulting in an increased recovery factor of 8.75%. This confirms that wettability alteration in the reservoir is one of the main mechanisms for heavy oil recovery during ISC. These findings indicate the influence of reservoir wettability on oil recovery during the ISC process and contribute to further understanding of the ISC mechanism.

energy & fuels,engineering, chemical
Self-sustaining smouldering combustion for the treatment of industrial oily waste

Andrew W Sims,Gabriel P Sabadell,Carl W Lam,Daniel C Segal,Paul Bireta,Dave Thomas

DOI: https://doi.org/10.1177/0734242X221123145

2022-09-22

Abstract:Waste Management &Research, Ahead of Print. Significant onsite handling and offsite management costs are incurred by oilfield operators annually to properly manage hydrocarbon waste streams such as tank bottoms or other oily sludge or oil impacted soil generated during oil and gas production processes. The current study reports for the first-time technical results of a field trial on use of a smouldering combustion technology performed in an active oilfield. Two treatment batches with oily sludges, stabilized through blending with soil, resulted in permanent hydrocarbon removal (98–99.9% reduction) to create treated soil that met standards for reuse as clean backfill onsite. Emissions profile data collected pre- and post-thermal oxidizer indicated effective removal of volatile organic compounds, CO and SO2, but had increased NO and CO2 due to combustion of propane to affect the thermal oxidation. Regulatory, financial, environmental and safety considerations are discussed in context of future full-scale smouldering technology deployment. The technology has the potential to lower overall unit costs for management of hydrocarbon impacted waste and reduce waste sent to landfills, which can benefit more remote sites.

environmental sciences,engineering, environmental
In-situ burning of spilled hydrocarbons using multiple pool fire numerical models

Man Chun Sin,Til Baalisampang,Pingcheng Zhu,Ehsan Arzaghi,Vikram Garaniya,Rouzbeh Abbassi

DOI: https://doi.org/10.1007/s42797-022-00052-6

2022-03-03

Safety in Extreme Environments

Abstract:In-situ burning is one of the methods used for oil spill cleanup. Optimising an in-situ burning method using multiple pool fires (MPF) has not been widely studied. In this study, a novel framework is proposed to assess the effectiveness of an MPF in response to oil spills on water surfaces. The framework is applied to four cases using the Fire Dynamics Simulator (FDS). It is found that an MFP can result in incomplete combustion and negative pressure effects if pools are too close to each other, thereby resulting in a reduction in the mass burning rate. However, an MFP has a higher mass burning rate of spilled oil than a single pool fire if appropriate distances among pool fires are maintained. An MFP can increase the speed of recovering the oil compared with a single pool fire due to high temperature and heat flux.

Opioids at Cape Cod

Composition of the dissolved organic matter produced during in situ burning of spilled oil

Impact of wind on in-situ burning behavior of spilled oil on open water

Occupational exposure to air pollutants emitted from in situ burning of offshore oil spills: a large-scale field study

MESOSCALE EXPERIMENTS HELP TO EVALUATE IN-SITU BURNING OF OIL SPILLS1

Effect of carbon-based nanoparticles on the ignition, combustion and flame characteristics of crude oil droplets

Mechanisms and streams for processing of "what" and "where" in auditory cortex.

In situ burning via towed boom of oil spilled at sea

Proof of concept study for in-situ burn application using conventional containment booms - Design of Burning Tongue

Experimental study for flame base drag and burning efficiency of spilled crude oil during in-situ burning on water

Caged gene-inducer spatially and temporally controls gene expression and plant development in transgenic Arabidopsis plant.

Comparative clinical study of coumadin sodium and dicumarol in patients with thromboembolic diseases.

Modification of cardiac sodium current by intracellular application of cAMP

Chemical signatures of polycyclic aromatic hydrocarbons in the emissions from in situ oil burns

In-Situ Burning for Oil Spills in Arctic Waters: State-of-the-Art and Future Research Needs

TEXAS MARSH BURN: REMOVING OIL FROM A SALT MARSH USING IN SITU BURNING

Effect of spilled diluted bitumen on chemical air-water exchange in boreal lake limnocorrals

ADVANTAGES AND DISADVANTAGES OF BURNING SPILLED OIL

Role of Wettability Alteration in Enhanced Oil Recovery by In Situ Combustion: A Comprehensive Experimental and Modeling Study

Self-sustaining smouldering combustion for the treatment of industrial oily waste

In-situ burning of spilled hydrocarbons using multiple pool fire numerical models