Random dynamical systems generated by stochastic Navier–Stokes equations on a rotating sphere

Z. Brzeźniak,B. Goldys,Q. Gia

DOI: https://doi.org/10.1016/J.JMAA.2015.01.054

2014-03-26

Abstract:

What problem does this paper attempt to address?

Z-schematic Water Splitting by the Synergistic Effect of a Type-Ii Heterostructure and a Highly Efficient Oxygen Evolution Catalyst

Xiaoyun Li,Haihua Hu,Lingbo Xu,Can Cui,Degui Qian,Shuang Li,Wenzhe Zhu,Peng Wang,Ping Lin,Jiaqi Pan,Chaorong Li

DOI: https://doi.org/10.1016/j.apsusc.2018.01.216

IF: 6.7

2018-01-01

Applied Surface Science

Abstract:Artificial Z-scheme system inspired by the natural photosynthesis in green plants has attracted extensive attention owing to its advantages such as simultaneously wide range light absorption, highly efficient charge separation and strong redox ability. In this paper, we report the synthesis of a novel all-solidstate direct Z-scheme photocatalyst of Ag3PO4/CeO2/TiO2 by depositing Ag3PO4 nanoparticles (NPs) on CeO2/TiO2 hierarchical branched nanowires (BNWs), where the CeO2/TiO2 BNWs act as a novel substrate for the well dispersed nano-size Ag3PO4. The Ag3PO4/CeO2/TiO2 photocatalyst exhibits excellent ability of photocatalytic oxygen evolution from pure water splitting. It is suggested that the Z-scheme charge transfer route between CeO2/TiO2 and Ag3PO4 improves the redox ability. On the other hand, the cascade energy level alignment in CeO2/TiO2 BNWs expedites the spatial charge separation, and hence suppresses photocatalytic backward reaction. However, it is difficult to realize a perfect excitation balance in Ag3PO4/CeO2/TiO2 and the composite still surfers photo-corrosion in photocatalysis reaction. Nevertheless, our results provide an innovative strategy of constructing a Z-scheme system from a type-II heterostructure and a highly efficient oxygen evolution catalyst. (C) 2018 Elsevier B.V. All rights reserved.
Integration of surficial oxygen vacancies and interfacial two-dimensional NiFe-layered double hydroxide nanosheets onto bismuth vanadate photoanode for boosted photoelectrochemical water splitting

Pratik Mane,Vishal Burungale,Hyojung Bae,Chaewon Seong,Jiwon Heo,Soon Hyung Kang,Jun-Seok Ha

DOI: https://doi.org/10.1016/j.jpowsour.2023.233832

IF: 9.2

2023-11-17

Journal of Power Sources

Abstract:Considering its outstanding cost-to-efficiency ratio, N-type bismuth vanadate (BiVO 4 ) is an ideal photoanode for photoelectrochemical (PEC) water splitting. Nevertheless, the widespread application of BiVO 4 is being hindered commercially by innate challenges such as its poor carrier mobility, short hole diffusion length , and sluggish oxidation chemistry . Herein, we report the unique integration of surficial oxygen vacancies (O vac ) in conjunction with two-dimensional (2D) nickel-iron (NiFe) layered double hydroxide (LDH) nanosheets onto pristine BiVO 4 photoanode to tweak the charge transfer kinetics during water splitting. The introduction of oxygen vacancies efficiently modulates band energetics, amplifies light absorption, and augments the carrier density. Concurrently, the 2D NiFe-LDH nanosheets play a dual role by facilitating interfacial hole transfer, thereby reducing excessive defect states, and serving as a protective layer against photocorrosion, ultimately resulting in a notable improvement in solar-driven water oxidation efficiency. The results of PEC water-splitting experiments demonstrate that the BiVO 4 photoanode enriched with surficial oxygen vacancies and NiFe-LDH (BiVO 4 :O vac /NiFe-LDH) achieved a photocurrent density of 2.92 mA cm −2 with ∼3-fold enhancement compared with a pristine BiVO 4 photoanode. The engineered BiVO 4 system yielded an impressive photoconversion efficiency of 1.29 %, charge separation efficiency (η sep ) > 40 %, and charge transport efficiency (η trans ) > 35 %, clearly evidencing a boost in the charge dynamics of pristine BiVO 4 . Furthermore, during long-term stability testing, BiVO 4 :O vac /NiFe-LDH retained 91 % of its initial photocurrent density for ∼20 h without any significant deterioration. This work sheds light on the role of integrating surface and interface engineering tactics for enhancing photo-induced charge transport in BiVO 4 , thereby providing efficient and stable PEC water splitting.

energy & fuels,materials science, multidisciplinary,electrochemistry,chemistry, physical
Systematic engineering of BiVO4 photoanode for efficient photoelectrochemical water oxidation

Zhiting Liang,Meng Li,Kai‐Hang Ye,Tongxin Tang,Zhan Lin,Yuying Zheng,Yongchao Huang,Hongbing Ji,Shanqing Zhang

DOI: https://doi.org/10.1002/cey2.413

2023-09-17

Carbon Energy

Abstract:A Fe‐g‐C3N4/BiVO4 heterojunction photoanode has been synthesized by both heterojunction engineering and doping, which extends the absorption range to longer wavelengths. Owing to the excellent oxygen evolution reaction activity of the NiCoOx layer and enhanced light absorption due to the two‐electrodes stack design, the photocurrent density of the as‐prepared photoanode achieves 6.33 mA cm−2 at 1.23 V versus RHE. BiVO4 is one of the most promising photoanode materials for photoelectrochemical (PEC) solar energy conversion, but it still suffers from poor photocurrent density due to insufficient light‐harvesting efficiency (LHE), weak photogenerated charge separation efficiency (ΦSep), and low water oxidation efficiency (ΦOX). Herein, we tackle these challenges of the BiVO4 photoanodes using systematic engineering, including catalysis engineering, bandgap engineering, and morphology engineering. In particular, we deposit a NiCoOx layer onto the BiVO4 photoanode as the oxygen evolution catalyst to enhance the ΦOX of Fe‐g‐C3N4/BiVO4 for PEC water oxidation, and incorporate Fe‐doped graphite‐phase C3N4 (Fe‐g‐C3N4) into the BiVO4 photoanode to optimize the bandgap and surface areas to subsequently expand the light absorption range of the photoanode from 530 to 690 nm, increase the LHE and ΦSep, and further improve the oxygen evolution reaction activity of the NiCoOx catalytic layer. Consequently, the maximum photocurrent density of the as‐prepared NiCoOx/Fe‐g‐C3N4/BiVO4 is remarkably boosted from 4.6 to 7.4 mA cm−2. This work suggests that the proposed systematic engineering strategy is exceptionally promising for improving LHE, ΦSep, and ΦOX of BiVO4‐based photoanodes, which will substantially benefit the design, preparation, and large‐scale application of next‐generation high‐performance photoanodes.
Efficient Solar Water Splitting via Enhanced Charge Separation of the BiVO 4 Photoanode

Lina Wang,Zejun Liu,Xiaohong Xu,Yuefa Jia,Qiong Mei,Fei Ding,Jianhong Peng,Qizhao Wang

DOI: https://doi.org/10.1021/acsaem.2c00779

IF: 6.4

2022-05-13

ACS Applied Energy Materials

Abstract:Bismuth vanadate (BiVO4) with a narrow band gap was considered as one of the most desirable matrices for the photoelectrode in a photoelectrochemical (PEC) water splitting system. However, the serious recombination rate of photogenerated charges in BiVO4 causes the practical PEC efficiency to be significantly lower than the theoretical value. Herein, we provide a simple route for modification of BiVO4-based photoanodes with Ni-NDAD to promote charge separation and accelerate water oxidation kinetics. As a result, the Ni-NDAD/BiVO4 photoelectrodes deliver a high photocurrent density of 5.6 mA cm–2 (1.23 V vs reversible hydrogen electrode) and an incident photon-to-current conversion efficiency of 80% (460 nm), which were around 3.5- and 5.3-fold higher than that of pristine BiVO4, respectively. In addition, the introduction of Ni-NDAD on BiVO4 could trap photogenerated holes transferred from BiVO4, thus allowing significant acceleration of water oxidation kinetics and overall improvement in the performance of the whole BiVO4-based PEC water splitting system. Furthermore, the Ni-NDAD/BiVO4 photoanode also displayed high PEC catalytic activity for chlortetracycline (CTC) removal in the presence of persulfate (PS), achieving an 89.19% degradation efficiency within 30 min. This work provides a promising design strategy for efficient photogenerated charge separation to improve PEC water splitting and organic contaminant removal.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Decoration of BiVO4 Photoanodes with Near-Infrared Quantum Dots for Boosted Photoelectrochemical Water Oxidation

Mengke Cai,Xin Li,Hongyang Zhao,Cheng Liu,Yimin You,Feng Lin,Xin Tong,Zhiming M. Wang

DOI: https://doi.org/10.1021/acsami.1c15973

IF: 9.5

2021-01-01

ACS Applied Materials & Interfaces

Abstract:Broadening light absorption and improving charge carrier separation are very critical to boost the water splitting efficiency in photoelectrochemical (PEC) systems. We herein reported a heterostructured photoanode consisting of BiVO4 and eco-friendly, near-infrared (NIR) CuInSeS@ZnS core-shell quantum dots (QDs) for PEC water oxidation. The decoration of core-shell QDs concurrently extends the absorption range of BiVO4 from the ultraviolet-visible to NIR region and promotes the effective separation and transfer of photo-excited electrons and holes. Without any sacrificial agents and co-catalysts, the as-fabricated NIR core-shell QDs/BiVO4 heterostructured photoanodes exhibit an approximately fourfold higher photocurrent density than that of the bare BiVO4, up to 3.17 mA cm-2 at 1.23 V versus the reversible hydrogen electrode. It is revealed that both a suitable band alignment and an intimate interfacial junction between QDs and BiVO4 are the main factors that result in enhanced charge separation and transfer efficiencies. We also highlight that the NIR CISeS QDs passivated with a ZnS shell can suppress the non-radiative recombination and enhance the stability of the QD photoanodes for optimized PEC performance. This work provides a facile and effective approach to boost the water oxidation efficiency of semiconductor photoanodes via utilizing NIR core-shell QDs as a light sensitizer and charge carrier separator.
Decoration of BiVO 4 Photoanodes with Near-Infrared Quantum Dots for Boosted Photoelectrochemical Water Oxidation

Mengke Cai,Xin Li,Hongyang Zhao,Cheng Liu,Yimin You,Feng Lin,Xin Tong,Zhiming M. Wang

DOI: https://doi.org/10.1021/acsami.1c15973

2021-10-12

Abstract:Broadening light absorption and improving charge carrier separation are very critical to boost the water splitting efficiency in photoelectrochemical (PEC) systems. We herein reported a heterostructured photoanode consisting of BiVO4 and eco-friendly, near-infrared (NIR) core–shell quantum dots (QDs) for PEC water oxidation. The decoration of core–shell QDs concurrently extends the absorption range of BiVO4 from the ultraviolet–visible to NIR region and promotes the effective separation and transfer of photo-excited electrons and holes. Without any sacrificial agents and co-catalysts, the as-fabricated NIR core–shell QDs/BiVO4 heterostructured photoanodes exhibit an approximately fourfold higher photocurrent density than that of the bare BiVO4, up to 3.17 mA cm–2 at 1.23 V versus the reversible hydrogen electrode. It is revealed that both a suitable band alignment and an intimate interfacial junction between QDs and BiVO4 are the main factors that result in enhanced charge separation and transfer efficiencies. We also highlight that the NIR CISeS QDs passivated with a ZnS shell can suppress the non-radiative recombination and enhance the stability of the QD photoanodes for optimized PEC performance. This work provides a facile and effective approach to boost the water oxidation efficiency of semiconductor photoanodes via utilizing NIR core–shell QDs as a light sensitizer and charge carrier separator.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c15973.Detailed sample full names and abbreviations, size distribution, XRD, HRTEM, EDX elemental mapping images, GC data, PEC performance comparison, Nyquist plots, open-circuit voltage, UV–vis, Tauc plots, PL, UPS and HRXPS spectra, Mott–Schottky plots, and TA and the fitting parameters of PL lifetime for QDs and QDs-based photoanodes (PDF)This article has not yet been cited by other publications.

materials science, multidisciplinary,nanoscience & nanotechnology
Interface-engineered dual Z-scheme of BiVO4/NH2-MIL-125(Ti)/POF photoanode with enhanced photoelectrochemical performance

Hao Du,Wanggang Ma,Jianying Qian,Xin Ma,Meng Tan,Chunyan Sun,Qi Wang

DOI: https://doi.org/10.1016/j.jece.2024.112269

IF: 7.7

2024-04-01

Journal of Environmental Chemical Engineering

Abstract:The key factors that restrain the decomposition activity of photoelectrocatalysis (PEC) are poor redox ability and low charge separation rate. In this work, the dual Z-scheme BiVO4/NH2-MIL-125(Ti)/POF (BiVO4/NM125(Ti)/POF) heterojunctions were successfully established for visible-light driven PEC degradation of phenol. As expected, the optimum BiVO4/NM125(Ti)/POF photoanode exhibited outstanding PEC performance with near-total degradation of phenol within 2 h of illumination. The evaluated activity was assigned to high charge transfer rate and dual Z-scheme heterostructures with double electron transport channels. The fabrication of dual Z-scheme heterojunctions improved a more efficient separation of photo-induced charge carriers while holding a higher redox ability to generate more reactive oxygen species (ROS) such as O2 •− and •OH to decompose organic pollutants. In addition, excellent chemical stability and recyclability were also achieved after five times cycles, and the degradation pathway of phenol was also put forward. Finally, the quantitative structure-activity relationship (QSAR) was applied to forecast phenol and its degradation products toxicity. This research gives novel insights into establishing highly effective photoanode with promising applications for organic contaminants degradation, and offers in-depth understanding of charge separation and migration in PEC process.

engineering, chemical, environmental
Synergistic Surface Engineering of BiVO4 Photoanodes for Improved Photoelectrochemical Water Oxidation

Shan Wang,Zhijian Shi,Kunrong Du,Zhizhen Ren,Haifeng Feng,Jiaou Wang,Liang Wang,Dandan Cui,Yi Du,Weichang Hao

DOI: https://doi.org/10.1002/smtd.202401443

IF: 12.4

2024-11-02

Small Methods

Abstract:The BiVO4/NiOx‐B photoanode is prepared by two different surface modifying methods. Fast charge separation and efficient surface catalytic reactions can be realized in BiVO4 photoanodes by a positive synergistic effect of NiOx catalysts and surface borate moieties (BO3 groups). The BiVO4/NiOx‐B photoanode exhibits an improved photocurrent density of 5.76 mA cm−2 at 1.23 V vs. RHE with excellent PEC stability. Surface engineering of BiVO4 photoanodes is effective and feasible for photoelectrochemical (PEC) water splitting. To achieve superior PEC performance, however, more than one surface engineering method is usually indispensable, for which a positive synergistic effect is vital and thus highly desired. Herein, it is reported that the incorporation of borate moieties into ultrathin p‐type NiOx catalysts can induce the reconfiguration of surface catalytic sites to form new highly active species, in addition to enhanced fast charge separation and transfer. The photocurrent density of BiVO4 photoanodes is enhanced from 1.49 to 5.76 mA cm−2 at 1.23 V versus reversible hydrogen electrode (RHE) under AM 1.5G illumination, which is achieved by successive modifications of NiOx and borate moieties. It is found that BO3 groups anchored to Ni atoms by replacing the surface hydroxyl sites of NiOx catalysts not only increase the relative ratio of Ni3+ species to facilitate charge transfer but also provide efficient active sites for H2O molecule adsorption and oxidation reactions. This work demonstrates the positive synergistic effect of these two surface engineering methods and provides an effective pathway to construct highly efficient and stable photoanodes for PEC water splitting.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology
Interface Modulation of BiVO4 Based Photoanode with Bi(III)Bi(V)O4 for Enhanced Solar Water Splitting

Ming Ma,Zheng Xing,Xi Zhu,Peng Jiang,Xiao Wang,He Lin,Yiming An,Haibin Su,Shihe Yang

DOI: https://doi.org/10.1016/j.jcat.2020.09.012

IF: 7.3

2020-01-01

Journal of Catalysis

Abstract:Despite being considered as one of the most promising semiconductor photocatalysts, BiVO4 still suffers the problems of inefficient light harvesting, multiple charge recombination channels and back reactions, restricting its application for solar energy conversion. Here, we demonstrate a unique Bi2O4(400)/BiVO4(040) heterojunction prepared via an oxidation conversion process, which dramatically accelerated the interfacial charge transfer compared to pure BiVO4. Furthermore, with Mo doping, carbon quantum dots (CQDs) loading and Ni-FeOOH co-catalyst deposition, the resulting Bi2O4/Mo-BiVO4/CQDs/Ni-FeOOH photoanode reaches a remarkable photocurrent density of 6.7 mA/cm(2) at 1.23 V vs. RHE under AM 1.5G irradiation in the absence of hole scavengers. Our findings demonstrate that proper material interface engineering together with composition tuning provides a viable route to achieve highly efficient solar water splitting. (C) 2020 Elsevier Inc. All rights reserved.
Nanostructured BiVO4 Photoanodes Fabricated by Vanadium-infused Interaction for Efficient Solar Water Splitting

Amar K. Salih,Abdul Zeeshan Khan,Qasem A. Drmosh,Tarek A. Kandiel,Mohammad Qamar,Tahir Naveed Jahangir,Cuong Ton-That,Zain H. Yamani

2024-05-05

Abstract:Bismuth vanadate (BiVO4) has emerged as a highly prospective material for photoanodes in photoelectrochemical (PEC) water oxidation. However, current limitations with this material lie in the difficulties in producing stable and continuous BiVO4 layers with efficient carrier transfer kinetics, thereby impeding its widespread application in water splitting processes. This study introduces a new fabrication approach that yields continuous, monoclinic nanostructured BiVO4 films, paving the way for their use as photoanodes in efficient PEC water oxidation for hydrogen production under solar light conditions. The fabrication involves the intercalation of vanadium (V) ions into Bi2O3 films at 450oC. Upon interaction with V ions, the film undergoes a transformation from tetragonal Bi2O3 to monoclinic scheelite BiVO4. This synthesis method enables the fabrication of single monoclinic phase BiVO4 films with thicknesses up to 270 nm. The engineered monoclinic BiVO4 film, devoid of any pinholes that could cause carrier loss, exhibits a robust photocurrent of 1.0 mA/cm2 at 1.23 VRHE in a neutral electrolyte, without requiring additional modifications or doping. Moreover, we demonstrate that the incorporation of a cobalt phosphate (Co-Pi) co-catalyst into the BiVO4 photoanode significantly enhances the lifetime of photogenerated holes by a factor of nine, resulting in a further elevation of the photocurrent to 2.9 mA/cm2. This remarkable PEC enhancement can be attributed to the surface state passivation by the Co-Pi co-catalyst. Our fabrication approach opens up a new facile route for producing large-scale, highly efficient BiVO4 photoanodes for PEC water splitting technology.

Materials Science
Promoting the Photoelectrochemical Properties of BiVO4 Photoanode via Dual Modification with CdS Nanoparticles and NiFe-LDH Nanosheets

Guofa Dong,Tingting Chen,Fangxia Kou,Fengyan Xie,Caihong Xiao,Jiaqi Liang,Chenfang Lou,Jiandong Zhuang,Shaowu Du

DOI: https://doi.org/10.3390/nano14131100

2024-06-26

Abstract:Bismuth vanadate (BiVO4) has long been considered a promising photoanode material for photoelectrochemical (PEC) water splitting. Despite its potential, significant challenges such as slow surface water evolution reaction (OER) kinetics, poor carrier mobility, and rapid charge recombination limit its application. To address these issues, a triadic photoanode has been fabricated by sequentially depositing CdS nanoparticles and NiFe-layered double hydroxide (NiFe-LDH) nanosheets onto BiVO4, creating a NiFe-LDH/CdS/BiVO4 composite. This newly engineered photoanode demonstrates a photocurrent density of 3.1 mA cm-2 at 1.23 V vs. RHE in 0.1 M KOH under AM 1.5 G illumination, outperforming the singular BiVO4 photoanode by a factor of 5.8 and the binary CdS/BiVO4 and NiFe-LDH/BiVO4 photoanodes by factors of 4.9 and 4.3, respectively. Furthermore, it exhibits significantly higher applied bias photon-to-current efficiency (ABPE) and incident photon-to-current efficiency (ICPE) compared to pristine BiVO4 and its binary counterparts. This enhancement in PEC performance is ascribed to the formation of a CdS/BiVO4 heterojunction and the presence of a NiFe-LDH OER co-catalyst, which synergistically facilitate charge separation and transfer efficiencies. The findings suggest that dual modification of BiVO4 with CdS and NiFe-LDH is a promising approach to enhance the efficiency of photoanodes for PEC water splitting.
Charge Transport Enhancement in BiVO4 Photoanode for Efficient Solar Water Oxidation

Zhidong Li,Zhibin Xie,Weibang Li,Hafiz Sartaj Aziz,Muhammad Abbas,Zhuanghao Zheng,Zhenghua Su,Ping Fan,Shuo Chen,Guangxing Liang

DOI: https://doi.org/10.3390/ma16093414

IF: 3.4

2023-04-28

Materials

Abstract:Photoelectrochemical (PEC) water splitting in a pH-neutral electrolyte has attracted more and more attention in the field of sustainable energy. Bismuth vanadate (BiVO4) is a highly promising photoanode material for PEC water splitting. Additionally, cobaltous phosphate (CoPi) is a material that can be synthesized from Earth's rich materials and operates stably in pH-neutral conditions. Herein, we propose a strategy to enhance the charge transport ability and improve PEC performance by electrodepositing the in situ synthesis of a CoPi layer on the BiVO4. With the CoPi co-catalyst, the water oxidation reaction can be accelerated and charge recombination centers are effectively passivated on BiVO4. The BiVO4/CoPi photoanode shows a significantly enhanced photocurrent density (Jph) and applied bias photon-to-current efficiency (ABPE), which are 1.8 and 3.2 times higher than those of a single BiVO4 layer, respectively. Finally, the FTO/BiVO4/CoPi photoanode displays a photocurrent density of 1.39 mA cm−2 at 1.23 VRHE, an onset potential (Von) of 0.30 VRHE, and an ABPE of 0.45%, paving a potential path for future hydrogen evolution by solar-driven water splitting.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Medical history in Israel.

J. H. Cassedy

Bulletin of the History of Medicine

Abstract:
Photoelectrochemical Performance Improving Mechanism: Hybridization Appearing at the Energy Band of BiVO 4 Photoanode by Doped Quantum Layers Modification

Yang Li,Xianying Dai,Yuyu Bu,Hanzhi Zhang,Jie Liu,Wenyu Yuan,Xiaohui Guo,Jin‐Ping Ao

DOI: https://doi.org/10.1002/smll.202200454

IF: 13.3

2022-04-01

Small

Abstract:This work develops doped dual‐quantum layers to modify the surface of BiVO4 photoanode. In this system, hybridization appears at the energy band of BiVO4 photoanode by doped dual‐quantum layers modification, inducing photon absorption capacity enhancement and tandem hole ohmic contact route fabrication. Thus, the photoelectrochemical water oxidation performance of the BiVO4 photoanode improves significantly.Surface passivation of the photoelectrode by wide bandgap semiconductor quantum layer is an important strategy to improve work stability and surface state inhibition. However, an inevitable energy barrier is generated during the quantum tunneling process of the photocarriers. To overcome this shortage, a tandem photo‐generated hole transfer route is fabricated on BiVO4 photoanode by doped dual‐quantum layers modification, Ni‐ZnO (5 nm) and Rh‐SrTiO3 (≈10 nm). Modulated photoelectrochemical (PEC), Scanning Kelvin Probe (SKP), and DFT calculation method results indicate that a tandem hole ohmic contact route is formed in the photoanode to reduce the quantum tunneling energy barrier, meanwhile, the photon absorption capacity of BiVO4 is improved after doped quantum layers modification. Both a phenomenal attribute to the energy band hybridization between Ni, Rh 3d orbits in quantum layers with BiVO4 photoanode. Then, the modified BiVO4 photoanode achieves the recoded photocurrent density of 6.47 and 5.18 mA cm–2 (Na2SO3 electrolyte, VRHE = 1.23 V) under simulated sun light (100 mW cm–2 AM 1.5 G) by xenon lamp illumination without and with UV composition cutting down to ≈5%, respectively. Generally, this work will highlight a potential application in the fields of PEC water splitting and photovoltaic conversion for various semiconductor nanomaterials.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Interfacial nitrogen modulated Z-scheme photoanode for solar water oxidation

Shanshan Zhang,Zheng Xing,Ming Ma,Zhenghao Liu,Wei Tang,Sungsoon Kim,Rong Wu,Jiangyu Li,Jong Hyeok Park

DOI: https://doi.org/10.1016/j.jpowsour.2021.230784

IF: 9.2

2022-01-01

Journal of Power Sources

Abstract:The fabrication of heterojunctions with an appropriate energy band alignment is an attractive strategy to achieve highly efficient solar water splitting. Despite unique advantages, conventional type II heterojunctions face the problem of a relatively low redox power of the charge carriers. Although Z-scheme systems can overcome this problem, their introduction to photoelectrochemical (PEC) devices is challenging due to the specific band alignment. Herein, as an example, an ultrathin MoOxNy layer is deposited on the surface of TiO2 nanoarrays via an in situ conversion process, and the optimized MoOxNy/TiO2 sample generates a photocurrent density that is approximately 2.4 times that for pure TiO2. In addition, a similar surface modification leads to 2.5- and 2.6-fold higher photocurrent values for BiVO4 and WO3 nanostructures, respectively. Interestingly, the impedance of the MoOxNy/TiO2 photoanode is larger than that of the pure TiO2 in the dark, while illumination reverses the trend. This phenomenon, combined with the measured flat band positions, suggests a Z-scheme mechanism, which is further supported by surface potential measurements. The nitrogen (N) atoms play a major role in the boosted photoconversion efficiency for the MoOxNy/TiO2 Z-scheme heterojunction, not only enhancing the light sensitivity but, importantly, substantially promoting charge separation.

energy & fuels,materials science, multidisciplinary,electrochemistry,chemistry, physical
High-performance bismuth vanadate photoanodes cocatalyzed with nitrogen, sulphur co-doped ferrocobalt-metal organic frameworks thin layer for photoelectrochemical water splitting

Ligang Xia,Xinsheng Cheng,Liwen Jiang,Yulin Min,Weifeng Yao,Qiang Wu,Qunjie Xu

DOI: https://doi.org/10.1016/j.jcis.2024.01.049

IF: 9.9

2024-01-11

Journal of Colloid and Interface Science

Abstract:In this study, we prepare a highly efficient BiVO 4 photoanode co-catalyzed with an ultrathin layer of N, S co-doped FeCo-Metal Organic Frameworks (MOFs) for photoelectrochemical water splitting. The introduction of N and S into FeCo-MOFs enhances electron and mass transfer, exposing more catalytic active sites and significantly improving the catalytic performance of N, S co-doped FeCo-based MOFs in water oxidation. The optimized BiVO 4 /NS-FeCo-MOFs photoanode exhibits impressive results, with a photocurrent density of 5.23 mA cm −2 at 1.23 V v s. Reversible Hydrogen Electrode (RHE) and an incident photon-to-charge conversion efficiency (IPCE) of 74.4 % at 450 nm in a 0.1 M phosphate buffered solution (pH = 7). These values are 4.84 times and 6.2 times higher than those of the original BiVO 4 photoanode, respectively. Furthermore, the optimized BiVO 4 /NS-FeCo-MOFs photoanode demonstrates exceptional long-term stability, maintaining 96 % of the initial current after five hours.

chemistry, physical
A Novel Z-Scheme Heterojunction for Efficient Photoelectrochemical Water Splitting

Hewei Yuan,Yaozhong Zhang,Zhi Yang,Yanjie Su,Nantao Hu,Min Zeng,Yafei Zhang

DOI: https://doi.org/10.2139/ssrn.4243273

2022-01-01

SSRN Electronic Journal

Abstract:Photoelectrochemical (PEC) water splitting is a promising technology to produce renewable hydrogen, which still faces problems of low photoelectric efficiency and instability. This work introduces a novel Z-scheme heterojunction consisting of BiVO4 thin film and diamond-like carbon (DLC) to the PEC system as a photoanode and achieves an increased PEC water splitting activity. Compared to the pure BiVO4, the BiVO4/DLC heterojunction has an increased photocurrent density from 0.79 mA cm-2 to 2.39 mA cm-2 at 1.23 V vs. RHE, and the IPCE from 4.8% to 23.4%. After 120 mins (180 cycles) of PEC water splitting, the BiVO4/DLC heterojunction retains up to 82.3% of the initial photocurrent density value, while the pure BiVO4 has only 33.99% remaining under the same conditions. Furthermore, the PEC system of BiVO4/DLC reaches the evolution rate of hydrogen of over 0.32 mmol h-1 cm-2, which is much higher than that of its counterparts. We ascribe the enhancement in PEC performance to the Z-scheme heterojunction that greatly promotes carrier mobility and reduces the recombination rate of electron-hole pairs. We also identify that the band bending and depletion layer are the main reasons for the decrease in charge transfer and interface resistance. It is demonstrated that the sp2 carbon phase in DLC acts as a conductive channel to improve the separation and migration efficiency of free carriers, while the sp3 carbon phase provides stable support and passivation effect to the photoanode, thereby leading to an enhancement for both PEC water splitting performance and the long-time stability. This work provides an effective way to improve the BiVO4 photoanode-based PEC water-splitting systems.
Cooperative catalytic behavior of CoS and Bi2S3 nanoparticles on Zr:BiVO4 photoanodes for enhanced photoelectrochemical sulfite oxidation coupled with pharmaceutical pollution degradation

Prabhakarn Arunachalam,Maged N. Shaddad,Mabrook S. Amer,Abdulaziz M. Alsalman,Madhavan Jagannathan,Mabrook S. Amer

DOI: https://doi.org/10.1039/d4en00018h

2024-04-20

Environmental Science Nano

Abstract:Photoelectrocatalysis is a promising advancing technology that converts energy into electricity and purifies the environment. A photoelectrochemical reaction (PEC) that splits water and degrades pharmaceutical pollutants can be achieved using bismuth vanadate (BiVO4). The water oxidation dynamics of BiVO4 photoanodes are sluggish due to poor charge separation. In this paper, we show that nanoparticles bismuth sulfide (Bi2S3) and cobalt sulfide (CoS) have a cooperative effect on Zr-doped BiVO4 electrodes (Zr:BiVO4) fabricated via PEC techniques. PEC water splitting results reveal that optimal Zr:BiVO4@Bi2S3-CoS films have a photocurrent response of 3.09 mA/cm2 at 1.23 V vs RHE, which is three times better than Zr:BiVO4 films. As a result of combining the above features, Zr:BiVO4@Bi2S3/CoS electrodes achieved 1.53 % applied bias photon-to-current efficiency (ABPE), with a substantial reduction in photocurrent onset potential. Additionally, the composite photoanode demonstrated superior performance in the PEC degradation of tetracycline hydrochloride (TCH) over previously published results. In PEC, Zr:BiVO4@Bi2S3/CoS yielded the most efficient degradation of TCH (94%), six times more than Zr:BiVO4 and EC (55%).The present study presents a visible light-responsive, efficient, sustainable water splitting technique for producing hydrogen, as well as new insights into wastewater treatment.

environmental sciences,chemistry, multidisciplinary,nanoscience & nanotechnology
New BiVO4 Dual Photoanodes with Enriched Oxygen Vacancies for Efficient Solar-Driven Water Splitting

Songcan Wang,Peng Chen,Yang Bai,Jung-Ho Yun,Gang Liu,Lianzhou Wang

DOI: https://doi.org/10.1002/adma.201800486

Abstract:Bismuth vanadate (BiVO4 ) is a promising photoanode material for photoelectrochemical (PEC) water splitting. However, owing to the short carrier diffusion length, the trade-off between sufficient light absorption and efficient charge separation often leads to poor PEC performance. Herein, a new electrodeposition process is developed to prepare bismuth oxide precursor films, which can be converted to transparent BiVO4 films with well-controlled oxygen vacancies via a mild thermal treatment process. The optimized BiVO4 film exhibits an excellent back illumination charge separation efficiency mainly due to the presence of enriched oxygen vacancies which act as shallow donors. By loading FeOOH/NiOOH as the cocatalysts, the BiVO4 dual photoanodes exhibit a remarkable and highly stable photocurrent density of 5.87 mA cm-2 at 1.23 V versus the reversible hydrogen electrode under AM 1.5 G illumination. An artificial leaf composed of the BiVO4 /FeOOH/NiOOH dual photoanodes and a single sealed perovskite solar cell delivers a solar-to-hydrogen conversion efficiency as high as 6.5% for unbiased water splitting.
Interfacial Engineering‐Assisted Energy Level Modulation Enhances the Photoelectrochemical Water Oxidation Performance of Bismuth Vanadate Photoanodes

Kaige Tian,Zhuo Xu,Hua Yang,Guilin Chen,Pengfei An,Jing Zhang,Shengzhong (Frank) Liu,Junqing Yan

DOI: https://doi.org/10.1002/aenm.202404477

IF: 27.8

2024-11-18

Advanced Energy Materials

Abstract:A novel hole transport layer of CuCrO2 has been applied to the surface of the BiVO4 photoanode, promoting the separation of photogenerated carriers. Under the surface NiCo‐MOF reaction sites, the new MOF/CuCrO2/BiVO4 shows excellent photoelectrochemical water oxidation performance. BiVO4 faces significant challenges for widespread application in photoelectrochemical (PEC) water oxidation due to its poor hole transport ability, high surface defect density, and sluggish water oxidation reaction kinetics. Employing interfacial engineering to assist in energy level modulation is an effective strategy to address these challenges. Herein, a CuCrO2 hole transport layer (HTL) is coupled and further grew NiCo‐MOF in situ to prepare a NiCo‐MOF‐CuCrO2‐BiVO4 composite photoanode. The novel composite photoanode not only achieves a photocurrent density of 5.75 mA cm−2 at 1.23 V versus a reversible hydrogen electrode (vs RHE) but also maintains stable operation for over 24 h. Comprehensive physicochemical characterization and density‐functional theory calculations confirm that the built‐in electric field generated by the p–n heterojunction formed between the CuCrO2 HTL and BiVO4 photoanode enhances the hole transport ability. Moreover, the NiCo‐MOF chelated on the photoanode surface not only passivates the surface defect states but also accelerates the kinetics of the water oxidation reaction. Under the synergistic effect of dual modification, the PEC water oxidation performance of the BiVO4 photoanode is dramatically improved. This pioneering work presents a MOF/HTL/BiVO4 configuration that provides a blueprint for the future development of integrated photoanodes for efficient solar energy conversion.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,energy & fuels

Random dynamical systems generated by stochastic Navier–Stokes equations on a rotating sphere

Z-schematic Water Splitting by the Synergistic Effect of a Type-Ii Heterostructure and a Highly Efficient Oxygen Evolution Catalyst

Integration of surficial oxygen vacancies and interfacial two-dimensional NiFe-layered double hydroxide nanosheets onto bismuth vanadate photoanode for boosted photoelectrochemical water splitting

Systematic engineering of BiVO4 photoanode for efficient photoelectrochemical water oxidation

Efficient Solar Water Splitting via Enhanced Charge Separation of the BiVO 4 Photoanode

Decoration of BiVO4 Photoanodes with Near-Infrared Quantum Dots for Boosted Photoelectrochemical Water Oxidation

Decoration of BiVO 4 Photoanodes with Near-Infrared Quantum Dots for Boosted Photoelectrochemical Water Oxidation

Interface-engineered dual Z-scheme of BiVO4/NH2-MIL-125(Ti)/POF photoanode with enhanced photoelectrochemical performance

Synergistic Surface Engineering of BiVO4 Photoanodes for Improved Photoelectrochemical Water Oxidation

Interface Modulation of BiVO4 Based Photoanode with Bi(III)Bi(V)O4 for Enhanced Solar Water Splitting

Nanostructured BiVO4 Photoanodes Fabricated by Vanadium-infused Interaction for Efficient Solar Water Splitting

Promoting the Photoelectrochemical Properties of BiVO4 Photoanode via Dual Modification with CdS Nanoparticles and NiFe-LDH Nanosheets

Charge Transport Enhancement in BiVO4 Photoanode for Efficient Solar Water Oxidation

Medical history in Israel.

Photoelectrochemical Performance Improving Mechanism: Hybridization Appearing at the Energy Band of BiVO 4 Photoanode by Doped Quantum Layers Modification

Interfacial nitrogen modulated Z-scheme photoanode for solar water oxidation

High-performance bismuth vanadate photoanodes cocatalyzed with nitrogen, sulphur co-doped ferrocobalt-metal organic frameworks thin layer for photoelectrochemical water splitting

A Novel Z-Scheme Heterojunction for Efficient Photoelectrochemical Water Splitting

Cooperative catalytic behavior of CoS and Bi2S3 nanoparticles on Zr:BiVO4 photoanodes for enhanced photoelectrochemical sulfite oxidation coupled with pharmaceutical pollution degradation

New BiVO4 Dual Photoanodes with Enriched Oxygen Vacancies for Efficient Solar-Driven Water Splitting

Interfacial Engineering‐Assisted Energy Level Modulation Enhances the Photoelectrochemical Water Oxidation Performance of Bismuth Vanadate Photoanodes