Abstract:Rubber-steel-layered structures are used in many engineering applications. Laminated rubber-steel bearing, as a type of seismic isolation device, is one of the most important applications of the rubber-steel-layered structures. Interfacial debonding in rubber-steel-layered structures is a typical failure mode, which can severely reduce their load-bearing capacity. In this paper, the authors developed a simple but effective active sensing approach using embedded piezoceramic transducers to provide an in-situ detection of the interfacial debonding between the rubber layers and steel plates. A sandwiched rubber-steel-layered specimen, consisting of one rubber layer and two steel plates, was fabricated as the test specimen. A novel installation technique, which allows the piezoceramic transducers to be fully embedded into the steel plates without changing the geometry and the surface conditions of the plates, was also developed in this research. The active sensing approach, in which designed stress waves can propagate between a pair of the embedded piezoceramic transducers (one as an actuator and the other one as a sensor), was employed to detect the steel-rubber debonding. When the rubber-steel debonding occurs, the debonded interfaces will attenuate the propagating stress wave, so that the amplitude of the received signal will decrease. The rubber-steel debonding was generated by pulling the two steel plates in opposite directions in a material-testing machine. The changes of the received signal before and after the debonding were characterized in a time domain and further quantified by using a wavelet packet-based energy index. Experiments on the healthy rubber-steel-layered specimen reveal that the piezoceramic-induced stress wave can propagate through the rubber layer. The destructive test on the specimen demonstrates that the piezoceramic-based active sensing approach can effectively detect the rubber-steel debonding failure in real time. The active sensing approach is often used in structures with "hard" materials, such as steel, concrete, and carbon fiber composites. This research lays a foundation for extending the active sensing approach to damage detection of structures involving "soft" materials, such as rubber.

Inspecting epoxy layer defects in steel-epoxy-steel sandwich structures using guided waves

Ultrasonic Guided Wave-Based Circumferential Scanning of Plates Using a Synthetic Aperture Focusing Technique

Ultrasonic Guided Wave Approach Incorporating SAFE for Detecting Wire Breakage in Bridge Cable

Research on Ultrasonic Guided Wave Dispersion Compensation for Steel Strand Defect Detection

Evaluation of Pipe Axial Defeat Through the Use of Ultrasonic Guided Wave and Matching Pursuit

Ultrasonic Full Guided Wavefield for Damage Detection in Curved CFRP Parts

Non-destructive Evaluation of Spiral-welded Pipes Using Flexural Guided Waves

Multiphysics Structured Eddy Current and Thermography Defects Diagnostics System in Moving Mode.

Imaging and Testing of Ultrasonic Sh Guided Waves in Plate with Lap Welding Structure

Guided Waves Methods for Local Damage Assessments in Steel Structural Members

Detection of sleeve grouting connection defects in fabricated structural joints based on ultrasonic guided waves

Evaluation of Defect Detection in Aluminium, CFRP and Epoxy Resin Plates Using Non-contact Air-Coupled Ultrasonic Waves

Review of wave method-based non-destructive testing for steel-concrete composite structures: Multiscale simulation and multi-physics coupling analysis

Investigation of the Mechanism of Hidden Defects in Epoxy Asphalt Pavement on Steel Bridge Decks Under Moisture Diffusion Using Nondestructive Detection Techniques

Delamination Detection in Composite Plates Using Linear and Nonlinear Ultrasonic Guided Waves

Application of Impact Imaging Method on Nondestructive Detection of Void Defects in Sandwich-Structured Immersed Tunnel

Research on Crossing-Pipe Support Structure Defect Detection of EMAT-Excited CSH Wave

Detection of Interfacial Debonding in a Rubber-Steel-Layered Structure Using Active Sensing Enabled by Embedded Piezoceramic Transducers

A combined inspection technique for debonding defects in CFRP-strengthened steel structures based on leaky Lamb wave and low-power vibrothermography

Debonding Detection in Grouted Sleeves Using Axisymmetric Longitudinal Guided Waves

Application Of Guided Wave Propagation In Diagnostics Of Steel Bridge Components