The IDF Diabetes Atlas: providing evidence, raising awareness and promoting action.

N. Unwin,D. Gan,D. Whiting

DOI: https://doi.org/10.1016/j.diabres.2009.11.006

IF: 8.18

Diabetes Research and Clinical Practice

Abstract:

What problem does this paper attempt to address?

Effect of recirculation zones on the ventilation of a public washroom

Krishnendu Sinha,Utkarsh Verma,Janani Srree Murallidharan,Vivek Kumar

DOI: https://doi.org/10.1063/5.0064337

2021-08-24

Abstract:Air-borne transmission can pose a major risk of infection spread in enclosed spaces. Venting the air out using exhaust fans and ducts is a common approach to mitigate the risk. In this work, we study the air flow set up by an exhaust fan in a typical shared washroom that can be a potential hot spot for COVID-19 transmission. The primary focus is on the regions of recirculating flow that can harbor infectious aerosol for much longer than the well-ventilated parts of the room. Computational fluid dynamics is used to obtain the steady state air flow field, and Lagrangian tracking of particles give the spatial and temporal distribution of infectious aerosol in the domain. It is found that the washbasin located next to the door is in a prominent recirculation zone, and particles injected in this region take much longer to be evacuated. The ventilation rate is found to be governed by the air residence time in the recirculation zone, and it is much higher than the time scale based on fully-mixed reactor model of the room. Increasing the fan flow rate can reduce the ventilation time, but cannot eliminate the recirculation zones in the washroom.

Fluid Dynamics
Numerical Comparison of the Efficiency of Mixing Ventilation and Impinging Jet Ventilation for Exhaled Particle Removal in a Model Intensive Care Unit

Lei Wang,Xiahong Dai,Jianjian Wei,Zhengtao Ai,Yifan Fan,Lingling Tang,Tao Jin,Jian Ge

DOI: https://doi.org/10.1016/j.buildenv.2021.107955

IF: 7.093

2021-01-01

Building and Environment

Abstract:Effective infection prevention and control measures are required in the intensive care units of hospitals, as these areas have a high incidence of nosocomial infections. Adopting proper ventilation pattern that is efficient in pollutant removal is important for controlling the spread of infectious diseases. In this study, the computational fluid dynamics (CFD) simulation approach is used to investigate the airflow pattern, fates of respiratory particles, and patients' intake fraction in a four-bed model intensive care unit under three types of ventilation: impinging jet ventilation and two forms of mixing ventilation. The results show that in contrast to mixing ventilation, the airflow trend of impinging jet ventilation is consistent with the thermal plume of the human body. Accordingly, impinging jet ventilation can efficiently remove pollutants at the ceiling level, thereby reducing cross-infection. Our results also show that fine particles are greatly affected by the ventilation pattern, whereas large particles are primarily removed by surface deposition. The maximum intake fraction of susceptible patients under the three types of ventilation are 8.24 x 10-5 (impinging jet ventilation); 4.5 x 10-4 (ceiling air ventilation; a type of mixing ventilation) and 5.3 x 10-4 (side air ventilation; a type of mixing ventilation). Impinging jet ventilation appears to be the most effective ventilation system for removing particles and reducing susceptible patients' intake fraction under our investigated scenarios, and exhibits great potential as a ventilation method in intensive care units.
CFD Investigation of Ventilation Strategies to Remove Contaminants from a Hospital Room

Mustafa Alkhalaf,Adrian Ilinca,Mohamed Yasser Hayyani

DOI: https://doi.org/10.3390/designs7010005

2023-01-04

Designs

Abstract:The primary requirement in designing air conditioning systems in healthcare facilities is eliminating contaminants. It is considered one of the crucial health elements in building design, particularly in the presence of many airborne diseases such as COVID-19. The purpose of this numerical research is to simulate various ventilation designs for a hospital room model by taking into account results obtained by previous researchers. Four designs with three airflows, 9, 12, and 15 ACH (Air Change per Hour), are applied to explore the capacity of the ventilation system to remove contaminants. The objective is to determine the influence of airflow and the diffuser location distribution on the pollutants elimination represented by carbon dioxide. The Reynold Averaged Navier–Stokes (RANS) equations and the k-ε turbulence model were used as the underlying mathematical model for the airflow. In addition, boundary conditions were extracted from ASHRAE (American Society of Heating, Refrigeration, and Air-Conditioning Engineers Society) ventilation publications and relevant literature. Contrary to what was expected, this study’s results demonstrated that increased ventilation alone does not always improve air distribution or remove more contaminants. In addition, pollutant removal was significantly affected by the outlet’s location.
Optimizing indoor air quality: CFD simulation and novel air cleaning methods for effective aerosol particle inhibition in public spaces

Chao-Long Geng,Xu-Yanran Zhu,Ning Chen

DOI: https://doi.org/10.1007/s11356-023-30832-x

Abstract:In contemporary building ventilation, displacement and mixing ventilation demand high air volumes for rapid virus elimination, resulting in elevated energy consumption. To minimize the spread of viruses and decrease energy consumption for ventilation, this study employed CFD to explore the efficacy of a downward uniform flow field in impeding the transmission of aerosol particles in a high-traffic public facility, like a supermarket. The findings indicate that the downward uniform flow field proves insufficient when individuals remain static for extended periods. A wind speed of 0.1 m/s or higher becomes essential to overpower the stationary thermal plume, which disrupts this flow field. In areas with human presence, however, this technique is found to be particularly efficient since mobile heat sources do not generate a fixed thermal plume. A 0.05 m/s downward uniform flow field can settle 90% of particles within just 22 s. This flow pattern contributes to the swift settling of aerosol particles and effectively diminishes their dispersion. Employing this flow pattern in public places with increased foot traffic, like supermarkets, can lower the risk of contracting novel coronavirus without augmenting energy consumption. In order to implement the flow field in a part of the domain, a new air purification device is proposed in this study. The device combined with shelves can optimize the flow field uniformity through the MLA (PSO-SVR) algorithm and alteration of the air distribution structure. The uniformity of the final flow field increased to 0.925. The combination of data-driven MLA with CFD showed good performance in predicting the flow field uniformity. These findings offer valuable insights and practical applications for the prevention and control of respiratory diseases, particularly in post-epidemic scenarios.
Study on the infection control performance under interactive cascade ventilation: A focus on a conference room environment

Han Li,Qiuyue Cui,Xiangfei Kong,Man Fan

DOI: https://doi.org/10.1016/j.buildenv.2024.111161

IF: 7.093

2024-01-06

Building and Environment

Abstract:With the rise of respiratory infectious diseases, many scholars focus on finding an appropriate ventilation method to effectively improve the indoor environmental protection effect, especially for crowded spaces, which can cause a widespread spread of the epidemic. Interactive cascade ventilation (ICV), as a recently proposed ventilation method, has presented advantages in thermal comfort, infection control and energy consumption. This study discusses the effect of the outlet/inlet locations on infection control performance under interactive cascade ventilation in a conference room with an experimentally verified model. Ninety-five simulations are carried out by considering changes in the location of the outlet/inlet opening and infection source. Particle removal efficiency ( ε ), predicted infection risk ( Pi ) and contaminant dispersion index ( CDI ) are introduced to evaluate the infection control performance comprehensively. The simulation results show that double-side supply air outlets coupled with double-side return air inlets can reduce Pi by 51.1 % compared with other ventilation strategies investigated in this paper. It indicates that ventilation zoning design is more effective for reducing cross-infection in dense spaces. The findings in this study can efficiently provide new insights for the actual application of ventilation strategies in conference rooms under epidemic normalization.

engineering, environmental,construction & building technology, civil
Optimization of Bathroom Ventilation Design for an Iso Class 5 Clean Ward

Caiqing Yang,Xudong Yang,Tengfang Xu,Luchun Sun,Wei Gong

DOI: https://doi.org/10.1007/s12273-009-9310-1

IF: 4.0083

2009-01-01

Building Simulation

Abstract:Ventilation is a main method to control the contaminant dispersion within clean wards. In this paper, we investigated the effects of various ventilation designs of the bathroom in an ISO Class 5 clean ward. Specifically, the contaminant dispersion and particle concentrations corresponding to three different ventilation design schemes were characterized and compared using computational fluid dynamics (CFD) analysis. For each design, we examined airflow and particle concentrations for contaminant sources located at two places (i.e., at the toilet seat and on the floor), respectively. Field test was conducted to compare the measured and simulated air velocities and particle concentrations in a hospital clean ward. The implemented CFD modeling of ventilation effects of various designs in this study has proven to accurately characterize airflow and contaminant control in the ventilated space, and has led to optimizing ventilation for the bathroom in an ISO Class 5 clean ward.
Numerical investigation of airborne transmission in low-ceiling rooms under displacement ventilation

Changchang Wang,Jiarong Hong

DOI: https://doi.org/10.48550/arXiv.2301.05818

2023-01-14

Abstract:This study employs computational fluid dynamics (CFD) simulations to evaluate the risk of airborne transmission of COVID-19 in low-ceiling rooms, such as elevator cabins, under mechanical displacement ventilation. The simulations take into account the effects of the human body's thermal environment and respiratory jet dynamics on the transmission of pathogens. The results of the study are used to propose a potential mitigation strategy based on ventilation thermal control to reduce the risk of airborne transmission in these types of enclosed indoor spaces. Our findings demonstrate that as the ventilation rate (Qv) increases, the efficiency of removing airborne particles (Ep) initially increases rapidly, reaches a plateau (Ep,c) at a critical ventilation rate (Qc), and subsequently increases at a slower rate beyond Qc. The Qc for low-ceiling rooms is lower compared to high-ceiling rooms due to the increased interaction between the thermal plume generated by the occupants or infectors and the ventilation. Further analysis of the flow and temperature fields reveals that Ep is closely linked to the thermal stratification fields, as characterized by the thermal interface height, the height of the temperature isosurface, and temperature gradient. The simulations also indicate that the location of infector relative to ventilation inlet/outlet affects Qc and Ep,c with higher Qc and lower Ep,c observed when infector is in a corner due to potential formation of a local hot spot of high infection risk when infector is near the ventilation inlet. In conclusion, based on the simulations, we propose a ventilation thermal control strategy, by increasing the ventilation temperature, to reduce the risk of airborne transmission in low-ceiling rooms. Our findings indicate that the thermal environment plays a critical role in the transmission of airborne diseases confined spaces.

Fluid Dynamics,Medical Physics
Ventilation Strategies for Mitigation of Infection Disease Transmission in an Indoor Environment: A Case Study in Office

Chen Ren,Hao-Cheng Zhu,Shi-Jie Cao

DOI: https://doi.org/10.3390/buildings12020180

IF: 3.324

2022-02-04

Buildings

Abstract:During the normalization phase of the COVID-19 epidemic, society has gradually reverted to using building space, especially for public buildings, e.g., offices. Prevention of airborne pollutants has emerged as a major challenge. Ventilation strategies can contribute to mitigating the spread of airborne disease in an indoor environment, including increasing supply air rate, modifying ventilation mode, etc. The larger ventilation rate can inevitably lead to high energy consumption, which may be also ineffective in reducing infection risk. As a critical factor affecting the spread of viral contaminant, the potential of ventilation modes for control of COVID-19 should be explored. This study compared several ventilation strategies in the office, including mixing ventilation (MV), zone ventilation (ZV), stratum ventilation (SV) and displacement ventilation (DV), through analyzing ventilation performance and infection risk for the optimal one. By using ANSYS Fluent, the distributions of airflow and pollutant were simulated under various ventilation modes and infected occupants. The SV showed greater performance in mitigating infection disease spread than MV, ZV and DV, with an air distribution performance index (ADPI) of 90.5% and minimum infection risk of 13%. This work can provide a reference for development of ventilation strategies in public space oriented the prevention of COVID-19.

construction & building technology,engineering, civil
Impact of ventilation efficiency on restraining hazardous toilet plume post-flushing in indoor environments

Hua Liu,Zhonghua Zhang,Yalei Zhang,Xuefei Zhou

DOI: https://doi.org/10.1177/1420326x241262650

2024-06-20

Indoor and Built Environment

Abstract:Indoor and Built Environment, Ahead of Print. This study analyzed the hybrid ventilation efficiency of indoor toilet plumes generated post-flushing with various designs. Single-sided natural ventilation and hybrid ventilation were numerically investigated to determine the impact of vent locations commonly found in multistorey buildings. An in-situ experiment was performed to identify the size distribution of the plume with time series. A computational fluid dynamics model based on the Reynolds-averaged naiver-Stokes equations and baseline k-ω turbulence equations was used to predict aerosol pollutant transmission. The aerosol-laden particles receded gradually impacted by the convection of the ambient source. Besides flush volume, temperature and ventilation scenarios were also related to the generation and droplet transmission. The results indicated that the ventilation rates were generally increased with decreased residence time if the turbulence was not suppressed. This study suggested that appropriate ventilation design could significantly reduce the average particle residence time, in which case it could also reduce the rate of virus infection.

public, environmental & occupational health,engineering, environmental,construction & building technology
Investigation on the contaminant distribution with improved ventilation system in hospital isolation rooms: Effect of supply and exhaust air diffuser configurations

Jinkyun Cho

DOI: https://doi.org/10.1016/j.applthermaleng.2018.11.023

IF: 6.4

2019-02-01

Applied Thermal Engineering

Abstract:This study, that is practice-based learning in a real hospital construction project, has evaluated the ventilation performance of three strategies in the protection of health care workers and HVAC control for airborne infectious diseases induced by contaminated exhaled air from patients in a negative pressure isolation room. This paper examines air flow path and airborne pollutant distribution by computational fluid dynamics modeling and field measurement. In hospitals, the risk of virus diffusion mainly depends on air flow behavior and changes in direction caused by supply air and exhaust air locations. An improved isolation room ventilation strategy has been suggested, and is found to be the most efficient in removing contaminants based on the observations and simulation results from three ventilation systems. The results show that ventilation systems utilizing the "low-level extraction" technique are very effective at removing pollutants in the human breathing zone. A new clean isolation room ventilation strategy has been developed that employs two exhaust air grilles on the wall behind the bed at low floor level, coupled with a fan filter unit, and is found to have the highest pollutant removal efficiency.

energy & fuels,engineering, mechanical,thermodynamics,mechanics
Optimization of ventilation design for indoor air quality by using a new conception-spatial flow influence factor

Xinke Wang,Yinping Zhang,Wei Deng,Xiaofeng Li

2006-01-01

Abstract:A new concept, the spatial flow influence factor (SFIF) was proposed in literature, which provides a new insight into the airflow structure. This concept can be used to predict indoor chemical contaminant concentration, which is verified with the computational fluid dynamic (CFD) in this paper. Based on the concept, some traditional parameters of ventilation assessment are obtained. This concept is very helpful in the control of indoor air pollutants. Two illustrative examples are provided to show (1) how to select the optimal arrangement of the chemical pollutant sources and occupied regions for a given indoor airflow and chemical pollutant sources; (2) how to select better ventilation mode for chemical pollutant sources and occupied regions (or target regions) with given positions.
Indoor Airflow and Pollutant Spread Inside the Cleanroom with Micro-Porous Supplying Panel and Different Ventilation Schemes: Analytical, Numerical and Experimental Investigations

Fu-Yun Zhao,Jin Cheng,Bao Liu,Zhi-Rong Huang,Xianting Li

DOI: https://doi.org/10.1016/j.jobe.2020.101405

IF: 7.144

2020-01-01

Journal of Building Engineering

Abstract:The airflow distribution and human thermal comfort at different supply airflow rates, as well as cleanliness recovery characteristic of indoor pollutant were numerically and theoretically investigated in a Class 10, 000 cleanroom. Computational fluid dynamics models of the cleanroom with three ventilation schemes, where the position of the micro-porous air supplying panel was altered to create unidirectional low-turbulence flow, were built and validated by the on-site measurements that carried out in a full scale test room. The results of theoretical analysis of cleanliness recovery characteristic were compared with numerical ones, to identify whether the decay equation could accurately predict the cleanliness recovery characteristic of different ventilation schemes. It was found that air distribution was generally uniform, and a small temperature gradient was still observed. Air change rate (ACH) played an important role in the indoor airflow field, and particularly it has a distinct effect on the deflection and the distribution of thermal plume (e.g. in the scheme of lateral ventilation). For large ACH, removal of pollutant (e.g. in the scheme of combined ventilation) could be enhanced, whereas there was a risk of thermal discomfort (e.g. in the scheme of vertical ventilation). Furthermore, decay equation was demonstrated that it was not suitable for all ventilation for predicting the cleanliness recovery time. Present work certainly adds to our understanding of the micro-porous panel ventilation in cleanrooms. Present investigation has a number of important implications for future cleanroom practice.
Ventilation reconstruction in bathrooms for restraining hazardous plume: Mitigate COVID-19 and beyond

Ji-Xiang Wang,Zhe Wu,Hongmei Wang,Mingliang Zhong,Yufeng Mao,Yunyun Li,Mengxiao Wang,Shuhuai Yao

DOI: https://doi.org/10.1016/j.jhazmat.2022.129697

2022-10-05

Abstract:Converging evidence reports that the probability of vertical transmission patterns via shared drainage systems, may be responsible for the huge contactless community outbreak in high-rise buildings. Publications indicate that a faulty bathroom exhaust fan system is ineffective in removing lifted hazardous virus-laden aerosols from the toilet bowl space. Common strategies (boosting ventilation capability and applying disinfection tablets) seem unsustainable and remain to date untested. Using combined simulation and experimental approaches, we compared three ventilation schemes in a family bathroom including the traditional ceiling fan, floor fan, and side-wall fan. We found that the traditional ceiling fan was barely functional whereby aerosol particles were not being adequately removed. Conversely, a side-wall fan could function efficiently and an enhanced ventilation capability can have increased performance whereby nearly 80.9% of the lifted aerosol particles were removed. There exists a common, and easily-overlooked mistake in the layout of the bathroom, exposing occupants to a contactless vertical pathogen aerosol transmission route. Corrections and dissemination are thus imperative for the reconstruction of these types of family bathrooms. Our findings provide evidence for the bathroom and smart ventilation system upgrade, promoting indoor public health and human hygiene.
Experimental research on the cross-infection control performance of different ventilation strategies

Han Li,Yuer Lan,Musong Liu,Xiangfei Kong,Man Fan

DOI: https://doi.org/10.1016/j.buildenv.2023.110683

IF: 7.093

2023-08-17

Building and Environment

Abstract:Sustained pandemics have awakened the growing need to select appropriate indoor ventilation strategies to create a healthy environment. Hence, this study experimentally evaluated the cross-infection control performance of different ventilation strategies, namely mixing ventilation with outlets installed in the bottom of the side wall (MV-BR) and at ceilings (MV-CR), stratum ventilation with outlets installed in the side wall (SV-SR) and at ceilings (SV-CR), interactive cascade ventilation with outlets installed in the side wall (ICV-SR) and at ceilings (ICV-CR). The supply air flow rate of the studied ventilation strategies remains the same (6.51 h −1 ) for fair comparison. The infection risk and maximum cumulative exposure are introduced as the evaluation indicators. The research results show that the mean infection risk in the respiratory zone of susceptible individuals who are standing in the sidewind directions of the infected people under ICV-SR has the lowest potential infection risk ( P i ) value of 0.012, which is consistently lower than ICV-CR by 8.3%, MV-CR by 42%, MV-BR by 45%, SV-CR by 50%, and SV-SR by 55%, respectively. And the average max long-term exposure of MV-BR is 15.2% lower than MV-CR. Compared with SV-CR and ICV-CR, SV-SR and ICV-SR can also realize to reduce the max long-term exposure by 21.3% and 25%, respectively. The integrated scenario index calculation results demonstrate that ICV presents excellent cross-infection control performance than SV and MV, obtaining 53.5% and 61.2% lower cross-infection risk. The conclusions got from this study can provide guide for the design of indoor airflow organization with the epidemic normalizing.

engineering, environmental,construction & building technology, civil
Did You Just Cough? Visualization of Vapor Diffusion in an Office Using Computational Fluid Dynamics Analysis

Mohammad Al-Rawi,Ahmed M Al-Jumaily,Annette Lazonby

DOI: https://doi.org/10.3390/ijerph19169928

2022-08-11

Abstract:Awareness of indoor air quality (IAQ) in crowded places such as schools and offices has increased since 2020 due to the COVID-19 pandemic. In addition, countries' shifting away from containment and towards living with COVID-19 is expected to increase demand for risk mitigation via air-purification devices. In this work, we use Computational Fluid Dynamics (CFD) analysis to investigate the impact of adding an air-purification technology on airflow in an enclosed space. We model a Polyester Filter and UV light (PFUV) dehumidifier in an office with two occupants: one infected with an airborne infectious disease, such as COVID-19; and the other uninfected. We compare three cases where the infected occupant coughs: with no device, and with the device at two different orientations. We construct a CFD model using ANSYS® 2021 Fluent and the Discrete Phase Model (DPM) for the particle treatment. Thermal comfort is assessed using the Testo 400 IAQ and comfort kit. We find that both the device operation and the placement alter the airflow contours, significantly reducing the potential for the uninfected occupant to inhale the vapour expelled by the infected occupant, potentially impacting the likelihood of disease transmission. The device improved thermal comfort measured by Predicted Mean Vote (PMV), Predicted Percentage Dissatisfied (PPD).
Simulation of indoor cigarette smoke particles in a ventilated room

Yunfei Song,Quan Yang,Hui Li,Shengnan Shen,Hongbin Chen,Yicang Huang,Guoqing Zhang,Jiayue Wang,Wei Wei

DOI: https://doi.org/10.1007/s11869-021-01057-z

2021-06-25

Abstract:Smoking indoors generally exists in daily life, and highlighting the importance of reducing the hazard from smoke particles to non-smoking occupants is crucial. To quantitatively investigate the flow characteristics in a ventilated room, a computational fluid dynamics (CFD) method is used to assess the velocity, concentration, and inhalation levels of indoor particles using a manikin with a realistic upper respiratory tract. It realizes smoke particles' diffusion simulation from room scale to human upper respiratory tract scale. An experiment is also performed to measure PM<sub>2.5</sub> concentrations. With the increase of a high air change rate per hour (ACH) from zero to 12.32 and 17.14, the indoor particle concentration reduces by 58.5% and 67.9%, the number of inhaled particles decreases by 22.9% and 43.8%, and the particle concentration around the occupant decreases by 10.3% and 17.5%, respectively. It shows that indoor ventilation has a drastic effect on flow characteristics, particle concentrations, and particle outcomes. ACH of 17.14 is found to significantly reduce the particle concentration around the occupant and decrease the number of smoke particles inhaled and remaining indoors. It indicates that the ventilation equipment can reduce the number of smoke particles in the room. There are still 41.3% and 31.9% particles remaining in the room when the ACH is 12.32 and 17.14, which does harm to human health.
Hospital ventilation simulation for the study of potential exposure to contaminants

Carla Balocco

DOI: https://doi.org/10.1007/s12273-011-0019-6

IF: 4.0083

2011-03-01

Building Simulation

Abstract:Airflow and ventilation are particularly important in healthcare rooms for controlling thermo-hygrometric conditions, providing anaesthetic gas removal, diluting airborne bacterial contamination and minimizing bacteria transfer airborne. An actual hospitalization room was the investigate case study. Transient simulations with computational fluid dynamics (CFD), based on the finite element method (FEM) were performed to investigate the efficiency of the existing heating, ventilation and air-conditioning (HVAC) plant with a variable air volume (VAV) primary air system. Solid modelling of the room, taking into account thermo-physical properties of building materials, architectural features (e.g., window and wall orientation) and furnishing (e.g., beds, tables and lamps) arrangement of the room, inlet turbulence high induction air diffuser, the return air diffusers and two patients lying on two parallel beds was carried out. Multiphysics modelling was used: a thermo-fluidynamic model (convection-conduction and incompressible Navier-Stokes) was combined with a convection-diffusion model. Three 3D models were elaborated considering different conditions/events of the patients (i.e., the first was considered coughing and/or the second breathing). A particle tracing and diffusion model, connected to cough events, was developed to simulate the dispersal of bacteria-carrying droplets in the isolation room equipped with the existing ventilation system. An analysis of the region of droplet fallout and the dilution time of bacteria diffusion of coughed gas in the isolation room was performed. The analysis of transient simulation results concerning particle path and distance, and then particle tracing combined with their concentration, provided evidence of the formation of zones that should be checked by microclimatic and contaminant control. The present study highlights the fact that the CFD-FEM application is useful for understanding the efficiency, adequacy and reliability of the ventilation system, but also provides important suggestions for controlling air quality, patients’ comfort and energy consumption in a hospital.

thermodynamics,construction & building technology
A Novel Circulated Air Curtain System to Confine the Transmission of Exhaled Contaminants: A Numerical and Experimental Investigation.

Wang Haixin,Qian Hua,Guangzhou Angel Biosafety Co., Ltd,Zheng Xiaohong

DOI: https://doi.org/10.1007/s12273-020-0667-5

IF: 4.0083

2020-01-01

Building Simulation

Abstract:Air curtain is an efficient device for cutting off airflow and confining contaminants. Inspired by the ability, a circulated air curtain composed of end-to-end plane jets generated by a relay of air pillars is proposed to confine exhaled contaminants in this study. Furthermore, the optimization study of computational fluid dynamics (CFD) is conducted to explore cutting-off performance and find better design parameters under different conditions, i.e., human-curtain distance, enclosure shape, jet velocity from air pillar, and exhalation modes. The multidirectional blockage and vortex-like rotative transmission routes of exhaled airflow are observed when air curtain exists. Results indicate that contaminants are concentrated around the source. The average mole fraction of exhaled contaminants outside air curtain under different human-curtain distance decreases 4.3%–19.6% compared to mixing ventilation with same flux. Shortening the human-curtain distance can improve the performance of air curtain and may change the direction of exhaled airflow. Moreover, It has better performance when the enclosure shape is close to a circle. Higher jet velocity is better for improving the confinement performance, but the trend is not very obvious as velocity increases. For exhalation modes, it is more challenging to control exhaled contaminants for intense exhalation activity (such as coughing) in steady simulation, but results in transient simulation show better performance when coughing only once. These results can provide a reference for the subsequent design and improvement in applying air curtain in hospital wards or other places, especially during the period of flu outbreak.
Quantitative Effects of Supply Air and Contaminant Sources on Steady Contaminant Distribution in Ventilated Space with Air Recirculation

Xiaoliang Shao,Shukui Liang,Xianting Li,Chao Liang,Shuai Yan

DOI: https://doi.org/10.1016/j.buildenv.2020.106672

IF: 7.093

2020-01-01

Building and Environment

Abstract:Identifying the contributions of different influencing factors to indoor air environment is beneficial for seeking measures to improve environmental quality. The independent effect of supply air and contaminant source can be quantified using accessibility index; however, for ventilated rooms with air recirculation devices, the effects of supply air and contaminant source cannot be described directly owing to the effect of air recirculation. In this study, a concise linear expression is derived to establish a correlation between steady contaminant distribution and each of independent supply air and contaminant sources with air recirculation, based on which index of revised accessibility is defined to evaluate the effects of supply air and contaminant sources. The reliability of the proposed method is verified by comparing with simulation result. Two numerical cases, i.e., two air recirculation devices with cleaning efficiency and a recirculated air curtain, are analyzed to study the quantitative effects of supply air and contaminant source. It is discovered that air recirculation devices change the airflow field considerably, and that the purification effect of air recirculation devices with cleaning efficiencies of 0.2 and 0.3 reduces the effects of supply air and contaminant source. The recirculated air curtain reduces the dominant area of air supply inlet, with regional revised accessibility decreasing from 0.69 to 0.54. Air curtain at an appropriate airflow rate significantly reduces the effect of contaminant source at distant areas, with regional revised accessibility decreasing from 1.03 to 0.64. The proposed method is beneficial for evaluating air recirculation in establishing indoor environment.
Dispersion of exhalation pollutants in a two-bed hospital ward with a downward ventilation system

Hua Qian,Yuguo Li,Peter V. Nielsen,Carl E. Hyldgaard

DOI: https://doi.org/10.1016/j.buildenv.2006.03.025

IF: 7.093

2008-03-01

Building and Environment

Abstract:The Centers for Disease Control and Prevention has recommended the use of downward ventilation systems in isolation rooms to reduce the risk of cross-infection from airborne transmissible diseases. The expected airflow pattern of a downward ventilation design would supply cooler and slightly heavier clean air from a ceiling diffuser to push down contaminants, which would then be removed via outlets at floor level. A “laminar” (strictly speaking, unidirectional) flow is expected to be produced to avoid flow mixing and thus reduce cross-infection risk. Experiments were carried out in a full-scale experimental hospital ward with a downward ventilation system to investigate the possibility of applying downward ventilation in a general hospital ward. Two life-sized breathing thermal manikins were used to simulate a source patient and a receiving patient. Computation fluid dynamics was also used to investigate the airflow pattern and pollutant dispersion in the test ward. Based on both experimental and numerical results, the laminar airflow pattern was shown to be impossible to achieve due to turbulent flow mixing and flow entrainment into the supply air stream. The thermal plumes produced above people were found to induce flow mixing. We also studied the effects of the locations of the supply and extraction openings on both the flow pattern and pollutant exposure level in the occupied zone. A number of practical recommendations are suggested.

engineering, environmental,construction & building technology, civil

The IDF Diabetes Atlas: providing evidence, raising awareness and promoting action.

Effect of recirculation zones on the ventilation of a public washroom

Numerical Comparison of the Efficiency of Mixing Ventilation and Impinging Jet Ventilation for Exhaled Particle Removal in a Model Intensive Care Unit

CFD Investigation of Ventilation Strategies to Remove Contaminants from a Hospital Room

Optimizing indoor air quality: CFD simulation and novel air cleaning methods for effective aerosol particle inhibition in public spaces

Study on the infection control performance under interactive cascade ventilation: A focus on a conference room environment

Optimization of Bathroom Ventilation Design for an Iso Class 5 Clean Ward

Numerical investigation of airborne transmission in low-ceiling rooms under displacement ventilation

Ventilation Strategies for Mitigation of Infection Disease Transmission in an Indoor Environment: A Case Study in Office

Impact of ventilation efficiency on restraining hazardous toilet plume post-flushing in indoor environments

Investigation on the contaminant distribution with improved ventilation system in hospital isolation rooms: Effect of supply and exhaust air diffuser configurations

Optimization of ventilation design for indoor air quality by using a new conception-spatial flow influence factor

Indoor Airflow and Pollutant Spread Inside the Cleanroom with Micro-Porous Supplying Panel and Different Ventilation Schemes: Analytical, Numerical and Experimental Investigations

Ventilation reconstruction in bathrooms for restraining hazardous plume: Mitigate COVID-19 and beyond

Experimental research on the cross-infection control performance of different ventilation strategies

Did You Just Cough? Visualization of Vapor Diffusion in an Office Using Computational Fluid Dynamics Analysis

Simulation of indoor cigarette smoke particles in a ventilated room

Hospital ventilation simulation for the study of potential exposure to contaminants

A Novel Circulated Air Curtain System to Confine the Transmission of Exhaled Contaminants: A Numerical and Experimental Investigation.

Quantitative Effects of Supply Air and Contaminant Sources on Steady Contaminant Distribution in Ventilated Space with Air Recirculation

Dispersion of exhalation pollutants in a two-bed hospital ward with a downward ventilation system