Abstract:We have attempted to apply the computer-based finite element analysis (FEA) method to accurately measure the mechanical properties (e.g., hardness and elasticity) of a soft material by an indentation test. First, an axisymmetric model has been developed using commercially available FEA code ANSYS. The FEA model consisted of a thin Al-film resting on Si-substrate. A spherical indenter has been used to indent the Al-film, which traveled a predefined depth during the loading and unloading cycles. First, numerical simulations were conducted to get the force vs. displacement plot, which was later used to determine the modulus of elasticity and hardness of Al-film. The effects of substrate modulus and indentation depth were thoroughly investigated to determine the modulus and hardness of Al-film. The effect of friction, considered at the interface of indenter and Al-film, was found to offer minimum impact for relatively small indentation depth. The induced force on the Al-film by the indenter has been found to be higher with increasing indentation depth when friction was considered. However the contact stiffness, represented by the slope of the unloading curve, has been found almost the same with and without considering friction. The variation of substrate modulus has been found to be ineffective to capture the Al-film modulus for relatively small indentation depth. However for higher indentation depth, the substrate modulus has been found to offer profound effect to capture the film modulus. The hardness of the Al-film has also been found to be relatively unaffected with variation of substrate modulus. However, the hardness of the Al-film has been found to be higher with friction for relatively high indentation depth. Results obtained from this preliminary research are important to continue further investigation and to characterize the mechanical properties of other soft-materials, e.g., biofilms to minimize its detrimental effects and utilize its favorable aspects in industrial and biomedical applications.

An ion-implantation model incorporating damage calculations in crystalline targets

Design, Expression and Solid-State Nmr Characterization of Silk-Like Materials Constructed from Sequences of Spider Silk, Samia Cynthia Ricini and Bombyx Mori Silk Fibroins

Nanostructure and Mechanical Measurement of Highly Oriented Lamellae of Melt-Drawn HDPE by Scanning Probe Microscopy

Measurement of the elastic modulus of spider mite silk fibers using atomic force microscopy

In Situ Nanoindentation Mechanical Property of Films by Atomic Force Microscope

Nanoconfinement Controls Stiffness, Strength and Mechanical Toughness of Β-Sheet Crystals in Silk

Light-Response Quantitative Trait Loci Identified with Composite Interval and eXtreme Array Mapping in Arabidopsis thaliana Sequence data from this article have been deposited with the EMBL/GenBank Data Libraries under accession nos. AY394847 and AY466496.

Nanoscale optical and structural characterisation of silk

Study of Mechanical Properties of the Spider Silk Using a Micro-Tensile System and DIC Methods

The Cribellate Nanofibrils of the Southern House Spider: Extremely Thin Natural Silks with Outstanding Extensibility

Atomic force microscopy-based nanoindentation technique for characterizing the transverse and shear moduli of flax fibers

Artificial Spider Silk with Buckled Sheath by Nano‐Pulley Combing

Protein secondary structure in spider silk nanofibrils

Mechanical Characterization Device For In Situ Measurement Of Nanomechanical Properties Of Micro/Nanostructures

Carbon Nanotube Fibers: Monitoring a Micromechanical Process in Macroscale Carbon Nanotube Films and Fibers (adv. Mater. 5/2009)

A New Micro-Tensile System for Measuring the Mechanical Properties of Low-Dimensional Materials - Fibers and Films

Nanoindentation of Soft Biological Materials

Nano-Indentation for Characterizing Mechanical Properties of Soft Materials

Nanoscale Probing of Electron-Regulated Structural Transitions in Silk Proteins by Near-Field IR Imaging and Nano-Spectroscopy

Mechanical characterization of biocompatible thin film materials by scanning along micro-machined cantilevers for micro-/nano-system

Probing the Effects of Nanoscale Architecture on the Mechanical Properties of Hexagonal Silica/Polymer Composite Thin Films