Abstract:The HTR-10 is a pebble bed High-temperature gas-cooled reactor (HTGR) with a nominal thermal power of 10 MW. The on-line nondestructive burn-up (BU) measurement for the spherical fuel elements with TRISO coated fuel particles is an important issue in the fuel management of the HTR-10. The HTR-10 employs an HPGe gamma spectroscopy system to determine the BU values of the discharged fuel elements, and the accuracy of the BU measurement system is a crucial issue. The calibration requirement and the absolute calibration method are discussed and analyzed in this paper. In this work, the long-lived fission product 137Cs is demonstrated as the best BU indicator in the HTR-10, whereas the inner-calibrating source method using the ratio of the amounts of 134Cs to 137Cs is not suitable. The BU value of a fuel element is proportional to the intensity of 137Cs gamma-ray and independent on the irradiation history of the fuel element, except for a small correction term related to the radioactive decay of 137Cs. The efficiency of the measurement system is calibrated by using a 137Cs standard source embedded into the center of a graphite sphere with the same size and the same graphite material as the fuel element, which was located at the measurement position of the fuel sphere, to eliminate the possible systematic errors from the measurement system. The difference in geometry and self-absorption between the BU measurement and the calibration measurement is corrected by applying the MCNP simulation. The error sources of the calibration results are analyzed, in which the uncertainty of the source activity (∼5%) is found to dominate. The other major error sources include the fluctuation of the uranium loading in the fuel elements, the errors of the nuclear data, the counting errors of the detector, and the correction procedure for the detection efficiency. More than 1,900 fuel elements discharged from the HTR-10 have been measured by far, and the BU values of these elements spread in the range from 8.4±0.5 GWD/t to 20±1.0 GWD/t, where the relative errors of the burn-ups consist of the calibration errors about 5.2% and the counting errors around the order of 1%. The behavior of the measured burn-ups has been discussed qualitatively.

Analysis of gamma spectra from burnup measurement in HTR-10

Burn-Up Calibration and Error Analysis of Htr-10 Spherical Fuel Elements by Gamma Spectroscopy

A Comprehensive Study of the 14C Source Term in the 10 MW High-Temperature Gas-Cooled Reactor

A Comparison Study on the Burnup of HTR-10 Fuels Using Radiometric and Mass Spectrometric Methods

Study of the burnup measurement for 10 MW high temperature

Simulation of HTR 10 anti Compton hpge gamma ray spectrometer with geant4

Isotopic Measurement of HTR-10 Irradiated Fuels Based on Anti-Compton Gamma Spectroscopic Method

Burnup Measurement Study and Prototype Development in HTR-PM

Novel burnup measurement system via anti-compton techniques for HTR-10

Research and Measure of Tritium and Carbon 14 in HTR 10

Fuel Management of the HTR-10 Including the Equilibrium State and the Running-in Phase

Experimental Study on the Content and Distribution of Key Nuclides in an Irradiated Graphite Sphere of HTR-10

The Application of the DEM-based Burnup Construction Method in the Pebble Burnup History Analysis in HTR-10

Error Analysis and Experimental Research of HTR-10 Burnup Measurement System

Fuel Management of HTR-10

Monte Carlo Studies on the Burnup Measurement for the High Temperature Gas Cooling Reactor

Experiment and Analysis of Fission Product Activity in Primary-Loop of 10 MW High-Temperature Gas-Cooled Reactor

Design and Manufacture of the Fuel Element for the 10 MW High Temperature Gas-Cooled Reactor

Analysis of Influence of Decay-Cooling Time on On-Line Burnup Measurement of HTR-PM

Source Term Analysis of the Irradiated Graphite in the Core of HTR-10

Experimental Investigation of 14C in the Primary Coolant of the 10 MW High Temperature Gas-Cooled Reactor