Abstract:The unique physical and chemical properties of CuO nanostructures make them as the key materials for the application of nano-optoelectronic devices,gas sensors and photodetectors.Although thermal oxidation is a simple,high efficient and low-cost preparation method,the cracking problem caused by heating still limits its wide application in nano-devices.Therefore,it is still necessary to develop the preparation techniques,which can grow CuO nanostructures directly on various substrates,especially the widely-used Si wafer.Photoluminescence (PL) is a nondestructive technique to explore the optical properties and investigate the electronic transitions in semiconductors,which is important to develop the photo-electronic devices.This research is important to promote the practical applications of CuO nanostructures in functional devices.In this work,Cu films with different morphologies are firstly achieved from two different direct current (DC) and radio frequency (RF) magnetron sputtering method.Then,the electric field assisted thermal oxidation method is introduced to grow CuO nanostructures from Cu films.Two different thermal oxidation processes are used to explore the effect of the electric field directions.Besides,Cu foils are also oxidized in the same condition for comparison.The morphologies and crystal structures of Cu films and CuO nanostructures synthesized in different technologies are characterized via scanning electron microscope (SEM),X-ray diffraction (XRD),and transmission electron microscope (TEM).Finally,PL spectra of CuO nanorods are also measured at room temperature by Horiba FluoroMax-4 fluorescence spectrometer.The results show that a columnar Cu film with the thickness of 1.25 μm is obtained from DC magnetron sputtering,whose preferred orientation is (111) plane.CuO nanowires are found on the Cu foils oxidized under two heating conditions.However,for the columnar Cu films,CuO nanorods are only obtained under an upward electric field,which is same to the growth direction of the nanorods.A layer structure of CuO nanorods/CuO layer/Si substrate is formed after thermal oxidation,and it is found exfoliated from the Si substrate.So,a thin Cr buffer layer of about 100 nm is deposited before Cu layer to enhance the film-substrate bonding force.It turns out that the Cr layer can solve the cracking problem caused by thermal stress.The TEM results show that the CuO nanorod is a monocrystal monoclinic phase with diameter of about 40 nm.Besides,the lattice spacings of the CuO nanorod are bigger than the standard spacings.As for the RF magnetron sputtering,although fine grain Cu film of about 0.5 μm is successfully obtained on Si substrate,no one-dimensional nanostructured oxides are found after two thermal oxidation conditions.The most close-packed plane of FCC Cu structure is (111) plane,whose surface energy is minimum.Therefore,it is easier for the film deposited by DC magnetron sputtering to grow along the (111) plane due to the smaller ion energy compared with the RF magnetron sputtering.Furthermore,the DC-deposited columnar Cu film are easier to form CuO nanorods than the RF-deposited fine grain Cu film,because the cracks among columnar crystals provide a high diffusion rate channel for the diffusion of ions.No Cu2O phase is found in this work due to the limited supply of Cu compared with the Cu foils.The CuO nanorods excited with ultraviolet light show wide dark violet to bright blue luminescence band in the range from 390 to 470 nm at room temperature.This study is beneficial to further understand the growth mechanism and optical properties of CuO nanorods and assemble novel functional devices based on Si-CuO nano-arrays.

Impact of Cu doping on the structural, morphological and optical activity of V2O5 nanorods for photodiode fabrication and their characteristics

Effect of Cu Additions on Morphology and Optical Properties of ZnO Nanorod Arrays by Two-Step Method

Structural, optical and electrical properties of pure and Fe doped V2O5 nanoparticles for junction diode fabrications

Fabrication of V-Doped TiO2 Nanoparticles and Photocatalytic Studies under Visible Light

UV Luminescence Enhancement of Cu-doped ZnO Nanorods Grown by Hydrothermal Treatment

Modulation of Magnetic and Luminescence Properties via Control Cu-Doped in CdWO 4 Nanorods for Photocatalytic Applications

Synthesis, characterization, computational studies, and photocatalytic properties of Cu doped Bi2S3 nanorods

Synergistic Effect of V/N Codoping by Ion Implantation on the Electronic and Optical Properties of Tio2

Insight into Copper Doping Ratio on Optoelectronics Performance of Two-Dimensional Cu-Doped SnO 2 Nanosheets: an Experiment and DFT Study

Effect of vanadium doping on the structural and optical characteristics of nano ZnCdS

Doping of nanostructured Cu2O films to improve physical and photoelectrochemical properties as a step forward for optoelectronics applications

Structural, morphological, and optoelectronic characteristics of Zn, Cd-co-doped CuO nanostructures

Facile Synthesis and Optical Properties of Ultrathin Cu-Doped Znse Nanorods

Impact of Co and Cu co‐doping on the Structural, Electrical, Magnetic and Solar Light Driven Photo‐Catalytic Properties of NiFe2O4 Nano‐crystals for Crystal Violet Dye Removal

From Cu2S nanocrystals to Cu doped CdS nanocrystals through cation exchange: controlled synthesis, optical properties and their p-type conductivity research

Synthesis of Cu2+ doped ZnO@ZnCdS thin film: Optical and electrochemical characterization

The effects of Ni/Cu co-doped ZnO nanorods: structural and optoelectronic study

Synthesis and photoluminescence properties of thermal oxidized CuO nanorods from sputtered Cu films

Synthesis And Optical Properties Of V2o5 Nanorods

Synthesis and optical properties of nanorods

Standardizing the optimal photo-diode performance of CuO nanostructures through various morphological patterns