Control of an epidemic spread of a multi-resistant strain ofAcinetobacter calcoaceticus in a hospital

W. Crombach,L. Dijkshoorn,M. Noort-Klaassen,J. Niessen,G. Knippenberg-Gordebeke

DOI: https://doi.org/10.1007/BF01058568

IF: 38.9

Intensive Care Medicine

Abstract:

What problem does this paper attempt to address?

An FPGA-based Timing and Control System for the Dynamic Compression Sector

Shefali Saxena,Daniel R. Paskvan,Nicholas R. Weir,Nicholas Sinclair

DOI: https://doi.org/10.1063/5.0081205

2021-12-06

Abstract:A field programmable gate array (FPGA) based timing and trigger control system has been developed for the Dynamic Compression Sector (DCS) user facility located at the Advanced Photon Source (APS) at Argonne National Laboratory. The DCS is a first-of-its-kind capability dedicated to dynamic compression science. All components of the DCS laser shock station - x-ray choppers, single-shot shutter, internal laser triggers, and shot diagnostics-must be synchronized with respect to the arrival of x-rays in the hutch. A field-programmable gate array (FPGA) synchronized to the APS storage ring radio frequency (RF) clock (352 MHz) generates trigger signals for each stage of the laser and x-ray shutter system with low jitter. The system is composed of a Zynq FPGA, a debug card, line drivers and power supply. The delay and offsets of trigger signals can be adjusted using a user-friendly graphical user interface (GUI) with high precision. The details of the system architecture, timing requirements, firmware, and software implementation along with the performance evaluation are presented in this paper. The system offers low timing jitter (15.5 ps r.m.s.) with respect to APS 352 MHz clock, suitable for the 50 ps r.m.s. x-ray bunch duration at the APS.

Instrumentation and Detectors
Digital phase control system for ssrf linac

C. X. Yin,D. K. Liu,L. Y. Yu

2008-01-01

Abstract:In order to reach the requirement of RF phase stability, digital phase control system is implemented in SSRF (Shanghai Synchrotron Radiation Facility) LINAC, which has already operated since May 2007. FPGA is the key of digital phase control system, which contains digital I/Q demodulator (phase detector), digital I/Q modulator (phase shifter) and control algorithms. With the aid of FPGA, the whole period of closed-loop is about 40ns, and delay of closed-loop is about 1us. The preliminary testing result was presented in this paper.
A Multi-Channel Digital Programable Delay Trigger System with High Accuracy and Wide Range

Changxing Lin,Beibei Shao,Jian Zhang

DOI: https://doi.org/10.1109/icecc.2011.6067688

2011-01-01

Abstract:This paper presents a multi-channel Digital Programmable Delay Trigger System (DPDTS) with high accuracy and wide delay range, which can be widely used in laser system and electron accelerator. This DPDTS mainly makes up of reference clock module, user interface and control module and Digital Programmable Delay Trigger (DPDT) module which is implemented on a Xilinx V6LX75T FPGA. In this DPDTS, DDS algorithm is used in frequency control, while soft microprocessor MicroBlaze is instanced for user interface control. Time delay is separated into wide range coarse delay and narrow range fine delay. Wide range coarse delay is achieved through counter, while narrow range fine delay is achieved through cascaded absolute delay element called IODELAYE1 in FPGA. Besides, the DPDTS, with the ability of automatic clock switch, can protect the controlled laser system. Experiment result shows that, for this designed DPDTS, the accuracy is approximate 78 ps, the time jitter is 55 ps, and the delay range is from 0 to 999 us with delay step of 78 ps.
A clock synchronization and trigger distribution scheme for China Spallation Neutron Source

J. Li,P. Cao,Y. Wang,W. Wang

DOI: https://doi.org/10.1088/1748-0221/19/06/p06039

2024-06-27

Journal of Instrumentation

Abstract:China Spallation Neutron Source (CSNS) is a complex system engineering composed of particle accelerators, a target station, and neutron spectrometers with various equipment types and distribution. The collaborative operation of the equipment requires accurate clock synchronization and trigger distribution. Currently, to meet the requirements of different system devices, clock synchronization and trigger distribution in CSNS are implemented based on different methods, resulting in complex clock and trigger networks, demanding upgrades, and a lack of unified timestamps. This paper proposes a clock synchronization and trigger distribution scheme based on the field-programmable gate array (FPGA) and single-mode dual-core fiber link. The decoupling of clock phase synchronization and time base synchronization improves the frequency of phase compensation. Benefiting from the phase interpolator (PI) in the FPGA transceivers, high-precision phase compensation and phase deterministic control are realized, achieving picoseconds synchronization precision and stability in the four-level network. Based on the custom lightweight link layer protocol, by optimizing the routing method of data frames and adopting priority control, the transmission of multiple data is realized, and the hardware delay of the critical data, such as interlock, is guaranteed to be less than 1.5 μs in the four-level system. The scheme provides a general precise clock synchronization and distributed trigger method for CSNS devices, simplifies the system complexity, and is conducive to the system upgrade in the second stage.

instruments & instrumentation
A 19.6 ps, FPGA-Based TDC With Multiple Channels for Open Source Applications

Matthew W. Fishburn,L. Harmen Menninga,Claudio Favi,Edoardo Charbon,MatthewW. Fishburn

DOI: https://doi.org/10.1109/tns.2013.2241789

IF: 1.703

2013-06-01

IEEE Transactions on Nuclear Science

Abstract:This work presents a multi-channel, time-to-digital converter (TDC) based on a field-programmable gate array (FPGA). A thorough characterization of the TDC, based on a Xilinx Virtex-6 FPGA, is presented and several performance parameters are described, including distortions due to the FPGA architecture, temperature effects, intra-chip position variation, and chip-to-chip variation. An optimized TDC exhibits 10 ps LSB duration, an integral non-linearity range of 3.86 LSB, and an input range longer than 100 $\mu$s. Total time uncertainty (single-shot jitter) is measured to be 19.6 ps at a time difference of 40 ns, and less than 400 ps at a time difference larger than 100 $\mu$s.

engineering, electrical & electronic,nuclear science & technology
Development of Sub-100 Femtosecond Timing and Synchronization System.

Zhenyang Lin,Yingchao Du,Jin Yang,Yilun Xu,Lixin Yan,Wenhui Huang,Chuanxiang Tang,Gang Huang,Qiang Du,Lawrence Doolittle,Russell Wilcox,John Byrd

DOI: https://doi.org/10.1063/1.5001768

IF: 1.6

2018-01-01

Review of Scientific Instruments

Abstract:The precise timing and synchronization system is an essential part for the ultra-fast electron and X-ray sources based on the photocathode injector where strict synchronization among RF, laser, and beams are required. In this paper, we present an integrated sub-100 femtosecond timing and synchronization system developed and demonstrated recently in Tsinghua University based on the collaboration with Lawrence Berkeley National Lab. The timing and synchronization system includes the fiber-based CW carrier phase reference distribution system for delivering stabilized RF phase reference to multiple receiver clients, the Low Level RF (LLRF) control system to monitor and generate the phase and amplitude controllable pulse RF signal, and the laser-RF synchronization system for high precision synchronization between optical and RF signals. Each subsystem is characterized by its blocking structure and is also expansible. A novel asymmetric calibration sideband signal method was proposed for eliminating the non-linear distortion in the optical synchronization process. According to offline and online tests, the system can deliver a stable signal to each client and suppress the drift and jitter of the RF signal for the accelerator and the laser oscillator to less than 100 fs RMS (∼0.1° in 2856 MHz frequency). Moreover, a demo system with a LLRF client and a laser-RF synchronization client is deployed and operated successfully at the Tsinghua Thomson scattering X-ray source. The beam-based jitter measurement experiments have been conducted to evaluate the overall performance of the system, and the jitter sources are discussed.
Field-programmable gate array-based residual amplitude modulation suppression and control for compact atomic clocks

Tin Nghia Nguyen,Thomas R. Schibli

DOI: https://doi.org/10.1063/5.0185763

IF: 1.6

2024-02-01

Review of Scientific Instruments

Abstract:We designed a field-programmable gate array (FPGA) fabric to provide phase modulation techniques to lock lasers to optical frequency references. The method incorporates an active residual amplitude modulation (RAM) suppression scheme that relies on complex modulation. All the required servos to construct an optical atomic clock are incorporated into the same low-cost, commercial FPGA chip. We demonstrate a reliable, long-term RAM suppression of 60 dB with the remaining RAM level at −100 dBc and an improved stability of three decades when applied on a two-photon rubidium clock.

instruments & instrumentation,physics, applied
High frequency signal acquisition and control system based on DSP+FPGA

Xiao-qi Liu,Da-zhi Zhang,Ya-dong Yin,YaDong Yin,DaZhi Zhang,XiaoQi Liu

DOI: https://doi.org/10.1117/12.2284317

2017-10-24

Abstract:This paper introduces a design and implementation of high frequency signal acquisition and control system based on DSP + FPGA. The system supports internal/external clock and internal/external trigger sampling. It has a maximum sampling rate of 400MBPS and has a 1.4GHz input bandwidth for the ADC. Data can be collected continuously or periodically in systems and they are stored in DDR2. At the same time, the system also supports real-time acquisition, the collected data after digital frequency conversion and Cascaded Integrator-Comb (CIC) filtering, which then be sent to the CPCI bus through the high-speed DSP, can be assigned to the fiber board for subsequent processing. The system integrates signal acquisition and pre-processing functions, which uses high-speed A/D, high-speed DSP and FPGA mixed technology and has a wide range of uses in data acquisition and recording. In the signal processing, the system can be seamlessly connected to the dedicated processor board. The system has the advantages of multi-selectivity, good scalability and so on, which satisfies the different requirements of different signals in different projects.
Digital Signal Acquisition System for Complex Nuclear Reaction Experiments

Wei-Liang Pu,Yan-Lin Ye,Jian-Ling Lou,Jia-Hao Chen

DOI: https://doi.org/10.1007/s41365-024-01366-9

2024-01-01

Nuclear Science and Techniques

Abstract:A digital data-acquisition system based on XIA LLC products was used in a complex nuclear reaction experiment using radioactive ion beams. A flexible trigger system based on a field-programmable gate array (FPGA) parametrization was developed to adapt to different experimental sizes. A user-friendly interface was implemented, which allows converting script language expressions into FPGA internal control parameters. The proposed digital system can be combined with a conventional analog data acquisition system to provide more flexibility. The performance of the combined system was verified using experimental data.
Implementation of FPGA based real-time digital DAQ for high resolution, and high count rate nuclear spectroscopy application

T. Samanta,S. Pal,Ram Kumar Paul,A. Banerjee,P. Dhara,A. Das,K. Banerjee

DOI: https://doi.org/10.1088/1748-0221/18/07/P07042

2023-07-01

Journal of Instrumentation

Abstract:This paper investigates a digital system for real-time nuclear data (pulse) analysis based on a field programmable gate array and a computer-based data acquisition software for high count rate and high-resolution spectroscopy applications. A novel FPGA-based design is proposed with enhanced universality for real-time energy spectroscopy applications encompassing gamma and charged particles in noisy environments. This design implements an adaptive digital pre-filter for noise reduction without distorting the preamplifier pulse shape for improvement in energy resolution. This adaptive approach can be used for a wide range of input pulses with varying rise and fall times without deteriorating the signal-to-noise ratio. The design incorporates a digital trapezoidal filter with a triggerless peak detection algorithm for improvement in energy resolution. A high-speed dual clock first-in-first-out memory is implemented for handling high data rates. The real-time analysis of the FPGA internal signals and nuclear spectroscopy experiments with high count rate have been carried out with random nuclear pulses using an emulator. The results have been compared with conventional VERSA-Module Euro data acquisition system and CR_RC based digital pulse processing approaches.

Engineering,Computer Science,Physics
FPGA based High Speed Data Acquisition System for High Energy Physics Application

Swagata Mandal,Suman Sau,Amlan Chakrabarti,Subhasis Chattopadhyay

DOI: https://doi.org/10.48550/arXiv.1503.08819

2015-03-30

Abstract:In high energy physics experiments (HEP), high speed and fault resilient data communication is needed between detectors/sensors and the host PC. Transient faults can occur in the communication hardware due to various external effects like presence of charged particles, noise in the environment or radiation effects in HEP experiments and that leads to single/multiple bit error. In order to keep the communication system functional in such a radiation environment where direct intervention of human is not possible, a high speed data acquisition (DAQ) architecture is necessary which supports error recovery. This design presents an efficient implementation of field programmable gate array (FPGA) based high speed DAQ system with optical communication link supported by multi-bit error correcting model. The design has been implemented on Xilinx Kintex-7 board and is tested for board to board communication as well as for PC communication using PCI (Peripheral Component Interconnect express). Data communication speed up to 4.8 Gbps has been achieved in board to board and board to PC communication and estimation of resource utilization and critical path delay are also measured.

Instrumentation and Detectors,Hardware Architecture,High Energy Physics - Experiment
A 3.8 ps RMS time synchronization implemented in a 20 nm FPGA

Hong-Bo Xie,Yang Li,Qi Shen,Sheng-Kai Liao,Cheng-Zhi Peng

2018-01-01

Abstract:A 3.8ps root mean square (RMS) time synchronization implemented in a 20nm fabrication process ultrascale kintex Field Programmable Gate Array (FPGA) is presented. The multichannel high-speed serial transceivers (e.g. GTH) play a key role in a wide range of applications, such as the optical source for quantum key distribution systems. However, owing to the independent clock dividers existed in each transceiver, the random skew would appear among the multiple channels every time the system powers up or resets. A self-phase alignment method provided by Xilinx Corporation could reach a precision with 22 ps RMS and 100 ps maximum variation, which is far from meeting the demand of applications with rate up to 2.5 Gbps. To implement a high-precision intrachannel time synchronization, a protocol combined of a high-precision time-to-digital converter (TDC) and a tunable phase interpolator (PI) is presented. The TDC based on the carry8 primitive is applied to measure the intrachannel skew with 40.7ps bin size. The embedded tunable PI in each GTH channel has a theoretical step size of 3.125 ps. By tuning the PI in the minimal step size, the final intrachannel time synchronization reaches a 3.8 ps RMS precision and maximal variation 20 ps, much better than the self-phase alignment method. Besides, a desirable time offset of every channel can be implemented with a closed-loop control.
LLRF control system for PKU DC-SC photocathode injector

Hongxia Zhang,J. K. Hao,Lin Lin,Kexin Liu,Fang Wang,B. C. Zhang

2011-01-01

Abstract:A digital low level RF control system based on Field-Programmable Gate Array (FPGA) with high precision is being developed for the stable operation of upgraded Direct Current-Superconductive (DC-SC) photocathode injector at Peking University. The design of this Low level radio frequency (LLRF) control system is described, including both hardware and internal algorithm. The system is designed to achieve the requirement of ±0.1% for amplitude stability and ±0.1o for phase stability. Copyright © 2011 by IPAC'11/EPS-AG.
Design of Fast Machine Protection System for the C-ADS Injection I

Fang Liu,Guanghua Gong,Jun Hu,X. S. Jiang,Qiang Ye

DOI: https://doi.org/10.18429/jacow-icalepcs2015-mopgf134

2015-01-01

Abstract:In this paper a new fast machine protection system is proposed. This system is designed for the injection Ι of CADS which fault reaction time requires less than 20 us, and the one minute down time requires less than 7 times in a whole year. The system consist of one highly reliable control network based on a control board and some front IO sub-boards, and one nanosecond precision timing system using white rabbit protocol. The control board and front IO sub-board are redundant separately. The structure of the communication network is a combination structure of star and tree types which using the 2.5 GHz optical fiber links the all nodes. This paper pioneered the use of nanosecond timing system based on the white rabbit protocol to determine the time and sequence of each system failure. Another advantage of the design is that it uses standard FMC and an easy extension structure which made the design is easy to use in a large accelerator. INTRODUCTION The injection Ι of ADS (Accelerator Driven Sub-critical System) is being constructed in institute of high energy physics, China [1]. How to ensure the safe and stable operation of the injection, the fast protection system has played a crucial role. The protection system needs to make a quick decision on the current failure. When a general failure, the system needs to quickly adjust the system without stopping and set the working state to the normal mode. When a serious fault, it is necessary to quickly send out a signal and shutdown the whole system. The system also cans storage the statement before and after the fault. Through the storage of information the staff can quickly rule out the reason of occurrence failure [2]. FAST MACHINE PROTECTION SYSTEM FRAMEWORK ADS fast protection system is composed of main control board, some front IO sub-boards, supervisory computer and one nanosecond precision timing system. The system framework is shown in Fig. 1. Front IO sub-board monitors the 24V or 5V switch signal from the LLRF, PS, Vacuum, RFQ and other critical points. When the monitored points occur error, it sends the error signal to the main control board through optical fiber. The signal contains the time information that is labelled by the White Rabbit system. The main control board analyses and judgments the error through the stored fault tree. Then, it issued the processing results to the front IO sub-boards. Meanwhile, the main control board WR SWITCH GPS/ RUBIDIUM OSCILLATOR/ SYSTEM REFERENCE CLOCK
Hardware Acceleration of Digital Pulse Shape Analysis Using FPGAs

César González,Mariano Ruiz,Antonio Carpeño,Alejandro Piñas,Daniel Cano-Ott,Julio Plaza,Trino Martinez,David Villamarin

DOI: https://doi.org/10.3390/s24092724

IF: 3.9

2024-04-26

Sensors

Abstract:The BC501A sensor is a liquid scintillator frequently used in nuclear physics for detecting fast neutrons. This paper describes a hardware implementation of digital pulse shape analysis (DPSA) for real-time analysis. DPSA is an algorithm that extracts the physically relevant parameters from the detected BC501A signals. The hardware solution is implemented in a MicroTCA system that provides the physical, mechanical, electrical, and cooling support for an AMC board (NAMC-ZYNQ-FMC) with a Xilinx ZYNQ Ultrascale-MP SoC. The Xilinx FPGA programmable logic implements a JESD204B interface to high-speed ADCs. The physical and datalink JESD204B layers are implemented using hardware description language (HDL), while the Xilinx high-level synthesis language (HLS) is used for the transport and application layers. The DPSA algorithm is a JESD204B application layer that includes a FIR filter and a constant fraction discriminator (CFD) function, a baseline calculation function, a peak detection function, and an energy calculation function. This architecture achieves an analysis mean time of less than 100 μs per signal with an FPGA resource utilization of about 50% of its most used resources. This paper presents a high-performance DPSA embedded system that interfaces with a 1 GS/s ADC and performs accurate calculations with relatively low latency.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Low-cost FPGA-based multi-channel TDC with high resolution and density for time-of-flight detectors

Xinpeng Wang,Haibo Yang,Xiaolin Xia,Chaojie Zou,Yangzhou Su,Wenchao Sun,Shikai Wang,Yun Zhao,Chengxin Zhao

DOI: https://doi.org/10.1088/1748-0221/19/11/c11008

2024-11-24

Journal of Instrumentation

Abstract:The Time-to-Digital Converter (TDC) is widely used for precise time interval measurements and play a critical role in Time-of-Flight (ToF) applications. In this paper, we present the design of a 64-channel leading-edge and trailing-edge TDC based on a Field-Programmable Gate Array (FPGA). This TDC is implemented on a Xilinx Kintex-7 XC7K410T-2FFG900I FPGA and consists of modules including a coarse counter, pulse generator, tapped delay line, decomposition encoder, and calibrator. To better evaluate its performance, we designed a multi-channel hardware verification board. According to laboratory test results, the timing precision has a root mean square (RMS) value of 6.69 ps, and a least significant bit (LSB) of 2.99 ps. The experimental results confirm that our TDC design achieves excellent timing precision.

instruments & instrumentation
An FPGA-Based Hardware Platform for the Control of Spin-Based Quantum Systems

Xi Qin,Wenzhe Zhang,Lin Wang,Yuxi Zhao,Yu Tong,Xing Rong,Jiangfeng Du

DOI: https://doi.org/10.1109/tim.2019.2910921

IF: 5.6

2019-01-01

IEEE Transactions on Instrumentation and Measurement

Abstract:This paper reports the development of a highly efficient, flexible hardware platform, which is suitable for the control of spin-based quantum systems including quantum computation and quantum metrology. A two-channel arbitrary waveform generator (AWG), an eight-channel pulse/sequence generator, a two-channel analog-to-digital converter (ADC), and a two-channel high-speed time-to-digital converter (TDC) are fully integrated on a printed circuit board (PCB). The AWG has a 1-GSa/s sampling rate and a 16-bit amplitude resolution. The pulse/sequence generator can continuously output pulse/sequence signals with a 50-ps time resolution and a dynamic range from 5 ns to 2 s. The ADC provides a 1-GSa/s sampling rate and a 12-bit amplitude resolution for analog signal acquisition. The TDC provides a 6-ps time resolution and a maximum sampling frequency of 125 MHz. All these modules are realized utilizing a field-programmable gate array (FPGA). Customized data calculation modules are also implemented with the FPGA logic. The hardware was tested and implemented in a pulsed electron spin resonance (ESR) spectrometer and an optically detected magnetic resonance (ODMR) spectrometer.
Design of a Low Level Radio Frequency Control System for the Direct Current-Superconductive Photocathode Injector at Peking University

Zhang He,Wang Fang,Zhang Bao-Cheng,Lin,Hao Jian-Kui,Liu Ke-Xin

DOI: https://doi.org/10.1088/1674-1137/35/10/013

2011-01-01

Abstract:A digital low level radio frequency （LLRF） control system based on a high precision fieldprogrammable gate array （FPGA） is being developed for the stable operation of the upgraded direct currentsuperconductive （DC-SC） photocathode injector at Peking University.The design of this LLRF control system is described,including both the hardware and the internal algorithm.Analysis of disturbances shows that the system can achieve the requirement of ±0.1% for amplitude stability and ±0.1 for phase stability.Through experiments,preliminary results are presented in the paper.
Long-term follow-up of tandem autologous stem-cell transplantation in multiple myeloma.

J. Regelink,Cinthy H M van Roessel,K. V. van Galen,G. Ossenkoppele,P. Huijgens,S. Zweegman

DOI: https://doi.org/10.1200/JCO.2010.31.5515

IF: 45.3

2010-12-10

Journal of Clinical Oncology

Abstract:
An FPGA-Based TDC for Free Space Quantum Key Distribution

Qi Shen,Shengkai Liao,Shubin Liu,Jinhong Wang,Weiyue Liu,Chengzhi Peng,Qi An

DOI: https://doi.org/10.1109/tns.2013.2280169

IF: 1.703

2013-01-01

IEEE Transactions on Nuclear Science

Abstract:Quantum key distribution (QKD) is the most matured application of quantum communication. The time synchronization and system timing jitter are essential to a practical QKD experiment, which can directly influence the quantum bit error rate (QBER) and the final key rate. High precision time-to-digital converters (TDCs) can effectively reduce the system timing jitter, resulting in lower QBER and higher key rate. Here, we introduce a TDC based on a field programmable gate array (FPGA). Its high resolution (LSB) of 50 ps with precision (RMS) less than 50 ps, low dead time and large dynamic range can well meet the requirement of the QKD experiment. A free space QKD system setup using the FPGA-based TDC has been assembled. The timing precision of the synchronous light and the system timing jitter were determined. The results demonstrate that the FPGA-based TDC could be successfully applied in the QKD experiment.

Control of an epidemic spread of a multi-resistant strain ofAcinetobacter calcoaceticus in a hospital

An FPGA-based Timing and Control System for the Dynamic Compression Sector

Digital phase control system for ssrf linac

A Multi-Channel Digital Programable Delay Trigger System with High Accuracy and Wide Range

A clock synchronization and trigger distribution scheme for China Spallation Neutron Source

A 19.6 ps, FPGA-Based TDC With Multiple Channels for Open Source Applications

Development of Sub-100 Femtosecond Timing and Synchronization System.

Field-programmable gate array-based residual amplitude modulation suppression and control for compact atomic clocks

High frequency signal acquisition and control system based on DSP+FPGA

Digital Signal Acquisition System for Complex Nuclear Reaction Experiments

Implementation of FPGA based real-time digital DAQ for high resolution, and high count rate nuclear spectroscopy application

FPGA based High Speed Data Acquisition System for High Energy Physics Application

A 3.8 ps RMS time synchronization implemented in a 20 nm FPGA

LLRF control system for PKU DC-SC photocathode injector

Design of Fast Machine Protection System for the C-ADS Injection I

Hardware Acceleration of Digital Pulse Shape Analysis Using FPGAs

Low-cost FPGA-based multi-channel TDC with high resolution and density for time-of-flight detectors

An FPGA-Based Hardware Platform for the Control of Spin-Based Quantum Systems

Design of a Low Level Radio Frequency Control System for the Direct Current-Superconductive Photocathode Injector at Peking University

Long-term follow-up of tandem autologous stem-cell transplantation in multiple myeloma.

An FPGA-Based TDC for Free Space Quantum Key Distribution