Mid-infrared Imaging Observation of Gas-phase Samples Using Transparent Ceramics Optics

H. Murakami,N. Tanaka,S. Ono,N. Sarukura

DOI: https://doi.org/10.1109/CLEOPR.2007.4391096

2007-08-26

Abstract:Mid-infrared imaging observation of gas samples using new transparent ceramic optical material, LUMICERA, was demonstrated. With a high transmission from the visible to the mid-infrared, it promises to be a flexible mid-infrared optical material.

What problem does this paper attempt to address?

Engineering Materials for Mid-Infrared Optical Sensor Applications

K. A. Richardson,J. D. Musgraves,P. Wachtel,S. Novak,S. Danto,A. Agarwal,V. Singh,P-T Lin,L. C. Kimerling,J. Hu,Z. Yi,H. Lin,J. Giammarco,A. P. Soliani,I. Luzinov,J. Hensley

DOI: https://doi.org/10.1051/matecconf/20130802002

2013-01-01

MATEC Web of Conferences

Abstract:Planar optical structures based on functionalized chalcogenide glasses provide a superb device platform for chemical and biological sensing applications. Chalcogenide glasses have demonstrated promise as materials for infrared sensing as they exhibit transparency over a large range of infrared wavelengths and tunable optical properties through doping and/or compositional tailoring. Waveguides, resonators and other components processed on-chip (silicon, Si) can be realized such that the strong enhancement in the electromagnetic field confined within a high index contrast resonator, leads to highly sensitive photon-matter interactions in a small footprint. In this paper we discuss the development of highly sensitive chalcogenide glass based microdisk resonator sensors that measure resonant peak shifts caused by refractive index change upon exposure to a chemical analyte. The specificity of the microdisk resonator sensors is enhanced by applying specialized polymer films and nanofoams that respond in a predictable fashion when exposed to a chemical analyte of interest. Discussed are key material science challenges needed to enable highly sensitive and specific sensors based on such complex multi-material assemblies and the fabrication issues that ultimately define resulting optical performance.
Cavity-enhanced Mid-Infrared On-Chip Chemical Sensing Using High-Q Chalcogenide Glass Resonators

Hongtao Lin,Yesh Chillakuru,Kati McLaughlin,Lan Li,Yi Zou,Fei Deng,Chaoying Ni,Sylvain Danto,J. David Musgraves,Kathleen Richardson,Juejun Hu

DOI: https://doi.org/10.1109/icsens.2013.6688278

2013-01-01

Abstract:We experimentally demonstrated for the first time on-chip cavity-enhanced mid-infrared spectroscopic sensing of chemical molecules, performed near 5.2 μm wavelength using Ge23Sb7S70 resonators monolithically fabricated on CaF2 substrates.
Mid-infrared all-fiber light-induced thermoelastic spectroscopy sensor based on hollow-core anti-resonant fiber

Weipeng Chen,Shunda Qiao,Ying He,Jie Zhu,Kang Wang,Lei Qi,Sheng Zhou,Limin Xiao,Yufei Ma

DOI: https://doi.org/10.1016/j.pacs.2024.100594

IF: 9.656

2024-02-12

Photoacoustics

Abstract:In this article, a mid-infrared all-fiber light-induced thermoelastic spectroscopy (LITES) sensor based on a hollow-core anti-resonant fiber (HC-ARF) was reported for the first time. The HC-ARF was applied as a light transmission medium and gas chamber. The constructed all-fiber structure has merits of low loss, easy optical alignment, good system stability, reduced sensor size and cost. The mid-infrared transmission structure can be utilized to target the strongest gas absorption lines. The reversely-tapered SM1950 fiber and the HC-ARF were spatially butt-coupled with a V-shaped groove between the two fibers to facilitate gas entry. Carbon monoxide (CO) with an absorption line at 4291.50 cm -1 (2.33 μm) was chosen as the target gas to verify the sensing performance. The experimental results showed that the all-fiber LITES sensor based on HC-ARF had an excellent linear response to CO concentration. Allan deviation analysis indicated that the system had excellent long-term stability. A minimum detection limit (MDL) of 3.85 ppm can be obtained when the average time was 100 s.

engineering, biomedical,radiology, nuclear medicine & medical imaging,instruments & instrumentation
High-resolution mid-infrared image transport by a chalcogenide multi-core fiber

Asuka Nakatani,Morio Matsumoto,Goichi Sakai,Takenobu Suzuki,Yasutake Ohishi

DOI: https://doi.org/10.35848/1347-4065/ad82c3

IF: 1.5

2024-10-22

Japanese Journal of Applied Physics

Abstract:We have successfully demonstrated high-resolution mid-infrared image transport by a multi-core fiber made of chalcogenide glasses. The fiber cores are arranged on a triangular lattice and adjacent cores have different core diameters to reduce cross-talk between them. We tested the resolution of the fiber using different fineness patterns and found that it can resolve better than 25 lp/mmat a wavelength of 9.3 μm. This demonstrates the potential of the fiber for high-resolution thermal imaging inside the human body.

physics, applied
Mid-infrared supermirrors with finesse exceeding 400 000

G.-W. Truong,L. W. Perner,D. M. Bailey,G. Winkler,S. B. Cataño-Lopez,V. J. Wittwer,T. Sudmeyer,C. Nguyen,D. Follman,A. J. Fleisher,O. H. Heckl,G. D. Cole

DOI: https://doi.org/10.1038/s41467-023-43367-z

2023-08-01

Abstract:For trace gas sensing and precision spectroscopy, optical cavities incorporating low-loss mirrors are indispensable for path length and optical intensity enhancement. Optical interference coatings in the visible and near-infrared (NIR) spectral regions have achieved total optical losses below 2 parts per million (ppm), enabling a cavity finesse in excess of 1 million. However, such advancements have been lacking in the mid-infrared (MIR), despite substantial scientific interest. Here, we demonstrate a significant breakthrough in high-performance MIR mirrors, reporting substrate-transferred single-crystal interference coatings capable of cavity finesse values from 200 000 to 400 000 near 4.5 um, with excess optical losses (scatter and absorption) below 5 ppm. In a first proof-of-concept demonstration, we achieve the lowest noise-equivalent absorption in a linear cavity ring-down spectrometer normalized by cavity length. This substantial improvement in performance will unlock a rich variety of MIR applications for atmospheric transport and environmental sciences, detection of fugitive emissions, process gas monitoring, breath-gas analysis, and verification of biogenic fuels and plastics.

Optics
UV-curable thiol-ene system for broadband infrared transparent objects

Piaoran Ye,Zhihan Hong,Douglas A Loy,Rongguang Liang

DOI: https://doi.org/10.1038/s41467-023-44273-0

2023-12-16

Abstract:Conventional infrared transparent materials, including inorganic ceramic, glass, and sulfur-rich organic materials, are usually processed through thermal or mechanical progress. Here, we report a photo-curable liquid material based on a specially designed thiol-ene strategy, where the multithiols and divinyl oligomers were designed to contain only C, H, and S atoms. This approach ensures transparency in a wide range spectrum from visible light to mid-wave infrared (MWIR), and to long-wave infrared (LWIR). The refractive index, thermal properties, and mechanical properties of samples prepared by this thiol-ene resin were characterized. Objects transparent to LWIR and MWIR were fabricated by molding and two-photon 3D printing techniques. We demonstrated the potential of our material in a range of applications, including the fabrication of IR optics with high imaging resolution and the construction of micro-reactors for temperature monitoring. This UV-curable thiol-ene system provides a fast and convenient alternative for the fabrication of thin IR transparent objects.
Mid-infrared wide-field nanoscopy

Miu Tamamitsu,Keiichiro Toda,Venkata Ramaiah Badarla,Hiroyuki Shimada,Kuniaki Konishi,Takuro Ideguchi

2023-06-14

Abstract:Mid-infrared (MIR) spectroscopy is widely recognized as a powerful, non-distractive method for chemical analysis. However, its utility is constrained by a micrometer-scale spatial resolution imposed by the long-wavelength MIR diffraction limit. This limitation has been recently overcome by MIR photothermal (MIP) imaging, which detects photothermal effects induced in the vicinity of MIR absorbers using a visible-light microscope. Despite its promise, the full potential of its spatial resolving power has not been realized. Here, we present an optimal implementation of wide-field MIP imaging to achieve high spatial resolution. This is accomplished by employing single-objective synthetic-aperture quantitative phase imaging (SOSA-QPI) with synchronized sub-nanosecond MIR and visible light sources, effectively suppressing the resolution-degradation effect caused by photothermal heat diffusion. We demonstrate far-field MIR spectroscopic imaging with a spatial resolution limited by the visible diffraction, down to 125 nm, in the MIR region of 3.12-3.85 um (2,600-3,200 cm-1). This technique, through the use of a shorter visible wavelength and/or a higher objective numerical aperture, holds the potential to achieve a spatial resolution of less than 100 nm, thus paving the way for MIR wide-field nanoscopy.

Optics
Mid-infrared spectroscopic thermotransmittance measurements in dielectric materials for thermal imaging

C. Bourges,S. Chevalier,J. Maire,A. Sommier,C. Pradere,S. Dilhaire

DOI: https://doi.org/10.1063/5.0176689

IF: 4

2024-01-01

Applied Physics Letters

Abstract:Thermal considerations affect the performance of most microsystems. Although surface techniques can give information on the thermal properties within the material or about buried heat sources and defects, mapping temperature and thermal properties in three dimension (3D) is critical and has not been addressed yet. Infrared thermography, commonly used for opaque materials, is not adapted to semi-transparent samples such as microfluidic chips or semiconductor materials in the infrared range. This work aims at answering these needs by using the variations of transmittance with temperature to obtain information on the temperature within the thickness of the sample. We use a tunable mid-infrared light source combined with an infrared camera to measure these variations of transmittance in a glass wafer. We couple this technique with a thermal model to extract the thermotransmittance coefficient—the coefficient of temperature variation of the transmittance. We then introduce a semiempirical model based on Lorentz oscillators to estimate the temperature-dependent optical properties of our sample in the mid-IR spectral range. Combined with the measurement, this paper reports the spectroscopic behavior of the thermotransmittance coefficient in the mid-IR range and a way to predict it.

physics, applied
Mid-Infrared Photothermal Gas Sensor Enabled By Core-Cladding Mode Interference in a Hollow-Core Fiber

Mengyuan Hu,Chenyu Yao,Andrea Ventura,Juliano Grigoleto Hayashi,Francesco Poletti,Wei Ren

DOI: https://doi.org/10.1109/jlt.2022.3195214

IF: 4.7

2022-10-04

Journal of Lightwave Technology

Abstract:Mengyuan Hu, Chenyu Yao, Andrea Ventura, Juliano Grigoleto Hayashi, Francesco Poletti, Wei Ren Photothermal spectroscopy provides an attractive way of sensitive gas detection with a large dynamic range. Previous photothermal gas ... [J. Lightwave Technol. 40, 6568-6575 (2022)]

engineering, electrical & electronic,optics,telecommunications
Single-molecule mid-IR detection through vibrationally-assisted luminescence

Rohit Chikkaraddy,Rakesh Arul,Lukas A. Jakob,Jeremy J. Baumberg

DOI: https://doi.org/10.48550/arXiv.2205.07792

2022-05-17

Abstract:Room temperature detection of molecular vibrations in the mid-infrared (MIR, $\lambda$ =3-30$\mu$m) has numerous applications including real-time gas sensing, chemical reactivity, medical imaging, astronomical surveys, and quantum communication [1,2]. However, MIR detection is severely hindered by thermal noise, hence current technologies rely on energy-intensive cooled semiconductor detectors (mercury cadmium telluride, MCT) [3,4,5]. One way to overcome this challenge is to upconvert the low-energy MIR light into high-energy visible wavelengths ($\lambda$ =500-800nm) where detection of single photons is easily achieved using silicon technologies [6,7]. This process suffers from weak cross sections and the mismatch between MIR and visible wavelengths, limiting its efficiency. Here, we exploit molecular emitters possessing both MIR and visible transitions from molecular vibrations and electronic states, coupled through Frank-Condon factors. By assembling molecules into a nanoscale cavity and continuously optically pumping them below the electronic absorption band, we show the transduction of MIR light absorbed by the molecular vibrations. The upconverted signal is observed as enhanced high-energy luminescence. Combining Purcell-enhanced visible luminescence with enhanced rates of vibrational pumping gives transduction efficiencies exceeding 10%. By down-scaling the cavity volume below $1nm^3$, we show MIR detection of single-molecular bonds, inaccessible to any previous detector.

Applied Physics,Mesoscale and Nanoscale Physics,Optics
Transparent Ni2+-Doped Lithium-Alumino-Silicate Glass-Ceramics for Broadband Near-Infrared Light Source

Shifeng Zhou,Gaofeng Feng,Botao Wu,Shiqing Xu,Jianrong Qiu

DOI: https://doi.org/10.1088/0022-3727/40/8/009

2007-01-01

Abstract:Broadband infrared luminescence centred at around 1300 nm with full-width at half maximum of about 342 nm was observed from transparent Ni2+-doped lithium-alumino-silicate glass-ceramics embedded with beta-eucryptite crystallines. The room temperature fluorescent lifetime was 98 mu s. The transparent glass-ceramics may have potential applications in a widely tunable laser and a super-broadband optical amplifier for optical communications.
Ultrabroadband mid-infrared emission and gas sensing of cobalt-doped chalcogenide glass ceramics

Han Liu,Yuan Gao,Yikang Jiang,Xiaosong Lu,Zhijie Yang,Pengfei Wang,Zhiyong Yang

DOI: https://doi.org/10.1364/ol.539889

IF: 3.6

2024-10-08

Optics Letters

Abstract:Han Liu, Yuan Gao, Yikang Jiang, Xiaosong Lu, Zhijie Yang, Pengfei Wang, Zhiyong Yang Mid-infrared (MIR) gain materials are of great significance for the development of MIR tunable fiber lasers. Herein, for the first time, to ... [Opt. Lett. 49, 5807-5810 (2024)]

optics
Tunable Ultraviolet/visible to Near-Infrared Down-Conversion Luminescence in the Er3+, Yb3+ Co-Doped (y0.88la0.09zr0.03)2o3 Transparent Ceramics

Yue Hu,Muhammad Shahid,Wei Pan

DOI: https://doi.org/10.1016/j.optmat.2017.05.030

IF: 3.754

2017-01-01

Optical Materials

Abstract:Herein, we report an efficient ultraviolet/visible to near-infrared (NIR) down-conversion luminescence phenomenon in transparent Er3+, Yb3+ co-doped (Y0.88La0.09Zr0.03)(2)O-3 ceramics. Almost fully densified (Y0.88La0.09Zr0.03)(2)O-3 transparent ceramic has been prepared by vacuum sintering at 1800 degrees C with different contents of Er3+ and Yb3+ elements. The intensity ratio of Yb3+: F-2(5/2) -> F-2(7/2) emission (similar to 1000 nm) to the Er3+: 4I(13/2) -> I-4(15/2) emission (similar to 1550 nm) has been tuned by adjusting the excitation wavelength. Phonon-assist quantum cutting from the (4)G(11/2) level of Er3+ with two energy transfer (ET) processes to Yb3+ has been determined, which enhances the Yb3+ emission around the wavelength of 1000 nm. It is found that when one photon around 379 nm is absorbed, two photons around 1000 nm will be emitted, and hence the quantum efficiency is estimated to be similar to 182% in this transparent ceramics. The mechanism of the visible to near-infrared (NIR) down-conversion luminescence in the Er3+, Yb3+ co-doped (Y0.88La0.09Zr0.03)(2)O-3 ceramics has been discussed. (C) 2017 Elsevier B.V. All rights reserved.
Rapid chemically selective 3D imaging in the mid-infrared with a Si-based camera

Eric O. Potma,David Knez,Yong Chen,Amanda Durkin,Alexander Fast,Mihaela Balu,Brenna Norton-Baker,Tommaso Baldacchini,Rachel Martin,Dmitry A. Fishman

DOI: https://doi.org/10.48550/arXiv.2103.01159

2021-03-02

Abstract:The emerging technique of mid-infrared optical coherence tomography (MIR-OCT) takes advantage of the reduced scattering of MIR light in various materials and devices, enabling tomographic imaging at deeper penetration depths. Because of challenges in MIR detection technology, the image acquisition time is however significantly longer than for tomographic imaging methods in the visible/near-infrared. Here we demonstrate an alternative approach to MIR tomography with high-speed imaging capabilities. Through femtosecond non-degenerate two-photon absorption of MIR light in a conventional Si-based CCD camera, we achieve wide-field, high-definition tomographic imaging with chemical selectivity of structured materials and biological samples in mere seconds.

Optics,Instrumentation and Detectors
Ultraflexible Wireless Imager Integrated with Organic Circuits for Broadband Infrared Thermal Analysis (Adv. Mater. 15/2024)

Rei Kawabata,Kou Li,Teppei Araki,Mihoko Akiyama,Kaho Sugimachi,Nozomi Matsuoka,Norika Takahashi,Daiki Sakai,Yuto Matsuzaki,Ryo Koshimizu,Minami Yamamoto,Leo Takai,Ryoga Odawara,Takaaki Abe,Shintaro Izumi,Naoko Kurihira,Takafumi Uemura,Yukio Kawano,Tsuyoshi Sekitani

DOI: https://doi.org/10.1002/adma.202470114

IF: 29.4

2024-04-13

Advanced Materials

Abstract:Ultraflexible Wireless Imager In article number 2309864, Rei Kawabata, Teppei Araki, Yukio Kawano, Tsuyoshi Sekitani, and co‐workers report an ultrathin imager that expands the possibility of non‐destructive testing methods such as "non‐collecting" liquid quality evaluation and "non‐contact" imaging through wireless communication systems. An active matrix of carbon nanotube photodetectors and organic transistors within the imager demonstrates high sensitivity across a wide infrared range, spanning from near‐infrared to terahertz wavelengths, and is expected to be applied to wearable devices and portable imaging devices.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Design and fabrication of a liquid crystal retarder for the mid- and far-infrared wavelength ranges

Moritsugu Sakamoto,Kuon Kawamura,Masato Suzuki,Kohei Noda,Takeya Unuma,Tomoyuki Sasaki,Nobuhiro Kawatsuki,Hiroshi Ono,masato suzuki

DOI: https://doi.org/10.1364/ome.521677

2024-04-04

Optical Materials Express

Abstract:Moritsugu Sakamoto, Kuon Kawamura, Masato Suzuki, Kohei Noda, Takeya Unuma, Tomoyuki Sasaki, Nobuhiro Kawatsuki, Hiroshi Ono We designed and fabricated a liquid crystal (LC) retarder that operates within mid-infrared (MIR) and far-infrared (FIR) wavelength ... [Opt. Mater. Express 14, 1139-1148 (2024)]

materials science, multidisciplinary,optics
Spatially Resolved Temperature Distribution in a Rare-Earth-Doped Transparent Glass-Ceramic

Ivan Sedmak,Rok Podlipec,Iztok Urbančič,Janez Štrancar,Michel Mortier,Iztok Golobič

DOI: https://doi.org/10.3390/s22051970

IF: 3.9

2022-03-02

Sensors

Abstract:Knowing the temperature distribution within the conducting walls of various multilayer-type materials is crucial for a better understanding of heat-transfer processes. This applies to many engineering fields, good examples being photovoltaics and microelectronics. In this work we present a novel fluorescence technique that makes possible the non-invasive imaging of local temperature distributions within a transparent, temperature-sensitive, co-doped Er:GPF1Yb0.5Er glass-ceramic with micrometer spatial resolution. The thermal imaging was performed with a high-resolution fluorescence microscopy system, measuring different focal planes along the z-axis. This ultimately enabled a precise axial reconstruction of the temperature distribution across a 500-μm-thick glass-ceramic sample. The experimental measurements showed good agreement with computer-modeled heat simulations and suggest that the technique could be adopted for the spatial analyses of local thermal processes within optically transparent materials. For instance, the technique could be used to measure the temperature distribution of intermediate, transparent layers of novel ultra-high-efficiency solar cells at the micron and sub-micron levels.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
How to Realize Ultrahigh Photochromic Performance for Real-Time Optical Recording in Transparent Ceramics

Xiao Wu,Fangyuan Yu,Rui Xiong,Peng Wang,Ping Zhou,Baisheng Sa,Cong Lin,Chunlin Zhao,Min Gao,Qiwei Zhang

DOI: https://doi.org/10.1021/acsami.2c16645

IF: 9.5

2023-03-29

ACS Applied Materials & Interfaces

Abstract:A combination of transparency and photochromic (PC) properties in ferroelectrics has promising application potential in smart windows and optical storage/imaging. Nonetheless, limited by understanding the underlying PC mechanism, a splendid PC performance is rarely achieved in transparent ferroelectrics. Here, a strategy to construct deep-lying traps by ion-doping induced defect engineering in (K(0.5)Na(0.5))NbO(3)-based ferroelectric ceramics is proposed. Based on the improved density...

materials science, multidisciplinary,nanoscience & nanotechnology
Broadband near-field mid-infrared spectroscopy and application to phonon resonances in quartz

Michio Ishikawa,Makoto Katsura,Satoru Nakashima,Yuka Ikemoto,Hidekazu Okamura

DOI: https://doi.org/10.1364/OE.20.011064

2012-05-07

Abstract:Infrared (IR) spectroscopy is a versatile analytical method and nano-scale spatial resolution could be achieved by scattering type near-field optical microscopy (s-SNOM). The spectral bandwidth was, however, limited to approximately 300 cm(-1) with a laser light source. In the present study, the development of a broadband mid-IR near-field spectroscopy with a ceramic light source is demonstrated. A much wider bandwidth (at least 3000 to 1000 cm(-1)) is achieved with a ceramic light source. The experimental data on quartz Si-O phonon resonance bands are well reproduced by theoretical simulations indicating the validity of the present broadband near-field IR spectroscopy.

Mid-infrared Imaging Observation of Gas-phase Samples Using Transparent Ceramics Optics

Engineering Materials for Mid-Infrared Optical Sensor Applications

Cavity-enhanced Mid-Infrared On-Chip Chemical Sensing Using High-Q Chalcogenide Glass Resonators

Mid-infrared all-fiber light-induced thermoelastic spectroscopy sensor based on hollow-core anti-resonant fiber

High-resolution mid-infrared image transport by a chalcogenide multi-core fiber

Mid-infrared supermirrors with finesse exceeding 400 000

UV-curable thiol-ene system for broadband infrared transparent objects

Mid-infrared wide-field nanoscopy

Mid-infrared spectroscopic thermotransmittance measurements in dielectric materials for thermal imaging

Mid-Infrared Photothermal Gas Sensor Enabled By Core-Cladding Mode Interference in a Hollow-Core Fiber

Single-molecule mid-IR detection through vibrationally-assisted luminescence

Transparent Ni2+-Doped Lithium-Alumino-Silicate Glass-Ceramics for Broadband Near-Infrared Light Source

Ultrabroadband mid-infrared emission and gas sensing of cobalt-doped chalcogenide glass ceramics

Tunable Ultraviolet/visible to Near-Infrared Down-Conversion Luminescence in the Er3+, Yb3+ Co-Doped (y0.88la0.09zr0.03)2o3 Transparent Ceramics

Rapid chemically selective 3D imaging in the mid-infrared with a Si-based camera

Ultraflexible Wireless Imager Integrated with Organic Circuits for Broadband Infrared Thermal Analysis (Adv. Mater. 15/2024)

Design and fabrication of a liquid crystal retarder for the mid- and far-infrared wavelength ranges

Spatially Resolved Temperature Distribution in a Rare-Earth-Doped Transparent Glass-Ceramic

How to Realize Ultrahigh Photochromic Performance for Real-Time Optical Recording in Transparent Ceramics

Broadband near-field mid-infrared spectroscopy and application to phonon resonances in quartz