Spontaneous neonatal esophageal perforation.

A. Modi,N. Mathur,Y. Sarin

2000-08-01

Indian Pediatrics

Abstract:

What problem does this paper attempt to address?

Zinc Aluminate-Based Composite Nanoparticles for Microwave Applications.

Srilali Siragam,Raghvendra Sarvjeet Dubey,Lakshman Pappula,Gandla Satheesh Babu

DOI: https://doi.org/10.1021/acsomega.2c01671

IF: 4.1

2022-07-20

ACS Omega

Abstract:This paper reports the sol-gel preparation of ZnAlO (ZA) and ZnAlO-TiO (ZAT) dielectric ceramic nanoparticles for fabricating prototype microstrip patch antennas. The prepared nanoparticles were polycrystalline in nature with their crystallite sizes of 9.4 and 11 nm, along with average grain diameters of 16 and 12 nm corresponding to samples ZA and ZAT. Dielectric properties were investigated using an LCR meter, which endorsed enhanced dielectric permittivity and decreased dielectric loss. Finally, prototype microstrip patch antennas named AZA and AZAT were fabricated using the prepared nanoparticles, and their performances were evaluated. Both antennas exhibited resonant peaks in the frequency range from 6.4 to 6.5 GHz. The antenna AZAT showed a return loss of -37.07 dB with a voltage standing wave ratio (VSWR) of 1.02 compared to the return loss of -19.42 dB, and a VSWR of 1.24 corresponds to AZA. The AZAT antenna's improved return loss can be regarded as the increased dielectric permittivity and reduced tangent loss of the ZAT sample. Furthermore, the ZAT antenna evidenced increased/decreased forwarded/reflected power decreased reflection coefficient and an optimal VSWR value compared to that of the AZA antenna.

chemistry, multidisciplinary
Synthesis and Fabrication of Proto-Type Microstrip Patch antenna by using Microwave Dielectric Ceramic Nanocomposite material for C-band Application

Srilali Siragam

DOI: https://doi.org/10.1016/j.ijleo.2024.171787

IF: 3.1

2024-04-06

Optik

Abstract:The microwave dielectric properties of Zn(1- x )Ti x Al 2 O 4 (ZTA) ceramic nanomaterials were investigated with a focus towards their use as wireless antennas. The ZTA nanoparticles were prepared using the sol-gel technique at 700 °C for one hour. The inclusion of titanium decreased the nanomaterials' crystallite size and surface shape, which influenced their dielectric permittivity (ε r ). Based on the tested material and microwave antenna theory, ZTA was used to fabricate wireless patch antennas, which were then examined using a PNA series network analyzer. The measured results reveal that the return loss and impedance bandwidths of the antenna were -44.83 dB simulated and -34.88 dB measured, and 240 MHz for simulated and 220 MHz for measured, respectively. At 5.1 GHz operating frequency, the Zn 0.94 Ti 0.06 Al 2 O 4 -based patch antenna demonstrated an exceptional combination of return loss (-34.88 dB), compact size (9.3× 6.3 mm 2 ), and broad bandwidth (220 MHz) as well as VSWR˂2. Ultimately, the fabricated antenna showcases a gain of 4.24 decibels and a directivity of 5.97 decibels.

optics
Sol–gel derived ceramic nanoparticles as an alternative material for microstrip patch antenna in WLAN applications

Sekhar Didde,R. S. Dubey

DOI: https://doi.org/10.1038/s41598-024-63454-5

IF: 4.6

2024-06-21

Scientific Reports

Abstract:In the fast-evolving realm of communication technology, microstrip patch antennas (MPAs) are in high demand owing to their compact size, lightweight, inexpensive, ease of integration, and compatibility with modern electronic devices. This research focuses on the synthesis of ZnAl 2 O 4 Ca (ZAC) ceramic nanoparticles using an economical sol–gel method suitable for microstrip patch antenna applications. The structural analysis study of ZAC nanoparticles confirmed the polycrystalline nature with 8.1 nm of crystallite size whereas an investigation of functional groups showed the corresponding vibration modes. Morphological investigation revealed the spherical grains having their mean diameter of 12.32 nm. The dielectric property's examination, revealed the dielectric permittivity of 13, loss tangent of 0.02, and conductivity of 67 μΩ −1 cm −1 . Furthermore, a prototype patch antenna fabricated using ZAC ceramics demonstrated a dual-band performance at frequencies 2.8 GHz and 4.8 GHz, with return losses of − 25.78 dB and − 28.5 dB, respectively. This work suggests the suitability of ZAC ceramic nanoparticles for use in WLAN applications.

multidisciplinary sciences
Experimental Investigation of Calcium-Doped Zinc Aluminate Nanoparticles as a Promising Material for Microwave Applications

Sekhar Didde,Raghvendra Sarvjeet Dubey,Sampad Kumar Panda,Gandla Satheesh Babu

DOI: https://doi.org/10.1021/acsomega.3c03983

IF: 4.1

2023-10-05

ACS Omega

Abstract:Miniaturization of microstrip patch antennas (MPAs) is vital in applications such as wireless networks, mobile devices, global positioning satellites, and upcoming wireless terminals. This miniaturization has led to a demand for new materials with higher permittivity compared to the existing ones. Zinc aluminate (ZnAl2O4) ceramic is an exceptional and versatile material in this context, thanks to its high dielectric permittivity and low tangent loss, making it suitable for microwave applications. This article explores the feasibility of sol-gel-prepared Ca-doped ZnAl2O4 ceramic nanoparticles to be useful in fabricating a MPA. These nanoparticles were examined using X-ray diffraction, which confirmed their polycrystalline structure, and the morphological investigation evidenced the spherical grains having a mean diameter of 16 nm. The dielectric permittivity of the ZnAl2O4Ca nanoparticles is 21.11, with a tangential loss of 0.0247. A prototype MPA made by using Ca-doped ZnAl2O4 nanoparticles showed a return loss of -20.92 dB at a resonance frequency of 6.8 GHz with a bandwidth of 600 MHz. These results indicate that Ca-doped ZnAl2O4 ceramic nanoparticles possess exceptional dielectric characteristics, which make them a promising candidate for MPA applications.
Design of dual-band rectangular strip patch antenna on Bi0.5Na0.5TiO3 substrate

Ritu Roumya Samal,Dibyaranjan Das,Arpita Priyadarsini Dikhsit,Kajal Parashar,S. K. S. Parashar

DOI: https://doi.org/10.1007/s10854-024-12271-7

2024-03-03

Journal of Materials Science Materials in Electronics

Abstract:Recently, ceramic patch antennas have been intensively researched for mobile communication systems. This work shows the unique use of Bi 0.5 Na 0.5 TiO 3 (BNT) ceramic in microstrip patch antenna substrates for 8–12 GHz operation. The synthesized ferroelectric perovskite-based substrate of thickness t = 1.02 mm was utilized to produce the simulated antenna. The relevant electromagnetic parameters of permittivity, permeability, dielectric loss, magnetic loss, and miniaturization factor were studied. Characterization procedures are used to analyze the synthesized sample's crystal structure, local vibration, surface morphology, and elemental analysis. The rectangular-based split ring microstrip patch antenna's reflection loss, return loss, and radiation pattern were calculated using CST Microwave Studio v. 2019. The best yield result of simulation is − 55 dB which corresponds to the fabricated result of about − 25 dB for substrate thickness of t = 1.02 mm. The uniqueness of the synthesized sample has been modified parametrically by modifying its thickness for t = 0.9 mm, t = 1 mm, and t = 1.02 mm among which t = 1.02 mm thickness of the substrate is optimal for optimum results.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
Design and fabrication of a C-band patch antenna using novel low permittivity SrGa2Si2O8 microwave dielectric ceramic

Changzhi Yin,Kang Du,Zhengyu Zou,Xiaoqiang Song,Ying Xiong,Fei Wang,Meng Zhang,Weicheng Lei,Yaodong Liu,Wenzhong Lu,Chunchun Li,Wen Lei

DOI: https://doi.org/10.1016/j.jeurceramsoc.2023.06.027

IF: 5.7

2023-06-01

Journal of the European Ceramic Society

Abstract:A novel microwave dielectric ceramic of SrGa2Si2O8 was synthesized using the traditional solid-state method. Its phase composition, microstructure, and microwave dielectric properties were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy, and network analyzer. XRD results indicated that the space group of the ceramic transformed from I 2 /c to P 21 /a at 700 °C. A combination of good microwave dielectric properties was obtained at 1260 °C with ε r = 6.3, Q×f= 96,600 GHz and τ f = −45.2 ppm/°C at 16.5 GHz. The negative τ f can be tuned to near zero by adding 15 mol% CaTiO3. The densification temperature can be reduced to 940 °C by adding 4 wt% LiF. Moreover, the SrGa2Si2O8 ceramic had good chemical compatibility with the Ag electrode. A patch antenna was designed using the 0.85SrGa2Si2O8 + 0.15CaTiO3 + 4 wt% LiF ceramic. The antenna had a high radiation efficiency of 99.2 % and a gain of 2.988 dBi at the center frequency of 4.261 GHz. All results indicated that the SrGa2Si2O8 ceramic has promising potential for applications in 5 G wireless communication technology.

materials science, ceramics
Investigation of BaTiO$_3$-NiO composite as compact Dielectric Resonator Antenna

Prithwiraj Ganguly,Vince Kumar,P. Maneesha,Saptarshi Ghosh,Somaditya Sen

2024-10-14

Abstract:A compact dielectric resonator antenna has been fabricated on a microstrip transmission line for the purpose of C-band wireless communication using a ceramic material made out of a sintered mixture of BTO and NiO. The antenna parameters are optimized using Ansys HFSS software and verified experimentally. Ni replaces both Ba at A site and Ti at B site. Such a solid solution has a limit depending on the amount of NiO provided during sintering. A complete study of the structural changes and the dielectric constant enables the correlation with the resonating property. All the samples retain the ferroelectric tetragonal P4mm phase with a nominal decrease in the c/a ratio. NiO incorporation in BTO decreases the sintering temperature and shows two types of morphology associated with BTO-like and NiO-like phases. It induces prominent reduction in the permittivity and loss tangent (<0.01) in the range 100Hz to 1MHz. These properties make these samples suitable for DRA application in the C-Band range [4-8 GHz]. Experimental and theoretical assessment using HFSS software yields a C-band signal at ~7.27 GHz.

Applied Physics,Materials Science
Cold sintered CaTiO3-K2MoO4 microwave dielectric ceramics for integrated microstrip patch antennas

Dawei Wang,Shiyu Zhang,Ge Wang,Yiannis Vardaxoglou,Will Whittow,Darren Cadman,Di Zhou,Kaixin Song,Ian M. Reaney

DOI: https://doi.org/10.1016/j.apmt.2019.100519

IF: 8.663

2020-03-01

Applied Materials Today

Abstract:CaTiO3-K2MoO4 (CTO-KMO) dielectric composites were successfully cold-sintered at 150 °C for 30 min with a uniaxial pressure of 200 MPa. X-ray diffraction, Raman spectroscopy, back-scattered SEM and energy dispersive x-ray mapping confirmed the coexistence of CTO and KMO with no evidence of interdiffusion and parasitic phases either between the two ceramic end-members or with Ag internal electrodes. As KMO concentration increased, the temperature coefficient of resonant frequency (TCF) and relative pemittivity (εr ) decreased but the microwave quality factor (Q × f) increased. A near-zero TCF composition was obtained for CTO-0.92KMO composites which exhibited εr ∼ 8.5 and Q × f ∼ 11,000 GHz. A microstrip patch antenna was designed and fabricated using cold sintered CTO-0.92KMO as a substrate (40×40×1.4 mm), which gave a s11 of −14.2 dB and a radiation efficiency of 62.0 % at 2.51 GHz.

materials science, multidisciplinary
Co-substituted CuO–ZrO2–Nb2O5 composite ceramics with low-temperature sintering and low-loss for high-performance patch antenna

Fuyu Li,Xinyan Liu,Yuanxun Li,Tingting Tang,Yulong Liao,Yongcheng Lu,Rui Peng,Qin Zhang,Xiaohui Wu,Qiye Wen

DOI: https://doi.org/10.1016/j.ceramint.2022.03.122

IF: 5.532

2022-03-01

Ceramics International

Abstract:In the field of microwave dielectric ceramics for patch antennas, it has always been a thorny issue to simultaneously satisfy high dielectric constant, low sintering temperature and low dielectric loss. Here, a CCZN (x = 0.04) composite ceramic with excellent microwave dielectric properties was developed. It can be found that an appropriate amount of Co2+ substitution can enhance the compactness, increase the dielectric constant (ε r ), reduce the dielectric loss (tanδ) and enhance the temperature coefficient (τ f ). The composite ceramic with excellent dielectric properties (ε r = 22.6, Q × f = 37,624 GHz, τ f = −64.9 ppm/°C) shows good sintering compatibility with Ag. Based on this composite ceramic, a high-performance patch antenna was designed for Beidou satellite navigation system (BDS). It presents a small size of 30 × 30*3.8 mm3 and excellent radiation performance (return loss = −32.9 dB, VSWR = 1.047, impedance bandwidth = 60.6 MHz, radiation efficiency = 94.6% and realized gain = 7.704 dB). This work promotes the application of microwave dielectric ceramics in the field of patch antennas.

materials science, ceramics
A novel Y3ZnAl3SiO12 microwave dielectric ceramic for microwave communication application as substrates

Haiqing Yin,Kaixin Song,Jinsheng Wei,Junming Xu,Jun Wu,Huifang Gao,Weitao Su,Huixing Lin

DOI: https://doi.org/10.1007/s10854-017-7573-3

2017-07-27

Abstract:Novel microwave dielectric ceramic Y3ZnAl3SiO12 were synthesized by solid-state route. The crystal structure of synthesized samples was characterized by X-ray diffraction and refined with Rietveld method. Microstructure and microwave dielectric properties of Y3ZnAl3SiO12 ceramics were investigated using Scanning Electron Microscopy and Hakki–Coleman method. X-ray data display that major phase of Y3ZnAl3SiO12 is isostructural to Y3Al5O12 with a cubic garnet structure and space group of Ia-3d, which is composed of (Al/Si)O4 tetrahedron, (Zn/Al)O6 octahedron and YO8 dodecahedron, besides minor Y2SiO5 secondary phase. The distribution of grain sizes is closer to Gauss distribution. Bulk density of samples has a similar variation curve with Q*f of samples. Y3ZnAl3SiO12 ceramics exhibit excellent microwave dielectric properties: εr = 10.2, Q*f = 37938.2 (@9.47 GHz), τf = −31.7 ppm/°C at sintering temperature of 1500 °C. Our results indicate Y3ZnAl3SiO12 could be a potential material for millimeter wave communication systems as microwave substrates.
Crystal structure, microwave dielectric properties, and dielectric resonant antenna studies of novel low-permittivity CoAl2O4 spinel ceramics

Yi Ding,Cheng Chao Hu,Wei Qin Sheng,Kai Xin Song,Bing Liu

DOI: https://doi.org/10.1007/s10854-021-06760-2

Abstract:CoAl2O4 spinel ceramics were prepared via a standard solid-state reaction method, and their crystal structure, microwave dielectric properties, and dielectric resonant antenna applications were systematically investigated in this study. X-Ray diffraction patterns and Raman spectra confirmed that CoAl2O4 belongs to the Fd-3 m space group with cubic crystal symmetry. εr and Qf values increased with the increasing sintering temperature, where an ever-improving microstructure was also observed from the scanning electron micrographs. The optimal microwave dielectric properties were achieved as follows: εr = 9.34, Qf = 30,500 GHz, and τf = -54 ppm/°C. Moreover, a dielectric resonant antenna was designed and simulated to demonstrate the application prospects of CoAl2O4 ceramics towards microwave antennas. The CoAl2O4-based antenna resonating at 14.33 GHz exhibited a high return loss of -40.9 dB, a wide impedance bandwidth of 940 MHz, and an exceptionally high total efficiency of 96.6%. The remarkable antenna performances suggested that CoAl2O4 ceramics were promising candidates for wireless communication devices operating at the Ku-band, provided τf can be further tuned toward zero.
An investigation of microwave dielectric properties of BaZr0.25Ti0.75O3 and performance of DRA for 5G application

S. Mohapatra,T. Badapanda,Satya N. Tripathy

DOI: https://doi.org/10.1007/s10854-024-11937-6

2024-01-19

Journal of Materials Science Materials in Electronics

Abstract:BaZr 0.25 Ti 0.75 O 3 ceramic's structural, microstructural, and dielectric performances in the microwave region are illustrated in the current work for its prospective use in dielectric resonator antennas at the 5G frequency. Making the BaZr 0.25 Ti 0.75 O 3 composition involved using the standard solid-state method. The phase was discovered by the X-ray diffraction process, proving a cubic symmetry to exist in the composition. The Rietveld refinement method was used to obtain the structural parameters. The BaZr 0.25 Ti 0.75 O 3 ceramic's microstructural shape shows a clearly defined, dense grain. Measurements of the prepared sample's microwave dielectric properties were made across the frequency range of 1 to 10 GHz. Around 2–5 GHz, it is discovered that the relative permittivity and dielectric loss are mainly stable and change with frequency. The quality factor (Q × f) and temperature coefficient of resonant frequency (τ f ), which are the dielectric factors in the microwave area, were computed using the conventional formula. The temperature-dependent dielectric properties have been used to compute the permittivity's temperature coefficient. HFSS software has been used to investigate the simulated performance of dielectric resonator antennas (DRA)-based on BaZr 0.25 Ti 0.75 O 3 ceramic. The simulated S11 parameter that was obtained exhibits superior return loss and excellent efficiency at 3.3 GHz. We have shown the input impedance, gain, and radiation pattern at φ = 0° and φ = 90°. It has been shown how the electric and magnetic fields are distributed in DRA. Furthermore, the simulated result has been used to obtain the bandwidth, VSWR, and mismatch loss.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
Microstrip Patch Antenna with BiNbO4(V2O5) Substrate and Copper Periodic Structures

Igor Ramon Sinimbú Miranda,Fiterlinge Martins de Sousa,Fabio Barros de Sousa,Jorge Everaldo de Oliveira,Marcos Benedito Caldas Costa

DOI: https://doi.org/10.1590/1980-5373-mr-2020-0487

2021-01-01

Materials Research

Abstract:The use of high permittivity materials on substrates of a microstrip antenna was developed with Bismuth Niobate ceramic doped with vanadium Oxide (BiNbO4 (V2O5)) and compared with an antenna of silicon dioxide substrate (SiO2) using Ansys software HFSS and CST Studio. The ceramic antenna has -20 dB at 3.5 GHz and the silicon dioxide antenna -24.7 dB of reflection coefficient. The bandwidth values are 80 MHz for the bismuth ceramic antenna and 100 MHz for the silica antenna. The results demonstrate that the proposed BiNbO4 antenna has great advantage compared to those mentioned in terms of volume reduction, presenting results similar to those antennas with higher volume. In addition, we use copper periodic structures (EBG) in order to increase the gain in associated with the use of BiNbO4 with addition of V2O5 on the antenna substrate leading to a reduction in the total volume. Therefore, the proposed Bismuth Niobate antenna proves to be an excellent alternative for 5G technology and microwave S band (2-4 GHz) devices, highlighting the mentioned advantages.
Microwave dielectric properties of novel Na2Mg5-xZnx(MoO4)6 (x = 0–0.09) ceramics for ULTCC applications

Cheng-Liang Huang,Jyun-Lin Huang,Tsung-Hsien Hsu

DOI: https://doi.org/10.1016/j.materresbull.2021.111355

IF: 5.6

2021-09-01

Materials Research Bulletin

Abstract:Novel Na2Mg5-xZnx(MoO4)6 (x = 0–0.09) microwave dielectrics were synthesized for ULTCC (ultra-low temperature co-fired ceramics) applications while the effect of Zn substitution on the microwave dielectric properties of the ceramics was systematically investigated. The Raman spectrum of the specimen was also analyzed. All samples can be sintered at a temperature lower than 610 °C and formed a triclinic structured solid solution with a space group of P-1 (2). Microwave dielectric properties of the specimens can be dramatically enhanced with minutely substituting Mg with Zn. Specimen with x = 0.07 at 570 °C revealed the highest Q×f of 46,000 GHz along with εr of 7.62 and τf of –25.3 ppm/°C. With 1 mol% of TiO2 added, remarkable values combined an εr of 8.8, a Q×f of 31,100 GHz and a τf of –4.2 ppm/°C, can all be achieved for the ceramic sintered at 570 °C. Since the specimen is chemically compatible with the Al electrode, we anticipate that the ULTCC candidate material so investigated would be highly promising for today’s high-frequency 5 G applications.

materials science, multidisciplinary
Microwave Dielectric Properties of Mg1.8R0.2Al4Si5O18 (R = Mg, Ca, Sr, Ba, Mn, Co, Ni, Cu, Zn) Cordierite Ceramics and Their Application for 5G Microstrip Patch Antenna

Weichao Lou,Kaixin Song,Fayaz Hussain,Amir Khesro,Jianwei Zhao,Hadi Barzegar Bafrooei,Tao Zhou,Bing Liu,Minmin Mao,Kuiwen Xu,Ehsan Taheri-nassaj,Di Zhou,Shaojin Luo,Shikuan Sun,Huixing Lin,Dawei Wang

DOI: https://doi.org/10.1016/j.jeurceramsoc.2021.12.050

IF: 5.7

2021-01-01

Journal of the European Ceramic Society

Abstract:In this work, the effects of divalent ions on the phase structure, microstructure, and microwave dielectric properties of Mg1.8R0.2Al4Si5O18 (R = Mg, Ca, Sr, Ba, Mn, Co, Ni, Cu, Zn) cordierite ceramics were investigated. Complex chemical bond theory, Raman spectrum and infrared reflectance spectrum were employed to understand the relationship among structural characteristics, vibration modes and microwave dielectric properties for alkaline earth and transitional metal divalent elements doped cordierite ceramics. The optimal microwave dielectric properties were obtained for Mg1.8Ni0.2Al4Si5O18 with εr of 4.53, Q×f of 61,880 GHz and τf of -32 ppm/℃. Finally, a 5G-Sub 6GHz patch antennas with a central frequency of 4.91 GHz was successfully designed and fabricated using a Mg1.8Ni0.2Al4Si5O18 substrate. The antenna exhibited excellent performance with a gain of 5.83 dBi and an efficiency of 76 %, showing promise to be employed in 5 G/6G millimeter-wave communication technology.
Preparation and Dielectric Properties of Li2ZnTi3O8 Nanoparticles by Sol-gel Method

Hu Liang,Yu Dan,Xu Nuoxin,Cheng Di,Zhang Qilong

2016-01-01

Rare Metal Materials and Engineering

Abstract:A surfactant assisted sol-gel process was adopted to synthesize Li2ZnTi3O8 nanoparticles, which was then used to prepare dielectric ceramics. The phase composition, particle morphology and size distribution of the nanoparticles were characterized by XRD and TEM, respectively. The crystalline phases and microstructure of the ceramics were also determined by XRD and SEM, respectively. The effect of nanoparticles on the sintering behavior and microwave dielectric properties of the ceramics was also investigated. The obtained Li2ZnTi3O8 nanoparticles have an average particle size of 40 similar to 70 nm and narrow distribution. Well -densified Li2ZnTi3O8 ceramics can be prepared from as synthesized nanoparticles at lower sintering temperature of 950 degrees C and they obtain good dielectric properties (epsilon(r) = 25.12 and Q x f = 47,069 GHz). The Li2ZnTi3O8 ceramics synthesized by the sol-gel method are candidates for low temperature co-firing ceramics application.
Design of a High-Efficiency and -Gain Antenna Using Novel Low-Loss, Temperature-Stable Li 2 Ti 1 – x (Cu 1/3 Nb 2/3 ) x O 3 Microwave Dielectric Ceramics

Huan-Huan Guo,Mao-Sen Fu,Di Zhou,Chao Du,Peng-Jian Wang,Li-Xia Pang,Wen-Feng Liu,Antonio Sergio Bezerra Sombra,Jin-Zhan Su

DOI: https://doi.org/10.1021/acsami.0c18836

2020-12-24

Abstract:Microwave dielectric ceramics are vital for filters, dielectric resonators, and dielectric antennas in the 5G era. It was found that the (Cu1/3Nb2/3)4+ substitution can effectively adjust the TCF (temperature coefficient of resonant frequency) of Li2TiO3 and simultaneously increase its Q × f (Q and f denote the quality factor and the resonant frequency, respectively) value. Notably, excellent microwave dielectric properties (εr (permittivity) ≈ 18.3, Q × f ≈ 77,840 GHz, and TCF ≈ +9.8 ppm/°C) were achieved in the Li2Ti0.8(Cu1/3Nb2/3)0.2O3 (LTCN0.2) ceramic sintered at 1140 °C. Additionally, the sintering temperature of LTCN0.2 was reduced to 860 °C by the addition of 3 wt % H3BO3, exhibiting superior microwave dielectric properties (εr ≈ 21.0, Q × f ≈ 51,940 GHz, and TCF ≈ 1.4 ppm/°C) and being chemically compatible with silver. Moreover, LTCN0.2 + 3 wt % H3BO3 ceramics were designed as a patch antenna and a dielectric resonator antenna, both of which showed high simulated radiation efficiencies (88.4 and 93%) and gains (4.1 and 4.03 dBi) at the center frequencies (2.49 and 10.19 GHz). The LTCN0.2 + 3 wt % H3BO3 materials have promising future application for either 5G mobile communication devices and/or in low-temperature co-fired ceramic technology owing to their high Q, low sintering temperature, small density, and good temperature stability.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c18836?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c18836</a>.Refined lattice parameters of LTCNx (0 ≤ x ≤ 0.4) ceramics (Table S1), Raman spectra of LTCNx (0 ≤ x ≤ 0.4) ceramics (Figure S1), SEM images and densities of the LTCNx (0 ≤ x ≤ 0.4) specimens (Figure S2), phonon parameters achieved from the fitting of the infrared reflectivity spectra of the LTCN0.2 specimen (Table S2), phonon parameters achieved from the fitting of the infrared reflectivity spectra of the LTCN0.2 + 3 wt % H3BO3 ceramic (Table S3), and optimized parameters of the proposed patch antenna (Table S4) (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c18836/suppl_file/am0c18836_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

materials science, multidisciplinary,nanoscience & nanotechnology
New Three-Phase Polymer-Ceramic Composite Materials for Miniaturized Microwave Antennas

Li Zhang,Jie Zhang,Zhenxing Yue,Longtu Li

DOI: https://doi.org/10.1063/1.4964150

IF: 1.697

2016-01-01

AIP Advances

Abstract:Unique polymer-ceramic composites for microwave antenna applications were prepared via melt extrusion using high-density polyethylene (HDPE) as the matrix and low-density polyethylene (LDPE) coated BaO–Nd2O3–TiO2 (BNT) ceramic-powders as the filler. By incorporating LDPE into the composites via a coating route, high ceramic-powder volume content (up to 50 vol%) could be achieved. The composites exhibited good microwave dielectric and thermomechanical behaviors. As BNT ceramic content increased from 10 vol% to 50 vol%, the permittivity of the composites increased from 3.45 (9 GHz) to 11.87 (7 GHz), while the dielectric loss remained lower than 0.0016. Microstrip antennas for applications in global positioning systems (GPS) were designed and fabricated from the composites containing 50 vol% BNT ceramics. The results indicate that the composites that have suitable permittivity and low dielectric loss are promising candidates for applications in miniaturized microwave devices, such as antennas.
Low sintering temperature and microwave dielectric properties of H3BO3-added Li2Ti0.85(A1/3Ta2/3)0.15O3 (A = Zn, Mg) ceramics for patch antenna application

Liu Lintao,Zhang Xiaohan,Zhang Yiyun,Du Wei,Feng Zhanbai,Wang Laiguo,Wu Haitao,Du Jialun,Xia Wangsuo

DOI: https://doi.org/10.1016/j.ceramint.2023.09.194

IF: 5.532

2023-09-01

Ceramics International

Abstract:Li2Ti0.85(A1/3Ta2/3)0.15O3 + xwt.% H3BO3 (A = Zn, Mg; 1.0 ≤ x ≤ 5.0) (LTATB x ) ceramics were fabricated by the traditional solid phase synthesis method. The LTATB x ceramics belong to monoclinic structure which was checked by the X-ray diffraction (XRD). The microstructure of Li2Ti0.85(A1/3Ta2/3)0.15O3 ceramics could be improved by the addition of H3BO3, which was directly observed by the scanning electron microscope (SEM). The optimum dielectric properties (107,490 GHz and 57,543 GHz) of Li2Ti0.85(A1/3Ta2/3)0.15O3 ceramics were obtained when the x values are equal to 1.0 and 3.0, respectively. Since the addition amount reached 5.0, the sintering temperature declined to 900 °C and 950 °C, respectively. The patch antennas prepared with LTZTB1.0 and LTMTB3.0 ceramics were simulated and measured. The results from measured indicated that the S11 parameters in LTZTB1.0 and LTMTB3.0 based patch antenna are less than −15.0 dB, and the VSWR is close to 1.0, which basically meets the application requirements of external antenna.

materials science, ceramics
High‐frequency and intrinsic dielectric properties of β‐CaSiO3 and its application: the microstrip patch antenna

Hongcheng Yang,Qian Liu,Zhan Wang,Yuandan Dong,Enzhu Li

DOI: https://doi.org/10.1111/jace.19619

IF: 4.186

2023-12-18

Journal of the American Ceramic Society

Abstract:β‐CaSiO3 LTCC material exhibit excellent stability of dielectric constant and loss at high frequencies (38;‐58 GHz and 70;‐90 GHz). A circularly polarized antenna using β‐CaSiO3 LTCC material was simulated and fabricated, which shows superior radiation efficiency (92.04 %) and gain (3.35 dBi) at the center frequency (2.5 GHz). Designing and fabricating antennas that exhibit low losses and are compact, lightweight, and highly radiation efficient are challenging in the wireless‐communication field. In this study, we simulated and fabricated microstrip patch antennas using β‐CaSiO3 low‐temperature co‐fired ceramic (LTCC) as dielectric resonator substrate. Compact ceramics that show good microwave dielectric properties (a relative dielectric constant [εr] of 6.57, high‐quality factor [Q × f] of 35 086 GHz [@14.85 GHz], and temperature coefficient of frequency [τf] of −33.56 ppm °C−1 for the optimal composition) were obtained when Li2O–CaO–B2O3–CuO glass was added to β‐CaSiO3 and sintered at 950°C. The high‐frequency properties of these composite ceramics reveal that the dielectric constant and dielectric loss are stable in the 38−58 and 70−90 GHz ranges, respectively. Furthermore, a circularly polarized antenna fabricated using a CaSiO3‐based ceramic shows a high radiation efficiency (92.04%) and gain (3.35 dBi) at a center frequency of 2.5 GHz. These β‐CaSiO3 composite ceramics offer promising prospects for high‐frequency use as well as in mobile communication applications. This study provides insight for the development of innovative antennas with new LTCC materials.

materials science, ceramics

Spontaneous neonatal esophageal perforation.

Zinc Aluminate-Based Composite Nanoparticles for Microwave Applications.

Synthesis and Fabrication of Proto-Type Microstrip Patch antenna by using Microwave Dielectric Ceramic Nanocomposite material for C-band Application

Sol–gel derived ceramic nanoparticles as an alternative material for microstrip patch antenna in WLAN applications

Experimental Investigation of Calcium-Doped Zinc Aluminate Nanoparticles as a Promising Material for Microwave Applications

Design of dual-band rectangular strip patch antenna on Bi0.5Na0.5TiO3 substrate

Design and fabrication of a C-band patch antenna using novel low permittivity SrGa2Si2O8 microwave dielectric ceramic

Investigation of BaTiO$_3$-NiO composite as compact Dielectric Resonator Antenna

Cold sintered CaTiO3-K2MoO4 microwave dielectric ceramics for integrated microstrip patch antennas

Co-substituted CuO–ZrO2–Nb2O5 composite ceramics with low-temperature sintering and low-loss for high-performance patch antenna

A novel Y3ZnAl3SiO12 microwave dielectric ceramic for microwave communication application as substrates

Crystal structure, microwave dielectric properties, and dielectric resonant antenna studies of novel low-permittivity CoAl2O4 spinel ceramics

An investigation of microwave dielectric properties of BaZr0.25Ti0.75O3 and performance of DRA for 5G application

Microstrip Patch Antenna with BiNbO4(V2O5) Substrate and Copper Periodic Structures

Microwave dielectric properties of novel Na2Mg5-xZnx(MoO4)6 (x = 0–0.09) ceramics for ULTCC applications

Microwave Dielectric Properties of Mg1.8R0.2Al4Si5O18 (R = Mg, Ca, Sr, Ba, Mn, Co, Ni, Cu, Zn) Cordierite Ceramics and Their Application for 5G Microstrip Patch Antenna

Preparation and Dielectric Properties of Li2ZnTi3O8 Nanoparticles by Sol-gel Method

Design of a High-Efficiency and -Gain Antenna Using Novel Low-Loss, Temperature-Stable Li 2 Ti 1 – x (Cu 1/3 Nb 2/3 ) x O 3 Microwave Dielectric Ceramics

New Three-Phase Polymer-Ceramic Composite Materials for Miniaturized Microwave Antennas

Low sintering temperature and microwave dielectric properties of H3BO3-added Li2Ti0.85(A1/3Ta2/3)0.15O3 (A = Zn, Mg) ceramics for patch antenna application

High‐frequency and intrinsic dielectric properties of β‐CaSiO3 and its application: the microstrip patch antenna